Aidapt VP180 Assembly And Maintenance Instructions

Brand: Aidapt

Model: VP180

Type: Assembly And Maintenance Instructions

Medium Lightweight Walking Frames

Assembly and Maintenance Instructions

Fig. 1

Notes for the User

Always consult with the prescriber/Physiotherapist if you are in any doubt that this

product is suitable for your use.

When the frame is adjusted correctly the user should be able to maintain an upright

posture with the elbow slightly flexed. In this way, body weight is taken through the frame

by pushing down on the frame when walking.

N.B. This equipment must be

assembled by a competent person.

VP180/VP181Medium Lightweight Walking

Frame

101 kg (16 st.) weight limit.

Do not exceed the weight limit stated

– doing so could put the user at risk.

1. Introduction

Thank you for deciding to purchase the Medium Lightweight Walking Frame from Aidapt. The Walking

Frame is manufactured from the finest materials and components available, when assembled and

used correctly it is designed to give many years of reliable trouble-free service.

2. Before Use

Please examine your Walking Frame for any visible damage before use. If you see any damage or

suspect a fault, please do not use the product, but contact your supplier immediately for support.

Your walking frame is delivered unassembled and we would strongly advise that your

retailer/technician assembles this for you.

3. How to Assemble the Walking Frame

3.1. Firstly check that every component is with the product (see Fig. 1).

3.2. Fit the saddle clips in the open ends of the tubing that on the “U” shaped horizontal cross bar.

3.3. Rest the saddle clips against the back legs and fasten in place with two bolts loosely.

3.4. Slide the two bolts through the holes in the front legs and slide on the double sided saddle

clips ensuring that they are the right way round and fit the tubing.

3.5. Push the bolts that are through the front legs on through the horizontal cross bar and use the

locking nuts to secure loosely.

3.6. Line the two holes at the top of the frame with the two holes that are on the tubing

underneath and insert the bolts provided, use the locking nuts provided to secure the bolts.

3.8. Tighten all the nuts and bolts up completely

3.9. Check all joints, nuts and bolts to ensure the frame is completely secure.

09/11/10

1573

Medium Lightweight Walking Frames

Assembly and Maintenance Instructions

4. Warning

For safety, these precautions must be taken when using these products.

• Walker sits level and all legs are adjusted to the same height.

• Ferrules are in good condition - replace if necessary.

• Do not exceed the maximum weight limit for the frame (100 kg).

• Use only Aidapt parts or accessories.

• When using accessories such as bags, baskets, etc., ensure these are fitted safely and are

not overloaded.

• Stow the frame with care when transporting in a car boot. Damage can occur due to

impact with car boot door.

5. Getting into and out of Chairs

1. Position the frame in front of the chair.

2. Get up by pushing on the arms of the chair and transfer hand to frame when fully

standing.

3. To sit down, using the frame, turn round in front of the chair and feel using wheeled

frames, the rear legs of the chair behind you with your legs.

4. Place hands gently on the chair arms, bend slightly forward and sit down gently

6. General Safety

• Use a chair with high seat and arms to help you sit and stand up with ease.

• Remove obstacles such as loose rugs, draught excluders and worn floor coverings.

• Ensure lighting in hallways and stairways is adequate.

• Wear flat, supportive shoes.

• Avoid wet floors.

• Beware of outdoor hazards including uneven surfaces, wet leaves and ice.

• Do not store this product in temperatures below freezing.

• Take special care if carrying a bag or similar package.

7. Check For:

• Bent or damaged tubes or cracks at the tube joints.

• Loose or worn horseshoe clips

• Elongated adjustment holes.

• Loose handles.

• Loose or worn Wheels and wheel fasteners (where fitted)

• Smooth, worn or split ferrules (rubber tips).

• Replace all worn, missing or damaged parts where necessary.

8. Cleaning

Regular cleaning with a mild disinfectant is recommended. DO NOT use bleach or any

solvents (such as lighter fluid).

9. Reissue

If you reissue or are about to reissue this product, please thoroughly check all

components for their safety, this includes:

• Bent or damaged tubes or cracks at the tube joints.

• Loose or worn horseshoe clips

• Elongated adjustment holes.

• Loose handles.

• Loose or worn Wheels and wheel fasteners (where fitted)

• Smooth, worn or split ferrules (rubber tips).

Replace all worn, missing or damaged parts where necessary. If in any doubt, please do

not issue or use, but immediately contact your supplier for service support.

10. Important Information

The information given in this instruction booklet must not be taken as forming part of or

establishing any contractual or other commitment by Aidapt Bathrooms Limited or

Aidapt (Wales) Ltd or its agents or its subsidiaries and no warranty or representation

concerning the information is given.

Please exercise common sense and do not take any unnecessary risks when using this

product; as the user you must accept liability for safety when using the product.

11. Maintenance

Please make a safety check of the product at regular intervals or if you have any

concerns.

Aidapt VP180 Assembly And Maintenance Instructions

Aidapt VP180 Assembly And Maintenance Instructions

Aidapt VP180 Assembly And Maintenance Instructions

Related papers

Other documents