Texas Rider 6110E Owner's manual

Rider 6100E - Rider 6110E

Texas A/S - Knullen 22 - DK-5260 Odense S - Denmark Version 19.1

Tel. +45 6395 5555 - www.texas.dk - [email protected]

DK

GB

DE

Betjeningsvejledning

User manual

VIGTIGT !

HUSK AT PÅFYLDE MOTOROLIE

SAE-30

FØR START!

IMPORTANT !

REMEMBER TO FILL WITH ENGINE OIL

SAE-30

BEFORE START!

ACHTUNG !

DENKEN SIE DARAN, VOR

INBETRIEBNAHME MOTORÖL (SAE-30)

AUFZUFÜLLEN!

2

Advarselssymboler / Warning symbols / Warnsymbole

Advarselssymboler

Warning symbols

Warnsymbole

DK

GB

DE

Læs

betjeningsvejledningen før

maskinen benyttes.

Read the user manual

before

operating this machine.

Bitte lesen Sie das

Benutzerhandbuch

aufmerksam durch, bevor

Sie den Maschinen in

Betrieb nehmen.

Fare for flyvende objekter.

Hold afstand til mennesker

og dyr.

Danger for ejected

objects. Keep bystanders

away

Gefahr für ausgeworfene

Gegenstände Halten Sie

die Zuschauer weg

Hold køreområdet fri for

især børn og dyr.

Make sure the area is free

of especially children and

animals.

Lassen Sie niemals Kinder

oder mit diesen

Anweisungen nicht

vertraute Personen die

Maschine benutzen.

Hinweis: Lokale

Vorschriften können das

Alter des Bedieners

einschränken.

Fjern startnøglen og læs

instruktionerne før nogen

form for vedligeholdelse

eller reparation udføres.

Remove the start key and

read the instructions

before carrying out any

maintenance or repairs

Entfernen Sie die

Starttaste und lesen Sie

die Anweisungen, bevor

Sie Wartungs- oder

Reparaturarbeiten

durchführen

Afmonter tændrørshætten

og læs instruktionerne før

nogen form for

vedligeholdelse eller

reparation udføres.

Disconnect the spark plug

cap and read the

instructions before

carrying out any

maintenance or repairs

Ziehen Sie den

Zündkerzenstecker ab und

lesen Sie die

Anweisungen, bevor Sie

Wartungs- oder

Reparaturarbeiten

durchführen

Kør ikke på stigninger over

10 grader.

Do not use the machine

on slopes greater than 10

degrees

Benutzen Sie das Gerät

nicht auf Hängen größer

als 10 Grad

Kun Rider 6100E:

Kør aldrig uden

opsamlerkassen monteret.

Only Rider 6100E:

Never operate the

machine without the

collector catcher

attached.

Nur Rider 6100E:

Niemals die Maschine

betreiben, ohne dass der

Kollektorfänger befestigt

ist.

Put aldrig hænder eller

fødder under klippeskjoldet,

når maskinen kører.

Do not put hands or feet

near or under the cutting

deck when machine is

running.

Bringen Sie niemals

Hände oder Füße in die

Nähe von rotierenden

Teilen oder darunter.

Roterende knive. Hold

hænder væk, da risiko for

personskade.

Rotating blade. Keep

fingers away, as there is

risk of injury.

Achten Sie auf rotierende

Messer!

Page is loading ...

17 
 
GB Original instructions 
 
Warning symbols .......................................................... 2 
Illustrations ................................................................... 3 
Safety ......................................................................... 17 
Identification of the parts ............................................ 18 
Mounting .................................................................... 18 
Tyre pressure ............................................................. 18 
Battery (Electric starter).............................................. 18 
Operation ................................................................... 19 
Blade .......................................................................... 19 
Water nozzle .............................................................. 19 
Oil change .................................................................. 20 
Air Filter ...................................................................... 20 
Spark plug .................................................................. 20 
Storage and maintenance .......................................... 20 
Warranty terms and conditions ................................... 21 
Troubleshooting ......................................................... 29 
CE Declaration of conformity ...................................... 31 
 
Safety 
 
Setup 
  Do not put hands or feet near or under rotating 
  parts. 
  Read this manual carefully. Make sure that you are 
familiar with the different controls, settings and 
handles of the equipment. 
  Know how to stop the unit and ensure that you are 
familiar with emergency stop. 
  Never allow children or people unfamiliar with 
these instructions to use the machine. Note, that 
local regulations can restrict the age of the 
operator. 
  If you feel unwell, tired or have consumed alcohol 
or drugs, do not operate the machine. 
  Always inspect the machine before usage Ensure 
that no parts are worn or damaged. 
  Replace worn out or damaged elements and bolts 
in sets to preserve balance. 
  The operator of the machine is responsible for 
people’s safety. 
  Never use the machine near children or animals. 
  The operator of the machine is held liable for any 
accidents or hazards to other people and their 
property. 
  Thoroughly inspect the area, where the equipment 
is to be used, if necessary remove any  foreign 
objects. 
  Do not refuel gasoline indoors or while the engine 
is running. 
  Spilled gasoline is extremely flammable, never 
refuel while the engine is still hot. 
  Wipe off any spilled gasoline before starting the 
engine. Spilled gasoline on a hot engine may 
cause a fire or explosion! 
  Boots with non-slip soles with steel jacket is 
required. Avoid loose-fitting clothes. 
 
Operation 
  After striking a foreign object, stop the engine 
immediately, remove the spark plug cap and 
inspect the machine thoroughly for damage. Repair 
the damage before continuing. 
  If the machine should start to vibrate abnormally, 
stop the engine and check immediately for the 
cause. Vibration is generally a warning of damage. 
  Always turn off the engine and ensure that all 
moving parts have come to a complete stop 
 
  before making any repairs, adjustments, or 
inspections. 
  Exercise extreme caution when operating on 
slopes. 
  Never operate the machine at a fast pace. Do not 
overload machine capacity by attempting to push at 
too fast a rate. 
  Do not carry passengers. 
  Never allow any bystanders in front of unit. Only 
operate the machine at daylight or in fully 
illuminated areas. 
  Ensure a stable foothold and always keep a firm 
hold on the handles. Always walk, never run. 
  Do not operate the machine when barefoot or 
wearing sandals. 
  Exercise extreme caution when changing direction 
on slopes 
  Never attempt to make any adjustments, while the 
engine is running. 
  Use extreme caution when reversing or pulling the 
machine backwards 
  Never operate the engine indoor or in areas with 
low ventilation. The exhaustion from the engine 
contains carbon monoxide. Failure to observe 
could result in permanent injury or death. 
 
Gasoline safety 
  Use extreme care in handling gasoline. Gasoline is 
extremely flammable and the fumes are 
explosive.Serious personal injury can occur, when 
gasoline is spilled on yourself or your clothes. 
Rinse your skin and change clothes immediately! 
  Use only an approved gasoline container. Do not 
use soft drink bottle or similar! 
  Extinguish all cigarettes, cigars, pipes and other 
sources of ignition. 
  Never refuel your machine indoors. 
  Let the engine cool down before refilling Never fill 
the fuel tank to more than 2.5 cm below filler in 
order to provide space for fuel to expansion. 
  After refueling, ensure that the cap tighten 
securely. 
  Never use the lock-function on the gasoline gun, 
when refueling. 
  Do not smoke while refueling. 
  Never refuel gasoline inside a building or where 
gasoline fumes may get in contact with an ignition 
source. 
  Keep gasoline and engine away from appliance, 
pilot lights, barbecues, electric appliances, power 
tools, etc. 
 
Maintenance and storage 
  The engine shall be stopped when carrying out 
maintenance and cleaning operations, when 
changing tools and when being transported by 
means other than under its own power. 
  Check regularly that all bolts and nuts are 
tightened. Retighten if necessary. 
  The engine must be completely cooled before 
storing indoors or covered. 
  If the machine unused for a period of time, please 
refer to the instructions in this manual. 
  Maintain or replace safety and instruction labels, as 
necessary. 
  Only use orginal spare parts or accessories. If not 
orginal parts or accessories is used, the liablility is 
no longer applied. 
 
 

18

Miscellaneous

The motor is not pre-filled with oil.

Always before start check the engine oil level.

Factory-fitted control devices, such as the handle-

mounted clutch cable, must not be removed or

exposed.

Only drain the fuel tank outdoors. Gasoline is

extremely flammable and the fumes are explosive.

Ensure that the machine is properly secured when

transported on a flatbed etc.

Waste electrical products must not be

disposed of with the household waste. This

tool should be taken to your local recycling

centre for safe treatment.

The rider is manufactured according to the latest safety

requirements. These include a blade brake that stops

the motor and blade in 3 seconds when the blade

brake. Every precaution is only effective when it is

followed exactly. Use the following description when

you mount your rider.

Identification of the parts

See Illustration 1+3

Notice: the illustrations may vary from your present

model

A. Choke.

B. Gear.

C. Ignition key - Electric starter.

D. Water nozzle.

E. Height adjustment. (cutting deck)

F. Brake/clutch pedal

G. Parking brake.

H. Coupling rod. (for blade)

I. Safety switch.

J. Grass collector

K. V-belt

L. Recoil

M. Oil tank

N. Fuel tank

O. Air filter

Mounting

Unpacking: Illustration 5-9

Remove the Rider from the box by following the

description below. The box contains:

1 pcs. Rider

1 pcs. Steering wheel.

1 pcs. Battery Charger

1 pcs. Coupling rod

1 pcs. Seat

1 pcs. Bolt bag (See ill.9 a-l)

1 pcs. Grass collector

The easiest way to unpack:

1.

Remove upper frame. If necessary, use a hammer

to remove it from main frame. Get somebody to

hold the end of the frame you can´t reach yourself.

See ill.7

2.

Remove the two brackets holding the front wheel

and the rear wheel to the frame. ill. 7-8 (Arrows in

the picture)

3.

Remove the rider from the box by pulling the

machine out form the side. It can be an advantage

to be 2 people for this.

Technical installation

Note: To lift the cover, it is necessary to remove all the

black / silver gray handles. (ill.13)

1.

Lift the cover (ill.13)

2.

Add oil (ill.16) and unleaded 95 octane gasoline

(ill.17)

3.

Cennect the wire to the battery (ill.14)

4.

Ensure that the safety switch under seat (ill.2) and

on rear plate is activated.

5.

Put cover and handles back in place

Assembly instructions

1. Mount the coupling rod for the cutting deck as

shown. (ill.11)

2. Open the seat flap, fit and install the seat as

shown. (ill.10)

3. Mount the steering wheel to steer axle, use a

hammer to knock the pin into the shaft (ill.12)

4. Mount the grasscollector and attach to rider as

shown in ill. 19

5. It is recommended to mount the safety bolt and pin

as shown in ill.18 This fix the cover to the chassis

of the machine.

Tyre pressure

Check tyre pressure before start.

The correct tyre pressure is 2.1 bar (31 psi) on all

wheels.

Important: When tyre pressure is too low the valves and

the inner tube may be damaged.

Battery (Electric starter)

Charge the battery before use

Before the electric start function is used, the battery

must be charged for 5 hours. Put the charger plug into

the hole in the battery and connect the charger to a

power supply. Ill.15

Charging during the season

The battery is charged a little during use, buy it will

likely be necessary to charge the battery a couple of

times during the season - depending if the number of

start/stops of the engine. Put it for charging for around 5

hours.

Storage of battery

The battery must always be stored dry and warm during

the winter. Never expose it for low temperatures.

Charge the battery completely before storing and then

place the lawn rider in a place where it is not exposed

to frost. Alternatively cover the battery with a thick

carpet or similar, If the rider is in a shed/garage where

there may be cold.

Charge the battery 1-2 times during the winter (at least

every 3

rd

month) to make sure the battery keeps it full

capacity.

Incorrect storage can damage the battery and is not

covered by warranty.

19

Operation

Always check and refill oil before the start!

The oil level should always be between min. and max

on the dipstick. Fill with SAE-30 oil follow instrucktion I

engine manual. Use only unleaded 95 octane fuel to the

engine. Never overfill the tank. (ill.16-17)

Activation of P-brake: ill.20.5

To activate the P-brake, the clutch / brake must be fully

depressed and then the P-brake can be activated.

Cutting height adjustment: ill.20.3

The rider has 5 different heights. The cutting height

ranges from 35 mm to 75 mm

Start

Never start the rider directly on long grass!

The blade must always be switched off during the start

procedure. This applies both to electric start and start

with recoil starter.

Electrical starter: ill.20

1. Move the gear lever to position N. ill.20.2 (You will

need to sit on the rider before you can use the

electrical start.)

2. By cold engine set the choke lever on ”Choke” ill

20.1 By warm engine set the choke lever on ”Run”

3. Set the height adjustment to the highest position. ill

20.3

4. Press the foot pedal fully. ill.20.5(1)

5. Turn the engine key to start and release key when

the engine is started. ill.20.6

6. Return the choke lever in the ”run” position. (only

cold engine). ill 20.1

7. Set speed lever in gear from 1 to 4 (or reverse “R”)

ill.20.2

8. Disable the P-brake. ill.20.5(2)

9. Activate the blade ill.20.4 and release the foot

pedal. ill.20.5(1)

Blade activation: ill 20.4

When the blade is to be activated, the coupling rod

must be activated slowly.

The coupling rod must be slid forwards to the left, then

pulled straight to the right and into the notch.

This locks the rod firmly and the blade is activated.

To stop the knife, the same movement is done just the

opposite.

Recoil with choke, speed lever

Move the gear lever to postion N (ill.20.2) and activate

P-brake. See the section: Activation of P-brake.

Remove the handels so the cover can be tilted up.

By cold engine set the choke lever on ”Choke”

By warm engine set the choke lever on ”Run”.

Turn the engine key to on. Pull the recoil starter gently

until you feel resistance in the rope, then pull quickly

and energetic. Do not at any time let go of the recoil

starter but slide it gently into starting position and return

the choke lever in the ”run” position (only cold engine).

Set speed lever in gear from 1 to 4 (R)

Release the hand brake

Activate the blade and release the foot pedal.

Regulation of speed

Speed can be adjusted from 1.5 – 4.6 km/h while

driving. Activate the right handle on the dashboard and

set in one of the 4 different speeds or reverse. When

driving in one the two lowest speeds the pace

difference will not vary significantly.

Stop: ill 20.6

Turn the ignition key to the off position.

Note: The blade will still rotate at up to 3 seconds after

stopping.

Blade

Inspection of the blade

1. Tilt the rider with the back upwards.

2. Inspect blade for damage, cracks or excessive rust

or corrosion.

3. Check that the blade bolt is tightened.

Note: A dull blade can be sharpened! But a blade that

is worn, bent, cracked or otherwise damaged must be

replaced.

Removing the blade:

If you remove the blade to sharpen or replace it, you

must use a torque wrench and some heavy gloves to

protect your hands.

1. Loosen the blade bolt. Use a piece of wood to

prevent the blade from turning around.

2. Remove the bolt, washer, blade and blade holder

in that order

3. Sharpen or replace the blade.

4. Insert the blade holder, blade, washer and bolt in

that order.

5. Tighten the blade bolt. Use a piece of wood to

prevent the blade from turning around.

Warning: A blade must be sharpened so it is in

100 % balance, otherwise it may cause vibrations that

could damage the engine. Damage to engine due to

faulty sharpening is not covered by warranty. We

therefore recommend letting a service center sharpen

the blade.

Water nozzle

The left side of the rider deck is fitted with a water

nozzle for washing the deck. ill.4

1. When using the water nozzle, the machine must be

in the lowest height position and placed on the

lawn. This ensures that the water remains under

the deck during cleaning.

2. Attach a hose to the nozzle.

3. Turn on the water and start the engine.

4. The rotations of the blade will ensure that the water

will clean the underside of the deck.

If above instruction is not followed, water may

splash back on the gearbox and clutch cable,

which increases the risk of corrosion and damage

to both parts. This will not be covered by the

warranty!

Note: For best result clean the deck with the water

nozzle function right after each mowing. If the grass

dries out, this function will not work optimally.

20

Oil change

Oil should be changed for the first time after 2 hours,

then at least 1 time per year.

You will need an oil extractor kit. Art. no. 40-11336

Oil and oil extractor kit is not included

Use an extractor kit and do as follows:

1. Turn on the engine and let it run for 5 min or until

the engine is hot. A hot engine liquefies the oil

which makes it easier to drain.

2. Suck the oil up through the oil filler hole using the

syringe that came with the oil extractor kit. Use the

hose to reach the sump.

3. Transfer the used oil into a empty container.

4. Fill the engine with SAE-30 oil.

5. Check the oil level using the dipstick. (Min / Max)

Remember to dispose the used oil so that it does

no harm to nature. Use your local recycling station.

Air Filter

The air filter should be inspected and cleaned regularly.

If the filter has not been cleaned for a long time, the

engine’s power will drop.

1. Clean around the air filter before removing the cap.

2. Push the two flaps down and gently pull the cover

3. Carefully remove the paper filter and inspect it.

Brush it with a soft brush. If it is very dirty, replace

it. Be careful that no dirt gets into the inlet.

4. Wash the black foam element in the right side in

warm water and soap.

5. Press the water out of the foam element and let it

dry. Put a few drops of SAE-30 oil on the filter to

moisten it lightly. Carefully squeeze any surplus oil

out of the foam element and reattach.

6. Please note that all parts are assembled correctly

and properly closed, as shown in the picture.

Spark plug

1. Remove the spark plug.

2. Brush off dirt from the spark plug.

3. Use a spark plug wrench to loosen the spark

plug.

4. Check the insulation is intact.

5. Clean the spark plug with a wire brush.

6. Measure the electrode, taking care not to

damage the electrode.

7. The distance should be: 0.7 to 0.8 mm

8. If the spark plug is undamaged refit or replace.

9. Reattach the spark plug.

Storage and maintenance

Maintain your rider: Check all bolts, screws, nuts and

deck. Dismount the blade and the belt plastic cover for

regular cleaning. Always make sure that the blade is

sharp. It’s a good idea to take your lawn rider to an

annual service check with your authorized service

dealer. See your nearest service center at

www.texas.dk.

Storage: After use the rider kept in a dry and clean

room. Clean the machine after every use. Grass and

dirt must be removed from the underside of the deck.

By tipping the rider (for cleaning) is recommended to tilt

the front up (max. 45 degrees). If you tilt it sideways,

the carburetor and air filter always face upwards, since

oil may run out and destroy the engine. Be aware that

removing the spark plug before the rider maintenance.

Winter storage: Empty the fuel tank and let the engine

run until the gasoline in the carburetor is used up. Spark

plug removed. Remove the spark plug and add a

teaspoon of oil (engine oil) in the hole. Pull the starter to

distribute oil. Mount the spark plug, but not the spark

plug cap. Change oil as described in the section above.

Spray silicone lubrication into the cables and move

them.

Finally, clean the rider thoroughly. Dip a cloth in oil and

luricate metal parts to prevent rust.

Towbar

The machine is fitted with a towbar.

Only a small trailer may be mounted after the rider. (no

other retrofitted accessories).

The maximum load on the trailer is 25 kg, which means

less cargo such as grass, branches and leaves.

If the towbar is used for larger loads or other

accessories than the carriage, the warranty does not

cover.

21

Warranty terms and conditions

The warranty period is 2 years for private end users in

EU countries.

Products sold for commercial use, only have a warranty

period of 1 year.

The warranty covers material and/or fabrication faults.

Restrictions and requirements

Normal wear and replacement of wearing parts are

NOT covered by the warranty.

Wearing parts, which are NOT covered for more than

12 months:

• Blade

• Cables

• Belts

• Fuses

• Switches

• Membranes/gaskets

• Spark plugs

• Engine liquids (oil, gasoline)

• Starter cords

• Filters

• Battery: If the battery is not stored correct (frost-

free and recharged every 3 months), the durability

is only guaranteed for 6 months.

If you start the engine without adding oil, it will be

damaged and cannot be repaired and therefore not

covered by the warranty.

The warranty does NOT cover damages/faults

caused by:

• Lack of service and maintenance

• Structural changes

• Exposure to unusual external conditions

• Damages to the bodywork, deck, handles, panels

etc.

• If the machine has been improperly used or

overloaded

• Wrong use of oil, gasoline or other liquid types,

which are not recommended in this user manual

• Bad or dirty gasoline, which results in

contamination of the fuel system

• Use of unoriginal spare parts.

• Other conditions where Texas cannot be held

responsible.

Whether a case is a warranty claim or not is

determined in each case by an authorized service

center.

Your receipt is your warranty note, why it should

always be kept safe.

REMEMBER: The purchase of spare parts as well as

any request for warranty repair, art. number (e.g.

9006XXXX), year and serial number should always be

informed. It can be found on the CE-label located on

the rearpart of the cutting deck behind the engine!

* We reserve the right to change the conditions and

accept no liability for any misprints

Technical data

Model

Rider 6100E / 6110E

Engine model

Loncin - LC1P70FAD

Self-drive speed

1.5 - 4.6 km/t

Reverse-drive

2,3 km/t

Engine displacement

196 cc

Nominal power

4,8 kW

Cutting width

61 cm

Max.Engine speed

3000 /min

Fuel tank capacity

1,2 L

Height adjustment

35-75 mm, 5 positions

Net weight

115 kg

Grass collector

150 L

LPA

83,0 dB(A)

LWA

98 dB(A)

Vibration (body / hand)

1.691 / 2.069 m/s

2

Page is loading ...

29

Troubleshooting

If your problem is not described above, please contact an approved service centre or Texas A/S.

Difficult to start

Problem

Cause

Solution

Generally difficult to start

• Wrong starting procedure

• Follow the starting instructions in the

manual precisely.

The machine will not start

when the start cord is pulled or

the electric start button is

pushed

(or the starter "clicks" when

attempting an electric start)

• The safety switches is not being

activated

• The wires are not connected to

battery The brake cable is

incorrectly adjusted

• The machine is standing in high

grass

• Engine brake cable is too loose

• The choke is not in the correct

position

• No more gasoline in fuel tank

• The gasoline is more than 3

months old

• Connection plug filled with grass

• Activate safety switches under the seat

and collectorbag (only Rider 6100E).

• Check that the wires are connected from

the battery to the motor and start button.

• Move the machine away from the high

grass to start it.

Set the height adjustment in the highest

position, so that the blade can run freely.

• Move the choke lever to a different

position.

• Check and fill fuel tank with gasoline.

• Empty the fuel tank and carburettor from

old gasoline, and fill with new gasoline.

• Remove grass from and around the

connection plug

No ignition spark (cannot start)

• The spark plug cap is loose

• The spark plug is damp or dirty

• Incorrect gap between the spark

plug and the electrode

• The air filter is dirty or defective

• Check that the cap is firmly attached to the

spark plug.

• Check that there is no dirt on the spark

plug, following the instructions in the

manual.

• Check and adjust the spark plug gap,

following the instructions in the manual.

Alternatively, replace the spark plug.

• Check the air filter for dirt and clean it,

following the instructions in the manual.

The rider starts, but runs unevenly

Problem

Cause

Solution

Insufficient engine revolutions

• Lever is in the "Choke" position

• The throttle lever is set for

"Turtle "

• Set the lever in the "Run" position.

• Set the throttle lever for "Rabbit".

The back wheels are not

pulling, or only very little

• The belt is torn or has fallen off

• Gearbox defect

• Replace belt

• Replace thegearbox

The engine runs irregularly

and/or its performance

becomes poor as you are

working

• The spark plug cap is loose

• The spark plug is dirty

• Incorrect gap between the spark

plug and the electrode

• The air filter is dirty or defective

• Evaporation of fuel in the

carburettor

• Loose throttle cable

• Dirt in the carburettor

• Check that the cap is firmly attached to the

spark plug.

• Check that the spark plug is clean and not

damaged, following the instructions in the

manual.

• Check and adjust the spark plug gap,

following the instructions in the manual.

• Check the air filter for dirt and clean it,

following the instructions in the manual.

• Wait a few minutes, and then try to start

again.

• Tighten the throttle cable, following the

instructions in the manual.

• Clean the carburettor.

The engine will not stop

Problem

Cause

Solution

The machine does not stop

after 5 seconds

• The engine brake cable runs too

tightly

• Check and adjust the engine brake cable,

following the instructions in the manual.

Page is loading ...

31

CE Overensstemmelseserklæring

DK

CE Declaration of conformity

GB

CE-Konformitätserklärung

DE

Producent • Manufacturer • Hersteller

Texas Andreas Petersen A/S

Erklærer herved at materiel • Hereby certifies that the following • Bescheinigt hiermit das die

nachfolgenden

Rider • Lawn rider • Rasenmäher

Rider 6100ES - Rider 6100E

Er fremstillet i overensstemmelse med følgende direktiver • Is in compliance with the specifications of

the machine directive and subsequent modifications • Steht im Einklang mit den folgenden Richtlinien

2006/42/EC - 2004/108/EC

Overensstemmelsesvurdering procedure i henhold til bilag III/VI • Conformity assessment procedure

according to Annex III/VI • Konformitätsbewertungsverfahren nach Anhang III/VI

2000/14/EC amended by 2005/88/EC

Materiellet er udført i overensstemmelse med følgende standarder • Conforms with the following

standards • In Übereinstimmung mit den folgende Standards

EN 836:1997+A4, EN ISO 5395-1:2013, EN ISO 14982:2009

ZEK 01.4-08/11.11, AfPS GS 2014:01

Measured L

pA

: 83.0 dB(A)

Guaranteed L

wA

: 98 dB(A)

Vibrations (body / hand):

a

h

= 1.691 / 2.069 m/s

2

Serial numbers:

Rider 6100E: 1901410001 - 2112419999

Rider 6110E: 1901400001 - 2112409999

Texas Andreas Petersen A/S Responsible for documentation

Knullen 22 • DK-5260 Odense S Johnny Lolk

07.02.2019

Johnny Lolk

Managing Director

Page is loading ...

Texas Rider 6110E Owner's manual

This manual is also suitable for

Texas Rider 6110E Owner's manual

in other languages

Related papers

Other documents