dji Assistant 2 (Enterprise Series) User manual

Type
User manual

This manual is also suitable for

v1.0 2021.03
MAVIC 2
ENTERPRISE
Advanced
User Manual
Searching for Keywords
Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe
Acrobat Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to
begin a search.
Navigating to a Topic
View a complete list of topics in the table of contents. Click on a topic to navigate to that
section.
Printing this Document
This document supports high resolution printing.
© 2021 DJI All Rights Reserved.
3
Download DJI Assistant 2 (Enterprise Series)
Download DJI ASSISTANTTM 2 (Enterprise Series) at
http://www.dji.com/mavic-2-enterprise-advanced
Using This Manual
Legend
Warning Important Hints and Tips Reference
Read Before the First Flight
Read the following documents before using the MAVICTM 2 Enterprise Advanced:
1. In the Box
2. User Manual
3. Quick Start Guide
4. Disclaimer and Safety Guidelines
5. Intelligent Flight Battery Safety Guidelines
It is recommended to read the disclaimer and safety guidelines before using for the first time.
Prepare for your rst ight by reviewing the quick start guide and refer to this user manual for more
information.
Download the DJI Pilot App
Make sure to use the DJI Pilot app during ight.* Mavic 2 Enterprise Advanced is only
compatible with the Android version of DJI Pilot and Smart Controller.
Scan the QR code on the right to download the latest version. The Android version of
DJI Pilot is compatible with Android v5.0 and later.
* For increased safety, ight is restricted to a height of 98.4 ft (30 m) and range of 164 ft (50 m) when not connected or
logged into the app during ight. This applies to DJI Pilot and all apps compatible with DJI aircraft.
The operating temperature of this product is -10° to 40° C. It does not meet the standard
operating temperature for military grade applications (-55° to 125° C), which is required to endure
greater environmental variability. Operate the product appropriately and only for applications
where it meets the operating temperature range requirements of that grade.
4
© 2021 DJI All Rights Reserved.
Contents
Using This Manual 3
Legend 3
Read Before the First Flight 3
Download the DJI Pilot App 3
Download DJI Assistant 2 (Enterprise Series) 3
Product Prole 7
Introduction 7
Preparing the Aircraft 7
Preparing the Remote Controller 9
Diagram 10
Activation 13
Aircraft 15
Flight Modes 15
Aircraft LEDs and Status Indicator 16
Return to Home 17
Vision Systems and Infrared Sensing Systems 20
Flight Recorder 23
Password Protection 23
Attaching and Detaching the Propellers 24
Intelligent Flight Battery 25
Gimbal and Camera 28
DJI AirSense 30
Modular Accessories 31
Using the RTK Module 32
Smart Controller 34
Smart Controller Prole 34
Smart Controller Operations 34
Linking the Smart Controller 39
Status LED and Battery Level LEDs Description 40
Smart Controller Warning Sounds 41
© 2021 DJI All Rights Reserved.
5
DJI Pilot App 43
Manual Flight 43
Mission Flight 49
Album 53
Flight 55
Flight Environment Requirements 55
Flight Limits and GEO Zones 55
Pre-Flight Checklist 57
Starting/Stopping the Motors 57
Flight Test 58
Appendix 60
Specications 60
Calibrating the Compass 65
Updating Firmware 66
After-Sales Information 67
6
© 2021 DJI All Rights Reserved.
Product Prole
This section introduces Mavic 2 Enterprise
Advanced and lists the components of the
aircraft and remote controller.
© 2021 DJI All Rights Reserved.
7
Product Prole
Introduction
DJI Mavic 2 Enterprise Advanced features omnidirectional Vision Systems and Infrared Sensing Systems,
and comes with a fully stabilized 3-axis gimbal camera that includes a thermal camera and a visual
camera, providing both infrared and visual images simultaneously. DJI’s Obstacle Sensing technology
helps users to y safely so they can capture complex shots while DJI AirSense provides awareness of the
surrounding airspace and password protection ensures access to the aircraft and all data is secure.
Boasting a fully stabilized 3-axis gimbal camera with a thermal camera and visual camera, Mavic 2
Enterprise Advanced oers infrared and visible light imaging simultaneously. The infrared thermal camera
records 640×512 video, and the visual camera captures 4K videos and 48MP photos. The aircraft
supports up to 32× digital zoom. Using the latest technology to reduce the angular vibration range to
within +0.005, Mavic 2 Enterprise Advanced provides increased stability and footage quality.
Built into the remote controller is DJI’s long-range transmission technology OCUSYNCTM 2.0, oering
a maximum transmission range of 6.2 mi (10 km) and displaying video from the aircraft to DJI Pilot on
a mobile device at up to 720p. The remote controller works at both 2.4 GHz and 5.8 GHz and can
automatically select the best transmission channel without any latency. The aircraft and camera can easily
be controlled using the onboard buttons. The DJI Smart Controller comes with a number of aircraft and
gimbal controls as well as customizable buttons and has a built-in 5.5-inch high-brightness screen. The
remote controller features Bluetooth compatibility, supports GNSS, and can connect to the internet via
Wi-Fi. The detachable control sticks make the remote controller easier to store. The maximum run time is
2.5 hours.
The Mavic 2 Enterprise Advanced boasts a maximum ight speed of 44.7 mph (72 kph) and a maximum
ight time of 31 minutes.
The maximum ight time was tested in an environment with no wind while ying at a consistent
15.5 mph (25 kph) and the maximum ight speed was tested at sea level altitude with no wind.
These values are for reference only.
The remote controller reaches its maximum transmission distance (FCC) in a wide-open area with
no electromagnetic interference at an altitude of about 400 ft (120 m). The maximum runtime was
tested in a laboratory environment. This value is for reference only.
5.8 GHz is not supported in certain regions. Observe local laws and regulations.
Preparing the Aircraft
All aircraft arms are folded before the aircraft is packaged. Follow the steps below to unfold the
aircraft.
1. Remove the gimbal cover from the camera.
2. Unfold the front arms before unfolding the rear arms.
1
2
3
MAVIC 2 ENTERPRISE Advanced User Manual
8
© 2021 DJI All Rights Reserved.
* Attach the gimbal cover when not in use.
1) Hold the gimbal in place and insert the gimbal clamp
between the aircraft and the gimbal.
2) Make sure the hooks on the gimbal protector are
locked in the grooves of the aircraft. Lower the gimbal
protector over the gimbal and secure with the buckle.
The buckle will click when it is securely attached.
3. Attach the propellers with white marks to the motors with white marks. Press the propeller down
onto the motors and turn until it is secure. Attach the unmarked propellers to the unmarked
motors. Unfold all the propeller blades.
1
2
3
4. All Intelligent Flight Batteries are in Hibernation mode before shipping to ensure safety. Use the
provided AC power adapter to charge and activate Intelligent Flight Batteries for the rst time. To
charge an Intelligent Flight Battery after ight, remove from the aircraft and attach to the AC power
adapter.
Grooves Hooks
Gimbal clamp
A
A
Power Outlet
100~240 V
Charging Time:
~1 hour 30 minutes
Unfold the front arms and propellers before unfolding the rear arms.
It is normal for there to be friction on the arms and aircraft due to the folding design of Mavic 2
Enterprise Advanced.
Make sure the gimbal cover is removed and all arms and propellers are unfolded before powering
on the aircraft. Otherwise, it may aect the aircraft’s self-diagnostics.
MAVIC 2 ENTERPRISE Advanced User Manual
© 2021 DJI All Rights Reserved.
9
Preparing the Remote Controller
Two pairs of control sticks are included in the packaging for the Smart Controller. One pair is stored
in the sticks storage slot on the back of the remote controller. Follow the steps below to attach the
control sticks stored in the sticks storage slot to the remote controller.
Lift the antennas Remove the control sticks Rotate to attach
the control sticks
MAVIC 2 ENTERPRISE Advanced User Manual
10
© 2021 DJI All Rights Reserved.
Diagram
Mavic 2 Enterprise Advanced (L1TE)
2
3
1
4
5A
B
6
7
8
9
10
11
12
15
13
16
14
17
18
19
19
21
22
20
1. Forward Vision System
2. Propellers
3. Motors
4. Front LEDs
5. Gimbal and Camera
A. Thermal Camera
B. Visual Camera
6. Antennas
7. Backward Vision System
8. Aircraft Status Indicator
9. Battery Buckles
10. Lateral Vision System
11. USB-C Port
12. Link Button/Linking Status
Indicator
13. Extended Port (can be used to
connect accessories)
14. Extended Port Cover
15. Battery Level LEDs
16. Power Button
17. Intelligent Flight Battery
18. Upward Infrared Sensing
System
19. Downward Vision System
20. microSD Card Slot
21. Downward Infrared Sensing
System
22. Auxiliary Bottom Light (can be
used as a beacon in low light
conditions)
MAVIC 2 ENTERPRISE Advanced User Manual
© 2021 DJI All Rights Reserved.
11
DJI Smart Controller (RM500)
1
69999
1010101010101010101010101010
10
12
10
13
77 8
11
3
24
14 15
5
16
17
18 19 20
21
22
1. Antennas
Relays aircraft control and video signal.
2. Back Button/Function Button
Press once to return to the previous screen
and press twice to go back to the home
screen.
3. Control Sticks
Control the orientation and movement of the
aircraft when the remote controller is linked
to an aircraft.
4. Return to Home (RTH) Button
Press and hold the button to initiate RTH.
The aircraft returns to the last recorded
Home Point. Press again to cancel RTH.
5. Flight Pause Button
Press to make the aircraft brake and hover
in place (only when GPS or Vision System
are available).
6. Flight Mode Switch
Switch between T-mode, P-mode, and
S-mode.
7. Status LED
Indicates the linking status and warnings
when the battery level is low, temperature is
high, or the control sticks are not centered.
8. Battery Level LEDs
Displays the battery level of the remote
controller.
9. 5D Button
The default conguration is listed below. The
conguration can be adjusted in DJI Pilot.
Up: Recenter gimbal/move gimbal downward
Down: Focus switch/metering
Left: Decrease EV value
Right: Increase EV value
10. Power Button
Use to power the remote controller on or o.
When the remote controller is powered on,
press the button to enter sleep mode or to
wake the controller.
11. Conrm Button/Customizable Button C3
When the remote controller is not linked
to an aircraft, press to conrm a selection.
When linked to an aircraft, the button cannot
be used to conrm a selection. The function
of the button when linked to an aircraft can
be customized in DJI Pilot.
12. Touchscreen
Tap to select.
13. USB-C Port
Use to charge or update the remote controller.
14. Microphone
Records audio.
15. Screw Holes
16. Gimbal Dial
Use to control the tilt of the camera.
MAVIC 2 ENTERPRISE Advanced User Manual
12
© 2021 DJI All Rights Reserved.
17. Record Button
Press to start recording video. Press again
to stop recording.
18. HDMI Port
For video output.
19. microSD Card Slot
Use to insert a microSD card.
20. USB-A Port
Use to connect external devices.
21. Focus/Shutter Button
Press once to take photos according to the
mode selected in DJI Pilot.
22. Camera Settings Dial/Gimbal Dial
Turn to adjust the zoom of the camera.
23. Air Vent
Used for heat dissipation. DO NOT cover
the air vent during use.
24. Sticks Storage Slot
Use to store a pair of control sticks.
25. Customizable Button C2
The default configuration is playback. The
conguration can be set in DJI Pilot.
23
27
28
26
24
25
26. Speaker
Outputs sound.
27. Customizable Button C1
The default configuration is center focus.
The conguration can be set in DJI Pilot.
28. Air Intake
Used for heat dissipation. DO NOT cover
the air intake during use.
MAVIC 2 ENTERPRISE Advanced User Manual
© 2021 DJI All Rights Reserved.
13
Activation
Activating the Smart Controller
Internet
The Smart Controller needs to be activated before using it for the rst time. Make sure the
remote controller is connected to the internet during activation. Follow the steps below to
activate.
1. Power on the remote controller. Select the language and tap Next. Carefully read the terms of use
and privacy policy and tap Agree. Set the country/region.
2. Connect the remote controller to the internet via Wi-Fi. After connecting, tap Next to continue and
select the time zone, date, and time.
3. Log in with a DJI account. If you do not have an account, create a DJI account and log in.
4. Tap Activate on the activation page.
5. After activating, select whether to join the Smart Controller Improvement Project. The project helps
to improve the user experience by automatically sending diagnostic and usage data daily. No
personal data will be collected by DJI.
6. The remote controller will check for rmware updates. If a rmware update is available, a prompt
will appear to download the latest version.
Check the internet connection if the activation fails. If the internet connection is normal, try to activate
the remote controller again. If the issue persists, contact DJI.
Activating the Aircraft
Mavic 2 Enterprise Advanced requires activation before using it for the rst time. Follow the onscreen
instructions to activate Mavic 2 Enterprise Advanced using DJI Pilot.
14
© 2021 DJI All Rights Reserved.
Aircraft
This section introduces the flight controller,
Intelligent Flight Battery, and the Forward,
Backward, and Downward Vision Systems.
© 2021 DJI All Rights Reserved.
15
Aircraft
Mavic 2 Enterprise Advanced contains a flight controller, vision systems, video downlink system,
propulsion system, and an Intelligent Flight Battery. Refer to the aircraft diagram in the Product Prole
section.
Flight Modes
Mavic 2 Enterprise Advanced has three flight modes, plus a fourth flight mode that the aircraft
switches to in certain circumstances:
P-mode (Positioning): P-mode works best when the GPS signal is strong. The aircraft utilizes GPS
and the Vision Systems to locate itself, stabilize, and navigate between obstacles. When the Forward
and Backward Vision Systems are enabled and lighting conditions are sufficient, the maximum
ight altitude angle is 25°, the maximum forward ight speed is 31 mph (50 kph), and the maximum
backward ight speed is 27 mph (43 kph). Note: P-mode requires larger stick movements to achieve
high speeds. The aircraft automatically changes to Attitude (ATTI) mode when the Vision Systems are
unavailable or disabled and when the GPS signal is weak or the compass experiences interference.
When the Vision Systems are unavailable, the aircraft cannot position itself or brake automatically,
which increases the risk of potential ight hazards. In ATTI mode, the aircraft may be more easily
affected by its surroundings. Environmental factors such as wind can result in horizontal shifting,
which may present hazards, especially when ying in conned spaces.
S-mode (Sport): In S-mode, Obstacle Sensing is disabled and the aircraft uses GPS and the Vision
Systems for positioning. The maximum ight speed is 44.7 mph (72kph). The aircraft cannot sense
or avoid obstacles. Note: In S-mode, aircraft responses are optimized for agility and speed making it
more responsive to stick movements.
T-mode (Tripod): T-mode is based on P-mode and the ight speed is limited, which makes the aircraft
more stable during shooting. The maximum ight, ascent, and descent speeds are limited to 1 m/s.
Obstacle Sensing and the Upward Infrared Sensing System are disabled in S-mode, which means
the aircraft cannot sense obstacles on its route automatically.
The maximum speed of the aircraft and braking distance significantly increase in S-mode. A
minimum braking distance of 98.4 ft (30 m) is required in windless conditions.
Descent speed signicantly increases in S-mode.
The responsiveness of the aircraft signicantly increases in S-mode, which means a small stick
movement on the remote controller translates into the aircraft moving a large distance. Pay attention
and maintain adequate maneuvering space during ight.
Use the ight mode switch on the remote controller to switch between ight modes. To switch ight
modes, rst go to camera view in DJI Pliot, tap and enable Multiple Flight Modes.
MAVIC 2 ENTERPRISE Advanced User Manual
16
© 2021 DJI All Rights Reserved.
The Front LEDs show the orientation of the aircraft and glow solid red when the aircraft is powered on
to indicate the front of the aircraft. Go to settings in DJI Pilot to turn the Front LEDs on or o.
The Aircraft Status Indicators communicate the status of the ight control system of the aircraft. Refer to
the table below for more information about the Aircraft Status Indicators. The Aircraft Status Indicators
also ash when the Home Point is being recorded as described in the Return to Home section.
Aircraft LEDs and Status Indicator
Mavic 2 Enterprise Advanced has Front LEDs and Aircraft Status Indicators as shown in the gure below.
Aircraft Status Indicator States
Normal States
Blinks red, green, and yellow
continuously
Powering on and performing self-diagnostic
tests
Blinks yellow and green alternately Warming up
Blinks green slowly P-mode with GPS
×2 Blinks green twice continuously P-mode with Forward and Downward Vision
Systems
Blinks yellow slowly No GPS, Forward Vision System, or
Downward Vision System
Blinks green quickly Braking
Blinks green and blue alternately RTK enabled and RTK data is being used
Warning States
Blinks yellow quickly Remote controller signal lost
Blinks red slowly Low battery
Blinks red quickly Critically low battery
Blinks red IMU error
Solid red Critical error
Blinks red and yellow alternately Compass calibration required
Blinks red and green alternately RTK enabled but RTK data unavailable
For missions that require concealed ight, enter common settings in DJI Pilot and select LED Settings
and turn the Frame Arm LEDs o.
Aircraft Status Indicator
Front LEDs
Aircraft Status Indicator
Front LEDs
MAVIC 2 ENTERPRISE Advanced User Manual
© 2021 DJI All Rights Reserved.
17
GPS Description
Home
Point
If a strong GPS signal was acquired before takeoff, the Home Point is
the location from which the aircraft launched. The GPS signal strength is
indicated by the GPS icon ( ). The Aircraft Status Indicator will blink
green quickly when the Home Point is recorded.
Smart RTH
If the GPS signal is suciently strong, Smart RTH can be used to bring the aircraft back to the Home
Point. Smart RTH is initiated by pressing and holding the RTH button on the remote controller. Exit
Smart RTH by pressing the RTH button on the remote controller.
Low Battery RTH
Low Battery RTH is triggered when the Intelligent Flight Battery is depleted to the point that the safe
return of the aircraft may be aected. Return home or land the aircraft immediately when prompted.
DJI Pilot displays a warning prompt when the battery level is low. The aircraft will automatically return
to the Home Point if no action is taken after a 10 second countdown.
The user can cancel RTH by pressing the RTH button or ight pause button on the remote controller.
If RTH is cancelled following a low battery level warning, the Intelligent Flight Battery may not have
enough power for the aircraft to land safely, which may lead to the aircraft crashing or being lost. The
thresholds for the battery level warnings are automatically determined based on the current altitude of
the aircraft and distance from the Home Point.
The aircraft will land automatically if the current battery level can only support the aircraft long enough
to descend from its current altitude. The user cannot cancel the auto landing but can use the remote
controller to alter the orientation of the aircraft during the landing process.
Return to Home
Return to Home (RTH) brings the aircraft back to the last recorded Home Point. There are three
types of RTH: Smart RTH, Low Battery RTH, and Failsafe RTH. This section describes these three
scenarios in detail.
DJI Pilot Battery Level Indicator Bar
Critically low battery level warning (Red)
Low battery level warning
(Yellow)
Battery level is sucient (Green)
Remaining ight time
Charge required to
return to Home Point
12:29
MAVIC 2 ENTERPRISE Advanced User Manual
18
© 2021 DJI All Rights Reserved.
Warning Scenario Aircraft Status
Indicator DJI Pilot App Actions
Low
Battery
Level
Remaining battery level
supports RTH.
Blinks red slowly
Choose RTH or
resume normal
ight.
Select an option. If no
action is taken, the aircraft
will enter RTH.
Remaining battery level
supports Emergency
RTH (when in RTH, with a
normal remote controller
signal, and at an altitude
higher than 50 m).
Choose
Emergency RTH
or resume RTH.
Select an option.
Emergency RTH (aircraft
descends to 50 m and
returns to the Home Point)
or resume RTH (aircraft
ies to Home Point without
descending). If no action is
taken, the aircraft will enter
Emergency RTH.
Remaining battery level
supports Emergency
Landing (when in RTH
with a normal remote
controller signal).
Aircraft lands.
Action cannot be
canceled.
Aircraft lands immediately.
Critically
Low
Battery
Level
Aircraft lands after 10
seconds (when ying
normally with a critical
low battery level).
Blinks red quickly
Aircraft lands
after 10 seconds.
Action cannot be
canceled.
Aircraft lands after 10
seconds.
Aircraft lands
automatically (when
ying normally with an
extremely critical low
battery level).
Aircraft lands
immediately.
Action cannot be
canceled.
Aircraft lands immediately.
Failsafe RTH
The Forward Vision System allows the aircraft to create a real-time map of its ight route as it ies.
If the Home Point was successfully recorded and the compass is functioning normally, Failsafe RTH
automatically activates after the remote controller signal is lost for more than two seconds.
When Failsafe RTH is activated, the aircraft starts to retrace its original ight route home. If the remote
control signal is re-established within 60 seconds of Failsafe RTH being activated, the aircraft hovers at
its present location for 10 seconds and waits for pilot commands. Press the RTH button on the remote
controller to cancel Failsafe RTH and retake control. If no pilot command is given, the aircraft ies to the
Home Point in a straight line. If the remote control signal is still lost 60 seconds after activating Failsafe
RTH, the aircraft stops retracing its original ight route and ies to the Home Point in a straight line.
RTH Procedure
1. The aircraft adjusts its orientation.
2. a. If the aircraft is further than 20 m from the Home Point when RTH begins, it ascends to the
pre-set RTH altitude and flies to the Home Point at a speed of 12 m/s. If the current altitude
is higher than the RTH altitude, the aircraft flies to the Home Point at the current altitude.
Forward and Backward Vision Systems are enabled.
MAVIC 2 ENTERPRISE Advanced User Manual
© 2021 DJI All Rights Reserved.
19
RTH Illustration
Obstacle Avoidance During RTH
Provided that lighting conditions are sufficient for the Forward and Backward Vision Systems to
operate, the aircraft senses and actively attempts to avoid obstacles during RTH. The obstacle
avoidance procedure is as follows:
1. The aircraft decelerates when an obstacle is sensed.
2. The aircraft stops and hovers and then ascends until no obstacle is sensed.
3. The RTH procedure resumes and the aircraft ies to the Home Point at the new altitude.
The aircraft cannot return to the Home Point if the GPS signal is weak or unavailable.
In Smart RTH and Low Battery RTH, the aircraft automatically ascends to an altitude of 65 ft
(20 m). Once the altitude is 65 ft (20 m) or higher, move the throttle stick to make the aircraft
stop ascending and fly to the Home Point at its current altitude.
The aircraft cannot avoid obstacles during Failsafe RTH if the Forward and Backward Vision
Systems are unavailable. It is important to set a suitable RTH Altitude before each ight. To set the
RTH altitude, open DJI Pilot, and tap .
During RTH, the orientation and direction of the aircraft cannot be controlled, but the remote
controller or DJI Pilot can be used to control the speed and altitude.
During RTH, obstacles on either side of the aircraft cannot be detected or avoided.
b. If the aircraft is between 5 and 20 m from the Home Point when RTH is initiated, the aircraft
flies back at the current altitude. If the current altitude is less than 2 m, the aircraft will first
ascend to 2 m and fly to the Home Point at a speed of 3 m/s. If RTH at Current Altitude is
disabled, the aircraft lands immediately.
c. If the aircraft is less than 5 m from the Home Point when RTH is initiated, it lands immediately.
3. After reaching the Home Point, the aircraft lands and the motors stop.
1 Record Home Point 2 Conrming Home Point
4 Signal Lost for Extended Time
×
5
RTH (adjustable altitude)
Height over HP > Failsafe Altitude
Elevate to Failsafe Altitude
Height over HP≤Failsafe Altitude
Failsafe Altitude
×
6 Landing
×
3 Remote Controller Signal Lost
×
MAVIC 2 ENTERPRISE Advanced User Manual
20
© 2021 DJI All Rights Reserved.
Landing Protection
Landing Protection is activated during Smart RTH and the aircraft performs as follows:
1. When Landing Protection determines that the ground is suitable for landing, the aircraft lands gently.
2. If the ground is not suitable for landing, the aircraft hovers and waits for the pilot to conrm if it is
suitable for landing or not.
3. If Landing Protection is not operational, DJI Pilot displays a landing prompt when the aircraft
descends below 0.5 m. To land the aircraft, push the throttle stick down for one second or use the
auto landing slider in DJI Pilot.
Landing Protection is active during Low Battery RTH and Failsafe RTH. The aircraft performs as follows:
During Low Battery RTH and Failsafe RTH, the aircraft hovers 2 m above the ground and waits for the pilot to
conrm it is suitable to land. To land the aircraft, push the throttle stick down for one second or use the auto
landing slider in the app. Landing Protection activates and the aircraft performs the steps listed above.
Vision Systems are disabled during landing. Make sure to land the aircraft with caution. Use caution
when landing the aircraft.
Precision Landing
Mavic 2 Enterprise Advanced automatically scans and attempts to match the terrain features
underneath the aircraft during RTH. When the current terrain matches the Home Point terrain, the
aircraft will start landing. A prompt will appear in DJI Pilot if the aircraft is unable to match the terrain.
Landing protection is available during precision landing.
The performance of Precision Landing is subject to the following conditions:
a) The Home Point must be recorded upon takeoff and must not be changed during flight.
Otherwise, the aircraft will have no record of the terrain features of the Home Point.
b) During takeo, the aircraft must ascend at least 7 m before moving horizontally.
c) The Home Point terrain features must remain largely unchanged.
d) The Home Point terrain features must be distinguishable.
e) The lighting conditions must not be too light or too dark.
The following actions are available during Precision Landing:
a) Press the throttle stick down to accelerate landing.
b) Move the control sticks in any other direction to stop Precision Landing. The aircraft will descend
vertically after the control sticks are released.
Vision Systems and Infrared Sensing Systems
Mavic 2 Enterprise Advanced is equipped with Forward, Backward, Downward, and Lateral Vision
Systems, and Upward and Downward Infrared Sensing Systems. They provide the aircraft with
omnidirectional obstacle sensing if lighting conditions are adequate.
The main components of the Forward, Backward, and Downward Vision Systems are six cameras
located on the front, back, and bottom of the aircraft. The Lateral Vision Systems are two cameras
located on either side of the aircraft. The main components of the Upward and Downward Infrared
Sensing Systems are two 3D infrared modules located on the top and bottom of the aircraft.
The Downward Vision System and Infrared Sensing System helps the aircraft maintain its current
position and hover in place more precisely and to y indoors or in other environments where a GPS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

dji Assistant 2 (Enterprise Series) User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI