Power Fist 8724981 Owner's manual

Brand: Power Fist

Model: 8724981

Type: Owner's manual

V 4.1 8724981

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

660 lb Power

Wheelbarrow

8724981 660 lb Power Wheelbarrow V 4.1

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Engine Type 196cc Powerfist

Gearbox 4 speed (3 Forward and 1 Reverse)

Gearbox Lubricant Type API GL-5, GL-6 or SAE 85-95 Gear Oil

Capacity 1.5 litres

Load Capacity 660 lb (300 kg)

Box Dimensions (L x W x H) 33-7/8 x 24-3/4 x 1-3/8 in.

Weight (Empty)

394.5 lb (179 kg)

INTRODUCTION

The 660 lb Power Wheelbarrow is great for landscaping and construction

applications including hauling dirt, sod, sand, gravel, shrubs, etc. The rubber

tracks minimize ground damage and can easily travel over uneven surfaces. The

4 speed gearbox makes it easy to transport loads up to 660 lb (300 kg) across

rough terrain. The dump box is easy to empty and is secured in place by the

latched tipping handle.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

660 lb Power

Wheelbarrow

V 4.1 660 lb Power Wheelbarrow 8724981

Visit www.princessauto.com for more information 3

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice

is an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well lit and

free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from the

work area.

3. Store unused tools properly in a safe and dry location to prevent rust or

damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National Standards

Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

8724981 660 lb Power Wheelbarrow V 4.1

4 For technical questions call 1-800-665-8685

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in the

work environment.

5. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

6. This tool can cause hearing damage. Wear hearing protection gear with an

appropriate Noise Reduction Rating to withstand the decibel levels.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol

or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

4. Securely hold this tool using both hands. Using a tool with only one hand

can result in loss of control.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific function.

Do not modify or alter this tool or use it for an unintended purpose.

2. Do not exceed the power wheelbarrow’s load capacity (see Specifications).

3. Do not use the machine if the engine’s switch does not turn it on or off.

Any gasoline powered machine that cannot be controlled with the engine

switch is dangerous and must be replaced.

V 4.1 660 lb Power Wheelbarrow 8724981

Visit www.princessauto.com for more information 5

4. Position the machine in such a way that it cannot move during maintenance,

repairs, cleaning, adjustments, assembly of accessories or storage.

Unexpected movement can cause a crushing injury during these procedures.

5. Do not operate the machine in confined areas where there may be a risk of

crushing the operator between the machine and another object. Use

extreme caution when in reverse or pulling the machine towards you.

6. Never carry passengers on the power wheelbarrow.

7. Drive at a safe speed and adjust for the surface conditions and the load.

8. Never operate the machine on slopes where angle is over 20°.

a. Do not shift gears while on a slope.

b. Ensure the load is evenly balanced when moving over a slope in

forward or reverse.

9. The power wheelbarrow’s center-of-gravity will change when tipping a load

out. Ensure the machine is on firm, stable ground capable of supporting

the change as the load shifts.

a. Soft or slick surfaces may cause the power wheel barrow to tip or slip

during unloading.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the parts list are included.

Contents:

• Main Frame

• Handlebar Assembly

• Tipping Handle

• Dump Box

• Hardware

8724981 660 lb Power Wheelbarrow V 4.1

6 For technical questions call 1-800-665-8685

IDENTIFICATION KEY

A Engine Switch

B Throttle Control

C Right Steering Lever

D Clutch Control Lever

E Left Steering Lever

F Dump Box

G Gear Selection Lever

H Tipping Handle

I Track

J Gearbox

Engine Switch -The engine switch enables and disables the ignition system. The

engine switch must be in the ON position for the engine to run. Turning the

engine switch to the OFF position stops the engine.

Throttle Control - Controls engine speed. Set the power wheelbarrow’s speed to

low (L), middle and high (H) speed.

Right Steering Lever - Operate the lever to turn right.

Clutch Control Lever- Squeeze the control lever to engage the clutch. Release

the lever to disengage clutch.

Left Steering Lever - Operate the lever to turn left.

Gear Selection Lever – Switch between forward and reverse.

Tipping Handle - Pull the tipping handle up to release the dump box's locking

device and raise the dump box. Pull the tipping handle down to its original position.

When the dump box is lowered, the locking mechanism locks the dump box. Lift

the dump without using the tipping handle to confirm it is locked in position.

ASSEMBLY & INSTALLATION

When this manual refers to a part number, it refers to the included Parts List.

1. Mount the tipping handle onto the panel’s right side. Align the holes and

fasten with two M8x35 hex bolts, four washers and two nuts (Fig. 2).

Fig. 1

V 4.1 660 lb Power Wheelbarrow 8724981

Visit www.princessauto.com for more information 7

2. Align the holes of the handlebar with the mounting bracket and secure

each with a spring washer, flat washer and an M10x20 bolt. Fasten each

handlebar support onto the engine deck with a spring washer, flat washer

and an M8x25 hex bolt (Fig. 3).

3. Position the bottom panel inside the mounting bracket. Align the holes with

the mounting bracket. Insert a long pin through holes and secure each side

with a flat washer and cotter pin (Fig. 4).

OPERATION

Consult the engine manual for the correct procedure to start and stop

the engine.

1. Start the engine. After the engine warms up, adjust the throttle control (B)

to increase the engine speed.

2. Choose a gear with the gear selection lever (G) and slowly squeeze the

clutch control lever (D) to start moving. If the gear does not engage

straight away, slowly release the clutch lever and try again.

3. The power wheelbarrow has steering levers on the handlebars (C and E).

To turn right, squeeze the right steering lever to slow or stop the track on

that side. The power wheelbarrow will then turn in that direction.

The steering sensitivity increases in proportion to the speed of the

machine. Light pressure on the lever is all that is needed to turn an empty

machine. More pressure is required when the machine is loaded.

Fig. 2

Fig. 3

Fig. 4

8724981 660 lb Power Wheelbarrow V 4.1

8 For technical questions call 1-800-665-8685

4. When the clutch control lever is released, the machine will stop

automatically.

5. Move the Gear Select Lever (G) to neutral.

a. Switch the engine OFF as an additional safety precaution.

6. Dump the load by pulling the tipping handle (H) up to release the dump

box's locking device. Manually raise the dump box to dump the load.

Lower the dump box and the locking mechanism will automatically lock the

box into place. Confirm the dump box is locked into position by attempting

to lift the dump box without using the tipping handle.

DIFFICULT TERRAIN

The power wheelbarrow may be hard to control when carrying a full load on

difficult terrain. The following steps can reduce the chance of losing control of

the equipment.

1. Reduce the power wheelbarrow’s speed to low on difficult terrain such as

soft or frozen ground, on an incline or on loose gravel or stones. This will

allow more time to react to a potential loss of control.

2. Do not allow rapid acceleration, sudden stops or sharp turns. The load’s

momentum can cause the power wheelbarrow to tip or slide in an

unexpected direction.

3. The power wheelbarrow will tilt when the tracks pass over obstacles or

rough terrain.

4. Adverse weather conditions such as wind, rain, snow and ice can make the

power wheelbarrow more difficult to control. Reduce speed and evaluate

the terrain.

a. Rough terrain can wear down the rubber tracks quickly, impairing

their function and reducing their operational life,

5. Place a wedge against one of the tracks if the machine is stopped on a

steep slope.

V 4.1 660 lb Power Wheelbarrow 8724981

Visit www.princessauto.com for more information 9

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier to

control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components. Only use identical replacement parts when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Keep the tool handles clean, dry and free from oil/grease at all times.

5. Maintain the tool’s labels and name plates. These carry important information.

If unreadable or missing, contact Princess Auto Ltd. for replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

PREVENTIVE MAINTENANCE

Turn off the engine and place the gear selection lever into neutral. Wait until the

engine is cool. Remove all debris and other materials that may have

accumulated on the tracks, engine or chassis.

ADJUSTING THE CLUTCH

A worn clutch may require moving the clutch lever farther before the

clutch engages.

1. Set the clutch lever to its original position.

2. Remove slack from the clutch lever cable with the adjustment device and

counter-nut.

ADJUSTING THE STEERING

The steering system may become less responsive with wear and tear to the unit.

Adjust one steering lever, before adjusting the other one.

1. Loosen the locknut and unscrew the adjuster just enough to allow the

cable to move when force is applied. Do not loosen too much as traction

can be lost.

2. Eliminate slack in the cable and tighten the adjuster.

3. Tighten the locknut and test the tension in the steering lever.

8724981 660 lb Power Wheelbarrow V 4.1

10 For technical questions call 1-800-665-8685

TIGHTEN TRACKS

WARNING! An overtight track will impair the brake’s effectiveness. Test and

adjust the brakes after tightening the track. Replace the track if any

adjustment affects the brakes normal function.

A loose track can slip off the driving wheel. This can cause a hazardous situation or

damage to the equipment. Check the track’s tightness on a regular basis.

1. Set the machine on a flat surface of

asphalt, stone or pavement. Compact

ground is also acceptable.

2. Lift the machine and set it on blocks or

supports rated for the weight of the machine,

so that the tracks are approximately 4 in.

(100 mm) off the ground.

3. Measure the track midline vs. the horizontal

line. The reading must not be more than

10-15 mm. If the distance is greater,

proceed as follows (Fig. 5).

a. Tip the dump box and set it on blocks

or supports capable of holding the weight of the box.

b. Loosen locknut A.

c. Tighten bolt B until the correct tightness is restored to the track.

d. Secure bolt B by retightening locknut A to secure the bolt in place.

e. Return the dump box to its original position.

NOTICE! Replace the track if the guide wheel axle (#81) is fully extended

forward and the track is still too loose.

REPLACING A TRACK

WARNING! Keep hands away from the track and wheels when under power to

avoid a crushing injury.

Check the condition of the tracks periodically. Replace a track that is cracked

or frayed.

1. Set the machine on a flat surface of asphalt, stone or pavement. Compact

ground is also acceptable.

Fig. 5

V 4.1 660 lb Power Wheelbarrow 8724981

Visit www.princessauto.com for more information 11

2. Lift the machine and set it on jack stands or supports rated for the weight

of the machine. The tracks should be 4 in. (100 mm) off the ground.

3. Loosen locknut A and bolt B (Fig. 5) fully to release tension from the track.

4. Pull the track off the toothed drive wheel at the rear by hand if possible. An

alternative is to use a wood block and crowbar to remove the track.

a. Start the engine and shift the power wheelbarrow into reverse.

b. Place a long wood block against the track and drive wheel. The wood

block will lift the track off the drive wheel as it rotates. Place the

power wheelbarrow into neutral gear as soon as the track has lifted.

c. Pull the track towards the side with the crowbar until the track slides

off the wheel. Remove the wood block.

WARNING! Do this carefully to avoid tipping the machine over. The machine

is heavy and can cause a crushing injury.

d. Shut the engine OFF.

e. Pull the track off the other wheels.

5. Place the new track so the teeth

are on either side of the front

wheel. Position the track so it

aligns with the other wheels.

6. Place the track on the rear drive

wheel by hand if possible. Use a

crowbar to slip the track onto the

teeth of the drive wheel.

7. Start the engine and place the

power wheelbarrow in reverse until the drive wheel’s teeth slip into the

slotted holes of the track.

8. Adjust the track tension as explained in the section Tighten Tracks.

ENGINE MAINTENANCE

Refer to the Engine Manual included in your unit for the information on engine

maintenance. Your engine manual provides detailed information and a

maintenance schedule for performing the tasks.

Fig. 6

8724981 660 lb Power Wheelbarrow V 4.1

12 For technical questions call 1-800-665-8685

CLEANING

Never use a pressure washer to clean the power wheelbarrow. Water can

penetrate tight areas of the machine or its gearbox case and cause damage to

spindles, gears, bearings or the engine. This can shorten the equipment’s

operational life and reduce serviceability.

Do not use strong detergents or petroleum based cleaners when cleaning

plastic parts. Chemicals can damage plastics.

LUBRICATION

Inspect and lubricate the tool when required. Use a premium quality lithium

machine oil to lubricate the tool. Other lubricants may not be suitable and could

damage the tool or cause a malfunction during use.

GEARBOX

The gearbox is pre-lubricated and sealed at the factory. Replace the gearbox oil

after every 50 hours of use.

1. Position the equipment on a slight slope so the drain plug is lower than the

rest of the gearbox.

2. Run the equipment briefly to mix and warm the gearbox oil.

3. Place a receptacle below the opening to catch the waste oil.

4. Remove the gearbox’s oil filler plug (Fig. 7-2), then the drain plug (Fig. 7-

1) to drain the oil.

5. Examine the oil for metal chips to determine if the gearbox may need

further maintenance.

6. Reinsert the gearbox’s drain plug.

7. Fill the gearbox with 1.5 litres of EP gear oil

through the filler opening. Use an API GL-5,

GL-6 or SAE 85-95 lubricant.

8. Reinsert the filler plug. Clean up any spilled oil.

9. Run the engine for several minutes and check

for leaks before using the equipment.

Fig. 7

V 4.1 660 lb Power Wheelbarrow 8724981

Visit www.princessauto.com for more information 13

STORAGE

If the power wheelbarrow will not be used for a period be used for a period

longer than 30 days, follow the steps below to prepare your unit for storage.

Consult the engine manual for storage steps involving the engine.

1. Use clean cloths to clean off the outside of the machine and to keep the air

vents free of obstructions.

2. Inspect for any loose or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts.

3. Store your unit on flat ground in a clean, dry building that has good

ventilation.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing uncontrolled

discharge of waste oil.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Consult the engine manual for further troubleshooting steps and solutions.

Problem(s)

Possible Cause(s)

Power Fist 8724981 Owner's manual

Brand: Power Fist

Model: 8724981

Type: Owner's manual

Download PDF

report

in other languages

français: Power Fist 8724981 Le manuel du propriétaire

Power Fist 8724981 Owner's manual

Power Fist 8724981 Owner's manual

in other languages

Related papers

Other documents