Directed Electronics 300HF User manual

Category
Car alarm
Type
User manual

This manual is also suitable for

Directed Electronics 300HF is a car alarm system that offers a range of features to protect your vehicle from theft and unauthorized access. With its advanced technology, this system provides reliable security and convenience.

The 300HF comes equipped with a primary harness, two 471T remote transmitters, a 504D plug-in Stinger® shock sensor, a 514N Revenger® Soft Chirp® siren, a four-pin shock sensor harness, a two-pin micro LED plug, a two-pin mini blue Valet®/Program plug, a plug-in Status LED, a three-pin two-wire door lock harness, and a plug-in Valet®/Program switch.

This system offers a variety of customizable features, including a double pulse unlock feature, nuisance prevention circuitry, and Valet® mode. It also includes a table of zones for easy reference.

Directed Electronics 300HF is a car alarm system that offers a range of features to protect your vehicle from theft and unauthorized access. With its advanced technology, this system provides reliable security and convenience.

The 300HF comes equipped with a primary harness, two 471T remote transmitters, a 504D plug-in Stinger® shock sensor, a 514N Revenger® Soft Chirp® siren, a four-pin shock sensor harness, a two-pin micro LED plug, a two-pin mini blue Valet®/Program plug, a plug-in Status LED, a three-pin two-wire door lock harness, and a plug-in Valet®/Program switch.

This system offers a variety of customizable features, including a double pulse unlock feature, nuisance prevention circuitry, and Valet® mode. It also includes a table of zones for easy reference.

300HF
Installation Guide
Table of Contents
Experienced security installers may skip to Pg. 8, but read
all the italicized sections, as they describe changes and/or new features.
Installation Points to Remember Page 2
Deciding on Component Location 3
Finding the Wires you Need 5
Step-by-step meter instructions!
Making your Wire Connections 7
Primary Harness Diagram 8
Wire Connection Guide 9
Plug in LED and Valet
®
/Program Switch 11
Four-pin Shock Sensor Harness 11
Bypassing Sensor Inputs 12
Door Lock Wiring Diagrams 12-15
Transmitter/Receiver Learn Routine
16
Two-vehicle Operation with Single Transmitter 17
Operating-Settings Learn Routine
18
New Double Pulse Unlock Feature
Feature Descriptions 20
Nuisance Prevention
®
Circuitry 21
Valet
®
Mode 21
Table of Zones 22
Troubleshooting 22
© 1999 Directed Electronics, Inc. Vista, CA
Directed Electronics, Inc.
N430 9/99
®
2 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
Do not disconnect the battery if the vehicle has an anti-theft-coded radio.If equipped with an air bag, avoid discon-
necting the battery if possible.
IMPORTANT! Many airbag systems will display a diagnostic code through their warning light after they lose
power. Disconnecting the battery requires this code to be erased, a procedure that can require a trip to the
dealer.
Before beginning the installation:
Check with the customer on Status LED location.
Remove the domelight fuse.This prevents accidentally draining the battery.
Roll down a window to avoid being locked out of the car.
After the install:
Test all functions.The "Using Your System" section of the Owner's Guide is very helpful when testing.
When testing, don’t forget that this system is equipped with Nuisance Prevention
®
Circuitry. NPC
can
bypass trigger zones, making them appear to stop working. (See page 21)
Two 471T
remote
transmitters
514N
Revenger
®
Soft Chirp
®
siren
Plug-in
Status LED
Plug-in
Valet
®
/Program
switch
INSTALLATION POINTS TO REMEMBER
Primary
harness
H1
3-pin
2-wire
door
lock
harness
504D Plug-in
Stinger
®
shock
sensor
2-pin
mini
blue
Valet
®
/
Program
plug
2-pin
micro
LED
plug
4-pin shock
sensor plug
© 1999 Directed Electronics, Inc.Vista, CA 3
N430 9/99
Step One:
Deciding on Component Locations
Siren
Some things to remember when mounting the siren:
Keep it away from heat sources. Radiators, exhaust manifolds, turbochargers, and heat shields are all
things to avoid.
Mount it where a thief cannot easily disconnect it, whether the hood is open or shut.Both the siren and
its wires should be difficult to find.This usually involves disguising the wire to look like a factory harness.
We recommend against grounding the siren to its
mounting screws. Instead, we recommend running both
the red and black wires into the passenger compartment
and grounding to one common point for all devices.After
all, both wires are the same length and come already
bonded together.Whenever possible, conceal your wires
in the factory harnesses or in the same style loom as the
factory.
When possible, put the siren on the same side of the
vehicle as the control module, where its wires will reach
the control module’s wires without extending them.
Always run the wires through the center of a grommet,
never through bare metal!
Point the siren down so water does not collect in it.
Control Module
Never put the control module in the engine compartment!
The first step in hot-wiring a vehicle is removing the driver's side under-dash panel to access the starter and ignition
wires.If the control module is placed just behind the driver's side dash it can easily be disconnected.
When locating the control module, try to find a secure location that will not require you to extend the harnesses’
wires (they are 1.5 meters long). Keep it away from the
heater core (or any other heat sources) and any obvious
leaks.
The higher the control module is in the vehicle, the better
the transmitter range will be. If you put the control module
under a seat or inside a metal dashboard, range will suffer,
and you may wish to add a 542T Range Extending
Antenna (available separately).
Some good control module locations: Above the glove box,
inside the center console, above the under-dash fuse box,
above the radio, etc.
4 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
Stinger
®
Doubleguard
®
Shock Sensor
Never put the Stinger
®
in the engine compartment!
Find a spot close to the control module so that the wires do not need to be extended. Keep it away from the heater
core (or any other heat sources) and any obvious leaks.
How the Stinger is mounted is the most important factor in its performance.We recommend two mounting methods:
Using double-sided tape or hook-and-loop fastener to mount to a trim panel or an air duct, or wire-tying to a wire
harness. If mounting the sensor where it cannot be easily reached for adjustment, hook-and-loop fastening tape
(such as Velcro) is recommended for ease of removal for future adjustments.
NOTE: In many vehicles, tying the sensor to a steering column or screwing it to metal will result in poor
sensitivity, especially on the rear of the vehicle.
Valet
®
Program Switch
Ensure that the location you pick for the switch has sufficient clearance to the rear.The switch should be well hidden.
It should be placed so passengers or stored items (such as in a glove box or center console) cannot accidentally hit
it.The switch fits in a 9/32" hole.
This system has Remote Valet
®
.The user can enter and exit Valet
®
Mode without having to reach the Valet
®
/program
switch. DEI
®
introduced this feature so that switch location was less critical in day-to-day use. As long as the
Valet
®
/program switch can be reached to disarm without a transmitter, easy access is not important.
IMPORTANT! When the vehicle is delivered, please show the user where the switches are located and how
to disarm the system with it.
Status LED
Things to remember when positioning the Status LED:
It should be visible from both sides and the rear of the vehicle, if possible.
It needs at least 1/2" clearance to the rear.
It is easiest to use a small removable panel, such as a switch blank or a dash
bezel.Remove it before drilling your 9/32" hole.
Use quick-disconnects near the LED wires if the panel is removable. This lets
mechanics or other installers remove the panel without cutting the wires.
© 1999 Directed Electronics, Inc.Vista, CA 5
N430 9/99
Optional Starter Kill Relay
If Starter Kill Relay or its connections are immediately visible upon removal of the under-dash panel, they can easily
be bypassed.Always make the relay and its connections difficult to discern from the factory wiring! Exposed yellow
butt connectors do not look like factory parts, and will not fool anyone! For this reason, routing the starter kill wires
away from the steering column is recommended.
Step 2:
Finding the Wires You Need
Now that you have decided where each component will be located, you’re going to find the wires in the car that the
security system will be connected to.
IMPORTANT! Do not use a 12V test light to find these wires! All testing described in this manual is
described using a digital multimeter.
Obtaining Constant 12V
We recommend two possible sources for 12V constant:The (+) terminal of the battery, or the constant supply to the
ignition switch. Always install a fuse within 12 inches of this connection.If the fuse also will be powering other
circuits, such as door locks, a power window module, a Nite-Lite
®
headlight control system, etc.; fuse accordingly.
IMPORTANT! Do not remove the fuse holder on the red wire.It ensures that the control module has its own
fuse, of the proper value, regardless of how many accessories are added to the main power feed.
Finding the 12V Switched Ignition Wire
The ignition wire is powered when the key is in the run or start position.This is because the ignition wire powers the
ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer).Accesso-
ry wires, on the other hand, lose power when the key is in the start position to make more current available to the
starter motor.
How to find (+)12V ignition with your multimeter:
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the ignition wire. The steering column
harness or ignition switch harness is an excellent place to find this wire.
4. Turn the ignition key switch to the run position.If your meter reads (+)12V, go to
the next step. If it doesn’t, probe another wire.
5. Now turn the key to the start position.The meter display should stay steady, not
dropping by more than a few tenths of a volt.If it drops close to or all the way to
zero, go back to step 3. If it stays steady at (+)12V, you have found an ignition
wire.
6 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
Finding a (+) Parking Iight Wire
The (+) parking light wire is often found near the switch.Many cars have the switch built into the turn signal lever, and
in these cars the parking light wire can be found in the steering column.The same wire is often available in the kick
panel or running board.
NOTE: Many Toyotas, as well as many other Asian vehicles, send a (-) signal from the switch to a relay.The
relay then sends 12V(+) to the bulbs.Whenever you have difficulty finding a (+) parking light wire near the
switch, simply test the wires at any switch or control panel which is lit by the instrument panel lighting.
Remember, you need a (+) parking light wire that does not vary with dimmer setting.
How to find a (+) parking light flash wire with your multimeter
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the parking light wire. Usually,
the area near the headlight/parking light switch is an excellent area
to start, as is the kick panel.
4. Turn on the parking lights. If your meter shows (+)12V, turn off the
parking lights and make sure it goes back to zero.
5. If it does return to zero, turn the parking lights back on and, using the dash light dimmer control, turn the
brightness of the dash lights up and down. If the meter changes more than a volt when using the
dimmer, look for another wire.If it stays relatively close to (+)12V, you have found your parking light wire.
Finding the Door Pin Switch Circuit
The best places to find the door switch wire are:
At the pin switch:When testing at the pin switch, check the wire to ensure that it “sees” all the doors.Often,
the passenger switch will cover all the doors even if the driver’s switch will not.
At the dome light:This may not be your best choice if the vehicle has delayed domelight supervision, but it
will work in many Hondas, or any vehicle with completely diode-isolated pin switches.
Once you have determined the wire color, the easiest place to connect to the wire is often at the kick panel, at the
windshield pillar, or in the running board. When an easy location is not available, running a wire to the domelight
itself is often the best solution.
How to find a door pin switch trigger wire with your multimeter:
1. Set to DCV or DC voltage (12V or 20V is fine).
2. In most Fords, fasten the (-) probe of the meter to chassis ground. In most other cars, fasten the (+)
probe of your meter to (+)12V constant.
3. Probe the wire you suspect of being the door trigger wire. If the meter reads (+)12V when any door is
opened, you have found a trigger wire.
NOTE: Make sure the wire you use “sees” all the doors! Some newer GM vehicles lack standard-type pin
switches.The dome light in these vehicles is turned on when the door handle is lifted.These usually have a
blue/white or white coming out of the door into the kick panel which will provide a (-) trigger for all doors.
Some GM vehicles (some Cavaliers, Grand Ams, etc.) have a yellow wire coming out of the door which
provides a (+) door trigger.
© 1999 Directed Electronics, Inc.Vista, CA 7
N430 9/99
How to find the (+)12V starter wire with your multimeter:
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the starter wire. The steering
column is an excellent place to find this wire. Remember you do not
need to interrupt the starter at the same point you test it. Hiding your
starter kill relay and connections is always recommended.
4. Turn the ignition key switch to the start position. Make sure the car is not in gear! If your meter reads
(+)12V, go to the next step.If it doesn’t, probe another wire.
5. Cut the wire you suspect of being the starter wire.
6. Attempt to start the car.If the starter engages, reconnect it and go back to step 3.If the starter does not
turn over, you have the right wire.
Step 3:
Making Your Wire Connections
Before making your connections, plan how your wires will be routed through the vehicle. For instance, the yellow
ignition input, the red 12V constant input, and the orange ground-when-armed output (for the optional starter kill
relay) will often be routed together to the ignition switch harness.In order to keep the wiring neat and make it harder
to find, you may wish to wrap these wires together in electrical tape or conceal them in tubing similar to what the man-
ufacturer used.
There are two acceptable ways of making a wire connection:Solder connections and crimp connectors.When prop-
erly performed, either type of connection is reliable and trouble-free. Regardless of whether you solder your
connections or you use mechanical-type crimp-on connections, ensure that all connections are mechanically sound
and that they are insulated.
Cheap electrical tape, especially when poorly applied, is not a reliable insulator. It often falls off in hot weather. Use
good-quality electrical tape or heat shrink.
Never
twist-and-tape the wires together without soldering.
Never
use “fuse taps, as they can damage fuse box terminals.
If you use tapping connectors such as 3M T-Taps (not to be confused with Scotch-Locks), avoid using them in
higher-current applications (constant 12V, ground, etc.). Some tapping connectors are inferior in quality and should
be avoided.
8 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
PRIMARY HARNESS DIAGRAM H1, 12-PIN CONNECTOR
ORANGE (-) 500 MA ARMED OUTPUT
WHITE (+) LIGHT FLASH OUTPUT
WHITE/BLUE NOT USED
BLACK/WHITE NOT USED
GREEN (-) DOOR TRIGGER INPUT, ZONE 3
BLUE (-) INSTANT TRIGGER INPUT, ZONE 1
VIOLET (+) DOOR TRIGGER INPUT, ZONE 3
BLACK (-) CHASSIS GROUND INPUT
YELLOW (+) SWITCHED IGNITION INPUT, ZONE 5
BROWN (+) SIREN OUTPUT
RED (+) CONSTANT POWER INPUT
RED/WHITE (-) 200
MA CHANNEL 2 VALIDITY OUTPUT
H1/1
H1/2
H1/3
H1/4
H1/5
H1/6
H1/7
H1/8
H1/9
H1/10
H1/11
H1/12
© 1999 Directed Electronics, Inc.Vista, CA 9
N430 9/99
WIRE CONNECTION GUIDE
H1/1 ORANGE
(-) ground-when-armed output: This wire supplies a (-) 500 mA ground as long as the system is
armed.This output ceases as soon as the system is disarmed.This wire is used to control the optional 8618 starter
kill relay.The 8617 relay assembly may also be used as shown in the diagram below.
NOTE: If connecting the orange wire to control another module, such as a 529T or 530T window controller,
a 1 amp diode (type 1N4004) will be required. Insert the diode as shown below.
IMPORTANT! Never interrupt any wire other than the starter wire.
H1/2 WHITE
(+) light flash output: This wire should be connected to the (+) parking light wire, as described in the
“Finding the wires you need”section of this manual.This output is protected with a 7.5 amp fuse.Never increase the
value of the light flash fuse. If more current is required, use an external relay.
10 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
H1/5 GREEN
(-) door trigger or
H1/7 VIOLET
(+) door trigger input: If the door switch wire you found is (-) when the
door is open, connect the GREEN wire to it. If the door switch wire you found is (+) when the door is open, use the
VIOLET wire instead.
IMPORTANT! Test to make sure this wire "sees" all doors!
H1/6 BLUE
(-) instant trigger:This input will respond to a (-)input with an instant trigger.It is ideal for hood and trunk pins and will
report on zone one.If connecting several inputs to this wire.They Should be diode isolated as shown below
.
H1/8 BLACK
(-) chassis ground connection. Connect this wire to bare metal, preferably with a factory bolt rather
than your own screw (screws tend to either strip or loosen with time). We recommend grounding all your compo-
nents to the same point in the vehicle.
H1/9 YELLOW
(+) ignition input. Connect this wire to an ignition wire as described on page 5.This wire must show
+12V with the key in run position and during cranking.Take great care that this wire cannot be shorted to the chassis
at any point.
H1/10 BROWN
(+) siren output: Connect this to the red wire of the Revenger
®
siren. Connect the black wire of the
siren to (-) chassis ground, preferably at the same point you grounded the control module’s H1/8 BLACK wire.
NOTE: REMOVE ANY PAINT
BELOW RING CONNECTOR
© 1999 Directed Electronics, Inc.Vista, CA 11
N430 9/99
H1/11 RED
(+)12V constant power input: Before connecting this wire, remove the supplied fuse. Connect to the
battery positive terminal or the constant 12V supply to the ignition switch as described on Page 5.
NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 10A fuse in the
harness for this purpose.This fuse protects the module itself.
H1/12 RED/WHITE
channel 2, 200mA (-) output:When the system receives the code controlling channel, for longer
than 1.5 seconds, the red/white will supply an output as long as the transmission continues.This is often used to
operate a trunk/hatch release or other relay-driven function.
NOTE: If an instant output is desired, press Button I & II at the same time
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input! The transistorized
output can only supply 200 mA of current, connecting directly to a solenoid, motor, or other high-current
device will cause it to fail.
PLUG-IN LED AND VALET
®
/ PROGRAM SWITCH
These plug into the module.The Status LED plugs into the small two-pin socket, while the Valet
®
/Program Switch
should be plugged into the larger blue two-pin connector.The Status LED fits in a 9/32" hole.
Status LED Valet
®
/Program Switch
FOUR PIN SHOCK SENSOR HARNESS
GREEN
(-) Multiplex input:Inputs shorter than .8 seconds will trigger the Warn Away
®
response, while inputs longer
than .8 seconds will trigger full alarm sequence and report zone two.If installing an optional DEI
®
dual stage sensor,
connect to the GREEN wire as shown below. The diagram below eliminates the need for diodes to isolate the
sensors.
Diagram f
or Adding Optional DEI Dual Stage Sensor to GREEN Wire (zone 2)
BLUE
(-) Multiplex input:Inputs shorter than .8 seconds will trigger the Warn Away response, while inputs longer than
.8 seconds will trigger full alarm sequence and report zone two.
RED, BLACK
: RED is (+)12V constant, BLACK is (-) ground. Do not use these for anything besides the plug in
shock sensor.
12 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
HARNESS 2, (+/-) DOOR LOCK OUTPUTS
This system can control two common power door lock types without any additional parts! With certain vehicles, or if
an actuator is to be installed, either a 451M Door Lock Relay Satellite or two relays will be required.
IMPORTANT! If you mistake a Type C direct-wired system for a Type A positive-pulse system, the module
will be damaged!
T
ype A - (+) 12V Pulses From the Switch to the Factory Relays
The system can control this type of system directly, with no additional parts.The switch will have three wires on it,
and one will test (+)12V constantly.The others will alternately pulse (+)12V when the switch is pressed to the lock
or unlock position.
If you cannot get to the switch, and you find a set of wires that pulse (+)12V alternately on lock and unlock, you must
take care to ensure that it is not a Type C direct-wire system.
Here is a test: Cut the wire which pulses (+)12V on lock, and then operate the switch to unlock.
If all doors unlock, the vehicle uses Type A system.
If you lose all door lock operation in both directions, you are operating the master switch in a Type C system.
If you lose all door lock operation of one or more, but not all motors stop operating, and other doors still work, you
have cut a wire leading directly to one or more motors.You must instead find the actual wires leading to the switch.
BYPASSING SENSOR INPUTS
There are times when you need to temporarily bypass all sensor inputs to the unit, such as when remote starting the
vehicle. Anytime an auxiliary channel output is used, all inputs are bypassed for 5 seconds. During the 5 second
bypass period, ground can be supplied to the H1/6 BLUE wire without triggering the unit.When the 5 second bypass
period ends, if the unit sees ground on the H1/6 BLUE wire, all trigger inputs except the door trigger input will remain
bypassed until 5 seconds after ground is removed from the blue wire.This can be done using the status output of a
551T remote start unit as shown below:
GREEN (-) LOCK, (+) UNLOCK OUTPUT
EMPTY UNLESS USING 451M
BLUE (-) UNLOCK, (+) LOCK OUTPUT
H2/A
H2/B
H2/C
© 1999 Directed Electronics, Inc.Vista, CA 13
N430 9/99
Many domestically-made GM vehicles use Type A locks.However, many more GM vehicles are now Type C than in
previous years.The full-size pickups (1989-up), many of the S10 Blazers, the Corvette, '95 Cavalier/Sunfire 1993 -
and newer, Camaro/Firebird all use Type C door locks, and cannot be controlled without a 451M! Almost all domes-
tically-built Fords are Type C.Ford builds almost no Type A systems.Chrysler builds both Type A and Type C, so use
care.
IMPORTANT! Remember that functions of these wires reverse between Type A and Type B!
T
ype B
- (-) Pulses From the Switch to the Factory Relays
This system is common in many Toyota, Nissan, Honda, Saturn, as well as Ford models with a factory keyless-entry
system (some other Fords also use Type B).
The switch will have three wires on it, and one wire will test ground all the time. One wire will pulse (-) when the
switch locks the doors, and the other wire will pulse (-) when the switch unlocks the doors.This type of system is diffi-
cult to mistake for any other type.
IMPORTANT! Remember that functions of these wires reverse between Type A and Type B!
14 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
Type C - Reversing Polarity
Interfacing with a reversing polarity system requires either two relays or one 451M (not included).
It is critical to identify the proper wires and locate the master switch to interface properly. Locate wires that show
voltage on lock and unlock.Cut one of the suspect wires and check operation of the locks from both switches.If one
switch loses operation in both directions and the other switch operates in one direction only, you have located one
of the target wires.The switch that lost all operation is the master switch.If one switch works both directions and the
other switch works only one direction, you have a Type A system.If both switches still operate, but one or more doors
have stopped responding entirely, you have cut a motor lead. Reconnect it and continue to test for another wire.
Once both wires have been located and the master switch identified, cut both wires and interface as shown below.
IMPORTANT! If these are not connected properly, you will send (+) 12 volts directly to (-) ground, possibly
damaging the alarm or the factory switch.
Type D - Aftermarket Actuators
In order for this system to control one or more aftermarket actuators, a 451M or two relays (optional) are needed.
Vehicles without factory power door locks require the installation of one actuator per door.This requires mounting the
door lock actuator inside the door.Other vehicles may only require one actuator installed in the driver's door if all door
locks are operated when the driver's lock is used.This type of installation is required to operate factory lock systems
in Volvo (except 850), SAAB, and most Mazda, Isuzu and Subaru models.
The fuse used on 12 volt inputs should be 7.5A per motor installed in the vehicle.
IMPORTANT! Do not connect the outputs of the alarm directly to the actuator!
© 1999 Directed Electronics, Inc.Vista, CA 15
N430 9/99
Type E - Mercedes-Benz and Audi (1985 & Newer)
Door locks are controlled by an electrically activated vacuum pump. Some Mercedes and Audis use a Type D
system.Test by locking doors from the passenger key cylinder.If all the doors lock, the vehicle's door lock system can
be controlled with just two relays (optional).The control wire can be found in either kick panel and will show (+)12V
when doors are unlocked and (-) ground when doors are locked.
To interface see diagram below.The system must be programmed for 3.5 second door lock pulses (see
Operation-
Settings Learn Routine
).
Type F - One-Wire System
This system usually requires a negative pulse to unlock, and cutting the wire to lock the door. In some vehicles,
these are reversed.It is found in late-model Nissan Sentras, some Nissan 240SX, and Nissan 300ZX 1992-up.It is
also found in some Mazda MPV and Mitsubishi models.
One relay (optional) is used to interface to this type of system as follows:
16 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
TRANSMITTER/RECEIVER LEARN ROUTINE™
In order to enter Learn Routine
the Valet
®
/Program button must be plugged into the blue port. There is a basic
sequence to remember whenever programming this unit: Door, Key, Choose, Transmit and Release.
1. Door Open a door. Either the H1/5 green or the H1/7 violet door trigger wire must be
connected for the control unit to “see” an open door.
2. Key Turn the ignition on to the run position.The H1/9 yellow switched ignition input must
be connected.
3. Choose Within 15 seconds, press and release the momentary button to select the channel
you wish to program:
Press and Release
To Program
One time Arm/disarm/panic
Two times Channel two output
(Silent Mode
/Remote Valet
®
)
Three times Channel two output (instant)
NOTE: When programming a transmitter button to step three, the assigned button will provide an instant
output on the red/white wire.
Once you have selected the step, press the button once more and hold it.The unit will chirp one, two or three
times depending on the channel selected. Do not release the momentary button.
4.Transmit While holding the momentary button, press the button on the transmitter that you
would like to control the selected receiver channel. One chirp will confirm that the
code has been learned.
5. Release Once the code is learned, the button can be released.
You can step from one step to another by releasing the Valet
®
/program button and tapping it to advance steps and
then holding it.For instance:You have programmed channel one and you want to program channel two.Release the
Valet
®
/program button. Press it one time and release it to advance from step one to step two. Now, press and hold
the button down and the unit will chirp twice.As before, do not release it.
If you want to program channel two (instant) after programming channel one, release the momentary button press
it twice and release it to advance to step three.Then press it once more and hold it.The siren will chirp three times
to confirm it is ready to receive the code from the transmitter.
Learn Routine
will be exited if:
Ignition is turned off
Door is closed
Program button is pressed too many times
More than 15 seconds elapses between steps
One long chirp indicates that Learn Routine
has been exited
© 1999 Directed Electronics, Inc.Vista, CA 17
N430 9/99
TWO-VEHICLE OPERATION WITH SINGLE TRANSMITTER
You can get two-vehicle operation with the transmitters that come with the system.However, you cannot use all the
auxiliary channels of the system (or all the auxiliary channels of the other system), unless using a 485T 4-button
transmitter.
Here's what to do:
1. Using Learn Routine™, program Button I into system # 1 as the arm/disarm button.Do this with all four
remotes.
2. Do the same with system # 2, except program Button II of all four remotes as the arm/disarm button.
If using DEI
®
485T four-button remotes,
all auxiliary channels are available on both vehicles. Before program-
ming, make a list of all channels on each vehicle, and decide which button(s) should control which channel.
For example, if you wanted the top two buttons to control vehicle # 1 and the bottom two buttons to control vehicle
# 2, here is how each system would be programmed:
Vehicle # 1: Button I = arm/disarm.
Button II = trunk release/Silent Mode
.
Button I+II = channel two.(Instant)
Vehicle # 2: Button III = arm/disarm.
Button IV = trunk/release/Silent Mode
.
Button III+IV = channel two.(Instant)
18 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
OPERATING-SETTINGS LEARN ROUTINE™
Many of the operating settings of this unit are programmable.They can be changed whenever necessary through a
computer-based Learn Routine
.The Valet
®
/program push-button switch, plugged into the blue port is used together
with a programmed transmitter to change the settings.To program settings remember: Door, Key, Choose, Transmit
and Release.
1. Door Open a door. Either the H1/5 green or the H1/7 violet door trigger wire must be
connected for the control unit to “see” an open door.
2. Key Turn the ignition on and then back off.The H1/9 yellow switched ignition input must
be connected.
3. Choose Within 15 seconds, press and release the Valet
®
/Program button the number of times
corresponding to the number of the desired feature (see the chart below).The one
chirp settings below are the factory default settings, except where indicated by bold
text.
Feature Number One-chirp Setting Two-chirp Setting
1 Active arming Passive arming
2 Arm/disarm chirps on Arm/disarm chirps off
3 Ignition-controlled door locks Standard door locks
4 Active locking only Passive locking
5 Panic with ignition on No panic with ignition on
6 0.8 second door lock pulses 3.5 second door lock pulses
7 Forced passive arming on Forced passive arming off
8 Automatic engine disable on Automatic engine disable off
9 Double pulse unlock off Double pulse unlock on
10 Code-Hopping
on Code-Hopping
off
11 Siren Horn honk
Once the button has been pressed and released the correct number of times press it once more and hold it.After a
second, the siren will chirp to indicate what step you have accessed. For example, three chirps would indicate
access to the ignition controlled door lock feature.
© 1999 Directed Electronics, Inc.Vista, CA 19
N430 9/99
4. Transmit While holding the Valet
®
/program button, use the arm/disarm button of the
transmitter, to toggle between the one and two chirp settings.The one-chirp
settings are the factory defaults.
5.
Release The button can now be released.
For example, to program the arming mode from active to passive, press and release the Valet/program button once.
Then press and hold it.The siren will chirp once, indicating that the setting can now be changed.While holding the
Valet/program button, press the arm/disarm button on the transmitter. The siren will chirp twice to indicate that
passive arming has been programmed.If this is the desired setting, release the Valet/program button.If this is not the
desired setting, continue to hold the Valet/program button and press the arm/disarm button on the transmitter again.
The siren will chirp once indicating that active arming has been programmed. Once the desired setting has been
selected, release the Valet/program button.
You can advance from step to step by pressing and releasing the Valet/program button the number of times neces-
sary to get from the step you just programmed to the step you wish to access. If you just programmed the
arm/disarm chirps to off and you want to program passive locks, release the Valet/program button, press and
release it twice to step from feature two to feature four.Then press it once more and hold it.The unit will chirp four
times to confirm that you have accessed feature number four.
The Learn Routine
will be exited if:
The ignition is turned on.
The door is closed.
The Valet
®
button is pressed too many times.
More than 15 seconds elapses between steps.
The siren will emit a long chirp when Learn Routine
is exited.
20 © 1999 Directed Electronics, Inc.Vista, CA
N430 9/99
1 – ACTIVE/PASSIVE ARMING: When active arming is selected, the system will only arm when the transmitter is
used. When set to passive, the system will arm automatically 30 seconds after the last door is closed. Passive
arming is indicated by the rapid flashing of the LED when the last protected entry point is closed.
2 – ARM/DISARM CHIRPS ON/OFF: This feature controls the chirps that confirm the arming and disarming of the
system.
3 – IGNITION CONTROLLED DOOR LOCKS ON/OFF: When turned on, the doors will lock three seconds after
the ignition is turned on and unlock when the ignition is turned off.The doors will not lock if the ignition is turned on
with the door open.
4 – ACTIVE/PASSIVE LOCKING: If passive arming is selected in step one, then the system can be programmed to
either lock the doors when passive arming occurs, or only lock the doors when the system is armed via the trans-
mitter. Active locking means the system will not lock the doors when it passively arms. Passive locking means that
the system will lock the doors when it passively arms.
5 – PANIC WITH IGNITION ON: This step controls whether or not the panic mode is available with the ignition on.
In some states, there are laws prohibiting a siren sounding in a moving vehicle. This feature makes the system
compliant with these regulations.
6 – DOOR LOCK PULSE DURATION: Some European vehicles, such as Mercedes-Benz and Audi, require longer
lock and unlock pulses to operate the vacuum pump. Programming the system to provide 3.5 second pulses, will
accommodate door lock interface in these vehicles. The default setting is .8 second door lock pulses. See
“Mercedes-Benz and Audi - 1985 and Newer (Type E)” diagram on page 15.
7 – FORCED PASSIVE ARMING ON/OFF: To use this feature, passive arming must be selected in step one.When
turned on, forced passive arming will ensure that the system will passively arm, even if a zone is left open or invalid.
Forced passive arming occurs one hour after the ignition is turned off.
8 – AUTOMATIC ENGINE DISABLE (AED) ON/OFF: AED is a full time, passive starter disable that works inde-
pendently of the security system.If AED is desired, the optional Starter Kill Relay must be installed.When turned on,
the H1/1 orange, ground when armed output will go active 30 seconds after the ignition is turned off.The LED will
flash at half its normal rate when the ignition is turned off to indicate that AED is on and will interrupt the starter in
30 seconds. AED does not occur in Valet
®
Mode and can be bypassed using the emergency override procedure.
The transmitter can be used to disarm AED, however, the system would have to be armed and then disarmed when
using the transmitter.
9 – DOUBLE PULSE UNLOCK OFF/ON: Some vehicles require two pulses on a single wire to unlock the doors.
When the double pulse unlock feature is turned on, the BLUE H2/C wire will supply two negative pulses instead of
a single pulse. At the same time, the GREEN H2/A wire will supply two (+) pulses instead of a single pulse.This
makes it possible to directly interface with double pulse vehicles without any extra parts.
10 – CODE-HOPPING
ON/OFF: The system uses a mathematical formula to change its code each time the trans-
mitter and receiver communicate.This makes the group of bits or “word” from the transmitter very long.The longer
the word is, the easier it is to block its transmission to the unit.Disabling the Code-Hopping feature lets the receiver
ignore the Code-Hopping part of the transmitter word. As a result, the unit may have better range with Code-
Hopping off. If a standard trinary remote is taught to the system, the Code-Hopping feature is not available.
11 – SIREN/HORN HONK: The system can be programmed to output pulses instead of a continuous output when
the system is triggered.This is useful to honk the factory horn in applications where a siren is undesirable.Remem-
ber that the unit is only capable of supplying 1 amp off current.A relay will be required to interface with most factory
horn systems.
FEATURE DESCRIPTIONS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Directed Electronics 300HF User manual

Category
Car alarm
Type
User manual
This manual is also suitable for

Directed Electronics 300HF is a car alarm system that offers a range of features to protect your vehicle from theft and unauthorized access. With its advanced technology, this system provides reliable security and convenience.

The 300HF comes equipped with a primary harness, two 471T remote transmitters, a 504D plug-in Stinger® shock sensor, a 514N Revenger® Soft Chirp® siren, a four-pin shock sensor harness, a two-pin micro LED plug, a two-pin mini blue Valet®/Program plug, a plug-in Status LED, a three-pin two-wire door lock harness, and a plug-in Valet®/Program switch.

This system offers a variety of customizable features, including a double pulse unlock feature, nuisance prevention circuitry, and Valet® mode. It also includes a table of zones for easy reference.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI