Eaton COOPER POWER SERIES Installation guide

COOPER POWER SERIES
Eaton
Brand
Eaton
Model
COOPER POWER SERIES
Type
Installation guide

Eaton COOPER POWER SERIES 600 A 15 and 25 kV class PUSH-OP insulated standoff bushing provides a single deadbreak interface for isolating and sectionalizing an energized cable. It simplifies temporary or permanent parking of energized connectors with its insulated standoff bushing. Fully-shielded, submersible connection ensures safe deadfront construction. Its bracket and latch mechanism facilitate easy installation without threading operations. The device meets IEEE Std 386™-2006 standards and comes with a drain wire lug for grounding.

Eaton COOPER POWER SERIES 600 A 15 and 25 kV class PUSH-OP insulated standoff bushing provides a single deadbreak interface for isolating and sectionalizing an energized cable. It simplifies temporary or permanent parking of energized connectors with its insulated standoff bushing. Fully-shielded, submersible connection ensures safe deadfront construction. Its bracket and latch mechanism facilitate easy installation without threading operations. The device meets IEEE Std 386™-2006 standards and comes with a drain wire lug for grounding.

600 A 15 and 25 kV class PUSH-OP
™
insulated standoff bushing
General
Eaton meets the full requirements of IEEE
Std 386™-2006 standard, Separable Insulated
Connector Systems with its Cooper Power™
series 600 A, 15 and 25 kV insulated PUSH-OP™
standoff bushing.
The bushing provides a single deadbreak interface
made of high quality insulating epoxy material.
It is used in switchgear, transformers, and
other apparatus to isolate and sec tion al ize an
energized cable. Temporary or permanent parking
of energized 600 A 15 and 25 kV PUSH-OP
deadbreak connectors is simplified with the use of
an insulated standoff bushing.
The PUSH-OP insulated standoff bushing is
de signed to be installed in the parking stand
mounted on a switchgear, transformer, or other
apparatus. A drain wire lug is pro vid ed on the
standoff bracket for at tach ment of a drain wire
lead to ensure deadfront construction. The bushing
provides a fully-shielded, submersible connection
for deadbreak operation.
All standoff bushing brackets have a stainless
steel eyebolt with a brass pressure foot. The
bushing body is bolted to a stainless steel base
bracket using a stainless steel bolt. The bracket
and latch mechanism provides easy installation
of a PUSH-OP connector without any threading
operations.
Installation
A clampstick tool is used to place the standoff
bushing in the parking stand on the front plate of
the apparatus. The PUSH-OP connector is then
installed onto the standoff bushing tap. Refer to
Service Information S600-65-1 600 A 15/25 and
35 kV Class PUSH-OP Insulated Standoff Bushing
Installation Instructions for complete installation
details.
Production tests
Tests are conducted in accordance with IEEE Std
386™-2006 standard.
•
ac 60 Hz 1 Minute Withstand
• 40 kV
•
Minimum Corona Voltage Level
• 19 kV
Tests are conducted in accordance with Eaton
requirements.
•
Physical Inspection
•
Periodic Dissection
•
Periodic Fluoroscopic Analysis
Deadbreak Connectors
Catalog Data
CA650 043EN
Effective April 2015
Supersedes 600-25 August 2002
COOPER POWER
SERIES
Figure 1. Front view shows standoff bushing and latch mechanism. Side view shows standoff bushing and latch mechanism with
bracket assembly.
ote:N Dimensions given are for reference only.
4.8 "
(121.9 mm)
13 "
(330.2 mm)
5.25 "
(133.4 mm)
2.37 "
(60.2 mm)
4.0 "
(101.6 mm)
EYEBOLT
Stainless Steel Eyebolt
with brass pressure foot
rigidly secures standoff
bushing to parking
stand.
STAINLESS STEEL (Series 300)
BRACKET AND LATCH
MECHANISM accepts 600 A
PUSH-OP connectors and
facilitates "threadless"
operability.
EPOXY INSULATION
High quality Molded Epoxy
Insulation provides excellent
electrical, thermal and
mechanical reliability for
insulated standoff bushings.
PULLING EYE
Stainless Steel Eye
facilitates hotstick
operability with no
other tool required.
SIDE VIEW
5.50 "
(139.7 mm)
FRONT VIEW
STAINLESS STEEL
BRACKET ASSEMBLY
Stainless Steel
Mounting Bracket
has drain wire lug
for bracket and
shield grounding.
DRAIN WIRE LUG
Provides for attachment
of drain wire.
Figure 2. PUSH-OP stacking dimensions.
TANK
WALL
S8
S7
15/25 kV
S7 0.75" (19 mm)
S8 5.14" (130.6 mm)
Table 1. Voltage Ratings and Characteristics —Insulated
Standoff Bushing
Description kV
Standard Voltage Class 25
Maximum Rating Phase-to-Ground 15.2
ac 60 Hz 1 Minute Withstand 40
dc 15 Minute Withstand 78
BIL and Full Wave Crest 125
Minimum Corona Voltage Level 19
Voltage ratings and characteristics are in accordance with IEEE Std 386™-2006 standard.
2
Catalog Data CA650043EN
Effective April 2015
600 A 15/25 kV class PUSH-OP insulated standoff bushing
www.eaton.com/cooperpowerseries
Ordering information
To order a 15 and 25 kV Class PUSH-OP Standoff Bushing Kit, refer
to Table 2.
Each kit contains:
•
Standoff Bushing with Bracket
•
Shipping Cap (not for energized operation)
•
Silicone Lubricant
•
Installation Instruction Sheet
Table 2. Standoff Bushing Kit
Description Catalog Number
Insulated Bushing PISB625
Insulated Standoff Bushing with Hitch Pin PISB625HP
3
Catalog Data CA650043EN
Effective April 2015
600 A 15/25 kV class PUSH-OP insulated standoff bushing
www.eaton.com/cooperpowerseries
Eaton, Cooper Power, and PUSH-OP are
trademarks of Eaton in the U.S. and other
countries. You are not permitted to use these
trademarks without the prior witten consent
of Eaton.
IEEE Std 386™-2006 and IEEE Std 592™-2007
standards are trademarks of the Institute
of Electrical and Electronics Engineers,
Inc., (IEEE). This publication/product is not
endorsed or approved by the IEEE.
600 A 15/25 kV class PUSH-OP insulated standoff bushingCatalog Data CA650043EN
Effective April 2015
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Cooper Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. CA650043EN
For Eaton's Cooper Power series PUSH-OP
bushing product information call
1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Eaton COOPER POWER SERIES Installation guide

COOPER POWER SERIES
Eaton
Brand
Eaton
Model
COOPER POWER SERIES
Type
Installation guide

Eaton COOPER POWER SERIES 600 A 15 and 25 kV class PUSH-OP insulated standoff bushing provides a single deadbreak interface for isolating and sectionalizing an energized cable. It simplifies temporary or permanent parking of energized connectors with its insulated standoff bushing. Fully-shielded, submersible connection ensures safe deadfront construction. Its bracket and latch mechanism facilitate easy installation without threading operations. The device meets IEEE Std 386™-2006 standards and comes with a drain wire lug for grounding.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents