Gigabyte GS-R115V-RH System Installation Manual

System Installation Guide

GS-R115V-RH

GS-R115L-RH

1U Rack Mount Server

Intel

®

Pentium LGA775 Processor Serverboard

Rev. 1.0

25A08G-015V0-F00

2

GS-R115V-RH/GS-R115L-RH Rack Mount Server

Table of Content

Safety, Care and Regulatory Information................................................4

Introduction..............................................................................................8

GS-R115-RH Series Model List .............................................................8

Contents Packages ................................................................................8

Chapter 1 Features Summary.................................................................9

Chapter 2 System Hardware Installation ............................................... 11

Step 2-1: Chassis Removal and Installation .................................................................11

Step 2-2: CPU Installation............................................................................................... 12

Step 2-3: Heat Sink Installation....................................................................................... 13

Step 2-4: Memory Installation ........................................................................................ 13

Step 2-5: PCI Expansion Card Installation.................................................................... 14

Step 2-6: Hard Disk Drive Installation ............................................................................ 15

GS-R115V-RH.................................................................................................................. 15

GS-R115L-RH .................................................................................................................. 16

Step 2-7: FAN Duct Removal and Installation.............................................................. 17

Chapter 4 Appearance of GS-R115-RH ...............................................18

4-1: Front View of GS-R115V-RH.................................................................................. 18

4-2: Front View of GS-R115L-RH .................................................................................. 18

4-3: Rear View of GS-R115-RH..................................................................................... 19

4-4: Switch and LED Indicators Introduction ................................................................. 20

4-5: LAN LED Description............................................................................................... 21

4-6: Connector Icon Description..................................................................................... 22

Chapter 5 Motherboard Jumper Setting ...............................................23

5-1: GA-5EXSH-RH Motherboard Jumpper Setting...................................................... 23

Chapter 6 BIOS Setup ..........................................................................25

Main...........................................................................................................27

Advanced Processor Options ........................................................................................ 30

Advanced ...................................................................................................33

Memory Configuration..................................................................................................... 34

PCI Configuration............................................................................................................. 35

3

Table of Content

SIO ITE8718F Configuration ........................................................................................... 36

Advanced Chipset Control ............................................................................................. 41

Hardware Monitor ............................................................................................................ 42

Security ......................................................................................................45

Server.........................................................................................................47

System Management...................................................................................................... 48

Console Redirection........................................................................................................ 49

Event Log Configuration.................................................................................................. 51

Boot............................................................................................................54

Exit .............................................................................................................55

Chapter 7 INTEL RAID BIOS Configuration ...........................................61

Chapter 8 Application Driver Installation ...............................................66

A. Intel Chipset Software Installation Utilities ................................................................ 66

B. Intel LAN Driver Installation ...................................................................................... 69

C. XGI VGA Driver Installation ....................................................................................... 73

D. Intel ICH7R RAID Driver Installation.......................................................................... 76

E. Matrix Storgae Manager Utility Installation ............................................................. 78

F. DirectX 9.0C Driver Installation ................................................................................. 82

4

GS-R115V-RH/GS-R115L-RH Rack Mount Server

Safety, Care and Regulatory Information

 Important safety information

Read and follow all instructions marked on the product and in the documentation before you operate

your system. Retain all safety and operating instructions for future use.

* The product should be operated only from the type of power source indicated on the rating label.

* If your computer has a voltage selector switch, make sure that the switch is in the proper position for

your area. The voltage selector switch is set at the factory to the correct voltage.

* The plug-socket combination must be accessible at all times because it serves as the main disconnect-

ing device.

* All product shipped with a three-wire electrical grounding-type plug only fits into a grounding-type power

outlet. This is a safety feature. The equipment grounding should be in accordance with local and national

electrical codes. The equipment operates safely when it is used in accordance with its marked electrical

ratings and product usage instructions

* Do not use this product near water or a heat source.

* Set up the product on a stable work surface or so as to ensure stability of the system.

* Openings in the case are provided for ventilation. Do not block or cover these openings. Make sure you

provide adequate space around the system for ventilation when you set up your work area. Never insert

objects of any kind into the ventilation openings.

* To avoid electrical shock, always unplug all power cables and modem cables from the wall outlets

before removing covers.

* Allow the product to cool before removing covers or touching internal components.

 Precaution for Product with Laser Devices

Observe the following precautions for laser devices:

* Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than

those specified in the product's documentation.

* Only authorized service technicians should repair laser devices.

 Precaution for Product with Modems, Telecommunications, ot Local Area

Network Options

Observe the following guidelines when working with options:

* Do not connect or use a modem or telephone during a lightning storm. There may be a risk of electrical

shock from lightning.

5

Safety Information

* To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

* Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

* Disconnect the modem cable before opening a product enclosure, touching or installing internal

components, or touching an uninsulated modem cable or jack.

* Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

 Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission

limits. Neither the provider nor the manufacturer are responsible for any radio or television interference

caused by using other than recommended cables and connectors or by unauthorized changes or

modifications to this equipment. Unauthorized changes or modifications could void the user's authority to

operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

 FCC part 68 (applicable to products fitted with USA modems)

The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among

other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment.

You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may

discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not

practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with

the FCC.

6

GS-R115V-RH/GS-R115L-RH Rack Mount Server

Your telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect proper operation of your equipment. If they do, you will be notified in advance to give you an

opportunity to maintain uninterrupted telephone service.

The FCC prohibits this equipment to be connected to party lines or coin-telephone service.

The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part

68, Sec. 68.381 (c) (3)).

/ for Canadian users only /

 Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus as set out in the radio interference regulations of Industry Canada.

Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux

appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edicte par

Industrie Canada.

 DOC notice (for products fitted with an Industry Canada-compliant modem)

The Canadian Department of Communications label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational and safety

requirements. The Department does not guarantee the equipment will operate to the user satisfaction.

Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the

local Telecommunications Company. The equipment must also be installed using an acceptable method

of connection. The customer should be aware that compliance with the above conditions might not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,

may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system, if resent are connected together. This precaution

may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

7

Safety Information

NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total

load to be connected to a telephone loop which is used by the device, to prevent overloading. The

termination on a loop may consist of any combination of devices subject only to the requirement that the

sum of the Load Numbers of all the devices does not exceed 100.

/ for European users only /

CAUTION

 Danger of explosion if battery is incorrectly

replaced.

 Replace only with the same or equivalent

type recommended by the manufacturer.

 Dispose of used batteries according to the

manufacturer’s instructions.

8

GS-R115V-RH/GS-R115L-RH Rack Mount Server

; Chassis ; GA-5EXSH-RH Motherboard (Installed)

; Power Supply (Installed) ; FAN Duct x 1

; CPU Heat Sink x 1 ; Standard Floppy Drive (Installed)

; Silm type CD-ROM drive (Installed) ; Cables (RJ45)

; GS-R115V/L-RH System Installation Guide ; Case Handle Kit x 2

; Driver CD for motherboard driver & utility

Introduction

Welcome to Gigabyte GS-R115V-RH Rack mount Server System Installation Guide. The guide

provides instructions for configuration hardware for the GS-R115V-RH your system.

This installation guide will assist you in installing all the essential components for the sever system.

For your protection, please read and undertand all of the safety and operating instructions regarding your

Gigabyte Server and retain for future reference. The procedures in this guidebook assume that your are

a system or network administrator experienced in installing similar hardware.

Contents Packages

When opening the package, please ensure the system components are not damaged during the shipping.

Using the following checklist to verify the contents. If any component is missing or damaged in the

system, please contact your vendor immediately.

GS-R115-RH Series Model List

 GS-R115V-RH (Supports 2 hot-swap SATA HDDs)

 GS-R113L-RH (Supports 2 internal SATA HDDs)

9

Feature Summary

Motherboard  GA-5EXSH-RH

Processor Supported  Supports single Intel

®

Pentium

®

4/Pentium

®

D processor

 Intel Pentium

®

Dual Core in LGA 775 socket

 Supports 800/1066MHz FSB

 L2 cache on-die per processor from 4M

Chipset  Intel

®

3000 Chipset

 Intel

®

ICH7R

System Memory:

Memory Capacity  4 x DDRII socket up to 8 GB

Memory Type  Un-buffered DDRII 533/667

DIMM Size  Support 256MB, 512MB, 1GB, and 2GB memory

Error Correction:  Single-bit Errors Correction, Multiple Bit Errors Detection

Expansion Slot  1 Riser card supports 1 PCI-E x8 and 1 PCI-E x4 add-on cards

 1 Riser card supports 1 PCI-E x8 (low-profile) and

1 PCI-X 100/133MHz add-on cards

SATA RAID controller  ICH7R

 Supports SATA RAID 0,1

Cooling Fans:  5 X System Fan

Integrated LANs:

Controller  Dual Intel 82573L

®

Gigabit Ethernet controllers

Integrated Graphics:

Controller  XGI Volari Z7

Graphics Memory  16MB SDRAM

Mass Storage System  2 x Hot-Swap SATA HDDs (GS-R115V-RH)

 2 x Internal SATA HDDs (GS-R115L-RH)

 1 x Standard Type FDD

 1 x Slim Type CD-ROM

 Optional DVD Combo (Optional device)

Chapter 1 Features Summary

10

GS-R115V-RH/GS-R115L-RH Rack Mount Server

Super I/O

Controller  ITE IT8718F Super I/O

Built-in I/O  1 x Serial port (COM)

 3 x USB 2.0 dual-port connector (1 at front panel)

 1 x VGA connector

 2 x RJ45 LAN ports

 P/S 2 Keyboard and Mouse Connectors

 1 x RJ45 ports for console redirection

System BIOS:

BIOS Type  Phoenix BIOS on 8Mb flash ROM

Server Management Functions: (Optional device)

BMC Chip  H8S IPMI 2.0 controller

Failure Detection  IPMI 2.0 specification of Server management

Event Logging  32KB Nonvolatile Memory to Log System Failure Events

Remote Management  Follow the IPMI 2.0 specification of Server management

Environment

Ambient Temperature  Operating Temperature: 5

o

C to 35

o

C

 Non-operating Temperature: 0

o

C to 50

o

C

Relative Humidity  10-80% operating Humidity at 30

o

C

System Dimention:  427.5mm x 521mm x 42.6 mm

Electrical Power Supply  Single Power Supply 300W

11

Hardware Installation Process

Please observe the safety information in chapter “Important Safety Information”

Do not expose the server to extreme environmental conditions. Protect it from dust,

humidity, and heat.

Step 2-1: Chassis Removal and Installation

Step 1 Loosen the thumbscrew from the back of the server.

Step 2 Push down the indentation located at two sides of the chassis, and slide toward to remove the

top cover.

Step 3 Reverse Step 1, and 2 to replace the chassis cover.

Chapter 2 System Hardware Installation

Step 2

Note: Before installing CPU, you must remove the FAN duct. For FAN duct removal, please

see Sub-section 2-7 “FAN Duct Removal and Installtion” for detail instruction.

Step 1

Thumbscres

12

GS-R115V-RH/GS-R115L-RH Rack Mount Server

Step 2-2: CPU Installation

Please make sure the CPU type and speed that are supported by the motherboard.

Step 3

Step 1

Step 2

Step 4

Step 1 Raise the metal locking lever on the socket.

Step 2 Remove the plastic covering on the CPU socket.

Step 3 Lift the metal cover.

Step 4 Insert the CPU with the correct orientation. The CPU only fits in one orientation.

Step 5 Once the CPU is properly placed, please replace the metal cover and push the metal

lever back into locked position.

13

Hardware Installation Process

Step 2-3: Heat Sink Installation

Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well

remember to apply the thermal conductivity compound on the CPU.

Step 2 Seat the heat sink in the retention modules with the four screws. Installation completed.

Step 2-4: Memory Installation

Step 2

Step 1

1. Unlock a DIMM socket by pressing the retaining clips outwards.

2. Aling a DIMM on the socket such that the notch on the DIMM exactly match the notches in the

socket.

3. Firmly insert the DIMMinto the socket until the retaining clips snap back in place.

4. When installing the DIMM into the DIMM socket, we recommend to populate one DIMM in

Channel A module and one in Channel B module for best performance.

Please note that each logical DIMM must be made of two identical DIMMs having the same

device size on each and the same DIMM size.

5. Reverse the installation steps when you wish to remove the DIMM module.

Retaining Clip

14

GS-R115V-RH/GS-R115L-RH Rack Mount Server

Step 2-5: PCI Expansion Card Installation

GS-R115V-RH provides expansion riser slots for one PCI-X full-height/full-length 100/133MHz; and one

with PCI-E x8 slot. To install the peripheral, please go through the following steps.

Note!! Before installing the PCI expansion card, please check the card size limitation. Size limitation

for PCI-X full-height/full-length is 228.5 mm x 91.5 mm; size limitation for Low-Profile Card : 167.5 mm

x 56 mm .

Step 1 Lift the riser bracket slightly, then pull it out from the server chassis.

Step 2 Lossen the screw on the riser bracket.

Step 2 Align the expansion card with the guiding groove. Slide the expansion card into the slot until the

card firmly seats.

Step 3 Align the riser bracket to the system module (see the arrow direction mark 1), and push

it to locked position.

Step 4 Reverse Step 1 & 2 to lock the riser bracket firmly. Installation completed.

Step 1

Step 2

Step 3

Step 4

15

Hardware Installation Process

Step 2-6: Hard Disk Drive Installation

Step 1

Step 2

Step 1 Press the release button and pull the blank out of the drive bay.

Step 2 Remove the plastic hard disk tray.

Step 3 Slide hard disk into blank and secure it with screws.

Step 4 To replace the hard drive blank, slide the blank into the bay until it locks into place. Connect cable

and power.

Step 5 Place the hard disk into the server system.

Step 3

GS-R115V-RH

16

GS-R115V-RH/GS-R115L-RH Rack Mount Server

Step 1 Lossen the screws securing the hard drive plate.

Step 2 Slide toward to remove the hard drive plate from system.

Step 3 Place hard disk on the plate and lock hard drive with 4 screws.

Step 4 Replace the hard drive plate, slide the blank into the bay until it locks into place.Connect HDD

power cable.

Step 5 Reverse step 1, 2, 3 and 4 to complete the HDD installtion.

GS-R115L-RH

Step 1

Remove

Step 2

17

Hardware Installation Process

Step 2-7: FAN Duct Removal and Installation

Step 1 Pull up the screw-holder and lossen the thumbscrews. Lift up to remove the fan duct.

Step 2 For FAN Duct Installation, place the fan duct on the top of heat sinks. Fasten the screws to the

locked position and push down the screw-holders.

Step 1

Step 2

18

GS-R115V-RH/GS-R115L-RH Rack Mount Server

4-1: Front View of GS-R115V-RH

Chapter 4 Appearance of GS-R115-RH













MOR-DCepyTmilS



sDDHATASpawS-toH



rotcennoCBSU



sDEL



)noitcerideRelosnoCroF(54JR

4-2: Front View of GS-R115L-RH



MOR-DCepyTmilS



ypoolFdradnatS



rotcennoCBSU



sDEL



)noitcerideRelosnoCroF(54JR











System Appearance

19

4-3: Rear View of GS-R115-RH











 



rewoP



troPAGV



troPMOC



tolSresiReliforPwoL



tolSresiRhtgnel-lluF/ezis-lluF



rotcennoCdraobyeK



rotcennoC

esuoM



srotcennoCBSU



stroP2&1NAL

20

GS-R115V-RH/GS-R115L-RH Rack Mount Server

4-4: Switch and LED Indicators Introduction

Power/Sleep

LAN1/2 Activities

HDD

Status

Name

Power

Status

HDD

LAN1

Activity

LAN2

Activity

Color Condition Description

Green On Power On

Green Blink Sleep (S1)

-- Off Power Off (S4/S5)

Green On System Ready On/ Alarm

Amber Blink System Ready but deqraded,DIMM Killed.

Amber On Critical Alarm:Critical FANs Failure

-- Off System Not Ready/ Post error/NMI event/

No Power

Green Blink Hard Disk Drive Access

-- Off No Access and No HDD Fault

Green On LAN Link / No access

Green Blink LAN access

-- Off Idle

Green On LAN Link / No access

Green Blink LAN access

-- Off Idle

Page is loading ...

Gigabyte GS-R115V-RH System Installation Manual

This manual is also suitable for

Gigabyte GS-R115V-RH System Installation Manual

Related papers

Other documents