Chief FCA831 Installation guide
- Category
- Wall & ceiling mounts accessories
- Type
- Installation guide
This manual is also suitable for
INSTALLATION INSTRUCTIONS
‘
To Cart/ceiling Mount To Wall Mount
Fusion™ Side Channel Speaker Adapters
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCA831/841
FCA831/841 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight
mounted to
the FCA831/841 does not exceed 10 lbs (4.5 kg)
per side or 20 lbs (9 kg) total if installing to cart/ceiling mount.
If installing to a wall mount, the combined weight cannot
exceed 20 lbs (9 kg) per side or 40 lbs (18 kg) total.
WARNING: Use of this accessory will decrease the weight
capacity of the mount to which it is attached by the combined
weight of the accessory and all components supported by
this accessory! See Figure below for details.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this accessory to support video equipment such as
televisions or computer monitors.
--SAVE THESE INSTRUCTIONS--
(weight capacity of mounting system) minus
(*weight of FCA831/841 bracket + bracket components)
10 lbs (4.5 kg) per side of 20 lbs (9 kg) total
(weight capacity of mounting system) minus
(*weight of FCA831/841 bracket + bracket components)
20 lbs (9 kg) per side of 40 lbs (18 kg) total
*FCA831 brackets weigh 13 lbs (5.9 kg)
*FCA841 brackets weigh15 lbs (6.8 kg)
weight capacity of accessory
weight capacity of accessory
Installation Instructions FCA831/841
3
DIMENSIONS - FCA831
15.8
400.1
.9
22.2
34.4-57.8
(MEDIUM LANDSCAPE MOUNTS)
FUSION WALL MOUNT SETUP
(*)NOTES:
TYPICAL FUSION INTERFACES ARE 0.625" [15.9] DEEP•
CEILING/CART MOUNT SET-UP
.9
22.2
15.8
400.1
36.2-57.6
(MEDIUM LANDSCAPE MOUNTS)
FCA831/841 Installation Instructions
4
DIMENSIONS - FCA841
.9
22.2
15.8
400.1
46.2-77.6
[1173.5-1971.0]
7.0
177.8
22.3
565.7
10° 10°
.4
11.1 *
2.6
66.4
(*)NOTES:
TYPICAL SINGLE DISPLAY MODELS HAVE INTERFACE DEPTHS .5" [12.7]• TYPICAL DUAL DISPLAY MODELS HAVE INTERFACE DEPTHS 1.9" [48.3]• FCA623 DUAL MONITOR INTERFACES ARE 1.4" DEEP [35.6]•
15.8
400.1
.9
22.2
44.8-84.8
[1137.9-2153.9]
7.0
177.8
22.2
563.8
.25-1.1
[6.35-14.30]
1.8
45.6
.7
17.3 *
FUSION WALL MOUNT SETUP
(*)NOTES:
TYPICAL FUSION INTERFACES ARE 0.625" [15.9] DEEP•
Installation Instructions FCA831/841
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
FCA831/841 Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
7/16”
3/16” (included)
1/8” (included)
A (2)
[Speaker bracket]
B (2)
[Rail extension]
C (2)
[Clamp bracket]
E (2)
[Thumb screw] F (4)
[T-slot stud]
G (4)
[Rail bushing]
M (4)
1/4-20 x 1/2” N (4)
#10-24 x 1/2”
R (1)
1/8”
H (12)
1/4-20”
Q (1)
3/16”
D (2)
[Clamp cover]
J (4)
1/4” K (8)
#10 L (6)
#10-24 x 3/8”
P (4)
5/16-18 x 1/2”
Installation Instructions FCA831/841
7
ASSEMBLY AND INSTALLATION
Attaching to Wall Mount
1. Use two 1/4-20 x 1/2” Phillips pan machine screws (M) with
four 1/4” washers (J) or four 10-24 x 1/2” Phillips pan
machine screws (N) with four #10 washers (K) to secure two
speaker brackets (A) to speakers (not included). (See
Figure 1)
Figure 1
2. Use six #10-24 x 3/8” button head cap screws (L) to secure
two speaker brackets (A) to two rail extensions (B). (See
Figure 2)
Figure 2
3. Install four rail bushings (G) onto two rail extensions (B).
(See Figure 3)
4. Install four 5/16-18 x 1/2” button head flange screws (P) to
ends of rail extensions (B). (See Figure 3)
Figure 3
5. Remove end caps from wall mount rails. (See Figure 4)
Figure 4
speakers
(example)
(A) x 2
1
(M) or (N) x 4
(J) or (K) x 4
(speakers not shown
for clarity)
(L) x 6
2
(A) Left side
Right side
(B) x 2
(A)
(G) x 4
3
(P) x 4
4
(B) x 2
5
Fusion Mount
FCA831/841 Installation Instructions
8
6. Install and tighten the thumb screw (E) on each rail
extension (B). (See Figure 5)
Figure 5
7. Slide rail extensions (B) into wall mount rails. (See Figure 6)
8. Tighten the four rail bushings (G) into the wall mount rails.
(See Figure 6)
NOTE: It may be necessary to lift slightly on the rail extensions
in order to tighten the side speaker bushings.
(E) x 2
6
(B) x 2
Figure 6
FUSION Mount
(B)
7
Side Speaker Bushing
for Minimum Extension
Side Speaker Bushing
for Maximum Extension
8
(G)
Installation Instructions FCA831/841
9
Attaching to Cart/Ceiling Mount
1. Use eight 1/4-20 hex nuts (H) to loosely secure four t-slot
studs (F) to two clamp brackets (C). (See Figure 7)
IMPORTANT ! : Do NOT tighten at this time. Leave
enough space between studs and brackets so that studs
can slide into cart extrusion slots. (See Figure 9)
Figure 7
2. Install two clamp brackets (C) onto two rail extensions (B).
(See Figure 8)
3. Install four 5/16-18 x 1/2” button head flange screws (P) to
ends of rail extensions (B). (See Figure 8)
Figure 8
4. Slide t-slot studs (F) into grooves on back of extrusion until
desired mounting positions are reached. (See Figure 9)
Figure 9
5. Tighten four 1/4-20 hex nuts (H) holding t-slot studs (F) to
clamp brackets (C). (See Figure 10)
6. Use four 1/4-20 hex nuts (H) to secure two clamp covers (D)
to two clamp brackets (C). (See Figure 10)
Figure 10
(C) x 2 (H) x 8
(F) x 4
1
2
2
3
(P) x 4
(C) x 2
(B) x 2
4
4
(F) x 4
extrusion
5
(H) x 4
(rear view)
6
(H) x 4
(D) x 2
(C) x 2
FCA831/841 Installation Instructions
10
7. Use four 1/4-20 x 1/2” Phillips pan machine screws (M) with
1/4” washers (J) or four #10-24 x 1/2” Phillips pan machine
screws (N) with four #10 washers (K) to secure two speaker
brackets (A) to speakers (not included). (See Figure 11)
Figure 11
8. Use six #10-24 x 3/8” button head cap screws (L) and four
#10 washers (K) to secure two speaker brackets (A) to two
rail extensions (B). (See Figure 12)
Figure 12
Tilt Adjustment
NOTE: FCA831 and FCA841 mounts are designed to allow for
10° of tilt forward or backward.
NOTE: For cart/ceiling configurations ONLY.
1. Loosen (do NOT remove) upper and lower button head cap
screws (L) holding speaker brackets (A) to rail extensions
(B). (See Figure 13)
2. Tilt speakers forward or backward as desired. (See Figure
13)
3. Tighten upper and lower button head cap screws (L) holding
speaker brackets (A) to rail extensions (B). (See Figure 13)
Figure 13
speakers
(example)
(A) x 2
7
(M) or (N) x 4
(J) or (K) x 4
(K x 2)
(speakers not shown
for clarity)
(L) x 6
8
(B) x 2
(A)
(A)
2
132
10° forward
10° backward
Installation Instructions FCA831/841
11
FCA831/841 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002654 Rev01
2016 Milestone AV Technologies
www.milestone.com
06/16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Chief FCA831 Installation guide
- Category
- Wall & ceiling mounts accessories
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Chief FCA831 Guide d'installation