Contec PC-HDD40G Owner's manual

Brand: Contec

Model: PC-HDD40G

Type: Owner's manual

PC-HDD40G

2.5-inch 40GB PATA Hard Disk Drive

PC-HDD40G User’s Guide

CONTEC CO.,LTD.

Thank you for purchasing the CONTEC PC-HDD40G. Please use this product in accordance with the

procedures described in this document.

Product Configuration

- Hard Disk Drive……1

- Screw (M3x5, with sw, w) ……4

- Insulation Film……1

- Jumper……1

Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

Safety Information

This document provides safety information using the following symbols to prevent accidents resulting in

injury or death and the destruction of equipment and resources. Understand the meanings of these labels

to operate the equipment safely.

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury or in property damage.

Disclaimers

We shall not be liable for any consequential damages such as losses and lost profits resulting from the

operation of this product. For any reason we shall provide no warranty for the stored contents on your

hard disk.

PC-HDD40G User’s Guide

PC-HDD40G

Handling Precautions

CAUTION

- Do not apply pressing force on the top of cover.

- Do not cover the breathing hole on the top cover.

- The system is responsible for providing sufficient air movement to maintain surface temperatures

below 82°C on the top cover

- Do not touch the interface connector pins and the surface of printed circuit board.

- Hard disk is precision instruments. Be extremely careful in handling during and after assembly.

- Hard disk can malfunction when it is subjected to electrostatic discharge (ESD) or physical shock.

Handle with care so that antistatic measures are taken in advance and do avoid shock.

- Be sure to turn off the power of the unit when plugging in or unplugging interface connectors.

- Use the mounting screws (M3x5 with sw, w : for screwing the base) provided with the product.

Longer screws may damage the interior of the product.

- CONTEC bears absolutely no responsibility for use if modified hard disk.

- Excessive vibration or impact greater than its specification, if this hard disk is subjected to, might

cause a fatal error that is not recoverable.

- Service life of the drive is approximately 5 years or 15,000 power on hours, whichever comes first.

These are the standard values when the environmental and operational conditions specified in page 3

are observed and are not the guaranteed values.

Unaccommodated host PCs

You can not use this drive when if you use these host PCs.

IPC-PT/M30(PC), IPC-PE/M30(PC), IPC-PS/M30(PC),

IPC-PL/M30(PC), IPC-BX/M20(PC), IPC-BX/M10(PC), PC-386(PC), PC-386(PC)S, PC-486M(PC),

IPC-PT/M140(PC), IPC-PS/M140(PC), IPC-PT/M100(PC), IPC-PS/M100(PC), PC-IDE/FD(98)A,

PC-486M(PC)H, IPC-PT/M340(PC)H, IPC-PT/M500(PC),

IPC-PT/M500S(PC), IPC-PT/M530(PC), IPC-PT/M530S(PC),

IPC-TT/M300(PC), IPC-TT/M310(PC), IPC-TT/M340(PC),

IPC-TT/M340S(PC), IPC-TT/M500(PC), IPC-TT/M500S(PC),

IPC-PT/M140(PC), IPC-PT/M140(PC)H, IPC-BX/M400(PC),

IPC-BX/M400(PC)H, IPC-BX/P400(PC)

PC-HDD40G User’s Guide

PC-HDD40G

Specification

Item Specification

Total recording capacity

40GByte

Host interface ATA/ATAPI-6 (up to 100MB/s)

Max. 514Mbit/sec Transfer velocity

(Gbps)

Typ. 461Mbit/sec

Input voltage +5VDC (±5%)

Sleep 0.10W (typ.)

Read / Write / Seek 2.15W / 2.15W / 2.4W(typ.)

Consumed power

Startup *1 6.5W (Max.)

Environment

Temperature

-20 - 75°C

Humidity 5 - 90%RH (With no condensation)

Maximum wet bulb

temperature

40°C (With no condensation)

Temperature change

gradient

120°C/h or less for up

60°C/h or less for down

(With no condensation from temperature gradient)

Altitude 1025hPa - 701.1hPa (Above the sea -300 - 3000m)

Swept sine vibration 3.0G or less (10 - 50Hz)

2.5G or less (50 - 200Hz)

1.0G or less (200 - 500Hz)

Operating

Shock 250G or less (2ms)

100G or less (11ms)

Temperature -40 - 95°C

Humidity

5 - 95%RH (With no condensation)

Maximum wet bulb

temperature

40°C (With no condensation)

Temperature change

gradient

120°C/h or less for up

60°C/h or less for down

(With no condensation from temperature gradient)

Altitude 1025hPa - 120.4hPa (Above the sea -300 - 15000m)

Swept sine vibration 5.0G or less (10 - 500 - 10Hz)

Non-operating

Shock 800G or less (1ms)

Power on hours 250 hours/month or less Operational

condition

Read / Write / Seek 20% or less at power on hours (maximum 3,000 hours)

MTBF 550,000H

Weight 97g (Max.)

*1 Maximum power consumption at motor startup

Fixed disk characteristics

Description Logical Layout

Bytes per

Sector

Sectors

per Track

Number

of Heads

Number

of Disks

Number

of Heads

Number of

Sectors/

Track

Number of

Cylinders

Number of

Sectors

Total Logical Data

Bytes

PC-HDD80S 512 576-1320 2 1 16 63 16,383 78,140,160 40,007,761,920

PC-HDD40G User’s Guide

PC-HDD40G

Physical Dimensions

Master/Slave Settings

Master Setting

(Open : Default Setting)

Slave Setting

A-B Short

Note!

Never attach a jumper to settings which are not shown above.

PC-HDD40G User’s Guide

PC-HDD40G

Installation

HDD

Insulation Film

Installation Part

Screw (with sw,w)

Connector Pin Assignment

Pin Signal I/O Type Pin Signal I/O Type

1 RESET- I TTL 2 GND

3 DD07 I/O 3-state 4 DD08 I/O 3-state

5 DD06 I/O 3-state 6 DD09 I/O 3-state

7 DD05 I/O 3-state 8 DD10 I/O 3-state

9 DD04 I/O 3-state 10 DD11 I/O 3-state

11 DD03 I/O 3-state 12 DD12 I/O 3-state

13 DD02 I/O 3-state 14 DD13 I/O 3-state

15 DD01 I/O 3-state 16 DD14 I/O 3-state

17 DD00 I/O 3-state 18 DD15 I/O 3-state

19 GND 20 KEY

21 DMARQ O 3-state 22 GND

23 DIOW- I TTL 24 GND

25 DIOR- I TTL 26 GND

27 IORDY O 3-state 28 CSEL I TTL

29 DMACK- I TTL 30 GND

31 INTRQ O 3-state 32 (reserved)

33 DA01 I TTL 34 PDIAG- I/O OD

35 DA00 I TTL 36 DA02 I TTL

37 CS0- I TTL 38 CS1- I TTL

39 DASP- I/O OD 40 GND

41 +5V logic power 42 +5V motor power

43 GND 44 (reserved)

PC-HDD40G User’s Guide

CONTEC CO., LTD.

3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan

Japanese http://www.contec.co.jp/

English http://www.contec.com/ A-51-347 (LYGW173)

Chinese http://www.contec.com.cn/ 07122010_rev3 [10172006]

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

Contec PC-HDD40G Owner's manual

Contec PC-HDD40G Owner's manual

Contec PC-HDD40G Owner's manual

Related papers

Other documents