Veranda 73014380 Installation guide

Brand
Veranda
Model
73014380
Type
Installation guide
Owner's Manual
Version
1.0
Vinyl Fence
Framed Gate Kits
Assembly and Installation Instructions
PLEASE READ OWNER'S MANUAL COMPLETELY
BEFORE ASSEMBLING YOUR GATE.
34107025BOM V1 1/14
To register your product, please visit: www.barretteoutdoorliving.com/product-registration
Material Checklist:
Phillips Head Screwdriver
Safety Glasses
Vinyl Cement
Line Level
ATTENTION:
Before you assemble the gate:
PLEASE TAKE A COMPLETE INVENTORY OF ALL PARTS USING THE KIT CONTENTS.
DO NOT ATTEMPT TO ASSEMBLE THE GATE IF PARTS ARE MISSING OR DAMAGED.
Please do not return the product to the store, for assistance or replacement parts call:
1-800-336-2383
Tape Measure
Drill
#2 Square Drive Bit
Gate Hardware (Hinges/Latch)
Thank you for choosing the Barrette Outdoor Living Fence
Gate. Please read the instructions completely before
assembling your gate. Retain manual and your dated sales
slip for future reference and warranty claims.
Before You Begin…
Check your local zoning laws.
• Local zoning laws and Home Owners Associations may
regulate the location, style and height of your fence or even
require a permit signoff beforehand.
Contact your local utilities companies.
• You must have the utility companies clearly mark your property
for electrical, gas or water lines to avoid puncturing any
unseen underground utilities.
Pay to mark your property line.
• Being proactive will save you time and money from any
disputes from neighbors.
Gate posts require an internal support system for weight-bearing
purposes and therefore wooden inserts or a post stiffener is
required.
Post Spacing will be determined by gate width and hardware.
Top Rail
Bottom Rail
Gate
Upright
Side
Channels
Full Privacy
Internal
Post Top
Purchased Metal Stiffener
Fence Panel
Screw/Nail Together As Shown
Fence Panel
3/4" Actual Thickness
Purchased 1x6x8'
Cut To 4-5/8"
Purchased 1x4x8'
Cut To 3-1/8"
Top View of Post
Top View of Post
Privacy Gates
Internal
Post Top
Gate
Upright
Gate
Pockets
Lattice Top
Side
Channels
Top Rail
Bottom Rail
Middle Rail
unseen underground utilities.
2
Internal
Post Top
Gate
Upright
Gate
Pockets
Closed Top Picket
Side
Channels
Top Rail
Top Rail
Bottom Rail
Bottom Rail
Middle Rail
Middle Rail
Internal
Post Top
Gate
Upright
Gate
Pockets
Open Top Picket
Side
Channels
3
Installation
1.) Insert aluminum inserts into both gate uprights.
3.) Insert bottom rail into bottom upright route on one side only.
4.) Insert boards starting from left and working right into bottom
rail. Make sure boards with u-channels are on ends of the
gate closest to the uprights.
2.) In the gate kit there will be two boards that are 4
1
⁄
1
⁄
1
8
⁄8⁄
" wide,
make sure these boards are your end boards and add left
and right u-channels onto the ends of these two gate boards.
Make sure one u-channel is on the “groove” side of the board
and one u-channel is on the “tongue” side of the board.
5.) For full privacy gates slide top rail over all boards and insert
top rail into upright route on same side as bottom rail.
For lattice top, open picket top and closed picket top gates
slide middle rail over all boards and insert middle rail into
upright route on same side as bottom rail.
6.) a.) For lattice top gates add side channels onto lattice
panel. Insert lattice panel into the middle rail and
place top rail on top of lattice panel. Insert top rail
into upright route on same side as bottom and
middle rails.
b.) For open picket top gates insert top rail into upright
route on same side as bottom and middle rails. Insert
pickets through top rail into middle rail.
c.) For closed picket top gates insert pickets into middle
rail. Starting on left side and working right, place top
rail onto all pickets. Insert top rail into upright on
same side as bottom and middle rails.
4
Slide second upright onto gates.
a.
b.
b.
c.
7.) Ensure gate is square. Measure from top left corner to bottom right
corner and write down the measurement. Measure from top right corner
to bottom left corner and write down the measurement. Make sure
measurements are equal before installing screws into uprights.
8.) a.) Once gates are square mark screw locations. Make sure to use
measurements below to mark holes for screws.
b.) Privacy gates:
Make sure 4 screws are installed at the intersection of each rail and
upright on both sides of gate according to screw placement below.
A total of 32 screws will be installed.
c.) Lattice top, open picket and closed picket top gates:
On “Leg” side of aluminum “P” channel, install 2 screws into top rail
on both uprights. Install 4 screws into bottom and middle rails on
both uprights according to screw placements below.
On back sides of uprights, hinges will be installed on one side of the
top and bottom rails. On upright opposite hinges, install 2 screws
into top rail, 4 screws into middle and bottom rails. On upright
on same side as hinges, install 2 screws into middle rail. The hinge
screws will be used for top and bottom rails. A total of 32 screws will
be installed, not counting hinge screws.
For 7" rails use the following
measurement for screw placement:
For 5
1
⁄
1
⁄
1
2
⁄2⁄
" rails use the following
measurement for screw placement:
1
1
⁄
1
⁄
1
4
⁄4⁄
"
2
1
⁄
1
⁄
1
2
⁄2⁄
"
6
1
⁄
1
⁄
1
4
⁄4⁄
"
7"
3
⁄
3
⁄
3
4
⁄4⁄
"
1
1
⁄
1
⁄
1
4
⁄4⁄
"
2
1
⁄
1
⁄
1
2
⁄2⁄
"
4
3
⁄
3
⁄
3
4
⁄4⁄
"
5
1
⁄
1
⁄
1
2
⁄2⁄
"
3
⁄
3
⁄
3
4
⁄4⁄
"
5
“P” Channel
“Leg” Side
of Channel
Upright
9.) Using 1/8" drill bit pre-drill screw holes through uprights, aluminum inserts and rails. Install 1" screws into all pre-drilled
screw holes.
11.) Install hinges according to hinge
instructions for privacy gates; make sure hinges are centered between the screws. For all gates, make sure hinges are
installed on upright on the opposite side of the “leg” of the aluminum insert.
Orientation of “P” Aluminum and Hinge Assembly
10.) Install upright caps onto gate uprights.
6
7
Subject to the conditions and limitations set out below, Barrette Outdoor Living warrants that for so long as the
original purchaser of a product manufactured by Barrette Outdoor Living owns that Boerboel Manual Hardware
(the Product) it will be free from all defects due to faulty design, materials or workmanship.
If a defect in the Product appears the purchaser must advise Barrette Outdoor Living within 14 days of discovering
the defect and return the defective item, comprising either the Product or a defective component of the Product
(the ltem), to Barrette Outdoor Living, freight prepaid, together with proof of purchase whereupon
Barrette Outdoor Living will, at its option and cost, repair or replace the defective ltem with the same or an equivalent
Product or component. Barrette Outdoor Living will not be liable for labor or any other costs associated with the
dismantling, return or reassembly of the Product or any frame or structure to which it is af xed.
This warranty does not apply in respect of defects due to or arising from:
(a) normal wear and tear;
(b) the failure to follow any procedures speci ed or recommended by Barrette Outdoor Living for the
installation, operation and maintenance of the Product;
(c) any act or circumstance beyond Barrette Outdoor Livings control including tampering, unauthorized
repairs, misuse, abnormal use, abuse, accident, damage after delivery to the consumer, damage caused
by events beyond human control including but not limited to damage caused by animals or natural events,
surface tarnishing and/or damage to components caused by corrosion or other environmental conditions;
(d) any defect of or in any framework or material supporting the Product; or
(e) the faulty workmanship of any person other than Barrette Outdoor Living, including the installer of
the Product.
This warranty is personal to the original purchaser of the Product or to the  rst consumer where the Product has
been installed by a contractor for the bene t of the consumer and may not be assigned without
Barrette Outdoor Living’s prior written consent.
This warranty gives you speci c legal rights which are in addition to, and do not replace, other rights and remedies
you may have available to you by law and which may vary from state to state.
Except as expressly granted in this warranty or where to do so would contravene a statute:
(a) all other warranties, conditions and representations, whether express or implied by general law, statute or
custom, in relation to the Product and its quality,  tness for purpose and suitability are expressly excluded; and
(b) Barrette Outdoor Living’s liability is excluded for all other loss, damage or injury of any kind whatsoever
(including any direct, indirect or consequential loss or damage, loss of pro ts or loss of opportunity) arising in
connection with the Product, or the supply, condition or use of the Product, including as a result of any
negligence, misrepresentation, or other default on the part of Barrette Outdoor Living, its of cers, employees,
or contractors or otherwise.
For any speci c questions about the Barrette Outdoor Living Warranty or to make a warranty claim please contact
Barrette Outdoor Living by visiting our website www.barretteoutdoorliving.com, emailing or calling 1-800-336-2383.
Limited Lifetime Warranty
To begin your warranty coverage and register your Boerboel Manual Hardware product visit
www.Boerboelgatesystems.com or www.BarretteOutdoorLiving.com
34107025BOM V1 1/14
© 2013 Barrette Outdoor Living • 7830 Freeway Circle • Middleburg Heights, Ohio • 44130
http://www.barretteoutdoorliving.com • 1-800-336-2383
Transferable Limited Lifetime Warranty
What is covered:
Barrette Outdoor Living warrants vinyl and aluminum products to include; vinyl and aluminum fence,
vinyl and aluminum railing and plastic lattice against defects or workmanship for as long as you own your home.
Barrette Outdoor Living will at its option replace the product in question with new product of the same or equivalent value
at no charge. Barrette Outdoor Living warrants these products against peeling, flaking, splintering, corrosion, rusting or
abnormal discoloration under normal use. This warranty extends to the original purchaser or transferee as specified herein
on the products noted above. Separate and distinct warranties for hardware and other products are not covered under
this warranty.
What this warranty does not cover:
This limited warranty does not cover damage resulting from accident, unreasonable
use, neglect, alteration, improper service, improper installation, acts of God or any other causes not arising out of defects in
materials or workmanship. Additionally, this warranty does not cover costs of installation, removal, reinstallation or surface
mold and mildew created by excessive environmental conditions. Any service or repair provided outside the scope of this
limited warranty shall be at Barrette Outdoor Living’s rate and terms then in effect.
What do we do to correct the problems?
Should your Barrette Outdoor Living product prove defective under warranty,
reference the website or call the phone number listed below. Your problem will be assigned a tracking number and an
authorized Barrette Outdoor Living representative will contact you to arrange a convenient time to schedule an onsite
inspection, or request pictures, if need be. If after inspection product is deemed to be manufacturer defect we will make
arrangements to rectify the issue. You must have proof of your purchase in order for the problem to be corrected.
Transferee Coverage:
Warranty coverage will be extended to one transferee on the above listed products with the following
limitations. Transferee must obtain an original or copy of the initial sales receipt (with proof of date) from the previous
owner(s). Additionally, if fence is purchased from a builder or installer, documentation must be supplied that names the
product installed on property and date of transfer.
Registration:
To activate this warranty, the online registration card must be completed and returned to Barrette Outdoor Living
within 30 days of installation.
Additionally, this Warranty does not cover damage associated with surface mold and mildew resulting from environmental conditions
including air pollution, or any other causes not arising out of defects in materials or workmanship by Barrette Outdoor Living.
This Warranty does not cover costs of removal or disposal of product, or reinstallation of replacement product. Any service provided
outside the scope of this limited Warranty shall be at Barrette Outdoor Living’s standard rate and terms then in eff ect.
Barrette Outdoor Living reserves the right to discontinue or modify any of its products, including the color of its products, without
notice to the homeowner/consumer, and Barrette Outdoor Living does not warrant that any replacement material will match or be
identical to the original product as replacement products may vary in color or gloss in comparison to the original product as a result
of normal weathering. If Barrette Outdoor Living replaces any material under this Warranty, it may substitute products designated by
Barrette Outdoor Living to be of comparable quality or price range in the event the product initially installed has been discontinued
or modifi ed.
THIS WARRANTY IS IN LIEU OF ALL CONDITIONS OR WARRANTIES, EXPRESS, OR IMPLIED INCLUDING BUT NOT LIMITED TO
ANY IMPLIED CONDITIONS OR WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THE PART
OF Barrette OR ITS LICENSORS, SOME STATES DO NOT ALLOW THE EXCLUSIONS OF IMPLIED WARRANTIES OR LIMITATIONS
OF HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. IF THE PRODUCT
IS DEFECTIVE PER THE ABOVE COVERAGES, YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT AS
PROVIDED ABOVE. BARRETTE AND ITS LICENSORS SHALL NOT BE LIABLE FOR ANY DAMAGES, LOSS OF USE, LOSS OF PROFITS
OR INTERRUPTION OF BUSINESS WHETHER SUCH ALLEGED DAMAGES ARE BASED IN WARRANTY, TORT, CONTRACT, OR
INDEMNITY. SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. This warranty is valid only in the United States and Canada.
For any specifi c questions about the Barrette Outdoor Living Warranty or to make a warranty claim please contact
Barrette Outdoor Living by visiting our website www.barretteoutdoorliving.com, emailing or calling 1-800-336-2383.
Begin your warranty coverage and register your Barrette Outdoor Living product at
www.BarretteOutdoorLiving.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Veranda 73014380 Installation guide

Brand
Veranda
Model
73014380
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents