GE AJES12DCC User manual

Category
Split-system air conditioners
Type
User manual

GE AJES12DCC is a built-in heat and cool unit with a range of features for efficient climate control. It offers 11,600 BTU cooling and 11,400 BTU heating capacity, providing reliable temperature regulation for your room. With its mechanical controls, you can easily adjust the thermostat to your desired temperature. The four-way air direction ensures even distribution of cool or warm air throughout the space. For added convenience, the unit includes an up-front, washable air filter for maintaining good air quality.

GE AJES12DCC is a built-in heat and cool unit with a range of features for efficient climate control. It offers 11,600 BTU cooling and 11,400 BTU heating capacity, providing reliable temperature regulation for your room. With its mechanical controls, you can easily adjust the thermostat to your desired temperature. The four-way air direction ensures even distribution of cool or warm air throughout the space. For added convenience, the unit includes an up-front, washable air filter for maintaining good air quality.

Total volume and shelf
area are calculated by
the Association of Home
Appliance Manufacturers’
standards.
AJES12DCC
GE
®
230/208 Volt Built-In Heat and Cool Unit
Wall Case Dimensions and Installation Information (in inches)
Listed by
Underwriters
Laboratories
For answers to your Monogram,
®
GE Profile
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Specification Created 1/07
390121
R
Parallel
Perpendicular
Wall Oulets
All wiring including installation of receptacle must be made in
accordance with local electrical codes and regulations.
Electrical outlet should be in reach of line cord.
Note:
Aluminum wiring may pose special problems – consult a
qualified electrician.
115V
15 Amp
230/208V
20 Amp
Tandem
Large Tandem
230/208V
15 Amp
230/208V
30 Amp
Premium, Deluxe and Value Model
Wall Case Dimensions (in inches)
Note: When installing units in through-the-wall applications.
Do not restrict air flow areas.
26
15-5/8
16-7/8
AJT08DG QSART
Note: When installing slide-out chassis units in through-the-wall
applications, keep louvers free. Do not restrict air flow areas.
230/208V
20 Amp
Perpendicular
Total volume and shelf
area are calculated by
the Association of Home
Appliance Manufacturers’
standards.
AJES12DCC
GE
®
230/208 Volt Built-In Heat and Cool Unit
Wall Case Dimensions and Installation Information (in inches)
Listed by
Underwriters
Laboratories
For answers to your Monogram,
®
GE Profile
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Specification Created 1/07
390121
R
Installation Information: A finished opening of 26-1/8" x 15-3/4"
clear of intrusions is required. Keep clearance of 4" from side
walls. Brick veneer or frame walls should have wood studding
surrounding case to provide firm anchoring with screws. Case
can be fastened directly to brick or block walls with screws sunk
in lead expansion shields.
Note: Units should be caulked on all four sides of case to the
building exterior to assure building integrity.
Two Wall Cases for Tenant Option Installation
When the air conditioner is offered as a tenant option, these
wall cases provide protection against outside elements.
RAB47 includes wall case, exterior grille and steel
closure panels.
RAB48 includes wall case, exterior grille, steel closure panel
and two layers of insulation.
Standard Wall Case RAB46
Solid-sided wall case fabricated of galvanized steel with
baked enamel finish. Welded areas are coated with a sealing
compound to help resist rust and corrosion. Polymer gasket
surrounds opening to assure tight weather seal. Aluminum grille
(RAG13) is included. Panels on interior and between case and
grille provide weather protection prior to installation of chassis.
Provide firm anchoring with screws. Case can be fastened
directly to brick or block walls with screws sunk in lead
expansion shields.
Built-in RAC Installation
(Pub. 1-G003 pg. 138) April 30.1993
Make frame if desired or caulk
between case and siding
15-3/4
26-1/8
Frame Construction
Brick Block and Brick
Frame Construction
Fill open cells
with mortar
or insulation
15-3/4
26-1/8
Lintel
Lintel
OUTSIDE INSIDE
16-7/8
Caulking
Drip Rail
Trim Molding
(if desired)
Plaster Line
Built-In Room Air Conditioners
Wall Opening for RAB36/37/38 Case
A finished opening of 26-1/8" x 15-3/4", clear of
intrusions, is required. Keep clearance of 4" from
side walls. Brick veneer or frame walls should have
wood studding surrounding case to provide firm
anchoring with screws. Case can be fastened directly
to brick or block walls with screws sunk in lead
expansion shields.
Flexible Mounting Position
Built-in RAC Installation
(Pub. 1-G003 pg. 138) April 30.1993
Make frame if desired or caulk
between case and siding
15-3/4
26-1/8
Frame Construction
Brick Block and Brick
Frame Construction
Fill open cells
with mortar
or insulation
15-3/4
26-1/8
Lintel
Lintel
OUTSIDE INSIDE
16-7/8
Caulking
Drip Rail
Trim Molding
(if desired)
Plaster Line
Built-In Room Air Conditioners
Wall Opening for RAB36/37/38 Case
A finished opening of 26-1/8" x 15-3/4", clear of
intrusions, is required. Keep clearance of 4" from
side walls. Brick veneer or frame walls should have
wood studding surrounding case to provide firm
anchoring with screws. Case can be fastened directly
to brick or block walls with screws sunk in lead
expansion shields.
Flexible Mounting Position
Built-in RAC Installation
(Pub. 1-G003 pg. 138) April 30.1993
Make frame if desired or caulk
between case and siding
15-3/4
26-1/8
Frame Construction
Brick Block and Brick
Frame Construction
Fill open cells
with mortar
or insulation
15-3/4
26-1/8
Lintel
Lintel
OUTSIDE INSIDE
16-7/8
Caulking
Drip Rail
Trim Molding
(if desired)
Plaster Line
Built-In Room Air Conditioners
Wall Opening for RAB36/37/38 Case
A finished opening of 26-1/8" x 15-3/4", clear of
intrusions, is required. Keep clearance of 4" from
side walls. Brick veneer or frame walls should have
wood studding surrounding case to provide firm
anchoring with screws. Case can be fastened directly
to brick or block walls with screws sunk in lead
expansion shields.
Flexible Mounting Position
Total volume and shelf
area are calculated by
the Association of Home
Appliance Manufacturers’
standards.
AJES12DCC
GE
®
230/208 Volt Built-In Heat and Cool Unit
Listed by
Underwriters
Laboratories
For answers to your Monogram,
®
GE Profile
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Specification Created 1/07
390121
R
Features and Benefits
11,600/11,400 BTU
11,600/9,480 BTU heat
3,680/3,020 Watts heat
• 9.5/9.5 EER
230/208 Volts
• Mechanical controls
• Variable position thermostat
• Four-way air direction
• Up-front, washable air filter
• 2 cool/2 heat/2 fan only speeds
Model AJES12DCC – Soft Gray
  • Page 1 1
  • Page 2 2
  • Page 3 3

GE AJES12DCC User manual

Category
Split-system air conditioners
Type
User manual

GE AJES12DCC is a built-in heat and cool unit with a range of features for efficient climate control. It offers 11,600 BTU cooling and 11,400 BTU heating capacity, providing reliable temperature regulation for your room. With its mechanical controls, you can easily adjust the thermostat to your desired temperature. The four-way air direction ensures even distribution of cool or warm air throughout the space. For added convenience, the unit includes an up-front, washable air filter for maintaining good air quality.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI