Worx WX686L Owner's manual

WX686L

2.5A Oscillating Multi-Tool EN

2.5A Ensemble multi-outils oscillants F

2.5A Multi-Herramienta Oscilatoria ES

P03

P13

P21

Page is loading ...

2.5A Oscillating Multi-Tool EN

3

PRODUCT SAFETY

WARNING: Some dust created by power

sanding, sawing, grinding, drilling and

other construction activities contains chemicals

known to the State of California to cause

cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints;

• Crystalline silica from bricks and cement

and other masonry products ;

• Arsenic and chromium from

chemically-treated lumber.

Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals, work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed to

ﬁlter out microscopic particles.

WARNING: This product can expose you

to chemicals including lead, phthalate

or bisphenol A which are known to the State

of California to cause cancer, birth defects or

other reproductive harm. Wash your hands

after use. For more information go to www.

P65Warnings.ca.gov.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING: Read all safety

warnings, instructions, illustrations

and speciﬁcations provided with this

power tool. Failure to follow the warnings

and instructions may result in electric shock,

ﬁre and/or serious injury.

Save all warnings and instructions for

future reference.

The term power tool in the warnings refers to

your electric (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well

lit. Cluttered or dark areas invite

accidents.

b) Do not operate power tools in

explosive atmospheres, such as in the

presence of ﬂammable liquids, gases

or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs

with earthed (grounded) power tools.

Unmodiﬁed plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for

outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric

shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are

doing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the inﬂuence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may result in

serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

2.5A Oscillating Multi-Tool EN

4

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or

battery pack, picking up or carrying

the tool. Carrying power tools with your

ﬁnger on the switch or energizing power

tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewelry. Keep your hair

and clothing away from moving parts.

Loose clothes, jewelry or long hair can be

caught in moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure these are

connected and properly used. Use of

dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from

frequent use of tools allow you to

become complacent and ignore tool

safety principles. A careless action can

cause severe injury within a fraction of a

second.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool will do

the job better and safer at the rate for which

it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or remove the battery

pack, if detachable, from the power

tool before making any adjustments,

changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the

reach of children and do not allow

persons unfamiliar with the power

tool or these instructions to operate

the power tool. Power tools are

dangerous in the hands of untrained

users.

e) Maintain power tools and

accessories. Check for misalignment

or binding of moving parts, breakage

of parts and any other condition

that may affect the power tool’s

operation. If damaged, have the

power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking into

account the working conditions and

the work to be performed. Use of the

power tool for operations different from

those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces

dry, clean and free from oil and

grease. Slippery handles and grasping

surfaces do not allow for safe handling

and control of the tool in unexpected

situations.

5) SERVICE

a) Have your power tool serviced by

a qualiﬁed repair person using only

identical replacement parts. This will

ensure that the safety of the power tool is

maintained.

2.5A Oscillating Multi-Tool EN

5

SAFETY INSTRUCTION FOR

CUTTING

1. Hold power tool by insulated

gripping surfaces, when performing

an operation where the cutting

accessory may contact hidden wiring

or its own cord.Cutting accessory

contacting a “live” wire may make

exposed metal parts of the power tool

“live” and could give the operator an

electric shock.

2. Use clamps or another practical way

to secure and support the workpiece

to a stable platform. Holding the work

by hand or against your body leaves it

unstable and may lead to loss of control.

SYMBOLS

To reduce the risk of injury,

user must read instruction

manual

Warning

Wear ear protection

Wear eye protection

Wear dust mask

Double insulation

Make sure the tool is

unplugged prior to changing

accessories.

Before working with your tool

make sure that no power cords

will be damaged.

Avoid danger of injury from the

sharp edges of the accessories.

Accessories can become very

hot while working, presenting

danger of burns!

Wear protective gloves

High oscillation frequency.

Low oscillation frequency.

Lock

Unlock

2.5A Oscillating Multi-Tool EN

6

Universal Fit™ Interface *

*Works with other oscillating tool brands’ accessories.

The following compatible brands are trademarks owned by third parties which may be registered

by their respective owners: Black & Decker

®

, Bosch

®

, Chicago Electric

®

, Craftsman

®

, Dremel

®

, Fein

®

,

Genesis

®

, Makita

®

, Mastercraft

®

,

Milwaukee

®

, Performax

®

, Porter Cable

®

, Ridgid

®

, Ryobi

®

, Skil

®

, ShopSeries

®

, Rockwell and Tool Shop

®

.

Not all the accessories illustrated or described are included in standard delivery.

Venting slots

Variable speed controlOn/Off switch

Onboard Clip-in wrench

Flange

2.5A Oscillating Multi-Tool EN

7

TECHNICAL DATA

Type Designation WX686L (6-

designation of machinery, representative

of Oscillating Multi-Tool)

Rated voltage

120V~60Hz

Amps

2.5A

No load speed 11000-20000/min

Oscillation angle 3.2°

Protection class

/II

Tool weight

3.2lbs

ACCESSORIES

Onboard Clip-in wrench 1

Sanding pad-dust extraction

1

1-3/8” Standard wood end cut blade 1

Sanding sheet: 80#, 120#, 180# each 1

Only use the appropriate accessories intended

for this tool. Accessory information can be

found on the product packaging.

2.5A Oscillating Multi-Tool EN

8

A B1

B2

F

G

3

C

D

E

3

B3

3

2

2 2

2.5A Oscillating Multi-Tool EN

9

A B1

B2

F

G

3

C

D

E

3

B3

3

2

2 2

2.5A Oscillating Multi-Tool EN

10

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

ASSEMBLY AND OPERATION

Action Figure

Mounting accessories

Remove the onboard

Clip-in wrench

See Fig. A

Loosen the ﬂange and

insert accessories

See Fig.

B1,B2,B3

Tighten the ﬂange See Fig. C

Store the onboard Clip-in

wrench

See Fig. D, E

Operating the on/off switch See Fig. F

Using the variable speed dial See Fig. G

The Variable Speed Dial can be used to set

the optimum oscillating frequency according

to the accessories used and the respective

application.

Oscillation

frequency

Application

High oscillation

frequency

Sanding, sawing,

rasping and polishing

stone and metal.

Low oscillation

frequency

Scraping, polishing

varnishes.

WORKING HINTS FOR YOUR

TOOL

If your power tool becomes too hot, especially

when used at low speed, set the speed to

maximum and run it with no load for 2-3 minutes

to cool the motor. Avoid prolonged usage at very

low speeds. Always keep the blade sharp.

Always ensure the work piece is ﬁrmly held or

clamped to prevent movement. Any movement

of the material may affect the quality of the

cutting or sanding ﬁnish.

Start your tool before working and turn it off only

after you stop working.

Do not start sanding without having the

sandpaper ﬁtted.

Do not allow the sandpaper to wear away, it will

damage the sanding pad. The guarantee does not

cover sanding pad wear and tear.

Use coarse grit paper to sand rough surfaces,

medium grit for smooth surfaces and ﬁne grit for

ﬁnishing surfaces. If necessary, ﬁrst make a test

run on scrap material.

Excessive force will reduce the working

efﬁciency and cause motor overload. Replacing

the accessory regularly will maintain optimum

working efﬁciency.

MAINTAIN TOOLS WITH

CARE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no user

serviceable parts in your power tool. Never

use water or chemical cleaners to clean your

power tool. Wipe clean with a dry cloth. Always

store your power tool in a dry place. Keep the

motor ventilation slots clean. Keep all working

controls free of dust. Occasionally you may

see sparks through the ventilation slots. This is

normal and will not damage your power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualiﬁed persons in order to avoid

a hazard.

2.5A Oscillating Multi-Tool EN

11

APPLICATION

WARNING: the sawing teeth are very sharp. Do not touch during mounting and

application.

The workpiece must be clamped tightly before it is cut.

Pic Description Application

Sawing

Extended Life Carbide

Metal, hardened nails and

screws, tile, rebar, cement

backer board and other heavy

duty applications

Extended Life Bimetal Metal/

Wood End Cut Blade

Wood, plastic, ﬁberglass,

nails, non-ferrous metals, thin

sheet metal, hardened ﬁllers

Precision Wood Cut Blade Fast Cuts in wood, plastics

Wood End Cut Blade Wood, plastic, drywall

HSS Semicircle Saw Blade

Thin wood, plastic, ﬁberglass,

non-ferrous metals, thin

sheet metal, hardened ﬁllers,

window glazing

Sanding

Sanding Pad (Perforated) Wood, plastic, hardened ﬁllers

Sanding Finger Pad

Wood, plastic, hardened

ﬁllers

Rasping

Triangular Carbide Grit Rasp

Wood, hardened adhesives,

thin set, masonry

Carbide Rasp (Finger

Shaped)

Wood, hardened adhesives,

thin set, masonry

Removing

grout

Carbide Grit Semicircle Saw Blade

Grout, porous concrete, masonry

Diamond-Coated Semicircle

Saw Blade

Ceramic and stone tile,

backerboard

Scraping

Rigid Scraper Blade

Old paint, hardened

adhesives, caulk, carpet

Flexible Scraper Blade

Elastic sealants, paint,

adhesive residues, carpet

2.5A Oscillating Multi-Tool EN

12

We recommend that you purchase your

accessories listed in the above list from the

same store that sold you the tool. Refer to the

accessory packaging for further details. Store

personnel can assist you and offer advice.

NOTE: When plunging and sawing use a slight

pendulum motion, to allow sufﬁcient chip

removal.

The saw blade lasts longer if the wear

is distributed evenly. To ensure an even

distribution, loosen the saw blade or other

accessory as applicable, rotate it and retighten

ﬁrmly.

Cut/Sand with a constant movement and light

pressure.

Heavy pressure does not increase the cut/

removal rate – the accessory merely wears

faster.

Page is loading ...

AR01339301

www.worx.com

Worx WX686L Owner's manual

This manual is also suitable for

Worx WX686L Owner's manual

in other languages

Related papers

Other documents