Electrolux EFP60271X User manual

Page is loading ...

EN

2

Instructions Manual

INDEX

RECOMMENDATIONS AND SUGGESTIONS......................................................................................................................6

CHARACTERISTICS..............................................................................................................................................................7

INSTALLATION......................................................................................................................................................................8

USE.......................................................................................................................................................................................10

MAINTENANCE....................................................................................................................................................................12

FR

3

Manuel d’Instructions

SOMMAIRE

CONSEILS ET SUGGESTIONS ..........................................................................................................................................14

CARACTERISTIQUES.........................................................................................................................................................15

INSTALLATION....................................................................................................................................................................16

UTILISATION........................................................................................................................................................................18

ENTRETIEN..........................................................................................................................................................................20

Page is loading ...

EN

6

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages resulting

from incorrect or improper installation.

• The minimum safety distance between the cooker top and the extrac-

tor hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply guaran-

tees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum

diameter 120 mm. The route of the flue must be as short as possible.

• Do not connect the extractor hood to exhaust ducts carrying combus-

tion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances

(e.g. gas burning appliances), a sufficient degree of aeration must be

guaranteed in the room in order to prevent the backflow of exhaust

gas. The kitchen must have an opening communicating directly with

the open air in order to guarantee the entry of clean air.

USE

• The extractor hood has been designed exclusively for domestic use to

eliminate kitchen smells.

• Never use the hood for purposes other than for which it has ben de-

signed.

• Never leave high naked flames under the hood when it is in operation.

• Adjust the flame intensity to direct it onto the bottom of the pan only,

making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use: over-

heated oil can burst into flames.

• Do not flambè under the range hood; risk of fire

• The hood should not be used by children or persons not instructed in

its correct use.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carry-

ing out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

650 mm min.

EN

7

CHARACTERISTICS

Dimensions

Components

Ref. Q.ty Product Components

1 1 Hood Body, complete with: Controls, Light, Blower,

Filters

8 1 Directional Air Outlet grille

9 1 Flange ø 150 mm

10a 1 Flange ø 120 mm

10b 1 Adapting ring ø 120-125 mm

20 1 Closing element

Ref. Q.ty Installation Components

12a 4 Screws 3,5 x 16

12e 2 Screws 2,9 x 12,7

12f 5 Screws 2,9 x 9,5

Q.ty Documentation

1 Instruction Manual

12e

8

9

1

12a

20

12f

10a

10b

EN

8

INSTALLATION

Drilling the Support surface and Fitting the Hood

• The Hood can be fitted directly on the

lower surface of the Wall Units (650 mm

min. above the Cooker Top) using the snap-

on Side Supports.

• Make an opening on the lower surface of

the Wall Unit, as indicated. (fig.1)

• Before carrying out the installation, the

wooden transportation protections screwed

on the visor and on the canopy body must

be removed. (fig.2)

• Choose the correct flange measure basing

on the air outlet diameter and insert it to the

upper air outlet opening. (fig.3)

• Screw the closing profile 20 onto the rear

part of the hood, using the screws 12f (2.9

x 9.5) provided. (fig.4)

• Open the sliding suction panel.

• Remove the metal grease filters one by one

after having disconnected the relative fas-

tening elements.

• Close the sliding suction panel again.

• Insert the Hood until the snap-on side sup-

ports click into place. (fig.5)

• Open the sliding suction panel.

• Lock in position by tightening the screws

Vf from underneath the Hood. (fig.5)

• If necessary, adjust the whole filter holder

unit and proceed as follows:

• Loosen the four adjustment screws Vr

and close the sliding panel again. (fig.6)

• Move the entire filter holder unit until it

is properly aligned with the wall unit.

(fig.7)

• Keeping the hood canopy still, remove

the sliding panel and lock the adjustment

screws again. (fig.6)

• The hood can now be fastened to the

wall unit using the four screws 12a (3.5

x 16) provided. (fig.8)

• Replace the metal grease filters.

• Close the sliding suction panel again.

523

162

1

2

9

10a

10b

3

5

Vr

6

7

12a

8

4

EN

9

Connections

DUCTING VERSION AIR EXHAUST SYSTEM

When installing the hood in ducting version, a rigid or a

flexible pipe with the diameter corresponding to the

flange diameter is used in order to connect the hood to

the air outlet piping.

• Fix the pipe with an adequate quantity of pipe

clamps (not supplied).

• Remove possible charcoal filters.

RECIRCULATION VERSION AIR OUTLET

• Cut a hole ø 125 mm in any shelf that may be posi-

tioned over the hood.

• Insert the flange 10a on the hood body outlet.

• Connect the flange to the outlet on the shelf over the

hood using a flexible or rigid pipe ø120 mm.

• Fix the pipe in position using sufficient pipe clamps

(not supplied).

• Fix the directional grille 8 on the recirculation air

outlet using the 2 screws 12e (2,9 x 12,7) provided.

• Ensure that the activated charcoal filters have been

inserted.

12e

8

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3

mm..

EN

1

0

10

USE

FUNCTION OF THE PULL-OUT SLIDING SUCTION PANEL

With the sliding panel kept closed is not possible to start up the motor of the hood, on the con-

trary is possible to engine and/or to switch off the lighting system. When the sliding panel is

pulled out the button pad is enabled, so that all functions are active and any functions that were

activated previously will be restored. Example: sliding panel pulled out : lights ON and motor

ON at speed T2; when the sliding panel is pushed back in again all these functions are turned

off. When the sliding panel is pulled out again, the hood will automatically restore the previ-

ous state, that is to say lights ON, motor ON at speed T2. If intensive speed was turned on at

the time the sliding panel was closed, the hood will not return to intensive speed when the slid-

ing panel is extracted, but to the speed set prior to that.

Control Panel

L T1 T2 T3 T4 T5 F

EN

1

11

The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button.

Basic functions

Touch

control

Dual Function

Indicator lights

L

When briefly pressed it switches the lighting system on

and off.

Touch control

unlit

Lights off

Touch control lit Motor on

T1

When pressed the motor is stopped, regardless of the

speed it is set to.

Touch control

unlit

Motor off

T2

When pressed the motor is set to the first speed

Touch control lit

By a brief pressing the motor is set to the second speed. Touch control lit Second speed on

T3

By pressing the touch control for approximately 2

seconds the Delay function is enabled, i.e delayed

shutdown of the appliance ensuring a complete

elimination of the residual odours. This function can

be activated at OFF-position and at 1°, 2° and

3°speeds. It can be stopped in advance by pressing

any of the touch controls (T) with the exception of

T3. The Delay function works according to the fol-

lowing scheme:

1°speed / OFF = 20 minuets

2°speed = 15 minutes

3°speed = 5 minutes

Flashing touch

control

Delay function on

T4

When pressed the motor is set to the third speed Touch control lit

T5

When pressed the motor is set to the intensive speed

timed to 5 minutes. At the end of 5 minutes of inten-

sive speed the hood starts again at the speed it was

set to previously. In case the hood is set to the inten-

sive speed directly from OFF-state it will then start

from the first speed after 5 minutes of intensive

speed.

Touch control lit

Metal grease filters

saturation alarm. Metal

grease filters need to

be washed. The alarm

starts up after 100

working hours.

F

When pressed for 4 seconds it resets the filter alarm

signal indicated by flashing of the touch control T1. This

procedure can be carried out only when the motor is

stopped.

Flashing touch

control

Charcoal odour filter

saturation alarm. Char-

coal filter has to be

replaced and metal

grease filters washed.

The alarm starts up

after 200 working

hours. (Activation;

check the paragraph

“Odour filter”)

EN

1

2

12

MAINTENANCE

Grease filters

CLEANING OF THE METAL CASSETTE FILTERS

Alarm reset

• Stop the motor.

• Press the F -touch control for at least 4 seconds until the T1 -

touch control flashes.

Cleaning the filters

• Filters can be washed in the dish machine. They need to be

washed every 2 months or even more frequently in case of par-

ticularly intensive use of the hood.

• Pull out the sliding suction panel.

• Remove the filters one by one, after having disconnected the

relative fastening elements.

• Wash the filters, taking care not to bend them. Let them get dry

before refitting them. (The colour of the filter surface may

change throughout the time but this has no influence to the fil-

ter efficiency).

• When refitting the filters, make sure that the handle is visible

on the outside.

• Close the sliding suction panel.

EN

1

3

13

Odour filter (Recirculation Version)

This filter cannot be washed or regenerated, and must be replaced when the F touch control starts

to flash, or at least once every 4 months. The alarm is only triggered when the motor is on.

Enabling/Disabling the alarm signal

• In Recirculation Version Hoods, the Filter saturation Alarm must be enabled at the time of

installation or later.

• Switch off the lights and the motor.

• Disconnect the mains power supply to the hood by removing the motor unit power supply

cable connector, switching off the power supply at the Mains or turning the Main switch off.

• Restore the connection, pressing and holding T2.

• Release the touch control, touch controls L, T2 and F will light up normally.

• Within 3 seconds press the touch control F until the key itself flashes to confirm as follows:

• 2 flashes – Charcoal odour Filter saturation Alarm ENABLED

• 1 flash - Charcoal odour Filter saturation Alarm DISABLED

REPLACING THE CHARCO

AL ODOUR FILTER

Reset the alarm signal

• Stop the motor.

• Press the touch control F for at least 4 seconds, until the touch

control T1 flashes.

Replace the Filter

• Pull out the sliding suction panel.

• Remove the metal grease filters.

• Remove the saturated charcoal filter, turning the fasteners pro-

vided.

• Fit the new filter and fasten it its correct position.

• Put the metal grease filters in their seats.

• Close the sliding suction panel.

Lighting

LIGHT REPLACEMENT

20 W Halogen lamp.

• Remove the metal terminals fixing the metal panel.

• Slide the metal panel out of one of the fastening clips. Lower

the unfastened part of the panel slightly, so that it can be com-

pletely removed.

• Extract the lamp from the Support.

• Replace with another of the same type, making sure that the

two pins are properly inserted in the lamp holder socket holes

• Replace the metal panel in reverse order.

Page is loading ...

436003570_ver1

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall

be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could oth-

erwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please

contact your local city office, your household waste disposal service or the shop where you purchased the product.

Le symbole sur le produit ou son emballage indique que ce produit ne peut être traité comme déchet ménager. Il doit plutôt être

remis au point de ramassage concerné, se chargeant du recyclage du matériel électrique et électronique. En vous assurant que ce

produit est éliminé correctement, vous favorisez la prévention des conséquences négatives pour l’environnement et la santé humaine

qui, sinon, seraient le résultat d’un traitement inapproprié des déchets de ce produit. Pour obtenir plus de détails sur le recyclage de ce

produit, veuillez prendre contact avec le bureau municipal de votre région, votre service d’élimination des déchets ménagers ou le

magasin où vous avez acheté le produit.

Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall

zu behandeln ist, sondern an einem Sammelpunkt für das Recycling von elektrischen und elektronischen Geräten abgegeben werden

muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen.

Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet. Weitere Informationen über das Recycling dieses Produkts

erhalten Sie von Ihrem Rathaus, Ihrer Müllabfuhr oder dem Geschäft, in dem Sie das Produkt gekauft haben.

Het symbool op het product of op de verpakking wijst erop dat dit product niet als huishoudafval mag worden behandeld. Het

moet echter naar een plaats worden gebracht waar elektrische en elektronische apparatuur wordt gerecycled. Als u ervoor zorgt dat dit

product op de correcte manier wordt verwijderd, voorkomt u mogelijk voor mens en milieu negatieve gevolgen die zich zouden kunnen

voordoen in geval van verkeerde afvalbehandeling. Voor meer details in verband met het recyclen van dit product, neemt u het best

contact op met de gemeentelijke instanties, het bedrijf of de dienst belast met de verwijdering van huishoudafval of de winkel waar u

het product hebt gekocht.

Electrolux EFP60271X User manual

Electrolux EFP60271X User manual

in other languages

Related papers

Other documents