American Standard 7010.024 User manual

Category
Wall & ceiling mounts accessories
Type
User manual

This manual is also suitable for

American Standard 7010.024 is a shelf designed for glass. It has a length of 24" (610mm). It can be mounted on any wall with the included anchors and screws, but it works best if secured to a wall stud or cross brace within the wall using 1-1/2" long screws (not supplied). It has a simple design that makes it easy to clean and maintain. It is recommended to rinse the product clean with clear water and dry it with a soft cotton flannel cloth. Avoid cleaning the product with soaps, acid, or harsh cleaners.

American Standard 7010.024 is a shelf designed for glass. It has a length of 24" (610mm). It can be mounted on any wall with the included anchors and screws, but it works best if secured to a wall stud or cross brace within the wall using 1-1/2" long screws (not supplied). It has a simple design that makes it easy to clean and maintain. It is recommended to rinse the product clean with clear water and dry it with a soft cotton flannel cloth. Avoid cleaning the product with soaps, acid, or harsh cleaners.

Certified to comply with ANSI A112.18.1
1
MOUNTING BRACKET INSTALLATION
18" TOWEL BAR, 24" TOWEL BAR AND 24" GLASS SHELF
The 18" TOWEL BAR, 24" TOWEL BAR and GLASS SHELF work best if secured to a wall stud or cross brace within the wall, using 1-1/2"
long SCREWS (3) not supplioed.
If the 18" TOWEL BAR, 24" TOWEL BAR and GLASS SHELF are to be installed on a tile or plaster wall the ANCHORS and SCREWS
should be used.
GREEN TEA
Installation
Instructions
7010.180
7010.240
7010.024
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read instructions carefully before you begin.
INSTALL 18" TOWEL BAR, AND 24" TOWEL BAR
2
18"TOWEL BAR
24"TOWEL BAR
GLASS SHELF
Regular Screwdriver
Level
Recommended Tools
Phillips Screwdriver
Drill
10'
Tape Measure
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
Secure MOUNTING PLATES (1) to wall with SCREWS (2).
Determine desired height and location (optional) for the accessory and mark a center line. Use the full size template supplied to mark
hole locations for the mounting brackets. For the 24" TOWEL BAR and GLASS SHELF use 24” template. For 18” TOWEL BAR use 18”
template. If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).
For installations on drywall or tiled walls, use ANCHORS (4) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Use MOUNTING
BRACKET (1) as a template and mark the mounting holes. Drill three 1/8" diameter holes a minimum of 1-1/4" deep. Insert the three
ANCHORS (4) flush with face of the finished wall.
3
INSTALL GLASS SHELF
GREEN TEA
18" & 24" TOWEL BAR
GLASS SHELF
CHROME
SATIN NICKEL
BLACKENED BRONZE
002
295
068
Replace the "YYY" with
appropriate finish code
18" & 24" TOWEL BAR
24" GLASS SHELF
Place right ESCUTCHEON (5) onto MOUNTING BRACKET (1), and secure
with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.
Place LEFT ESCUTCHEON (5a) onto MOUNTING BRACKET (1a) and
secure with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.
MODEL NUMBERS
M 9 6 8 6 3 1M 9 6 8 6 3 1
M 9 6 8 6 3 1
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uct nam es l is ted her ei n ar e tra de ma rk s of Am er ic an Stan da rd I nc .
© Am erican St an da rd Inc. 2 00 7
Place ESCUTCHEON (1,1a) onto installed MOUNTING
BRACKETS (2) and secure with SET SCREWS (3) using
2.5mm HEX WRENCH (4) supplied.
Remove SCREWS (5) and top WASHERS (6) from
SHELF RISER (7).
Install GLASS SHELF (8) onto SHELF RISERS (7).
Secure GLASS SHELF (8) with SCREWS (5) and
WASHERS (6).
5,
1a
1
8
6
1a
1
6
6
5
5a
5a
4
FINISHED WALL
2
1
1-1/2"
M962608-0070A
MOUNTING KIT
M962608-0070A
MOUNTING KIT
4
1
2
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
CENTER
LINE
LEVEL
3
24" (610mm)
18" (457mm)
or
6
7
3
3
4
IN MEXICO 01-800-839-12-00
7010.180
7010.240
7010.024
M962610-0070A
GLASS SHELF
M962611-0070A
SHELF MOUNTING KIT
CENTER LINE
(OPTIONAL TO
FINISHED FLOOR)
TEMPLATE
FINISHED WALL
ANCHORS
MOUNTING
BRACKET
MOUNTING
SCREWS
(SUPPLIED)
24" (610mm)
24" TOWEL BAR
GLASS SHELF
7010.2407010.024
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
MOUNTING BRACKET
for GLASS SHELVE
MOUNTING BRACKET
for GLASS SHELVE
4
5
2
2
2
18" (457mm)
18" TOWEL BAR
7010.180
CENTER LINE
(OPTIONAL TO
FINISHED FLOOR)
TEMPLATE
FINISHED WALL
ANCHORS
MOUNTING
BRACKET
MOUNTING
SCREWS
(SUPPLIED)
24" (610mm)
24" TOWEL BAR
GLASS SHELF
7010.2407010.024
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
MOUNTING BRACKET
for GLASS SHELVE
MOUNTING BRACKET
for GLASS SHELVE
18" (457mm)
18" TOWEL BAR
7010.180
5
7
M962609-YYY0A
ESCUTCHEON KIT
MOUNTING BRACKET
MOUNTING
SCREW
FINISHED WALL
SET SCREW
XXXXXX-YYY0A
POST
POSITION OF
MOUNTING BRACKET
FOR GLASS SHELF
(NOTE POSITION OF MOUNTING BRACKET.}
POSITION OF
MOUNTING BRACKET
FOR TOWEL BARS
Certified to comply with ANSI A112.18.1
1
MOUNTING BRACKET INSTALLATION
18" TOWEL BAR, 24" TOWEL BAR AND 24" GLASS SHELF
The 18" TOWEL BAR, 24" TOWEL BAR and GLASS SHELF work best if secured to a wall stud or cross brace within the wall, using 1-1/2"
long SCREWS (3) not supplioed.
If the 18" TOWEL BAR, 24" TOWEL BAR and GLASS SHELF are to be installed on a tile or plaster wall the ANCHORS and SCREWS
should be used.
GREEN TEA
Installation
Instructions
7010.180
7010.240
7010.024
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read instructions carefully before you begin.
INSTALL 18" TOWEL BAR, AND 24" TOWEL BAR
2
18"TOWEL BAR
24"TOWEL BAR
GLASS SHELF
Regular Screwdriver
Level
Recommended Tools
Phillips Screwdriver
Drill
10'
Tape Measure
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
Secure MOUNTING PLATES (1) to wall with SCREWS (2).
Determine desired height and location (optional) for the accessory and mark a center line. Use the full size template supplied to mark
hole locations for the mounting brackets. For the 24" TOWEL BAR and GLASS SHELF use 24” template. For 18” TOWEL BAR use 18”
template. If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).
For installations on drywall or tiled walls, use ANCHORS (4) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Use MOUNTING
BRACKET (1) as a template and mark the mounting holes. Drill three 1/8" diameter holes a minimum of 1-1/4" deep. Insert the three
ANCHORS (4) flush with face of the finished wall.
3
INSTALL GLASS SHELF
GREEN TEA
18" & 24" TOWEL BAR
GLASS SHELF
CHROME
SATIN NICKEL
BLACKENED BRONZE
002
295
068
Replace the "YYY" with
appropriate finish code
18" & 24" TOWEL BAR
24" GLASS SHELF
Place right ESCUTCHEON (5) onto MOUNTING BRACKET (1), and secure
with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.
Place LEFT ESCUTCHEON (5a) onto MOUNTING BRACKET (1a) and
secure with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.
MODEL NUMBERS
M 9 6 8 6 3 1M 9 6 8 6 3 1
M 9 6 8 6 3 1
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uct nam es l is ted her ei n ar e tra de ma rk s of Am er ic an Stan da rd I nc .
© Am erican St an da rd Inc. 2 00 7
Place ESCUTCHEON (1,1a) onto installed MOUNTING
BRACKETS (2) and secure with SET SCREWS (3) using
2.5mm HEX WRENCH (4) supplied.
Remove SCREWS (5) and top WASHERS (6) from
SHELF RISER (7).
Install GLASS SHELF (8) onto SHELF RISERS (7).
Secure GLASS SHELF (8) with SCREWS (5) and
WASHERS (6).
5,
1a
1
8
6
1a
1
6
6
5
5a
5a
4
FINISHED WALL
2
1
1-1/2"
M962608-0070A
MOUNTING KIT
M962608-0070A
MOUNTING KIT
4
1
2
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
CENTER
LINE
LEVEL
3
24" (610mm)
18" (457mm)
or
6
7
3
3
4
IN MEXICO 01-800-839-12-00
7010.180
7010.240
7010.024
M962610-0070A
GLASS SHELF
M962611-0070A
SHELF MOUNTING KIT
CENTER LINE
(OPTIONAL TO
FINISHED FLOOR)
TEMPLATE
FINISHED WALL
ANCHORS
MOUNTING
BRACKET
MOUNTING
SCREWS
(SUPPLIED)
24" (610mm)
24" TOWEL BAR
GLASS SHELF
7010.2407010.024
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
MOUNTING BRACKET
for GLASS SHELVE
MOUNTING BRACKET
for GLASS SHELVE
4
5
2
2
2
18" (457mm)
18" TOWEL BAR
7010.180
CENTER LINE
(OPTIONAL TO
FINISHED FLOOR)
TEMPLATE
FINISHED WALL
ANCHORS
MOUNTING
BRACKET
MOUNTING
SCREWS
(SUPPLIED)
24" (610mm)
24" TOWEL BAR
GLASS SHELF
7010.2407010.024
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
MOUNTING BRACKET
for GLASS SHELVE
MOUNTING BRACKET
for GLASS SHELVE
18" (457mm)
18" TOWEL BAR
7010.180
5
7
M962609-YYY0A
ESCUTCHEON KIT
MOUNTING BRACKET
MOUNTING
SCREW
FINISHED WALL
SET SCREW
XXXXXX-YYY0A
POST
POSITION OF
MOUNTING BRACKET
FOR GLASS SHELF
(NOTE POSITION OF MOUNTING BRACKET.}
POSITION OF
MOUNTING BRACKET
FOR TOWEL BARS
Certified to comply with ANSI A112.18.1
1
MOUNTING BRACKET INSTALLATION
18" TOWEL BAR, 24" TOWEL BAR AND 24" GLASS SHELF
The 18" TOWEL BAR, 24" TOWEL BAR and GLASS SHELF work best if secured to a wall stud or cross brace within the wall, using 1-1/2"
long SCREWS (3) not supplioed.
If the 18" TOWEL BAR, 24" TOWEL BAR and GLASS SHELF are to be installed on a tile or plaster wall the ANCHORS and SCREWS
should be used.
GREEN TEA
Installation
Instructions
7010.180
7010.240
7010.024
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read instructions carefully before you begin.
INSTALL 18" TOWEL BAR, AND 24" TOWEL BAR
2
18"TOWEL BAR
24"TOWEL BAR
GLASS SHELF
Regular Screwdriver
Level
Recommended Tools
Phillips Screwdriver
Drill
10'
Tape Measure
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
Secure MOUNTING PLATES (1) to wall with SCREWS (2).
Determine desired height and location (optional) for the accessory and mark a center line. Use the full size template supplied to mark
hole locations for the mounting brackets. For the 24" TOWEL BAR and GLASS SHELF use 24” template. For 18” TOWEL BAR use 18”
template. If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).
For installations on drywall or tiled walls, use ANCHORS (4) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Use MOUNTING
BRACKET (1) as a template and mark the mounting holes. Drill three 1/8" diameter holes a minimum of 1-1/4" deep. Insert the three
ANCHORS (4) flush with face of the finished wall.
3
INSTALL GLASS SHELF
GREEN TEA
18" & 24" TOWEL BAR
GLASS SHELF
CHROME
SATIN NICKEL
BLACKENED BRONZE
002
295
068
Replace the "YYY" with
appropriate finish code
18" & 24" TOWEL BAR
24" GLASS SHELF
Place right ESCUTCHEON (5) onto MOUNTING BRACKET (1), and secure
with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.
Place LEFT ESCUTCHEON (5a) onto MOUNTING BRACKET (1a) and
secure with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.
MODEL NUMBERS
M 9 6 8 6 3 1M 9 6 8 6 3 1
M 9 6 8 6 3 1
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uct nam es l is ted her ei n ar e tra de ma rk s of Am er ic an Stan da rd I nc .
© Am erican St an da rd Inc. 2 00 7
Place ESCUTCHEON (1,1a) onto installed MOUNTING
BRACKETS (2) and secure with SET SCREWS (3) using
2.5mm HEX WRENCH (4) supplied.
Remove SCREWS (5) and top WASHERS (6) from
SHELF RISER (7).
Install GLASS SHELF (8) onto SHELF RISERS (7).
Secure GLASS SHELF (8) with SCREWS (5) and
WASHERS (6).
5,
1a
1
8
6
1a
1
6
6
5
5a
5a
4
FINISHED WALL
2
1
1-1/2"
M962608-0070A
MOUNTING KIT
M962608-0070A
MOUNTING KIT
4
1
2
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
CENTER
LINE
LEVEL
3
24" (610mm)
18" (457mm)
or
6
7
3
3
4
IN MEXICO 01-800-839-12-00
7010.180
7010.240
7010.024
M962610-0070A
GLASS SHELF
M962611-0070A
SHELF MOUNTING KIT
CENTER LINE
(OPTIONAL TO
FINISHED FLOOR)
TEMPLATE
FINISHED WALL
ANCHORS
MOUNTING
BRACKET
MOUNTING
SCREWS
(SUPPLIED)
24" (610mm)
24" TOWEL BAR
GLASS SHELF
7010.2407010.024
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
MOUNTING BRACKET
for GLASS SHELVE
MOUNTING BRACKET
for GLASS SHELVE
4
5
2
2
2
18" (457mm)
18" TOWEL BAR
7010.180
CENTER LINE
(OPTIONAL TO
FINISHED FLOOR)
TEMPLATE
FINISHED WALL
ANCHORS
MOUNTING
BRACKET
MOUNTING
SCREWS
(SUPPLIED)
24" (610mm)
24" TOWEL BAR
GLASS SHELF
7010.2407010.024
DRILL 3 PILOT HOLES FOR
WOOD SCREWS (2) OR
1/8" DIA. HOLES FOR
ANCHORS (4)
CENTER
LINE
MOUNTING BRACKET
for GLASS SHELVE
MOUNTING BRACKET
for GLASS SHELVE
18" (457mm)
18" TOWEL BAR
7010.180
5
7
M962609-YYY0A
ESCUTCHEON KIT
MOUNTING BRACKET
MOUNTING
SCREW
FINISHED WALL
SET SCREW
XXXXXX-YYY0A
POST
POSITION OF
MOUNTING BRACKET
FOR GLASS SHELF
(NOTE POSITION OF MOUNTING BRACKET.}
POSITION OF
MOUNTING BRACKET
FOR TOWEL BARS
  • Page 1 1
  • Page 2 2
  • Page 3 3

American Standard 7010.024 User manual

Category
Wall & ceiling mounts accessories
Type
User manual
This manual is also suitable for

American Standard 7010.024 is a shelf designed for glass. It has a length of 24" (610mm). It can be mounted on any wall with the included anchors and screws, but it works best if secured to a wall stud or cross brace within the wall using 1-1/2" long screws (not supplied). It has a simple design that makes it easy to clean and maintain. It is recommended to rinse the product clean with clear water and dry it with a soft cotton flannel cloth. Avoid cleaning the product with soaps, acid, or harsh cleaners.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI