-1-
Contents
Safety and warnings..........................................................................................................2- 3
Introduction.....................................................................................................................4
Installation...................................................................................................................... 5-15
Remote Controller........................................................................................................... 1 6
TV Operation..................................................................................................................17-21
Trouble shooting............................................................................................................ 2 2
-2-
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, install in
accordance with the instructions.
8) Do not install near any heat sources such as
radiations, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
plug. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protected the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Unplug this apparatus during lighting storms or
when unused for long periods of time.
13) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been
dropped.
14) Mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
15) The ventilation should not be impeded by
covering the ventilation openings with items, such
as newspapers, table-cloth, curtains, etc.
16) No naked flame sources, such as lighted
candles, should be placed on the apparatus.
17) Attention should be drawn to the environmental
aspects of battery disposal.
18) The use of apparatus in moderate climate.
19) The apparatus shall not be exposed to dripping
or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user accessible
parts. When servicing use only
identical replacement parts.
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible harm to
the environment or human health from
uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of
material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was
purchased. They can take this product for
environmental safe recycling.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OFELECTRIC SHOCK
DO NOT OPEN!
CAUTION
The symbol indicates that dangerous voltages
constituting a risk of electric shock are present
within this unit.
The symbol indicates that there are important
operating and maintenance instructions in the
literaturaccompanying this unit.
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
WARNING:
The batteries shall not be exposed to excessive
heat such as sunshine, fire or the like.
WARNING:
-3-
High voltages are used in the operation of this television
receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
SAFETY AND WARNINGS
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of
electrical components.
Do not trap the power supply cord under the television
receiver.
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.
Do not place your television on an unstable cart, stand,
shelf or table. Serious injury to an individual , and damage
to the television, may result if it falls.
When the television receiver is not used for an
extended period of time, it is advisable to disconnect
the AC power cord from the AC outlet.
Avoid exposing the television receiver to direct sunlight
and other sources of heat. Do not stand the television
receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
the television.
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.
INTRODUCTION
-4-
Main features
Accessories
Used as Television, display terminal, PC display
High luminance, wide viewing angle
Can store 200 TV programs
HDMI interface
5 Multi-Media player (USB);
Infrared Remote Controller............
1
User s Manual...............................1’
Battery(AAA)...............................2
SPECIFICATIONS
VKC19HH
Viewing Picture Size (Diagonal)
Resolution
Aspect Ratio
TV System
Receiving Channel
Power consumption
Video Signal System
Input Power Voltage
Audio Output Power
1366 x 768
16 : 9
PAL/BG
PAL/NTSC/SECAM
1 TO 200
THD 7%
2x3W
40W
AC 110-240V 50/60Hz
1366 x 768 1366 x 7681920 x 1080
2x8W
45W 50W 60W
2x3W 2x3W
Viewing Picture Size (Diagonal)
Resolution
Aspect Ratio
TV System
Receiving Channel
Power consumption
Video Signal System
Input Power Voltage
Audio Output Power
1366 x 768
16 : 9
PAL/BG
PAL/NTSC/SECAM
THD 7%
2x8W
75W
AC 110-240V 50/60Hz
1920 x 1080
100W 125W
1920 x 1080 1920 x 1080
135W
2x8W 2x10W 2x10W
VKC22FH VKC24HH VKC28HH
VKC32HH VKC39FH VKC50FH VKC55FH
1 TO 200
Viewing Picture Size (Diagonal)
Resolution
Aspect Ratio
TV System
Receiving Channel
Power consumption
Video Signal System
Input Power Voltage
Audio Output Power
1920 x 1080
16 : 9
PAL/BG
PAL/NTSC/SECAM
THD 7%
2x10W
120W
AC 110-240V 50/60Hz
VKC46FH
1 TO 200
-5-
Installation of Standbase Assembly(19"/22"/24")
Prepare to place the TV with the display side down on a flat surface. Due to the size and weight of this
TV, the use of 2 people is recommended when moving it. Ensure the table or desk you use provides
a flat, totally clean surface, and use a soft cloth between the face of the TV and the table to protect the
TV's screen.
1. Locate the bottom bracket into the gap in the bottom of the TV, and check that it is securely held in
place by its screws, as per a) below.
2. Gently slide the fitted bracket at the bottom of the TV into the slot in the base stand. Secure the base
stand using the 3 pcs supplied screws, as per b) below, and check that each screw is firmly tightened.
Installation of WallMount Assembly(19"/22'/24")
For wall mounting with an optional bracket, please read the following instructions in conjunction with the
bracket's instructions. Make sure qualified service personnel perform the operation.
This television can be wall mounted as follows:
1.Place the LED LCD Television face down onto a solid surface. Please place some soft material over
the front of the screen to protect it from any damage. The LCD panel is a fragile component, and must
be suitably protected when removing the base stand. Be sure that no hard or sharp objects can come
into contact with the screen's surface. Do not exert pressure on the front of the unit at any time, as this
may damage the LCD screen.
2.Remove the 1 screws from the lower part of the television, where the base joins to the TV, and take
away the stand (put the stand and screws somewhere safe for future use).
3.Use the M4 screws provided to fix the TV onto a wall mounting bracket (not included) via the
four VESA standard holes on the back of the television.
a) b)
INSTALLATION
100m m
-6-
Installation of Standbase Assembly(28"/32")
Prepare to place the TV with the display side down on a flat surface. Due to the size and weight of this
TV, the use of 2 people is recommended when moving it. Ensure the table or desk you use provides
a flat, totally clean surface, and use a soft cloth between the face of the TV and the table to protect the
TV's screen.
1. Locate the bottom bracket into the gap in the bottom of the TV, and check that it is securely held in
place by its screws, as per a) below.
2. Gently slide the fitted bracket at the bottom of the TV into the slot in the base stand. Secure the base
stand using the 4 pcs supplied screws, as per b) below, and check that each screw is firmly tightened.
Installation of WallMount Assembly(28"/32")
For wall mounting with an optional bracket, please read the following instructions in conjunction with the
bracket's instructions. Make sure qualified service personnel perform the operation.
This television can be wall mounted as follows:
1.Place the LED LCD Television face down onto a solid surface. Please place some soft material over
the front of the screen to protect it from any damage. The LCD panel is a fragile component, and must
be suitably protected when removing the base stand. Be sure that no hard or sharp objects can come
into contact with the screen's surface. Do not exert pressure on the front of the unit at any time, as this
may damage the LCD screen.
2.Remove the 3 screws from the lower part of the television, where the base joins to the TV, and take
away the stand (put the stand and screws somewhere safe for future use).
3.Use the M4 screws provided to fix the TV onto a wall mounting bracket (not included) via the
four VESA standard holes on the back of the television.
a) b)
INSTALLATION
-7-
Installation of Standbase Assembly(40"/ 50"/55")46"/
Prepare to place the TV with the display side down on a flat surface. Due to the size and weight of this
TV, the use of 2 people is recommended when moving it. Ensure the table or desk you use provides
a flat, totally clean surface, and use a soft cloth between the face of the TV and the table to protect the
TV's screen.
1. Locate the bottom bracket into the gap in the bottom of the TV, and check that it is securely held in
place by its screws, as per a) below.
2. Gently slide the fitted bracket at the bottom of the TV into the slot in the base stand. Secure the base
stand using the 4 pcs supplied screws, as per b) below, and check that each screw is firmly tightened.
Installation of WallMount Assembly( 40"/46"/50"/)55"
For wall mounting with an optional bracket, please read the following instructions in conjunction with the
bracket's instructions. Make sure qualified service personnel perform the operation.
This television can be wall mounted as follows:
1.Place the LED LCD Television face down onto a solid surface. Please place some soft material over
the front of the screen to protect it from any damage. The LCD panel is a fragile component, and must
be suitably protected when removing the base stand. Be sure that no hard or sharp objects can come
into contact with the screen's surface. Do not exert pressure on the front of the unit at any time, as this
may damage the LCD screen.
2.Remove the 4 screws from the lower part of the television, where the base joins to the TV, and take
away the stand (put the stand and screws somewhere safe for future use).
3.Use the M6 screws provided to fix the TV onto a wall mounting bracket (not included) via the
four VESA standard holes on the back of the television.
a) b)
INSTALLATION
400200
-8-
Rear AV Connectivities (19"/22"/24"/28")
All the terminals are(from left to right):
, VIDEO, AUDIO INPUTSAC POWER SOCKET , AV OUTPUT.
Note: VIDEO and YPbPr share one audio channel.
Rear AV side Connectivities(19"/22"/24"/28")
INSTALLATION
Front panel
Key Board Instructions (19" /22" /24" /28")
1: Remote control sensor.
2: Indicator LED: RED STANDBY.
3: Key board
1 SOURCE
2 MENU
3 CH+/CH-
4 VOL+/VOL-
5. STANDBY
“ ” “ ”
“ ” “ ”
“ ” “ ”
Display the input source menu.
Display main MENU.
In TV mode press CH+ or CH- to change
the channel up and down.
In MENU mode, press CH+ or CH- to select
items.
Adjust sound level.
In MENU mode, press VOL+ or VOL- to
adjust the item that you selected.
Press this button to turn the unit ON from
STANDBY mode.
Press it again to turn the set back to STANDBY.
All the terminals are (from left to right):
USB, HDMI2, HDMI1, YPbPr, HEADPHONE, PC AUDIO, VGA, RF.
Note: When HDMI port get DVI signal, the audio signal receives from the PC
Audio channel.
30 30
1
2
3
SOURCE
MENU
VOL+
VOL-
CH+
CH-
STANDBY
HDMI2 HDMI1USB
VGA
RF
Y Pb Pr
PC AUDIO
VIDE O
L R
AV IN
VIDE O
L R
AV OUT
-9-
All the terminals are(from left to right):
, VIDEO, AUDIO INPUTSAC POWER SOCKET , AV OUTPUT.
Note: VIDEO and YPbPr share one audio channel.
INSTALLATION
Front panel
Key Board Instructions (32")
1: Remote control sensor.
2: Indicator LED: RED STANDBY.
3: Key board
1 SOURCE
2 MENU
3 CH+/CH-
4 VOL+/VOL-
5. STANDBY
“ ” “ ”
“ ” “ ”
“ ” “ ”
Display the input source menu.
Display main MENU.
In TV mode press CH+ or CH- to change
the channel up and down.
In MENU mode, press CH+ or CH- to select
items.
Adjust sound level.
In MENU mode, press VOL+ or VOL- to
adjust the item that you selected.
Press this button to turn the unit ON from
STANDBY mode.
Press it again to turn the set back to STANDBY.
All the terminals are (from left to right):
USB, HDMI2, HDMI1, YPbPr, HEADPHONE, PC AUDIO, VGA, RF.
Note: When HDMI port get DVI signal, the audio signal receives from the PC
Audio channel.
30 30
1
2
3
SOURCE
MENU
VOL+
VOL-
CH+
CH-
STANDBY
HDMI2
HDMI1
USB
VGA
Y
Pb
Pr
HEADPHONE
PC AUDIO
R F
Rear AV side Connectivities(32")
Rear AV Connectivities (32")
Rear AV Connectivities ( )40"/46"/50"/55"
All the terminals are(from left to right):
, VIDEO, AUDIO INPUTSAC POWER SOCKET , YPbPr.
Note: VIDEO and YPbPr share one audio channel.
Rear AV side Connectivities( )40"/46"/50"/55"
INSTALLATION
Front panel
Key Board Instructions ( )40"/46"/50"/55"
1: Remote control sensor.
2: Indicator LED: RED STANDBY.
3: Key board
1 SOURCE
2 MENU
3 CH+/CH-
4 VOL+/VOL-
5. STANDBY
“ ” “ ”
“ ” “ ”
“ ” “ ”
Display the input source menu.
Display main MENU.
In TV mode press CH+ or CH- to change
the channel up and down.
In MENU mode, press CH+ or CH- to select
items.
Adjust sound level.
In MENU mode, press VOL+ or VOL- to
adjust the item that you selected.
Press this button to turn the unit ON from
STANDBY mode.
Press it again to turn the set back to STANDBY.
30 30
1
2
3
SOURCE
MENU
VOL+
VOL-
CH+
CH-
STANDBY
All the terminals are (from left to right):
HDMI2, HDMI1, USB, AV OUTPUT, PC AUDIO, VGA, RF.
Note: When HDMI port get DVI signal, the audio signal receives from the PC
Audio channel.
AV OUTPUT
HDMI2 HDMI1 USB R FVGAPC AUDIOVIDEO L R
-10-
INSTALLATION
-11-
STEPS:
PC Connectivity
Be sure both the TV and computer are set to Power off.
1.Connect VGA and audio cable.
2.Connect the power cord.
3.Power on the TV, switch to PC mode.
4.Power on the PC.
This sequence is very important.
Note:
Aerial connections: IEC(female).
Input impendance: 75 unbalanced.
ANTENNA
HDMI2
HDMI1
USB
VGA
Y
Pb
Pr
HEADPHONE
PC AUDIO
R F
AV OUTPUT
HDMI2 HDMI1 USB R FVGAPC AUDIOVIDEO L R
HDMI2 HDMI1USB
VGA
RF
Y Pb Pr
PC AUDIO
FOR 19"/22"/24"/28"
FOR 32"
FOR 40"/46"/50"/55"
INSTALLATION
-12-
PRESET MODE (PC)
NOTE: PC V.Freq.(Hz) not more than 60Hz.
1
2
3
800*600
1024*768
60
60
37.88
48.36
RESOLUTION
V.Freq.(Hz) H.Freq.(KHz)
1360*768
60
47.7
4
1280*768
60
47.3
PRESET MODE (HDMI)
1
2
3
800*600
1024*768
60
60
37.88
48.36
RESOLUTION
V.Freq.(Hz) H.Freq.(KHz)
1360*768
60
47.7
4
1280*768
60
47.3
5
1920*1080
60
67.5
5
1920*1080
60
67.5
(Only for 22"/40"/ 50"55")46"/
(Only for 19"/24"/28"/32")
VIDE O
L R
AV IN
VIDE O
L R
AV OUT
FOR 19"/22"/24"/28"
FOR 32"
FOR 40"/46"/50"/55"
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder,
video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i,1080P.
INSTALLATION
This TV provides one group of AV, one group of YPbPr for convenient connection to VCR, DVD
or other video equipment. Please refer to the owner's manual of the equipment to be connected
as well.
You can use the input terminals on TV set rear as follows.
AV Equipments for 19"/22"/24"/28"
-13-
Note:
1.VIDEO and YPbPr share one audio channel.
2.When HDMI port get DVI signal, the "PC Audio" channel is changed to receive the audio for HDMI port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT signal is AV;
other sources have no AV OUT signal.
W R
G
B
R
VIDEO EQUIPMENT with YPbPr
W
R
W
R
W R
TO AUDIO OUTPUTS
VIDEO EQUIPMENT
TO VIDEO
OUTPUTS
Y
Y
Red (audio R)
White(audio L)
R
Red(Pr or Cr)
W
R
Blue(Pb or Cb)
B
Green(Y)
G
Yellow (video)
Y
W
R
W R
TO AUDIO INPUTS
VIDEO EQUIPMENT
TO VIDEO
INPUTS
G B R
Y
HDMI
HDMI2 HDMI1USB
VGA
RF
Y Pb Pr
PC AUDIO
VIDE O
L R
AV IN
VIDE O
L R
AV OUT
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder,
video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i,1080P.
INSTALLATION
This TV provides one group of AV, one group of YPbPr for convenient connection to VCR, DVD
or other video equipment. Please refer to the owner's manual of the equipment to be connected
as well.
You can use the input terminals on TV set rear as follows.
AV Equipments for 32"
-14-
Note:
1.VIDEO and YPbPr share one audio channel.
2.When HDMI port get DVI signal, the "PC Audio" channel is changed to receive the audio for HDMI port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT signal is AV;
other sources have no AV OUT signal.
W R
G
B
R
VIDEO EQUIPMENT with YPbPr
W
R
W
R
W R
TO AUDIO OUTPUTS
VIDEO EQUIPMENT
TO VIDEO
OUTPUTS
Y
Y
Red (audio R)
White(audio L)
R
Red(Pr or Cr)
W
R
Blue(Pb or Cb)
B
Green(Y)
G
Yellow (video)
Y
W
R
W R
TO AUDIO INPUTS
VIDEO EQUIPMENT
TO VIDEO
INPUTS
G
B
R
Y
HDMI2
HDMI1
USB
VGA
Y
Pb
Pr
HEADPHONE
PC AUDIO
R F
HDMI
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder,
video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i,1080P.
INSTALLATION
This TV provides one group of AV, one group of YPbPr for convenient connection to VCR, DVD
or other video equipment. Please refer to the owner's manual of the equipment to be connected
as well.
You can use the input terminals on TV set rear as follows.
AV Equipments for 40"/ 50"/55"46"/
-15-
Note:
1.VIDEO and YPbPr share one audio channel.
2.When HDMI port get DVI signal, the "PC Audio" channel is changed to receive the audio for HDMI port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT signal is AV;
other sources have no AV OUT signal.
W R
G
B
R
VIDEO EQUIPMENT with YPbPr
W
R
W R
TO AUDIO OUTPUTS
VIDEO EQUIPMENT
TO VIDEO
OUTPUTS
Y
Y
Red (audio R)
White(audio L)
R
Red(Pr or Cr)
W
R
Blue(Pb or Cb)
B
Green(Y)
G
Yellow (video)
Y
W
R
W R
TO AUDIO INPUTS
VIDEO EQUIPMENT
TO VIDEO
INPUTS
Y
G
B
R
W
R
HDMI
AV OUTPUT
HDMI2 HDMI1 USB R FVGAPC AUDIOVIDEO L R
REMOTE CONTROLLER
-16-
Standard, Mild, User,
Dynamic.
Standare Music Movie, , ,
Sports User.,
Auto, 4:3, 16:9, Zoom, Panorama.
Press CH+ or CH- to go to the next or previous channel.
In USB mode, used as Play/Pause key.
In USB mode, used as Stop key.
In USB mode, used as Previous key.
In USB mode, used as reverse key.
In USB mode, used as forword key.
In USB mode, used as Next key.
Favorite program hotkey .
Favorite program hotkey .
Favorite program hotkey .
Favorite program hotkey .
RETURN
REPEAT
Under USB channel, switch to play mode.
Under different channels, optional scaling mode is different.
High, Mid, Low.
OFF, Audio Only,
,
Use this key to return to main multimedia menu while
playing a track/item.
Under HDMI channel, when "HDMI CEC" function set as"open", PLAY/PAUSE STOP PREV NEXT
FF FR will play function accordingly.
、 、 、 、
GUIDE
、
When playing the multimedia file, press [GUIDE] key. The task bar
will show for guiding the Multimedia. Under HDMI channel, when
"HDMI CEC" function set as"open" used as "ROOT MENU" key.,
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Videocon VKC19HH Owner's manual
- Category
- LCD TVs
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Haier LE24T1000F Owner's manual
-
Haier LE32K6000 Owner's manual
-
JIECANG JCHR35W1C User manual
-
-
Philips 29PFL4938/V7 User manual
-
Philips 40PFL4958 User manual
-
Soundmaster DISC4020 Datasheet
-
Sharp LC-70LE734U User manual
-
-
