Donco 1015-3 Assembly Instructions Manual

Donco
Brand
Donco
Model
1015-3
Type
Assembly Instructions Manual

This manual is also suitable for

Donco 1015-3 is a full/full-size mission bunk bed designed to use a full mattress (53 1/2”–54 1/2” x 74–75”) and bunkie board (53 1/2” x 74”). The total thickness must not exceed 9 inches. The surface of the mattress must be at least 5 inches below the upper edge of the guardrails.

Some of its features include:

  • Assembly is required and the manufacturer warns to not tighten screws until completely assembled.
  • The recommended age for the upper bunk is 6 years and older, and it can only accommodate one person at a time.
  • The bed includes 12 slats and a slat kit with spacer tape that should be installed facing up.

Donco 1015-3 is a full/full-size mission bunk bed designed to use a full mattress (53 1/2”–54 1/2” x 74–75”) and bunkie board (53 1/2” x 74”). The total thickness must not exceed 9 inches. The surface of the mattress must be at least 5 inches below the upper edge of the guardrails.

Some of its features include:

  • Assembly is required and the manufacturer warns to not tighten screws until completely assembled.
  • The recommended age for the upper bunk is 6 years and older, and it can only accommodate one person at a time.
  • The bed includes 12 slats and a slat kit with spacer tape that should be installed facing up.
Thank you for purchasing this quality product.
Be sure to check all packing materials carefully
For small parts which may have come loose in-
Side the carton during shipment. Separate,
Identify and count all parts and hardware.
Compare with the parts list to be sure all parts are
present.
“DO NOT TIGHTEN SCREWS
UNTIL COMPLETELY ASSEMBLED”
SAFETY WARNINGS!
1-Follow the information on the warning label appearing on the upper bunk end structure and on the carton.Do
Not remove warning label from bed.
2-Always use the recommended size mattress or mattress support,or both,to help prevent the likelihood
Of entrapment or falls.
3-Surface of mattress must be at least 5 inchess below the upper edge of guardrails.
4-Do not allow children under 6 years of age to use the upper bunk.
5-Prohibit more than one person on upper bunk.
6-Periodically check and ensure that the guardrail,ladder and other components are in their properposi-
Tion,free from damage,and that all connectors are tight.
7-Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8-Always use the ladder for entering and leaving the upper bunk.
9-Do not use substitute parts.Contact distributor or dealer for replacement parts.
10-Use of anight light may provide added safety precaution for a child using the upper bunk.
11-If the bunk bed will be placed next to a wall,the guard rail that runs the full length of the bed should
Be placed against the wall to prevent entrapment between the bed and the wall.
12-Always use guardrails on both long sides of the upper bunk.
13-The use of water or sleep flotation mattresses is prohibited.
14-Keep these instructions for future reference.
15-Strangulation Hazard-Never attach or hang items to any part of the bunk bed that are not designed for
Use with the bed:for example,but not limited to,hooks,belts,and jump ropes,etc.
IMPORTANT: PLEASE READ INSTRUCTIONS BEFORE STARTING THE ASSEMBLY
In t
scto
is
n
u
r
In t
stio
cs
n
ru
ASSEMBLY INSTRUCTIONS
SIZE OF MATTRESS AND FOUNDATION (SUPPORT)
The total thickness must not exceed 9" inchess. Do not use mattress without the proper bunkie board of safe
foundation.
Note:There must beat least inchess from top surface of mattress to top edge or guardrails.
5”
TO OBTAIN PARTS,PLEASE CONTACT:
This bed is designed to use a full mattress (53 ½”-54 ½”x 74-75”) and bunkie board (53 ½“x 74”).
REPLACEMENTPARTS.
Replacement parts,including additional guardrails,may be obtained from place of purchase or original
distributor.
DONCO TRADING COMPANY - FORT WORTH,TEXAS
1015-3 FULL / FULL
MISSION BUNK BED
ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. Be sure to check all packing
material carefully for small parts which may have come loose inside the
carton during shipment. Separate, identify and count all parts and hardware.
Compare with the parts list to be sure all parts are present.
“DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED”
IMPORTANT:
PLEASE READ INSTRUCTION BEFORE STARTING THE ASSEMBLY
(Hammer)
(Phillips Key)
(Not Incluid)(Not Incluid)
2 h
Tool Required
1015-3 FULL FULL
MISSION BUNK BED
Identifying the Hardware/part list-
WARNING LABELS
NOT REMOVE!
14
34 01
Qty
1/4 x 80 Screw
7,0 x 80 Screw
7,0 x 50 Screw
A
D
G
Qty
Qty
Qty
16
06
04
Half Moon
BQty
16
1/4" C
E
H22
Qty
Qty
Qty
F
15 x 100 Wood Dowel 10 x 40 Wood Dowel
Allen Key
4,0 x 30 Screw
Part List: 1015-3 FULL FULL MISSION BUNK BED
36
3,5 x 16 Screw
JQty
- Identify the hardware using the illustrations below.
06
IQty
H
H
H
H
H
H
H
01
H
H
X2
X2
X2
X2
X4
S
E
L
O
H
E
T
I
H
W
L
I
A
R
E
D
I
S
T
N
O
R
F
H
H22
Qty
10 x 40 Wood Dowel
Tool Required
PREDRILLED
MARKS !
02 BOTTOM BED
01
02
Qty
Qty
F
I
Allen Key
1/4 x 80 Screw
AQty
08
Half Moon
BQty
08
1/4"
B
B
A
A
A
F
A
A
A
AF
F
B
08
3,5x16 Screw
JQty
HOLES
J
J
J
J
04
3,5x16 Screw
JQty
JJ
JJ
GQty
04
15 x 100 Wood Dowel
G
G
G
G
I
(Phillips Key)
Tool Required
03
I
I
I
I
I
I
j
j
PREDRILLED
MARKS !
``INSTALL SLAT KIT WITH SPACER
TAPE ON TOP (FACING UP)``
E
SIDE-RAIL
L
SAT
PREDRILLED
MARKS !
E
E
E
E
E
E
E
E
E
E
E
E
B
B
A
A
A
F
F
F
F
F
D
D
D
D
HOLES
A
A
A
A
F
F
I
J
J
J
J
16
3,5x16 Screw
JQty
01
Qty
FAllen Key
1/4 x 80 Screw
AQty
08
Half Moon
BQty
08
1/4"
12
EQty
4,0 x 30 Screw
(Phillips Key)
Tool Required
(Phillips Key)
Tool Required
05
7,0 x 80 Screw
DQty
04
04
Qty
I
TOP BED
PREDRILLED
MARKS !
The first slats must be fixed
here at 3" from each headboard end.
!
!
04
JJ
JJ
07
16
EQty
4,0 x 30 Screw
E
E
EE
E
E
E
E
E
E
E
E
E
E
E
E
08
3,5x16 Screw
JQty
(Phillips Key)
Tool Required
(Phillips Key)
Tool Required
06
I
I
I
I
I
I
j
j
E
SIDE-RAIL
L
SAT
The first slats must be fixed
here at 3" from each headboard end.
!
!
``INSTALL SLAT KIT WITH SPACER
TAPE ON TOP (FACING UP)``
09
08
F
F
F
F
F
F
F
F
C
C
C
C
C
C
C
C
08
7,0x50 Screw
CQty
01
Qty
FAllen Key
Ex3
10
11
01
Qty
FAllen Key
03
EQty
4,0 x 30 Screw
04
7,0x50 Screw
CQty
(Phillips Key)
Tool Required
C
F
7,0x80 Screw
DQty
02
01
Qty
FAllen Key
02
7,0x50 Screw
CQty
C
F
D
F
12
03
EQty
4,0 x 30 Screw
(Phillips Key)
Tool Required
Ex3
In t
scto
is
n
u
r
In t
stio
cs
n
ru
13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Donco 1015-3 Assembly Instructions Manual

Donco
Brand
Donco
Model
1015-3
Type
Assembly Instructions Manual
This manual is also suitable for

Donco 1015-3 is a full/full-size mission bunk bed designed to use a full mattress (53 1/2”–54 1/2” x 74–75”) and bunkie board (53 1/2” x 74”). The total thickness must not exceed 9 inches. The surface of the mattress must be at least 5 inches below the upper edge of the guardrails.

Some of its features include:

  • Assembly is required and the manufacturer warns to not tighten screws until completely assembled.
  • The recommended age for the upper bunk is 6 years and older, and it can only accommodate one person at a time.
  • The bed includes 12 slats and a slat kit with spacer tape that should be installed facing up.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents