Haier HW–D1270TVE ME User manual

Haier
Brand
Haier
Model
HW–D1270TVE ME
Category
Washing machines
Type
User manual
Quickwash
Wool
Synthetics
Cotton&Linen
Prewash
Delay
Wash Rinse Spin Dry
Extra
rinse
Dry EcoTime Start/
Pause
Power
Temp
Speed
Delay Extra
rinse
Rinse
hold
Eco Start/
Pause
pre-
wash
Rinse SpinWash
Silk
Sport
Quick Wash
Rinse
Spin
Drain
ON
OFF
AUTOMATIC DRUM WASHING MACHINE
USER MANUAL
HW-D1270TVE
HW–D1270TVE ME
HW-D1470TVE
HW–D1470TVE ME
TABLE OF CONTENTS
01 - 07 08 - 1
3
14 - 1
8
COMPONENTS> .............................. 3
PREPARATION> ............................... 4
SAFETY INSTRUCTIONS> .................. 5
INSTALLATION> ............................... 6
CONTROL PANEL> ........................... 8
BEFORE USE USING THE APPLIANCE MAINTENANCE
As a responsible retailer we care about the environment. As such we urge you to follow the correct disposal
procedure for your product and packaging materials.
This will help conserve natural recourses and ensure that it is recycled in a manner that protects health and
the environment.
You must dispose of this product and its packaging according to local laws and regulations. Because this
product contains electronic components, the product and its accessories must be disposed of separately from
household waste when the product reaches its end of life.
Contact your local authority to learn about disposal and recycling. The product and packaging should be taken
to your local collection point for recycling. Some collection points accept products free of charge.
We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur
as a resultof product improvement and development.
LEGEND
DISPOSAL
For your safety, any instructions in this manual with this "Warning" sign must
be followed strictly.
Yes
No
Optional
PROGRAM SELECTION> .................. 10
CONSUMPTION AND TECHNICAL DATA> ...11
WASHING METHODS> ................... 12
CLEANING & CARE> ....................... 16
DISPLAY CODES> .......................... 18
TROUBLESHOOTING> ..................... 19
3
BEFORE US
E
AUTOMATIC DRUM WASHING MACHINE
USER MANUAL
HW–C1470TVE
HW–C1270TVE
HW–C1070TVE
HW–C870TVE
HW–C1470TVE ME
HW–C1270TVE ME
HW–C1070TVE M E
HW–C870TVE ME
1x Inlet hose assembly
3x Blanking plugs
1x User manual 1x Drain hose bracket
COMPONENTS
Please read these instructions carefully before using this appliance. The instructions contain important information which will help you
get the best out of the appliance and ensure safe and proper installation, use and maintenance.
Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass on this manual so that the
new owner can become familiar with the appliance and safety warnings.
ACCESSORIES
Check the accessories and literature in accordance with this list:
1x Bottom cover
4
BEFORE USE
Quickwash
Wool
Synthetics
Cotton&Linen
Prewash
Delay
Wash Rinse Spin Dry
Extra
rinse
Dry EcoTime Start/
Pause
Power
Temp
Speed
Delay Extra
rinse
Rinse
hold
Eco Start/
Pause
pre-
wash
Rinse SpinWash
Silk
Sport
Quick Wash
Rinse
Spin
Drain
ON
OFF
Power switch
Door handle
Work Top
Washer door
Control Panel
Detergent distribution drawer
Filter cover
S1
S2
S3
T3
T2
T1
Drain hose
Water inlet valve
Power cord
Back cover
Back cover screws
Transportation bolts
PREPARING THE MACHINE
Remove all the packing materials to prevent unsteadiness, including the polystyrene base. Upon
opening the package, water drops may be seen on the plastic bag and the porthole. This is normal
phenomenon resulting from water tests in the factory.
DESCRIPTION
This diagram may be slightly different from the layout of the washing machine you have just
purchased due to technical improvements.
PREPARATION
5
BEFORE US
E
SAFETY INSTRUCTIONS
DO ...
... make sure that the transport bolt are removed.
... Use a separate earthed socket for the power supply.
... Make sure that the plug is accessible.
... Hold the plug and not the electric cable when unplug-
ging the power supply.
... Make sure that the fuses in the power circuit are rated
for 15A.
... Keep away from heat sources and direct sun light to
prevent plastic and rubber components from aging.
... Make sure that the power cord is not caught under or
in the appliance and avoid damage to the power cable.
... Check that hose joints and connections are fi rm and no
water can leak. If joints are loose or there is leakage, turn off the
water supply and repair. Do not use the washing machine until
the hoses are properly fi xed.
DO ...
... Pull up zips and fi x loose threads to prevent the items
from being entangled. If necessary, put small items into a net bag
or pillow.
... Turn off the machine after each wash program and switch
it off at the mains to save electricity and for safety. Wipe clean
the lower part of the porthole.
... Keep the door slightly open when the washing machine is
not in use to prevent formation of odours.
... Let the power cord be replaced by the manufacturer, his
service agent or other accordingly qualifi ed persons, in case it is
damaged.
... Ensure that the appliance is not used by persons with re-
duced physical, sensory or mental capabilities, lack of experience
and knowledge without supervision or instruction by a person
responsible for their safety.
... Supervise children to ensure that they do not play with
the appliance.
DO NOT ...
... Touch or use the appliance when barefoot or with wet
or damp hands or feet.
... Use fl ammable detergent or dry cleaning agent.
... Use any fl ammable sprays in close vicinity to the appli-
ance.
... Remove or insert the plug in the presence of fl ammable
gas.
... Allow children or infi rm persons to play with the appliance
or packing materials.
... Install the appliance outdoors in a damp place, or in an
area which may be prone to water leaks such as under or near a
sink unit. In the event of a water leak allow the machine to dry
naturally.
... Place the washing machine directly on a carpet, or close
to a wall or furniture.
DO NOT ...
... Touch the washer door during the washing process - it
gets hot!
...Place heavy objects or sources of heat or damp on top
of the appliance.
... Hot wash foam rubber or sponge-like materials.
... Open the detergent distribution drawer during the wash
cycle.
... Force the washer door open. The door is fi tted with a
self-lock device and will open shortly after the washing procedure
is ended.
... Open the washer door if the water level is visibly over
the porthole.
... Cover the washing machine with plastic cover so that
inside dampness cannot be kept in.
BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME
DURING DAILY USE OF THE APPLIANCE
6
BEFORE USE
3.
1.
2.
4.
ADJUSTING THE BOTTOM COVER
When open the shrink package,you will fi nd a calcium plastic board
which is laid on the top of washing machine as shown in fi g.1.The board
is used for reducing noise by pasting it under the cabinet when setting
as shown in fi g.2
It keeps out the dampness and reduces the noise.
DISMANTLE THE TRANSPORTATION BOLTS
The transportation bolts are designed for clamping anti-vibration
components inside of the washing machine during the transportation
process.
Remove the back cover.1.
Remove the three bolts on the rear side and take out the synthetic 2.
stabilisers from within the machine.
Replace the back cover.3.
Fill the holes left by the bolts with blanking plugs.4.
Note:
1.When you replace the back cover,the convexity must
face to outside, and you
have to insert the back cover from the two gaps as shown
in fi g.3.
2.Keep the transportation bolts and synthetic stabilisers in
a safe place for later use.
INSTALLATION
Adjusting the washing machine
There are adjustable feet under the bottom of the washing machine. Before use, they should be
adjusted so that the machine is level. This will minimise vibrations and thus noise during use. It will
also reduce wear and tear. We recommend using a spirit level to level the appliance.
fig.3
7
BEFORE US
E
1.
2.
1.
80 - 100cm
2.
INLET HOSE
1. Connect the nut on the inlet hose to the connector on the water
valve.
2. Apply inlet hose to a water tab with cold, fresh water.
Note: Use the hose-set supplied with the appliance. Old
hose-sets should not be reused.
DRAIN HOSE
1. Use the drain hose bracket to keep the end of the drain hose retained
and prevent the outfl ow of water. Don't extend the length of the drain
hose; if an extended hose is required, please consult a serviceman.
2. The height of the drainage outlet must be 80-100 cm. Fix the drain
hose to the clip at the back of the washing machine to prevent it from
dropping off.
Note: The drain hose should not be submerged in water
and should be securely fi xed and leak-free. If the drain
hose is placed on the ground or if the pipe is at a height
of less than 80cm, the washing machine will continuously
drain while being fi lled (self-siphoning).
CONNECTING TO THE POWER SUPPLY
Before connecting to the power supply, check:
¬ The socket is adequate for the maximum power of the washing machine
(For safety, fuses in the power circuit should be rated for no less than 15A).
¬ The voltage should meet the requirement.
¬ The power outlet should be capable of accepting the washing machine plug.
¬ Connect the machine to an earthed socket outlet.
8
BEFORE USE
Quickwash
Wool
Synthetics
Cotton&Linen
Prewash
Delay
Wash Rinse Spin Dry
Extra
rinse
Dry EcoTime Start/
Pause
Power
Temp
Speed
Delay Extra
rinse
Rinse
hold
Eco Start/
Pause
pre-
wash
Rinse SpinWash
Silk
Sport
Quick Wash
Rinse
Spin
Drain
ON
OFF
KA
DE
J
FHG C
BI
A ¬ Program knob _Select program by turning the knob .
B ¬ Temperature
button
_ Select the desired washing temperature (--,30,40,50, 60,90°C ) by pressing and holding down
this button. When selected, the temperature is shown on the display. Cold wash is selected when the
symbol "--" is displayed.
C ¬ Speed button _ Select the desired spin speed (0, 400, 600, 800, 1000, 1200,) by pressing and holding down this
button. When selected, the speed value is shown on the display. The washing machine does not spin
when "0" is displayed. The washing machine spins at 1200 rpm when "1200" is displayed.
D ¬ Start/pause
button
_ If you press this button, ":" will be displayed and operation will start. If you press this button during
a wash cycle, the ":" sign will start blinking and operation will pause. Press it again to resume opera-
tion. Note: After operation is suspended, the washing temperature, spinning speed
and other functions can not be reset.
A Program knob
B Temperature button
C Speed button
D Start/pause button
E Eco button
F Rinse hold button
G Extra rinse button
H Delay button
I Display
J Detergent distribution drawer
OPERATIONAL FUNCTIONS
CONTROL PANEL
K Power button
9
BEFORE US
E
2
1
3
E ¬ Eco button _ Before a washing program, press this button to set the required washing load (1 :3-FulI), the wash-
ing machine will automatically adjust the water consumption, heating time and washing time. Users
can select the washing load as required for economical operation.
Note:1."1 :3-Full"refers to the four levels of washing load. If the laundry is more
than half of the drum content, it is recommended to select 2:3-Full: otherwise,
select 1:3-1:2 2.For"synthetics","sport" ,you can only select 1:3-1 :2-2:3.
3.Please adjust the detergent quantity according to the washing load selected.
F ¬ Rinse hold
button
_ If you press this button, the washing machine will not drain the water after the last rinsing opera-
tion, but start a soaking cycle. The indicator light goes on. To spin the laundry, press this button again.
The indicator light turns off and the program continues to the end. Note: Press only when "Prewash",
"Cotton&linen", "Synthetics" or "Rinse" is selected.
G ¬ Extra rinse
button
_ Press this button, the washing machine will perform additional rinses. The light turns off and the
display disappears when the extra rinse ends.
Note:Select this function when programe 1-6 or 9 is selected
H ¬ Delay button _ Press the button repeatedly before starting the program to enter the time you want the machine to
be fi nished in, the start will delay from 0.5 to 24 hours in 30-minute intervals. This also includes the
length of the program itself, so the delay time must be longer than the program length selected.
I ¬Display _ The display shows the washing time remaining, the selected temperature and speed, the options,
the alarm warning, etc.
J ¬ Detergent
distribution drawer
_ Instructions are printed on the handle of the drawer.
Open the drawer, three compartments can be seen:
Compartment 1: Pre-wash detergent
Compartment 2: Detergent for programs 1 to 8
Compartment 3: Softener, conditioning agent,
perfume, and other additives.
K ¬ Power button _ Press this button to turn the machine on and off.
2
1
3
1 Detergent compartment for prewash mode
2 Detergent compartment
3 Compartment for softener and other additives
1
0
APPLIANC
E
SING THE
PROGRAM SELECTION
PROGRAM MODES
Temperature Recommended
Program Maximum Preset 2 3 1 Laundry Preset spin speed
1 ¬ Prewash -- to 90 °C 40 °C Cotton fabrics 1000 rpm
2 ¬ Cotton-
&linen
-- to 90 °C 40 °C
Cotton fabrics 1000 rpm
3 ¬ Synthetics 0 ° to 60 °C 40 °C
Fast colours / Medium
soiled
1000 rpm
4 ¬ Wool 0 ° to 40 °C /
Wool fabrics /
5 ¬ Handwash 0 ° to 40 °C /
Cotton or synthetic /
6 ¬ Silk 0 ° to 40 °C /
//
7 ¬ Sport 0 ° to 40 °C 40 °C
/ 1000 rpm
8 ¬ Quick wash 0 ° to 40 °C 40 °C
/ 1000 rpm
9 ¬ Rinse / /
/ 1000 rpm
10 ¬ Spin / /
/ 1000 rpm
11 ¬ Drain / /
//
Yes No Optional
1
1
U
SING THE APPLIANC
E
CONSUMPTION AND TECHNICAL DATA
TECHNICAL DATA
CONSUMPTION TABLE
The wash cycle times are intended as a guide only. The actual time used may vary due to different water pressure, initial water tempera-
ture, etc.
PROGRAM
MAX.
LOAD
ENERGY
CONSUMPTION
WATER
CONSUMPTION
WASHING
TIME
¬ Prewash 7 kg 0.89 kWh 87L 2:32 h
¬ Cotton 60 °C *
)
7 kg 1.19 kWh 60 L 2:58 h
¬ Cotton 40 °C 7 kg 0.66kWh 79 L 2:12 h
¬ Synthetics 3 kg 0.475 kWh 55L 1:35 h
¬ Wool 2kg 0.055kWh 44L 0:41 h
¬ Handwash 3.5 kg 0.017 kWh 44L 0:39 h
¬ Silk 2 kg 0.03 kWh 44L 0:41 h
¬ Sport 3.5 kg 0.3 kWh 34 L 0:25 h
¬ Quick 3.5 kg 0.37 kWh 34L 0:29 h
¬ Hand wash 4 kg 0.147 kWh 41.8 L 0:57 h
HW-D1270TVE/ME HW-D1470VE/ME
Power source 220 - 240 V / 50 Hz 220 - 240 V / 50 Hz
Max. working current (A) 10 10
Water pressure (MPa) 0.03 ≤ P ≤ 1 0.03 ≤ P ≤ 1
Nominal load (kg) 7 7
Spinning speed (r/min) 1200 1400
Washing programs 12 12
Max. power (W) 2000 2000
Dimensions (HxDxW mm) 840 x 610 x 595 840 x 610 x 595
Net weight (kg) 72 72
*
)
EN 60456 test program / Energy label program with Cotton 60 °C and max. spin speed.
1
2
APPLIANC
E
SING THE
WASHING METHODS
POWER SUPPLY
Connect the washing machine to the power supply (220V to 240V~/50Hz).
WATER CONNECTION
Turn on the tap. The water must be clean and clear.
Note: Before use, check for leakage in the joints between the tap and the inlet hose by turning on the tap.
PREPARING THE LAUNDRY
¬ Sort out clothes according to fabric (cotton, synthetics, wool or silk) and to how dirty they are.
¬ Separate white clothes from coloured ones. Wash them fi rst by hand to check if they fade or run.
¬ Empty pockets (keys, coins, etc.) and remove the harder decorative objects (e.g. brooches).
¬ Garments without hems, underwear, fi nely woven textile such as fi ne curtains are to be put into wash
bag (it is better not to wash them in a washing machine).
¬ Close zippers and hooks, make sure the buttons are sewn on tightly and place small items such as socks, belts, bras, etc. in the
wash bag.
¬ Unfold large pieces of fabric such as bed sheets, bedspreads, etc.
¬ Turn shirts inside out.
This washing machine is for domestic use only. Do not use it for purposes other than that for
which it was designed. Follow the instructions given on the label of each garment and wash only
machine-washable garments.
PLEASE NOTE
Quickwash
Wool
Synthetics
Cotton&Linen
Prewash
Power
Silk
Sport
Quick Wash
Rinse
Spin
Drain
O
N
O
F
1
3
U
SING THE APPLIANC
E
LOADING THE MACHINE
Open the washer door, put in the laundry piece by piece. Close the door tightly.
¬ When fi rst using the washing machine, let it run unloaded for one program to prevent the laundry from
being tainted by oil or dirty water from the washing machine.
¬ Do not overload the washing machine.
SELECTING DETERGENT
The washing effi ciency and the performance is determined by the quality of detergent used. Special non-
foaming detergent produces good washing results. Use specifi c detergents for synthetic and woollen goods.
Do not use dry cleaning agents such as trichloroethylene and similar products.
Note: Do not add more detergent than needed. Please follow the dosage recommendation on the detergent
package.
ADDING DETERGENT
Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments. Push back the
drawer gently. (Refer to the instructions on the drawer)
Caution:
¬ For pre-washing program, detergent should be added to both compartments 1 and
2. For other programs, do not add detergent to compartment 1.
¬ Use liquid detergent according to the instructions on its package. Do not use liquid
detergent if the pre-wash mode or "Start delay" is selected.
¬ Do not overuse softener; otherwise, it will damage the artifi cial fi bers.
SELECTING PROGRAM
To get the best washing results, an appropriate washing program should be selected according to the laundry type. There are instructions
on the handle of the detergent distribution drawer. Please turn the program knob to select the right program.
SELECTING FUNCTIONAL
Select the required options. (Refer to the "Control panel" pages 08 and 09)
2
1
3
Quickwash
Wool
Synthetics
Cotton&Linen
Prewash
Delay
Wash Rinse Spin Dry
Extra
rinse
Dry EcoTime Start/
Pause
Power
Temp
Speed
Delay Extra
rinse
Rinse
hold
Eco Start/
Pause
pre-
wash
Rinse SpinWash
Silk
Sport
Quick Wash
Rinse
Spin
Drain
ON
OFF
Delay
Wash Rinse Spin Dry
Extra
rinse
Dry EcoTime Start/
Pause
Temp
Speed
Delay Extra
rinse
Rinse
hold
Eco Start/
Pause
pre-
wash
Rinse SpinWash
14
APPLIANC
E
SING THE
SETTING WASHING TEMPERATURE
Press and hold down the temperature button until the desired temperature is selected or the symbol "--"
for no water heating.
SETTING SPIN SPEED
Press and hold down the speed button until the desired speed is selected or the symbol "0" is selected
for no spin. See "Operational functions" on the "Control panel" pages (08 and 09) for selecting
temperature and spin speed. It is advisable to select the recommended value.
WASHING
Press the Start/Pause button. The washing machine will operate according to the pre-set programs.
The washing machine will stop operation automatically when a washing cycle ends. The "End" sign will
appear on the display. Open the washer door and take out the laundry.
AFTER WASHING
Turn off the water supply and unplug the power cord. Open the washer door to prevent formation of
moisture and odours. Let the door open while not used.
TIPS FOR SAVING ENERGY
Collect clothes for one full wash load.1.
Avoid overloading the washing machine.2.
Pre-wash only heavily soiled clothes.3.
Reduce the amount of detergent or choose the speed up wash programs for slightly soiled clothes.4.
Choose a proper washing temperature. Modern detergents can wash with very good result already in lower temperature than 5.
60°C. Only user higher temperature than 60°C for heavily soiled laundry.
Follow the dosage recommendation on the detergent package to avoid using too much detergent.6.
y
EcoTime Start/
Pause
Temp
Speed
se
d
Eco Start/
Pause
y
EcoTime Start/
Pause
Temp
Speed
se
d
Eco Start/
Pause
1
5
U
SING THE APPLIANC
E
Bed sheet (single) Cotton Approximately 800g
Blanket Wool Approximately 3000g
Blended fabric clothes / Approximately 800g
Jackets Cotton Approximately 800g
Jeans / Approximately 800g
Overalls Cotton Approximately 950g
Ladies Pyjamas / Approximately 200g
Shirts / Approximately 300g
Socks Blended fabrics Approximately 50g
T-Shirts Cotton Approximately 300g
Underwear Blended fabrics Approximately 70g
LOAD REFERENCE
CARE CHART
Resistant material
Delicate fabric
Washable at 95 °C
Washable at 60 °C
Washable at 40 °C
Washable at 30 °C
Hand wash
Dry clean only
Wool Seal
Bleachable in cold water
Do not bleach
Iron at 200 °C
Iron at 150 °C
Iron at 100 °C
Don't iron
Dry cleaning with any solvent
Dry cleaning with pericloride
Dry cleaning with aviation fuel
Don't dry clean
Dry fl at
Hung to dry
Dry on clothes hanger
Tumble dry, normal heat
Tumble dry, reduced heat
Don't tumble dry
16
1.
2.
1
.
2.
3.
2.
4.
1.
M
AINTENAN
CE
CLEANING & CARE
AFTER WASHING
Turn off the water supply and pull out electricity plug after each wash.
Open the washer door to prevent formation of moisture and odours. If
the washing machine is left idle for a long period, drain the water in the
machine and replace the drain hose.
CLEANING THE DETERGENT DRAWER
Clean the detergent distribution drawer regularly.
Swing out the drawer, fl ush it clean with water and then replace it.
CLEANING THE MACHINE
Unplug the machine during cleaning and maintenance. Use a soft
cloth dampened with soap liquid to clean the machine case and rubber
components. Do not use organic chemicals or corrosive solvents.
CLEANING THE FILTER
Clean the fi lter once a month:
1.Open the bottom cover.
2.Remove the fi lter by turning counterclockwise.
3.Flush the fi lter clean with running water.
4.Replace the fi lter by turning clockwise and
remount the cover.
Caution:
1.The filter must be in place, or it may lead to leakage.
2.Place a container under the drain pump filter, to collect
any excess water that may come out of the drain pump
when the filter is removed.
17
2.
4.
5.
1.
3.
Quickwash
Wool
Synthetics
Prewash
Delay
Wash Rinse Spin Dry
Extra
rinse
Dry EcoTime Start/
Pause
Power
Temp
Speed
Delay Extra
rinse
Rinse
hold
Eco Start/
Pause
pre-
wash
Rinse SpinWash
Silk
Sport
Quick Wash
Rinse
Spin
Drain
ON
OFF
M
AINTENAN
CE
WATER INLET AND INLET FILTER
To prevent blockage to the water supply by ingress of foreign substances, clean the water inlet and inlet
fi lter regularly.
MOVING THE MACHINE
If the machine is to be moved to a distant location, replace the transportation locks removed before installation to prevent damage as
shown below.
Remove the blanking plugs.1.
Remove the back cover2.
Insert the synthetic stabilisers and the transportation bolts.3.
Tighten the bolts with a spanner.4.
Replace the back cover.5.
LONG PERIODS OF DISUSE
If the washing machine is left idle for a long period, pull out the electrical plug and turn off the water
supply. Open the washer door to prevent formation of moisture and odours. Let the door open while not
used.
18
M
AINTENAN
CE
CODES CAUSES SOLUTIONS
Err1 ¬ Washer door is not properly shut. _ Close the washer door properly
Err2 ¬ Drainage error. _ Clean the fi lter and check the drain hose for block-
age.
Err3 ¬ Temperature sensor error
(Appears at the end of a cycle).
_ Please contact the Service Center.
Err4 ¬ Heater error (Appears at the end of a cycle). _ Please contact the Service Center
Err5 ¬ Water inlet error. _ Check the tap and the water pressure.
Err6 ¬ Motor error. _ Please contact the Service Center.
Err7 ¬ Motor error. _ Please contact the Service Center.
Err8 ¬ Water exceeds protective level. _ Please contact the Service Center.
unb ¬ Laundry is unevenly distributed. _ Redistribute laundry to balance the drum.
End ¬ End of wash cycle.
1:16 ¬ Remaining time is 1 hour and 16 minutes.
0:01 ¬ Remaining time is 1 minute.
60 ¬ Preset washing temperature is 60° C.
-- ¬ Cold wash.
800 ¬ Preset spinning speed is 800rpm.
DISPLAY CODES
DISPLAY CODES AND SPECIAL FUNCTIONS
¬ Control panel lock function: Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a
program. It can no longer be changed by operating buttons or knobs. The washing machine emits an audible signal while the control
panel is locked. To unlock press the "Delay" and "Start/Pause" buttons again for 3 seconds.
¬ Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycle, the pres-
ent settings will be saved and the preset operation will resume when the power is on again.
¬ To cancel a program or select a new program and options during the wash cycles.
a) Press the "Start/Pause" button, then switch off the power and the program is automatically cancelled. Turn the program selector
again to choose another program.
b) If you wish to select an option during the wash cycle, press the "Start/Pause" button, then select the desired option and press the
"Start/Pause" button again.
Note: 1.The Rinse hold function can be selected directly without pressing fi rst the "Start/Pause" button, but before the machine starts
the spin program.
2.Alarm sound can be cancelled if it is needed. Please follow the instruction as below:
Switch on the washing machine and turn the program knob to spin cycle, then press the delay button and hold on for 3 seconds. The
“b OFF” will be displayed on the screen which indicates that alarm sound has been canceled. To operate the above steps again so the
alarm sound can be recovered and the display will show “b ON”
3.CLRF:Too much foam used in wash cycle.Washing machine can eliminate the foam automatically during spin cycle.If the washing
machine fails to eliminate the excessive foam, it will end the cycle without spinning.
19
M
AINTENAN
CE
TROUBLESHOOTING
TROUBLESHOOTING
The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confi rmed.
PROBLEM CAUSES SOLUTIONS
Washing machine fails to
operate.
¬ Poor connection to the power supply.
¬ Power failure.
¬ The washer door is not properly closed.
¬ Machine has not been switched on.
_ Check connection to the power supply.
_ Check the power supply.
_ Close the washer door properly.
_ Make sure the machine is switched on.
Washing machine cannot be
fi lled with water.
¬ The "Start/Pause" button is not pressed.
¬ Water tap is not turned on.
¬ Water pressure is less than 0,03 MPa.
¬ The inlet hose is kinked.
¬ Water supply failure.
¬ The program knob is not properly set.
¬ The washer door is not properly closed.
¬ The inlet hose fi lter is blocked.
_ press the "Start/Pause" button.
_ Turn on the water tap.
_ Check water pressure.
_ Check the inlet hose.
_ Ensure the water supply.
_ Set the program knob properly.
_ Close the washer door properly.
_ Unblock the inlet hose fi lter.
Machine is draining while
being fi lled.
¬ The height of the drain hose is below 80 cm.
¬ The drain hose is in water.
_ Install drain hose within 80-100 cm of height.
_ Make sure the drain hose is not in water.
Drainage failure. ¬ Drain hose is blocked.
¬ Drain hose end is higher than 100 cm above
the fl oor level.
¬ The fi lter is blocked.
_ Unblock the drain hose.
_ Make sure the drain hose end is lower than
100 cm above fl oor level.
_ Unblock the fi lter.
Strong vibration while
spinning.
¬ Not all transportation bolts have been removed.
¬ Washing machine is located on an uneven
surface or is not level.
¬ Machine load is over 7 kg.
_ Remove all transportation bolts.
_ Make sure the washing machine is on
an even surface and levelled.
_ Reduce amount of laundry in the drum.
Operation stops before
completing wash cycle.
¬ Water or electricity failure.
¬ Washing machine is in rinse hold cycle.
¬ Washing machine gives an error message.
_ Check the power supply.
_ Press the rinse hold button
_ Check display codes.
Excessive foam in the
drum, which is spilled to the
distribution drawer.
¬ The detergent is not a low-foaming type or for
manual wash.
¬ Excessive use of detergent.
_ Check if your detergent is appropriate.
_ Reduce amount of detergent in the distribution
drawer.
Automatic adjustment of the
washing time.
¬ The washing program duration will be adjusted
according to the laundry load and the initial water
temperature.
_ This is normal and doesn't affect the
functionality.
Spinning fails ¬ Unbalance of the laundry _ Add clothes or run a spinning program again.
Haier Europe Trading S.r.l.
Via De Cristoforis 12
21100 Varese - Italy
Tel + 39 0332 24511
Fax +39 0332 245146
E-mail [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Haier HW–D1270TVE ME User manual

Haier
Brand
Haier
Model
HW–D1270TVE ME
Category
Washing machines
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents