Wacker Neuson DPU80rLem770 User manual

Operator's manual

Vibratory plate

DPU

80, 90, 110

Model DPU

Document 5100008833

Issue 08.2019

Version 11

Language en

100_0000_0001.fm

Printed in Germany

All rights are reserved, in particular the worldwide applicable copyright, right of duplication and right of

distribution.

This document may only be used by the recipient for the intended purpose. The document may not be

reproduced entirely or partially, or translated into any other language.

Reproduction or translation, even extracts thereof, only with written approval of Wacker Neuson

Produktion GmbH & Co. KG.

Any breach of the statutory regulations, in particular the protection of copyright, will lead to civil and

criminal prosecution.

Wacker Neuson Produktion GmbH & Co. KG is constantly working on the improvement of its products

as part of the technical further development. Therefore, we reserve the right to make changes to the

illustrations and descriptions in this documentation without incurring any obligation to make changes to

machines already delivered.

Errors excepted.

The machine on the cover may have special equipment (options).

Manufacturer

Wacker Neuson Produktion GmbH & Co. KG

Wackerstraße 6

D-85084 Reichertshofen

www.wackerneuson.com

Tel.: +4984533403200

E-Mail: service-[email protected]

Original operator's manual

1 CALIFORNIA Proposition 65 Warning

100_0000_0024.fm 3

1 CALIFORNIA Proposition 65 Warning

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Diesel engine exhaust and some of its constituents are known to the State of

California to cause cancer, birth defects, and other reproductive harm.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead

compounds, and other chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

Table of contents

4 5100008833IVZ.fm

1 CALIFORNIA Proposition 65 Warning .................................................................................3

2 Preface ...................................................................................................................................6

3 Introduction ...........................................................................................................................7

3.1 Using the manual......................................................................................................................... 7

3.2 Storage location of the manual.................................................................................................... 7

3.3 Accident prevention regulations................................................................................................... 7

3.4 More information.......................................................................................................................... 7

3.5 Target group................................................................................................................................ 7

3.6 Explanation of symbols................................................................................................................ 7

3.7 Wacker Neuson Contact partner ................................................................................................. 8

3.8 Disclaimer.................................................................................................................................... 8

3.9 Product identification of the machine........................................................................................... 8

4 Security ..................................................................................................................................9

4.1 Policy........................................................................................................................................... 9

4.2 Areas of responsibility of the operator......................................................................................... 9

4.3 Operator responsibilities............................................................................................................ 10

4.4 Personnel qualification............................................................................................................... 10

4.5 Residual dangers....................................................................................................................... 10

4.6 General safety instructions ........................................................................................................ 10

4.7 Specific safety instructions – Vibratory plates ........................................................................... 11

4.8 Specific safety instructions – remote controlled vibratory plates............................................... 12

4.9 General safety instructions - Combustion engines.................................................................... 12

4.10 General safety instructions – fuel, lubricants and coolants........................................................ 12

4.11 General safety instructions – starter batteries ........................................................................... 13

4.12 Maintenance.............................................................................................................................. 13

4.13 Personal Protective Equipment ................................................................................................. 13

4.14 Safety devices ........................................................................................................................... 14

4.15 Behavior in dangerous situations............................................................................................... 15

5 Safety and information labels ............................................................................................16

5.1 Safety and information labels on the remote control ................................................................. 17

6 Setup and function ..............................................................................................................18

6.1 Standard package...................................................................................................................... 18

6.2 Application areas....................................................................................................................... 18

6.3 Short description........................................................................................................................ 18

6.4 Versions..................................................................................................................................... 20

7 Components and operator's controls ...............................................................................21

7.1 Components .............................................................................................................................. 21

7.2 Operator's controls..................................................................................................................... 22

7.3 Components and operator’s controls – remote control unit....................................................... 25

8 Transport ..............................................................................................................................27

8.1 Loading and transport................................................................................................................ 27

9 Operation and use ...............................................................................................................29

9.1 Before commissioning ............................................................................................................... 29

9.2 Notes about operation ............................................................................................................... 31

9.3 Commissioning.......................................................................................................................... 32

9.4 Operation................................................................................................................................... 36

9.5 Decommissioning ...................................................................................................................... 39

9.6 Setting the transmission channel (remote control) .................................................................... 44

9.7 Operating the diagnostic menu.................................................................................................. 44

9.8 Operation of the configuration menu ......................................................................................... 45

Inhalt

Table of Contents

5100008833IVZ.fm 5

10 Maintenance .........................................................................................................................46

10.1 Maintenance schedule – One-time maintenance job................................................................. 46

10.2 Maintenance schedule – daily maintenance jobs...................................................................... 47

10.3 Maintenance schedule – regular intervals................................................................................. 47

10.4 Maintenance jobs....................................................................................................................... 48

11 Troubleshooting ..................................................................................................................55

11.1 Troubleshooting table – machine............................................................................................... 55

11.2 Troubleshooting table – receiving units..................................................................................... 56

11.3 Troubleshooting table - center pole head head indicator light................................................... 56

11.4 Troubleshooting table – remote control..................................................................................... 57

11.5 Troubleshooting table – display................................................................................................. 58

11.6 Telematics Fault Table .............................................................................................................. 62

11.7 Perform jump start with donor starter battery ............................................................................ 63

12 Disposal ................................................................................................................................65

12.1 Disposal of batteries.................................................................................................................. 65

13 Accessories .........................................................................................................................66

14 Technical data ......................................................................................................................67

14.1 DPU80....................................................................................................................................... 67

14.2 DPU80r...................................................................................................................................... 68

14.3 DPU90....................................................................................................................................... 69

14.4 DPU90r...................................................................................................................................... 70

14.5 DPU110..................................................................................................................................... 71

14.6 DPU110r.................................................................................................................................... 72

14.7 Combustion engine.................................................................................................................... 73

14.8 US combustion engine............................................................................................................... 74

15 Emission control systems information and warranty ......................................................75

EC Declaration of Conformity

....................................................................................76

DIN EN ISO 9001 certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

2 Preface

6 100_0000_0002.fm

2 Preface

This operator's manual contains important information and procedures for the safe, proper and economic

operation of this Wacker Neuson machine. Carefully reading, understanding and observing is an aid to

avoiding hazards, repair costs and downtime, and therefore to increasing the availability and service life

of the machine.

This operator's manual is not a manual for extensive maintenance or repair work. Such work should be

carried out by Wacker Neuson service or by technically trained personnel. The Wacker Neuson machine

should be operated and maintained in accordance with this operator's manual. An improper operation or

improper maintenance can pose dangers. Therefore, the operator's manual should be constantly

available at the location of the machine.

Defective machine parts must be exchanged immediately!

If you have any questions concerning the operation or maintenance, a Wacker Neuson contact person

is always available.

3 Introduction

100_0000_0013.fm 7

3 Introduction

3.1 Using the manual

This manual is to be considered part of the machine and should be carefully stored during the entire

service life of the machine. This manual shall be transferred to subsequent owners or users of the

machine.

3.2 Storage location of the manual

This manual is part of the machine and must be kept in the immediate vicinity of the machine and made

accessible to staff at all times.

If this manual is lost, or if a second copy is required, there are two options to obtain a replacement:

 Download from the Internet: www.wackerneuson.com

 Contact your Wacker Neuson contact partner.

3.3 Accident prevention regulations

In addition to the notes and safety instructions in this manual, the local accident prevention regulations

as well as the national health and safety regulations apply.

3.4 More information

This manual applies to various machine types from one product series. For this reason, some figures

may vary slightly in appearance from the machine purchased. Depending on the model, there may be

descriptions of components that are not included in the standard package.

The information contained in this manual is based on machines manufactured up to the time of printing.

Wacker Neuson reserves the right to change this information.

The manufacturer shall immediately include any modifications or additions in this manual.

3.5 Target group

Individuals working with this machine must be regularly trained on the dangers of handling the machine.

This manual is intended for the following people:

Operating personnel:

These individuals have been trained on the machine and informed about the possible dangers in the

event of improper conduct.

Technically trained personnel:

These people have professional training as well as additional knowledge and experience. They are able

to assess the tasks assigned to them and recognize possible dangers.

3.6 Explanation of symbols

This manual contains specially emphasized safety instructions in the following categories: DANGER,

WARNING, CAUTION and NOTICE.

Before performing any work on or with this machine, the notes and safety instructions must be read and

understood. All notes and safety instructions in this manual must be passed on to the maintenance,

repair, and transport personnel.

DANGER

This combination of symbol and signal word indicates a hazardous situation that will lead

to death or serious injury if it is not avoided.

WARNING

This combination of symbol and signal word indicates a hazardous situation that can lead

to death or serious injury if it is not avoided.

CAUTION

This combination of symbol and signal word indicates a hazardous situation that can lead

to minor injury or damage to the machine if it is not avoided.

3 Introduction

8 100_0000_0013.fm

3.7 Wacker Neuson Contact partner

Depending on the country, the Wacker Neuson contact partner is a Wacker Neuson service department,

a Wacker Neuson subsidiary, or a Wacker Neuson dealer.

On the Internet at www.wackerneuson.com.

3.8 Disclaimer

For the following violations, Wacker Neuson dismisses any liability for personal injury or material

damage:

 Failure to follow this manual.

 Unintended use.

 Deployment of untrained personnel.

 Using non-approved spare parts and accessories.

 Improper handling.

 Structural modifications of any kind.

 Failure to observe the "General Terms and Conditions" (GT&Cs).

3.9 Product identification of the machine

Data of the type label

The type label contains information that uniquely identifies this machine. This information is required for

ordering spare parts and when inquiring about technical issues.

 Enter information about the machine in the following table:

NOTICE

Supplementary information.

Designation Your information

Group and model

Year of manufacture

Machine number

Version no.

Item no.

4 Security

100_0202_si_0008.fm 9

4Security

4.1 Policy

In keeping with the latest technological developments

The machine has been built in keeping with the latest technological developments and the recognized

technical safety rules. Nevertheless, improper use can result in hazards to life and limb of the user or

third parties as well as damage to the equipment and other material assets.

Proper use

The machine may only be used for the following purposes:

 Soil compaction.

 Asphalt compaction.

 Vibration of sett paving (paving stones).

The machine may not be used for the following purposes:

 Compaction of very cohesive soils.

 Compaction of frozen soils.

 Compaction of hard, non-compressible soils.

 Compaction of non-load-bearing soils.

Use in accordance with the intended purpose also includes the observation of all safety instructions in

this manual as well as complying with the prescribed care and maintenance instructions.

Any use that exceeds or is not in accordance with the intended purpose is considered improper. The

manufacturer's liability and warranty are canceled for any damage resulting from improper use. The risk

lies entirely with the operator.

Structural changes

Structural modifications may not be undertaken without the written permission of the manufacturer.

Unapproved structural changes may result in risks to the operator and/or third parties as well as damage

to the machine.

In the case of unauthorized structural changes, the liability and warranty of the manufacturer are no

longer applicable.

The following cases are considered structural changes:

 Opening the machine and the permanent removal of components.

 Installing spare parts that do not originate from Wacker Neuson or are not comparable in the design

system and quality of the original parts.

 Attaching any accessories that do not originate from Wacker Neuson .

Spare parts or accessories that originate from Wacker Neuson can be safely mounted. They can be

found on the Internet under www.wackerneuson.com.

4.2 Areas of responsibility of the operator

The operator is the individual who personally operates this machine for industrial or commercial

purposes or who entrusts a third party with the use. The operator bears legal responsibility for his/her

protection as well as that of third parties.

The user must make the operator's manual available to the operator and ensure that this has been read

and understood.

The manual must be kept next to the machine or place of use.

The operator must hand over the manual to subsequent operators or owners of the machine.

NOTICE

Read and comply with all notes and safety instructions in this manual. Failure to comply

with these instructions can cause electric shock, fire and/or serious injuries as well as

damage to the machine and/or damage to other objects. Keep safety instructions and

notes for the future.

4 Security

10 100_0202_si_0008.fm

The country-specific regulations, standards, and guidelines on accident prevention and environmental

protection must be observed. The operator’s manual must supplemented with additional instructions that

take regulatory, national, or generally applicable safety standards into consideration.

4.3 Operator responsibilities

 Know and implement the applicable industrial safety regulations.

 Use a risk assessment to identify the dangers that result from the working conditions at the site of

application.

 Create operating instructions for the operation of this machine.

 Periodically check whether the user instructions correspond to the current state of regulations.

 Clearly regulate and specify responsibilities for operation, troubleshooting, maintenance, and

cleaning.

 Regularly train employees and inform them about potential hazards.

 Provide employees with the necessary equipment.

4.4 Personnel qualification

This machine may only be installed and operated by trained personnel.

Faulty operation, misuse or operation by untrained personnel can endanger health of the operator or

third parties and lead to damage to or total loss of the machine.

In addition, the operator should be:

 physically and mentally fit.

 not under the influence of drugs, alcohol or medication that can impair responsiveness.

 familiar with the safety instructions in this manual.

 familiar with the intended use of this machine.

 the minimum age (18 years) to operate this machine.

 Be instructed in the independent operation of the machine.

 Be authorized to operate machines and systems independently according to the standards of safety

engineering.

4.5 Residual dangers

Residual dangers in particular are hazards when dealing with machines that, despite a safe design,

cannot be eliminated.

These residual dangers are not obvious and may be the source of a possible injury or health hazard.

If unforeseeable residual dangers occur, the operation of the machine is to be stopped immediately and

the competent supervisor is to be informed. This supervisor shall make the following decisions and

initiate everything required to eliminate the occurring danger.

If necessary, the machine manufacturer is to be informed.

4.6 General safety instructions

The safety instructions in this chapter include the "General Safety Instructions", which should be

reported in the manual in accordance with the applicable standards. There may be information that is

not relevant to this machine.

4.6.1 Working area

 Before starting work, familiarize yourself with the working environment e.g. load-bearing capacity of

the floor or obstacles in the environment.

 Make working area safe for the public transport sector.

 Necessary fuse protection of walls and ceilings e.g. in trenches.

 Keep the working area tidy. Cluttered or dark working areas can lead to accidents.

 Using this machine in an explosive atmosphere is prohibited.

 When using this machine, children and unauthorized individuals must be kept away. Distraction can

lead to loss of control of the machine.

 Always protect the machine against tilting, rolling, sliding, and crashing. Risk of injury!

4.6.2 Service

 The machine should only be maintained/repaired by technically trained personnel.

 Use only original spare parts and accessories. This ensures the operational safety of the machine.

4 Security

100_0202_si_0008.fm 11

Screw connections

All screw connections must meet the prescribed specifications and must be firmly screwed together.

Observe the tightening torques!

The screws and nuts may not be damaged, bent or deformed.

Pay particular attention to:

 Captive nuts and micro-encapsulated screws may not be reused once loosened. The locking effect

is lost.

 Screw connections with adhesive securing/liquid adhesives (e.g. Loctite) must be cleaned after

loosening and must be provided new adhesive.

4.6.3 Personal safety

 Working under the influence of drugs, alcohol, or drugs can lead to serious injuries.

 Protective equipment should be worn for all work. Appropriate personal protective equipment

considerably reduces the risk of injury.

 Remove any tools before the machine is put into operation. Tools that are located on a rotating

machine part can be ejected and cause serious injury.

 Always ensure good footing.

 In the case of extensive work with this machine, long-term vibration-induced damage cannot be ruled

out. For exact values of vibration measurement, refer to the Technical Data section.

 Wear suitable clothing. Keep loose clothing, gloves, jewelry, and long hair away from moving/rotating

machine parts. Danger of being pulled!

 Ensure that no other individuals are in the danger zone!

4.6.4 Handling and use

 Handle machines with care. Do not operate machines with defective components or operator’s

controls. Immediately replace defective components or operator's controls. Machines with defective

components or operator's controls carry a high risk of injury!

 The operator's controls of the machine shall not be improperly locked, manipulated, or changed.

 The machine, accessories, and tools should be used in accordance with these instructions.

 Store unused machines out of reach of children. The machine may only be operated by authorized

personnel.

 After operation, store the cooled-down machine in a locked, clean, frost-protected, and dry location

that is inaccessible to children and other unauthorized individuals.

4.7 Specific safety instructions – Vibratory plates

4.7.1 External influences

In the case of the following external influences, the vibratory plate may not be operated:

 In heavy rain on sloped surfaces. Risk of slipping!

 Oil field environments – methane leaks from bottom. Explosion hazard!

 In dry, flammable vegetation. Fire hazard!

 In potentially explosive areas. Explosion hazard!

NOTICE

Observe the instructions of the liquid adhesive manufacturer.

4 Security

12 100_0202_si_0008.fm

4.7.2 Operational safety

 When operating the machine, make sure that no gas, water, or electric lines are damaged.

 The machine must not be operated in tunnels or enclosed spaces.

 Pay maximum attention near drops or slopes. Risk of crashing!

 The operator must not leave the machine while it is in operation.

 Do not leave the machine unattended. Risk of injury!

 Protect the machine from unauthorized operation. When not in use, lock the rear protective hood with

a padlock.

 Delimit spacious workspace and restrict access to unauthorized individuals. Risk of injury!

 The operator of the machine must ensure that all individuals keep a minimum distance of 2 m from

the machine while it is in operation.

 Do not use any starting aid sprays. These can cause misfires as well as engine damage. Fire hazard!

 When operating the machine on sloped surfaces, always approach slopes from below and always

stay above the machine on a slope. The machine could slip or tip over.

 Do not exceed max. allowable slanting position of the machine – possible failure of the engine

lubrication, see chapter Technical Data.

 Only Wacker Neusonuse starter batteries. These are vibration proof and therefore suitable for the

high vibration exposure.

4.7.3 Minimum safety distances

Compaction work near buildings can cause damage to buildings. Therefore, all potential effects and

vibrations on surrounding buildings must be checked in advance.

The relevant rules and regulations for measuring, evaluating and reducing vibration emissions,

especially the DIN 4150-3, must be considered.

Wacker Neuson assumes no liability for any damage to buildings.

4.8 Specific safety instructions – remote controlled vibratory plates

 Always keep remote control and receiving units of the machine clean and free from dry, oil, and

grease.

 Remote control and receiving units must not be taped over or covered.

 During operation, the remote control should always be aimed directly at the machine. A clear line of

sight must be maintained – infrared signals can be reflected.

 The operator should remain 5 meters behind the machine in accordance with the intended purpose.

4.9 General safety instructions - Combustion engines

The following notes must be observed:

 Before starting work, check the engine to ensure there are no leaks and/or cracks in the fuel lines,

tank, and fuel cap.

 Do not operate a defective engine. Replace damaged parts immediately.

 The pre-set engine speed may not be adjusted. This could lead to engine damage.

 Make sure that the exhaust system of the engine is free of debris. Fire hazard!

 Switch off before refueling the engine.

 Use the correct fuel type. The fuel may not be mixed with other liquids.

 Use clean filling aids for refueling. Do not spill fuel. Immediately wipe up any spilled fuel.

 The engine may not be started near spilled fuel. Explosion hazard!

 When operating in partially enclosed spaces, adequate ventilation must be ensured. Do not inhale

exhaust fumes. Risk of poisoning!

 The engine surface and exhaust system can quickly become extremely hot. Risk of burns!

 Do not open the radiator cap when the engine is hot – Use caution: hot coolant!

4.10 General safety instructions – fuel, lubricants and coolants

NOTICE

This machine is outfitted with an EPA-certified engine.

Adjusting the revolutions per minute (RPM) impacts the EPA-certification and the

emissions. Settings for this engine may only be changed by a professional.

For more information, contact the manufacturer or your Wacker Neuson contact partner.

4 Security

100_0202_si_0008.fm 13

The following notes must be observed:

 Always wear safety glasses and protective gloves when handling fuel, lubricants, and coolants. If

hydraulic oil, fuel, oil, or coolant gets into your eyes, consult a physician immediately.

 Avoid direct skin contact with fuel, lubricants and coolants. Immediately rinse skin with soap and

water.

 Do not eat or drink while working with fuel, lubricants and coolants

 Hydraulic oil or fuel contaminated by dirt or water can cause premature wear or failure of the machine.

 Dispose of spilled fuel, lubricants and coolants according to the applicable provisions for

environmental protection.

 If fuel, lubricants and coolants escape from the machine, do not operate the machine any longer and

have it repaired immediately by the Wacker Neuson contact partner.

4.11 General safety instructions – starter batteries

The following notes must be observed:

 When disconnecting the starter battery, always disconnect the negative terminal first!

 When connecting the starter battery, always connect the positive terminal first! Fasten battery

terminal cover!

 Flames, sparks, and smoking are prohibited when handling starter batteries.

 Starter batteries contain corrosive acid. Wear acid-proof protective gloves and safety glasses when

handling starter batteries.

 Prevent incorrect connection of the starter battery or bridging of the terminals with tools. Risk of short

circuit!

4.12 Maintenance

The following notes must be observed:

 This machine may not be maintained, repaired, adjusted or cleaned while switched on. Disconnect

the starter battery when working on the electrical system!

 Adhere to maintenance intervals.

 After each maintenance or repair, the safety devices on this machine must be reattached.

 Observe the maintenance schedule. Identified work must be taken over by the service department of

the Wacker Neuson contact partner.

 Immediately replace worn or damaged machine parts. Only use spare parts from Wacker Neuson.

 Keep the machine clean.

 Missing, damaged, or illegible safety warning labels should be replaced immediately. Safety stickers

contain important information for the protection of the operator.

 Maintenance jobs must be carried out in clean and dry environment (e.g. in a workshop).

4.13 Personal Protective Equipment

NOTICE

To prevent personal injury when handling this machine, personal protective equipment

must be worn when working on or around this machine.

Pictogram Significance Description

Wear safety shoes! Safety shoes provide protection from bruises, falling

objects, and slipping.

4 Security

14 100_0202_si_0008.fm

4.14 Safety devices

Safety devices protect the user of this machine from being exposed to existing hazards. These are

barriers (separating protective devices) or other technical measures. This prevents the user from being

exposed to a danger. The source of danger will be eliminated in certain situations or the danger will be

reduced.

This machine has the following safety equipment:

Protective frame / protective hoods

The protective frame with the protective hoods protects the operator in particular from hot engine parts

and noise.

Wear protective gloves! Protective gloves provide protection from abrasion,

cuts, punctures, and hot surfaces.

Wear ear protection! Ear protection provides protection from permanent

hearing impairment.

NOTICE

With this machine, the permissible, country-specific noise limit (personal rating level) may

be exceeded. Therefore, ear protection must be worn. For exact values regarding noise

emissions, refer to Technical Data section.

When wearing ear protection, remain alert because your ability to hear noises such as

screams or signal tones is restricted.

Wacker Neuson recommends always wearing ear protection.

Item Description Item Description

1 Protective frame / protective hoods 3 Emergency stop switch

2 Automatic central position of control handle

NOTICE

Always tighten loosened screwed connections with the prescribed torque setting.

Pictogram Significance Description

1

3

2

1

3

4 Security

100_0202_si_0008.fm 15

Emergency stop switch

The emergency stop switch is used solely to switch off the machine in the case of danger. Activating the

emergency stop switch results in the machine immediately switching off. Operation can only be resumed

after unlocking the emergency stop switch.

Automatic central position of control handle

If the control handle is released in full load, it automatically returns to the central position and the

machine enters stand vibration.

4.14.1 Safety shutdown – Remote-controlled machinery

The machine is operated via an infra-red remote control. For safety reasons, it switches off

vibration and movement in the following situations:

 When the operator enters the proximity area (approx. 1–2 meters from a receiving unit).

 When the operator leaves the receiving area (a maximum of 20 meters from the machine).

 Interruption of the clear line of sight between the remote control and receiving units of the machine.

 Power failure of remote control and/or machine.

4.15 Behavior in dangerous situations

Preventive measures:

 Always be prepared for accidents.

 Keep first aid equipment on hand.

 Make sure that all employees are familiar with accident reporting, first aid, and rescue facilities.

 Keep access routes clear for emergency vehicles.

 Make sure that employees receive first aid training.

Measures in the case of an emergency:

 Immediately take the machine out of operation.

 Remove injured and other people from the danger zone.

 Initiate first aid measures.

 Alert rescuers.

 Keep access routes clear for emergency vehicles.

 Inform the person responsible at the site of application.

5 Safety and information labels

16 100_0202_ls_0009.fm

5 Safety and information labels

The following labels are found on and in the machines:

WARNING

Illegible symbols

Over time, labels and signs on the machines can become dirty or otherwise

unrecognizable.

 Keep all safety, warning, and operating instructions on the machine in a legible

condition.

 Replace damaged labels and signs immediately.

Item Label Description

1 Use personal protection equipment in order to prevent injuries and

health hazards.

 Ear protection.

 Read operator's manual.

2 Falling machines can cause serious injury.

 Only lift machine at the central lifting point with certified lifting gear

and tackle (safety load hook).

 Do not lift the machine on the central lifting point with an excavator

bucket.

 Do not lift the machine on the central lifting point with a forklift.

3 Guaranteed sound power level.

4 Center pole machines Falling machines can cause serious injury.

 Do not lift the machine with the control handle or center pole.

5 The coolant is under pressure.

Hot coolant can spurt out and cause injury from scalding.

 Only open the cover of the radiator after the engine has cooled down.

6 Remote controlled machines

 Label identifies the remote control in the bracket.

 Label identifies the connection of the charging cable for charging.

1

2

3

4

5

6

7

8

11

10

9

0219175

0216633

0

2

0

0216635

5 Safety and information labels

100_0202_ls_0009.fm 17

5.1 Safety and information labels on the remote control

The following labels are found on the remote control:

7 US Machines Warning.

8 Closing the protective hood can lead to crushing wounds.

 When closing the protective hood, do not grab between the machine

and the protective hood.

9 Warning against hot surface.

10 Tie-down lugs.

11 US Machines Warning.

From chemicals that cause cancer, birth defects or other reproductive

damage.

Item Label Description

1 US Machines To prevent interference of the infrared transmission and

possible machine malfunction, do not attach to housing.

Clean before transmitter and receiver eye before

commissioning!

Clean remote control and receiving unit before

commissioning!

2 US Machines To prevent damage and possible malfunction of the

transmitter unit, do not open housing! See operator's manual!

Item Label Description

0219261

WARNING

WARNUNG

ADVERTENCIA

ADVERTISSEMENT

0219176

0207747

2

1

6 Setup and function

18 100_0202_sf_0010.fm

6 Setup and function

6.1 Standard package

The machine is delivered fully assembled and is ready for operation out of the box.

The standard package includes:

 Vibratory plate

 Remote control (optional)

 Operator’s manual

 Manual for machine configuration (includes PIN data of the machine)

6.2 Application areas

The vibratory plate is used for compacting soil. It is used in gardening and landscaping as well as civil

engineering, road construction, and paving.

6.3 Short description

The water-cooled drive motor in the upper mass hydraulically powers the eccentric weight of the base

plate.

The exciter is designed as a centrally mounted exciter. This principle enables the modification of the

direction of oscillation (by adjusting the eccentric weights) and thus the movement of the machine

(forwards, in reverse or on-the-spot vibration).

For the exciter of the remote controlled machine, eccentric weights can be individually adjusted in order

to allow steering movements.In addition, spot vibration can be adjusted.

The radiator reduces the temperature of the engine coolant as well as that of the hydraulic oil.

The intake air is aspirated in the cold area between the radiator and the rear protective hood and purified

via an air filter equipped with a pre-cleaner.

The muffler discharges exhaust fumes from the front.

To start the drive motor automatically, the glow plugs are preheated. The speed of the drive motor is

controlled via a lifting magnet. The machine is switched off via an electrically controlled solenoid valve

on the fuel filter.

The electrical control unit is located in the electrical box.

The operator’s controls are located at the electrical box and at the center pole head.

The maintenance-free starter battery is located below the bracket for the remote control.

The machine is controlled with the center pole. For the remote controlled machine, it is controlled

exclusively via the remote control.

6.3.1 Remote-control vibratory plate

The machine is controlled exclusively by the remote control.

Within the receiving area, the commands of the remote control are transmitted to the machine via

infrared signal.

For trouble-free transmission of the infrared signal, the remote control must always be aimed directly at

one of the receiving units of the machine.

The following commands are possible with the remote control:

 Start engine.

 Move machine with simultaneous vibration.

 Switch spot vibration on and off

 Move machine slow or fast.

 Switch off engine.

Infrared system

If the remote control has been activated by pressing the On/Off switch, it permanently sends infrared

signals to the respective receiving unit of the machine.

The receiving unit of the machine converts the infrared signal into an electrical signal. The control

electronics the process the electrical signal and control the machine in accordance with the control

command.

6 Setup and function

100_0202_sf_0010.fm 19

In order for the machine to be able to execute the control commands, the remote control and machine

must be set to the same transmission channel.

Each machine has its own address for the transmission channel. Upon delivery, the transmitter unit is

set to the address of the machine and will only work with this machine. If the transmitter unit operates

another machine, this can be adjusted, see Setting the transmission channel (remote control) chapter.

Receiving area

Operation is only possible when the machine is within the receiving area. The receiving area is

approximately 20 meters from a receiving unit of the machine.

Within the receiving area, there must always be a clear line of sight between the remote control and the

machine.If there is no clear line of sight, the machine will cease all vibration and movement.

Outside of the receiving area, the machine will not receive the commands. The machine will stop

vibrating and moving.

Proximity area

If the machine comes within 1–2 meters (proximity area) of the operator, it will cease all vibration and

movement. Once the operator leaves the proximity area, the machine is once again able to receive

commands.

If the operator is laterally closer than 1–2 m from the machine or if the infrared signals of the remote

control are transmitted via reflection, a stopping of the vibration and movement is not guaranteed.

If another person comes within 1–2 meters (proximity area) of the machine, the machine will not cease

vibration and movement. The shutdown in the proximity area only works in connection with the remote

control unit.

6.3.2 Diagnostic system

The diagnostic system of the machine consists of control electronics and sensors that monitor various

components of the machine.

If the diagnostic system detects a fault or an error, this is signaled to the receiving unit by solid or flashing

red lights.A fault indication with error code appears on the display.

Each error code stands for a specific fault. The diagnostic system can distinguish between approx. 36

error codes.

In case of serious faults, the error code is entered into the error memory, and the machine will

automatically switch off the motor or deactivate itself.

6.3.3 Machine configuration system

In the machine configuration system, machine parameters can be changed by the user (e.g. switching

an activation PIN on or off).

Item Designation Item Designation

1 Receiver unit (front, rear) 3 Receiving area

2 Proximity area

1

2

3

6 Setup and function

20 100_0202_sf_0010.fm

6.3.4 Machine protection – installation (optional)

The acceleration load of the upper mass is monitored via a sensor. When a threshold value

corresponding to an operation of the vibratory plate on an extremely hard surface (concrete, asphalt) is

exceeded, a warning is given to the operator that the vibrator plate is overloaded. This warning is that

the control lamp on the center pole head or the receiving unit will flash red.

In addition, the machine will respond in one of the following ways (adjustable in the machine

configuration):

 Only an entry in the error memory.

 Lowering the excitation speed.

 Shutdown of the machine with entry in the error memory.

 Switch-over to slow mode.

6.3.5 Compatec system (optional)

The Compatec display unit is integrated into the protective hood and is located within the operator’s line-

of-sight. The display unit, consisting of eight LEDs that adapt to the lighting conditions, indicates the

relative compaction progress by successively lighting up while driving. When the number of illuminated

LEDs no longer increases, this means that no further compression can be achieved with the machine.

The operator can finish the work and avoid unnecessary passes.

The overload display indicates if the machine is being operated on too hard of a surface. The operator

is notified of this through an alternating flashing of the LED's.

The Compatec system is suitable for all highly compactable and mixed (well graded) soils.

6.3.6 Telematics – Module (optional)

The telematics records parameters such as GPS data and machine data and transmits them to an

Internet portal. The information for each machine can be visualized, documented, and evaluated there.

6.3.7 Compatec system

The Compamatic – System combines the compaction data from the Compatec - Systems with the data

transfer from the Telematics – Modules.

The following data is transmitted to an Internet portal:

 Compression value

 Machine position (GNSS)

 Operating hours

 Machine number (last 4 digits)

 Telematics-Module-Serial Number

 Operating mode

 Machine type

 Time stamp

6.4 Versions

This operator's manual covers the following models:

NOTICE:

The Compatec system only supports soil compression and does not replace the

professional measuring of soil density by an expert.

Versions Description

r Remote start

m Machine protection – installation

c Compatec system

Page is loading ...

Wacker Neuson DPU80rLem770 User manual

Wacker Neuson DPU80rLem770 User manual

Related papers

Other documents