Eurotech AIM104-RELAY8-IN8 Owner's manual

Type
Owner's manual
Issue H - August 2009 - ETH_AIM104-RELAY/IN8_USM
DIGITAL TECHNOLOGIES FOR A BETTER WORLD
www.eurotech.com
USER MANUAL
AIM104-RELAY8/IN8
8 Channel RS232 PC/104 Board
DISCLAIMER
The information in this document is subject to change without notice and should not be construed as a commitment
by any Eurotech company. While reasonable precautions have been taken, Eurotech assumes no responsibility for
any error that may appear in this document.
WARRANTY
This product is supplied with a 3 year limited warranty. The product warranty covers failure of any Eurotech
manufactured product caused by manufacturing defects. The warranty on all third party manufactured products
utilised by Eurotech is limited to 1 year. Eurotech will make all reasonable effort to repair the product or replace it
with an identical variant. Eurotech reserves the right to replace the returned product with an alternative variant or
an equivalent fit, form and functional product. Delivery charges will apply to all returned products. Please check
www.eurotech.com
for information about Product Return Forms.
TRADEMARKS
Eurotech® is a registered trademark of Eurotech, Inc. Catalyst™ is a trademark of Eurotech, Inc. All other product
or service names are property of their respective owners.
All other trademarks recognised.
REVISION HISTORY
Issue no. PCB Date Comments
Issue A V1.1A
September 20th,
1996
First full release of manual.
Issue B V1.2
December 23rd,
1996
Edits to J538, J541, J559, and AIM104 software library.
Issue C V1.2 June 4th, 1997 [ECO 2494, 2502, 2516]
Issue D V1.3
November 16th,
1998
[ECO 2679 and 2773]
Issue E V1.3 February 11th, 1999 [ECO2800]
Issue F V1.3
September 25th,
2006
Revised format and content.
Issue G V1.3
December 21st,
2007
Revised format and content.
Issue H V1.3 August 20th, 2009 Revised format.
© 2009 Eurotech. All rights reserved.
For contact details, see page 15
.
Contents
Issue H
3
Contents
Introduction.....................................................................................................................................4
Handling your board safely.................................................................................................5
About this manual ...........................................................................................................................6
Conventions .......................................................................................................................6
Getting started ................................................................................................................................7
What items are provided? ..................................................................................................7
Unpacking and connecting up ............................................................................................7
Operation........................................................................................................................................8
Links ...............................................................................................................................................9
I/O map.........................................................................................................................................10
Address selection ......................................................................................................................... 11
Input filter selection.......................................................................................................................12
Output connector (PL1) pin assignments......................................................................................13
Appendix A – RoHS-6 Compliance - Materials Declaration Form .................................................14
Eurotech Group Worldwide Presence...........................................................................................15
AIM104-RELAY8/IN8 user manual
Issue H
4
Introduction
The AIM104-RELAY8/IN8 is an 8-bit PC/104 module providing eight changeover relays
and eight opto-isolated inputs. The module provides up to 1500V electrical isolation
between the PC/104 based control system and the electrical system you are controlling.
The isolation between adjacent channels is limited to 100V by the wiring and connectors.
The power switching rating for the relay contacts is 60W (resistive load). The relays and
board layout are designed to switch voltages up to 220V DC (125V AC), and currents up
to 1.0A. However, the Low Voltage Directive specifies that the product can only be safely
used up to 48V DC.
The board includes jumper options for each digital input to select a 10ms input debounce
filter.
Features
Eight changeover relays with a power switching rating of 60W (resistive load).
Switching voltage up to 48V DC and switching currents up to 1.0A.
Output status readback register.
Relay drivers disabled on power up and reset.
Both normally closed (NC) and normally open (NO) relay terminals are available at
the I/O connector.
Eight opto-isolated inputs.
Opto-input switching voltage: 10V to 30V.
Maximum input frequency: Filter disabled: 10KHz.
Filter enabled: 50Hz.
Input switching time (at 24v): Filter disabled: Switching ON: 5s.
Switching OFF: 50s.
Filter enabled: Switching ON: 10ms.
Switching OFF: 5ms.
All inputs include reverse protection diodes.
Board access LED.
Operating temperature range: -20°C to +70°C.
Power consumption: +5V +/- 0.25V 250mA typical.
MTBF: 91,195 hours (using generic figures from MIL-HDBK-217F at ground benign).
Introduction
Issue H
5
Handling your board safely
Anti-static handling
This board contains CMOS devices. These could be damaged in the event of static
electricity being discharged through them. Observe anti-static precautions at all times
when handling circuit boards. This includes storing boards in appropriate anti-static
packaging and wearing a wrist strap when handling them.
Electromagnetic compatibility (EMC)
The AIM104-RELAY8/IN8 is classified as a ‘component’ with regard to the European
Community EMC regulations and it is the user’s responsibility to ensure that systems
using the board are compliant with the appropriate EMC standards.
The opto-isolation provides a good barrier for noise emissions generated by the high
frequency host PC/104 system. The AIM104-RELAY8/IN8 includes additional filter
components on-board to minimise the emissions of high frequency noise. Because of
this, the earth tab supplied with the module must be connected to the chassis of the
system by a good earth wire.
If the electronic system requires input protection against high voltage transients (to meet
CE requirements), it is recommended that an external interface board is located at the
point where the external wiring enters the electronic system enclosure:
Packaging
Should a board need to be returned to Eurotech, please ensure that it is adequately
packed, preferably in the original packing material.
RoHS compliance
The European RoHS Directive (Restriction on the Use of Certain Hazardous Substances
– Directive 2002/95/EC) limits the amount of six specific substances within the
composition of the product. The AIM104-RELAY8/IN8 is available as an RoHS-6
compliant option and is identified by an -R6 suffix in the product order code. A full RoHS
Compliance Materials Declaration Form is included in Appendix A – RoHS-6 Compliance
- Materials Declaration Form
, page 14. Further information about RoHS compliance is
available on the Eurotech website: www.eurotech.com
AIM104-RELAY8/IN8 user manual
Issue H
6
About this manual
This manual describes the operation and use of the AIM104-RELAY8/IN8 PC/104
module. It is both a reference and user manual and includes information about all
aspects of the module.
Conventions
Symbols
The following symbols are used in this guide:
Symbol Explanation
Note - information that requires your attention.
Tip - a handy hint that may provide a useful alternative or save time.
Caution – proceeding with a course of action may damage your
equipment or result in loss of data.
Getting started
Issue H
7
Getting started
What items are provided?
The AIM104-RELAY8/IN8 is supplied with the following items:
The AIM104-RELAY8/IN8 board.
Mounting kit.
Unpacking and connecting up
To begin using the AIM104-RELAY8/IN8 board, follow these steps:
1 Power down your computer.
2 Install the board in a spare PCI slot.
3 Power up your computer and install the appropriate driver available from our
website www.eurotech.com.

AIM104-RELAY8/IN8 user manual
Issue H
8
Operation
Each relay is switched on by writing a 1 to the relay output register. On power up or reset,
the output latches that drive the relay drivers are disabled. To enable them, write 01 to
address base +1. We recommend that, for system initialisation, you write the output
register with the required relay states before setting the relay enable bit. See the
following diagram:
The status of the opto-inputs is read from I/O address base+1. When an input channel is
switched on, the value read by the host is a 0. See the diagram below:
Links
Issue H
9
Links
Use LK1 to set the base address of the module. Inserting a jumper selects a 0 for the
address line value. The following diagrams illustrate the link positions:
Link position diagram [Address is 180h]
AIM104-RELAY8/IN8 user manual
Issue H
10
I/O map
The following table describes the register locations:
Address offset Register name Read/write Comments
00 Relay output Write Write to relays 0-7
00 Relay status Read Readback from relay drivers
01 Relay enable Write Enable relay driver latches
01 Opto-inputs Read Read opto-inputs 0-7
Address selection
Issue H
11
Address selection
The following table describes the address selection:
Selection Bit function
Relay outputs Bit 0-7 for relay 0-7:
0 = Relay NC contacts closed
1 = Relay NO contacts closed
Relay status Bit 0-7:
0 = Relay NC position
1 = Relay NO position
Relay enable Bit 0:
0 = All relays off (NC position)
1 = Relays controlled by relay output register
Opto-inputs Bit 0-7:
0 = Input ON
1 = Input OFF
AIM104-RELAY8/IN8 user manual
Issue H
12
Input filter selection
Each opto-isolated input channel can be set to include an input filter, in order to reduce
input reading errors caused by switch contact bounce. This is shown below:
Channel Link
Channel 0 Link 2A
Channel 7 Link 2H
Output connector (PL1) pin assignments
Issue H
13
Output connector (PL1) pin assignments
The following table shows the output connector (PL1) pin assignments:
Pin no. Function Pin no. Function
1 Common -ve input 2 Opto +ve input Bit 0
3 Opto +ve input Bit 1 4 Opto +ve input Bit 2
5 Opto +ve input Bit 3 6 Opto +ve input Bit 4
7 Opto +ve input Bit 5 8 Opto +ve input Bit 6
9 Opto +ve input Bit 7 10 Common -ve input
11 Not connected 12 Relay 0 common
13 Relay 0 NO 14 Relay 0 NC
15 Not connected 16 Not connected
17 Relay 1 common 18 Relay 1 NO
19 Relay 1 NC 20 Not connected
21 Not connected 22 Relay 2 common
23 Relay 2 NO 24 Relay 2 NC
25 Not connected 26 Not connected
27 Relay 3 common 28 Relay 3 NO
29 Relay 3 NC 30 Not connected
31 Not connected 32 Relay 4 common
33 Relay 4 NO 34 Relay 4 NC
35 Not connected 36 Not connected
37 Relay 5 common 38 Relay 5 NO
39 Relay 5 NC 40 Not connected
41 Not connected 42 Relay 6 common
43 Relay 6 NO 44 Relay 6 NC
45 Not connected 46 Not connected
47 Relay 7 common 48 Relay 7 NO
49 Relay 7 NC 50 Not connected
AIM104-RELAY8/IN8 user manual
Issue H
14
Appendix A – RoHS-6 Compliance - Materials
Declaration Form
Confirmation of Environmental Compatibility for Supplied Products
Substance Maximum concentration
Lead 0.1% by weight in homogeneous materials
Mercury 0.1% by weight in homogeneous materials
Hexavalent chromium 0.1% by weight in homogeneous materials
Polybrominated biphenyls (PBBs) 0.1% by weight in homogeneous materials
Polybrominated diphenyl ethers (PBDEs) 0.1% by weight in homogeneous materials
Cadmium 0.01% by weight in homogeneous materials
The products covered by this certificate include:
Product Name Eurotech Part Number
AIM104-RELAY8/IN8 AIM104-RELAY8/IN8-R6
Eurotech has based its material content knowledge on a combination of information provided by third
parties and auditing our suppliers and sub-contractors operational activities and arrangements. This
information is archived within the associated Technical Construction File. Eurotech has taken
reasonable steps to provide representative and accurate information, though may not have conducted
destructive testing or chemical analysis on incoming components and materials.
Additionally, packaging used by Eurotech for its products complies with the EU Directive 2004/12/EC in
that the total concentration of the heavy metals cadmium, hexavalent chromium, lead, and mercury do
not exceed 100 ppm.
AIM104-RELAY8/IN8 user manual
Eurotech Group Worldwide Presence
AMERICAS
North America
EUROTECH USA
US toll free +1 800.541.2003
tel. +1 301.490.4007
fax +1 301.490.4582
www.eurotech-inc.com
PARVUS CORPORATION
US toll-free +1 800.483.3152
tel. +1 801.483.1533
fax +1 801.483.1523
www.parvus.com
EUROPE
Central & Southern Europe
EUROTECH Italy
tel. +39 0433.485.411
fax +39 0433.485.499
www.eurotech.com
Western Europe
EUROTECH UK
tel. +44 (0) 1223.403410
fax +44 (0) 1223.410457
www.eurotech.com
EUROTECH France
tel. +33 04.72.89.00.90
fax +33 04.78.70.08.24
www.eurotech.com
Northern & Eastern Europe
EUROTECH Finland
tel. +358 9.477.888.0
fax +358 9.477.888.99
www.eurotech.com
ASIA
Japan
ADVANET
tel. +81 86.245.2861
fax +81 86.245.2860
www.advanet.co.jp
China
VANTRON
tel. + 86 28.85.12.39.30
fax +86 28.85.12.39.35
www.vantrontech.com.cn
www.eurotech.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Eurotech AIM104-RELAY8-IN8 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI