Humandata XCM-107-50T User manual

Brand
Humandata
Model
XCM-107-50T
Type
User manual

This manual is also suitable for

HuMANDATA LTD.
Virtex-5 FPGA Board
XCM-107 Series
User’s Manual
Ver. 1
.0
Table of Contents
Table of ContentsTable of Contents
Table of Contents
Revision History
Revision HistoryRevision History
Revision History
................................
................................................................
................................................................
................................................................
................................................................
................................................................
.................................
..
.
1
11
1
Introduction
IntroductionIntroduction
Introduction
................................
................................................................
................................................................
................................................................
................................................................
................................................................
........................................
................
........
1
11
1
1. Specifications
1. Specifications1. Specifications
1. Specifications
................................
................................................................
................................................................
................................................................
................................................................
................................................................
.........................................
..................
.........
2
22
2
2. Overview
2. Overview2. Overview
2. Overview
................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................
................................
................
3
33
3
2.1. Name of Parts ...................................................................................................... 3
2.2. Block Diagram ..................................................................................................... 4
2.3. Power Supply ....................................................................................................... 5
2.4. Clock ..................................................................................................................... 5
2.5. JTAG Connector .................................................................................................. 5
2.6. Configuration Switch .......................................................................................... 6
3. Develop
3. Develop3. Develop
3. Development Environment
ment Environmentment Environment
ment Environment
................................
................................................................
................................................................
................................................................
...................................................
......................................
...................
6
66
6
4. Configuration
4. Configuration4. Configuration
4. Configuration
................................
................................................................
................................................................
................................................................
................................................................
................................................................
.........................................
..................
.........
7
77
7
4.1. FPGA Configuration by JTAG............................................................................ 7
4.2. Generate programming file ................................................................................ 8
4.3. Program the Configuration Device .................................................................... 9
4.4. FPGA Configuration by Configuration Device ................................................ 10
4.5. Configuration Rate............................................................................................ 10
5. Additional Documentation and User Support
5. Additional Documentation and User Support5. Additional Documentation and User Support
5. Additional Documentation and User Support
................................
................................................................
......................................................
............................................
......................
11
1111
11
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
4. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
5. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
6. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
7. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
8. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
9. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
10. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
11. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
12. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
13. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
XCM
-
107 (Ver.1
.0)
Revision History
Revision HistoryRevision History
Revision History
Date
DateDate
Date
Version
VersionVersion
Version
Description
DescriptionDescription
Description
Feb. 15, 2010
1.0 Initial release.
Introduction
IntroductionIntroduction
Introduction
Thank you for buying our product XCM-107 series.
This is an evaluation board equipped with a Xilinx FPGA Virtex-5 LXT, power,
reset, and clock circuit.
It can provide you with very convenient and easy-to-use environment.
2
XCM
-
107 (Ver.1
.0)
1.
1.1.
1. Specifications
SpecificationsSpecifications
Specifications
Model Name
Model NameModel Name
Model Name
XCM-107-30T XCM-107-50T
FPGA
FPGAFPGA
FPGA
XC5VLX30T-1FFG665C XC5VLX50T-1FFG665C
Power Input
Power InputPower Input
Power Input
DC 3.3 [V]
Config. Device
Config. DeviceConfig. Device
Config. Device
M25P16-VMF6P (STMicro, 16Mbit) *
**
*
Dimensions
DimensionsDimensions
Dimensions
1.693" x 2.126" (43 x 54 [mm])
Weight
WeightWeight
Weight
25 [g] typ.
User I/O
User I/OUser I/O
User I/Os
ss
s
128
User I/O Connectors
User I/O ConnectorsUser I/O Connectors
User I/O Connectors
FX10A-80P/8-SV1 (71) (HIROSE)
User Switch
User SwitchUser Switch
User Switch
1
User LEDs
User LEDsUser LEDs
User LEDs
2
On
OnOn
On-
--
-Board Clock
Board ClockBoard Clock
Board Clock
50 [MHz], 30 [MHz] (External inputs are available) *
**
*
Diff. Clock
Diff. ClockDiff. Clock
Diff. Clock
125 [MHz], 150 [MHz] (for RocketIO)
Status LEDs
Status LEDsStatus LEDs
Status LEDs
2 : POWER (Red), DONE (Blue) *
**
*
Po
PoPo
Power
werwer
wer-
--
-On Reset
On ResetOn Reset
On Reset
240 [ms] typ. (Configuration reset signal) *
**
*
JTAG Connector
JTAG ConnectorJTAG Connector
JTAG Connector
SIL 7-pin socket, 2.54 [mm] pitch
PCB
PCBPCB
PCB
8 Layer FR-4 t1.6 [mm] Immersion gold
Accessories
AccessoriesAccessories
Accessories
SIL 7-pin header (Mounted) *
**
*
FX10A-80S/8-SV (71) x2 *
**
*
RoHS Compliance
RoHS ComplianceRoHS Compliance
RoHS Compliance
YES
* There may
* There may* There may
* There may
be cases when compatible parts are used.
be cases when compatible parts are used.be cases when compatible parts are used.
be cases when compatible parts are used.
3
XCM
-
107 (Ver.1
.0)
2.
2.2.
2. Overview
OverviewOverview
Overview
2.1.
2.1.2.1.
2.1. Name of Parts
Name of PartsName of Parts
Name of Parts
Component Side
Solder Side
User Switch
Diff
. Clock
125 MHz
150 MHz
Status LED
Done (Blue)
Power (Red)
Config. Switch
User I/O (
CN
A)
Power Circuit
JTAG
Oscillator
30 MHz
50 MHz
User LED
Config. ROM
User I/O (
CN
B)
4
XCM
-
107 (Ver.1
.0)
2.2.
2.2.2.2.
2.2. Block
Block Block
Block Diagram
DiagramDiagram
Diagram
Virtex-5
Virtex-5Virtex-5
Virtex-5
XC5VLX50T/30T
XC5VLX50T/30TXC5VLX50T/30T
XC5VLX50T/30T
-1FFG665C
-1FFG665C-1FFG665C
-1FFG665C
JTAG
JTAG
JTAG
JTAG
Power LED (3.3V)
Power LED (3.3V)Power LED (3.3V)
Power LED (3.3V)
DONE LED
DONE LEDDONE LED
DONE LED
VIO(B) INPUT
VIO(B) INPUTVIO(B) INPUT
VIO(B) INPUT
3.3 V INPUT
3.3 V INPUT3.3 V INPUT
3.3 V INPUT
JTAG
JTAGJTAG
JTAG
Buffer
BufferBuffer
Buffer
64 GPIO
64 GPIO64 GPIO
64 GPIO
User LEDs
User LEDsUser LEDs
User LEDs
Oscillator
OscillatorOscillator
Oscillator
50MHz, 30MHz
50MHz, 30MHz50MHz, 30MHz
50MHz, 30MHz
Power Circuit
Power CircuitPower Circuit
Power Circuit
2.5V, 1.2V, 1.0V
2.5V, 1.2V, 1.0V2.5V, 1.2V, 1.0V
2.5V, 1.2V, 1.0V
2
22
2
MUX
MUXMUX
MUX
Config. Switch
Config. SwitchConfig. Switch
Config. Switch
RocketIO Diff. CLK
RocketIO Diff. CLKRocketIO Diff. CLK
RocketIO Diff. CLK
125MHz, 150MHz
125MHz, 150MHz125MHz, 150MHz
125MHz, 150MHz
Power-on Reset
Power-on ResetPower-on Reset
Power-on Reset
Typ. 240 ms
Typ. 240 msTyp. 240 ms
Typ. 240 ms
Config. Device
Config. DeviceConfig. Device
Config. Device
M25P16 (16Mb)
M25P16 (16Mb)M25P16 (16Mb)
M25P16 (16Mb)
RocketIO Tx Pair
RocketIO Tx PairRocketIO Tx Pair
RocketIO Tx Pair
User Switch
User SwitchUser Switch
User Switch
External CLK (option)
External CLK (option)External CLK (option)
External CLK (option)
User I/Os CNB
User I/Os CNBUser I/Os CNB
User I/Os CNB
RocketIO Rx Pair
RocketIO Rx PairRocketIO Rx Pair
RocketIO Rx Pair
64 GPIO
64 GPIO64 GPIO
64 GPIO
RocketIO Tx Pair
RocketIO Tx PairRocketIO Tx Pair
RocketIO Tx Pair
User I/Os CNA
User I/Os CNAUser I/Os CNA
User I/Os CNA
RocketIO Rx Pair
RocketIO Rx PairRocketIO Rx Pair
RocketIO Rx PairExternal CLK (option)
External CLK (option)External CLK (option)
External CLK (option)
5
XCM
-
107 (Ver.1
.0)
2.3.
2.3.2.3.
2.3. Power Supply
Power SupplyPower Supply
Power Supply
This board operates from external 3.3 [V] input. You can use CNA and CNB to
input external power. The external power supply should be sufficient and
stabilized.
Internally required 2.5[V], 1.2[V] and 1.0[V] are generated by on-boarded
regulators.
2.4.
2.4.2.4.
2.4. Clock
ClockClock
Clock
You can use 30[MHz] and 50[MHz] on-board oscillator. You can use 125[MHz] and
150[MHz] differential clock for RocketIO reference clock. You can input external
clock by CNA and CNB.
2.5.
2.5.2.5.
2.5. JTAG Connector
JTAG ConnectorJTAG Connector
JTAG Connector
This connector is used to configure the FPGA and program the internal
configuration device in-system. Pin assignment is as follows.
Signal Name
Signal NameSignal Name
Signal Name
Direction
DirectionDirection
Direction
JTAG Pin
JTAG PinJTAG Pin
JTAG Pin
GND I/O 1
TCK IN 2
TDO OUT 3
TMS IN 4
VCC(3.3V) OUT(POW) 5
TDI IN 6
GND I/O 7
1
11
1
2
22
2
3
33
3
4
44
4
5
55
5
6
66
6
7
77
7
6
XCM
-
107 (Ver.1
.0)
2.6.
2.6.2.6.
2.6. Configuration Switch
Configuration SwitchConfiguration Switch
Configuration Switch
The specification of configuration switch is below. “ON” means “Low (Ground)”.
SW1
No.
No.No.
No. 1
11
1
2
22
2
3
33
3
4
44
4
5
55
5
6
66
6
7
77
7
8
88
8
Net Label
Net LabelNet Label
Net Label
X_PROG X_M0
X_M1
X_M2
HSWAP_EN
FS2 FS1 FS0
Default
DefaultDefault
Default
OFF OFF
OFF
OFF
OFF OFF
OFF
OFF
Function
FunctionFunction
Function
Target sel.
Mode Select I/O pull-up SPI variant sel
Master
Master Master
Master SPI
SPISPI
SPI
Slave Serial
Slave SerialSlave Serial
Slave Serial
JTAG
JTAGJTAG
JTAG
X_M[ 0..2]
X_M[ 0..2]X_M[ 0..2]
X_M[ 0..2]
1 : 0 : 0 1 : 1 : 1 1 : 0 : 1
X_PROG
X_PROGX_PROG
X_PROG
Select JTAG access target.
ON : Configuration device
OFF : FPGA
M2, M1, M0
M2, M1, M0M2, M1, M0
M2, M1, M0
Configuration mode setting. The modes showed above are compartment.
HSWAP_EN
HSWAP_ENHSWAP_EN
HSWAP_EN
I/O pull-up control during configuration.
ON : pull-up
OFF : 3-stated.
FS0, FS1, FS2
FS0, FS1, FS2FS0, FS1, FS2
FS0, FS1, FS2
SPI variant select pins.
3.
3.3.
3. Development Environment
Development EnvironmentDevelopment Environment
Development Environment
To develop and design FPGA internal circuit, you need to prepare circuit editor,
HDL editor or logic synthesis tool. These tools are provided by XILINX as ISE.
When you use them, you need an internet license. The version of ISE when
XCM-107 developed is Ver.10.1.03.
ON
: LOW
(0)
OFF : HIGH (1)
7
XCM
-
107 (Ver.1
.0)
4.
4.4.
4. Configurati
ConfiguratiConfigurati
Configuration
onon
on
4.1.
4.1.4.1.
4.1. FP
FPFP
FPG
GG
GA
AA
A
Configuration
ConfigurationConfiguration
Configuration
by JTAG
by JTAGby JTAG
by JTAG
To configure the FPGA by JTAG, please set configuration switch (SW1) as below
and refer to following steps.
SW1
1
11
1
2
22
2
3
33
3
4
44
4
5
55
5
6
66
6
7
77
7
8
88
8
ON
ONON
ON
■
X X X X
OFF
OFFOFF
OFF
■
■
■
X X X X
X: Don’t Care
1. Run iMPACT. Click [Operations]-[Initialize Chain].
2. Select a bit file.
3. Select the device icon, click [Operations]-[Program…].
4. A message “Program Succeeded” would be displayed.
8
XCM
-
107 (Ver.1
.0)
4.2.
4.2.4.2.
4.2. Generate programming fil
Generate programming filGenerate programming fil
Generate programming file
ee
e
To generate an MCS PROM file, please refer to following steps.
1. Double-click “PROM File Formatter” in iMPACT menu.
2. Select “3rd-Party SPI PROM” as the Target.
3. Choose “16M” as SPI PROM Density.
4. Select the bit file you want to convert.
5. Double-click “Generate File…” in iMPACT Processes tab.
6. A message “PROM File Generation Succeeded” will be displayed.
9
XCM
-
107 (Ver.1
.0)
4.3.
4.3.4.3.
4.3. Program
ProgramProgram
Program
the Configuration Device
the Configuration Devicethe Configuration Device
the Configuration Device
When you program the configuration device, you need to set configuration switch
(SW1) as below.
SW1
1
11
1
2
22
2
3
33
3
4
44
4
5
55
5
6
66
6
7
77
7
8
88
8
ON
ONON
ON
■
■
■
X X X X
OFF
OFFOFF
OFF
■
X X X X
X: Don’t Care
1. Double-click [Direct SPI Configuration].
2. Select [Add SPI Device…] from right-click menu.
3. Select the mcs file.
4. Select “M25P16” as part name.
5. Check [Verify] and [Erase Before Programming], then click [OK].
6. Select the device icon, then click [Operations]-[Program…].
7. A message “Program Succeeded” will be displayed.
10
XCM
-
107 (Ver.1
.0)
4.4.
4.4.4.4.
4.4.
FPGA Configuration by Configuration Device
FPGA Configuration by Configuration DeviceFPGA Configuration by Configuration Device
FPGA Configuration by Configuration Device
To configure the FPGA by configuration device, set the configuration switch (SW1)
as below. The FPGA will be configured at next power-on process.
SW1
1
11
1
2
22
2
3
33
3
4
44
4
5
55
5
6
66
6
7
77
7
8
88
8
ON
ONON
ON
■
■
X X X X
OFF
OFFOFF
OFF
■
■
X X X X
X: Don’t Care
4.5.
4.5.4.5.
4.5. Configuration Rate
Configuration RateConfiguration Rate
Configuration Rate
You can change configuration speed by following steps.
1. Right-click [Generate Programming File] then click [Properties…].
2. You can change [Configuration Rate] in [Configuration Options] menu.
11
XCM
-
107 (Ver.1
.0)
5.
5.5.
5. Additional Documentation and User Support
Additional Documentation and User SupportAdditional Documentation and User Support
Additional Documentation and User Support
The following documents and other supports are available at
http://www.hdl.co.jp/en/
http://www.hdl.co.jp/en/http://www.hdl.co.jp/en/
http://www.hdl.co.jp/en/spc/XCM/xcm
spc/XCM/xcmspc/XCM/xcm
spc/XCM/xcm-
--
-107/
107/107/
107/
Circuit Schematic
Pin List
Dimensional drawing
PCB drawing
Net List
… and more.
Virtex
VirtexVirtex
Virtex-
--
-5
5 5
5 FPGA Board
FPGA BoardFPGA Board
FPGA Board
XCM-107 Series
User’s Manual
Ver.
Ver. Ver.
Ver. 1
11
1.0
.0 .0
.0
................................
................................................................
.............................................
..........................
.............
Feb. 15
Feb. 15Feb. 15
Feb. 15, 2010
, 2010, 2010
, 2010
HuMANDATA LTD.
HuMANDATA LTD.HuMANDATA LTD.
HuMANDATA LTD.
Address: 1-2-10-2F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-(0)72-620-2002 (Japanese)
Fax: 81-(0)72-620-2003 (Japanese/English)
URL: http://www.hdl.co.jp/en/ (Global)
http://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Humandata XCM-107-50T User manual

Brand
Humandata
Model
XCM-107-50T
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers