Pioneer DEQ-P6600 Installation guide

DEQ-P6600
Pioneer
Brand
Pioneer
Model
DEQ-P6600
Category
Car speakers
Type
Installation guide
INSTALLATION MANUAL
MANUEL D’INSTALLATION
1
2
3
6
5
4
11
12
Fig. 1
Abb. 1
Afb. 1
Fig. 3
Abb. 3
Afb. 3
Fig. 2
Abb. 2
Afb. 2
7
8
<KSNNF> <04D00000>
DEQ-P6600
Printed in Japan
Imprimé au Japon
<CRD3876-A> EW
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen Kabelfarben.
Le code de couleur des câbles utilisé pour ce produit
est nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.
9
10
Fig. 4
Abb. 4
Afb. 4
Note:
• This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
• To avoid shorts in the electrical system, be sure
to disconnect the · battery cable before begin-
ning installation.
• Refer to the owner’s manual for details on con-
necting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
• Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right · speaker leads are common.
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke or becoming damaged.
• When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
• To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a pos-
sibility of short-circuiting if the leads are not
insulated.
• To prevent incorrect connection, the input side of
the IP-BUS or optical cable connector is blue,
and the output side is black. Connect the connec-
tors of the same colors correctly.
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
• To ensure proper heat dissipation of this product,
take special care not to block the cooling fan side
of this product.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
Note:
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
properly.
• Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.
• Install the unit where it does not get in the dri-
ver’s way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.
• When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fittings.
• Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
• Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.
• If this unit is installed in the passenger compart-
ment, anchor it securely so it does not break free
while the car is moving, and cause injury or an
accident.
• If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched
in the mechanism and cause a short circuit.
Installing the unit
Mounting with brackets (Fig. 1)
1. Tapping screw (4 × 12 mm)
2. Screw (4 × 8 mm)
3. Bracket
4. Do not close this area.
5. Drill 2 to 2.5 mm diameter holes.
6. Car mat or chassis
Mounting with velcro tape (Fig. 2)
Thoroughly wipe off the surface before affixing
the velcro tape.
7. Velcro tape
8. Car mat or chassis
Routing the optical cable
Precaution:
• Try not to bend the optical cable sharply. If it is
necessary to bend it sharply, make sure that the
bending radius is at least 25 mm, otherwise the
cable will not transfer signals properly and so
this unit will not work properly.
• Route the optical cable so that nothing heavy
rests on it, and so that it cannot be stepped on or
caught in anything – for instance, a door.
• Make a loop of diameter at least 200 mm with
the remaining optical cable so that the cable does
not get strained.
• When plugging the optical cable into the unit,
use the supplied cable clamps to prevent the
cable from being bent sharply.
• Route the optical cable so that it does not get
caught in moving parts such as the gear shift,
hand brake, or seat sliding mechanism. Keep the
cable away from hot spots, such as near the
heater outlet.
Using the corrugated tube (Fig. 3)
To prevent the optical cable from being strained,
use the corrugated tube after cutting it to the cor-
rect length.
• Insert the optical cable into the cor-
rugated tube.
9. Optical cable
10. Corrugated tube
Mounting the clamp (Fig. 4)
The clamp is used to secure the optical cable
when using it. The other clamp is installed on the
back side of the head unit similarly and used to
secure the optical cable.
1. Insert the clamp in the direction
indicated in the figure, and turn it 90
degrees to lock.
11. Clamp
2. Secure the optical cable.
12. Optical cable
Installation <ENGLISH> Connecting the Units <ENGLISH>
• Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
manuals of both products and connect cords that
have the same function.
Page is loading ...
Page is loading ...
Page is loading ...
Fig. 8
Abb. 8
Afb. 8
Front video output
(FRONT VIDEO OUTPUT)
17. RCA cable (supplied)
RCA cable
(supplied with Head unit)
Head unit
(e.g. DVH-P5000MP)
(sold separately)
IP-BUS cable
(supplied)
19. Optical cable (supplied)
7. Blue
3. Yellow
8. Black
7. Blue
8. Black
27.
15.
7. Blue
30.
31.
32.
Multi-CD player
(sold separately)
26.
3m
3m
3m
33. Brown
Subwoofer output or non fading
output (SUBWOOFER OUTPUT
or NON-FADING OUTPUT)
17. This product
16:9 touchscreen
display (AVD-W6210)
(sold separately)
34.
IP-BUS cable
(supplied with TV tuner)
25.
3. Yellow
Guide speaker output
(GUIDE SP OUTPUT)
10. 21 pin cable
AV Receiver/DVD player
(AVH-P6600DVD)
(sold separately)
14. IP-BUS input
Subwoofer output
or non fading output
(SUBWOOFER OUTPUT or
NON-FADING OUTPUT)
17. This product
4. 26 pin cable input
9. AV-BUS input
Optical cable connection box
(supplied)
16. RCA cable (supplied)
20. Optical cable (supplied)
Guide speaker
(e.g. CD-TS37GP)
(sold separatly)
IP-BUS cable
(supplied)
AV-BUS cable (supplied
with TV tuner)
RCA cable
(supplied with multi-DVD player)
Optical cable
(sold separately)
Hide-away TV tuner
(e.g. GEX-P6400TVP)
(sold separately)
Multi-DVD player
(e.g. XDV-P9—)
(sold separately)
AV Receiver/DVD player
(AVH-P6600DVD) Hide-away unit
(sold separately)
2. 26 pin cable
7. Blue
Navigation unit
(e.g. AVIC-900DVD)
(sold separately)
1.
5.
6.
12. Violet
8. Black
7. Blue
7. Blue
7. Blue
7. Blue
8. Black
8. Black
8. Black
8. Black
8. Black
8. Black
7. Blue
11.
2. 26 pin cable
13.
15.
18.
19.
21.
22.
23.
27.
28.
29.
3m
3m
3m
Yellow
(FRONT VIDEO
OUTPUT)
IP-BUS cable
(supplied with multi-DVD player)
24.
26. Multi-CD player
(sold separately)
Fig. 7
Abb. 7
Afb. 7
1
Fig. 9
Abb. 9
Afb. 9
Fig. 11
Abb. 11
Afb. 11
Fig. 10
Abb. 10
Afb. 10
2
3
4
5
Connecting the power cord (Fig. 5)
1. This product
2. When you connect a power amp (sold separate-
ly), be sure to use the blue/white lead of this unit.
If you use the blue/white lead of the head unit, it
causes noises.
3. Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).
4. Yellow
To terminal always supplied with power regard-
less of ignition switch position.
5. Fuse holder
6. Black (ground)
To vehicle (metal) body.
7. Black/white
8. Black
9. Center speaker
10. Left
11. Right
12. Front speaker
13. White
14. White/black
15. Gray
16. Gray/black
17. Rear Speaker
18. Green
19. Green/black
20. Violet
21. Violet/black
22. Do not connect anything to the speaker leads that
are not connected to speakers.
Connecting to a sold separately
power amp (Fig. 6)
This product can be connected to a sold separate-
ly power amp using the RCA output jacks.
1. This product
2. When you connect a power amp (sold separate-
ly), be sure to use the blue/white lead of this unit.
If you use the blue/white lead of the head unit, it
causes noises.
3. Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).
4. System remote control
5. Front output
6. Rear output
7. Center output
8. Subwoofer output
9. Power amp (sold separately)
10. RCA cables (sold separately)
11. Front speaker
12. Rear Speaker
13. Center speaker
14. Subwoofer
Connecting the Units <ENGLISH>
Connecting the system
Connecting with
AV receiver/DVD player (Fig. 7)
Connecting with DVD Head unit (Fig. 8)
1. Navigation unit (e.g. AVIC-900DVD)
(sold separately)
2. 26 pin cable
3. Yellow
4. 26 pin cable input
5. Guide speaker (e.g. CD-TS37GP)
(sold separately)
6. Guide speaker output (GUIDE SP OUTPUT)
7. Blue
8. Black
9. AV-BUS input
10. 21 pin cable
11. AV Receiver/DVD player (AVH-P6600DVD)
Hide-away unit (sold separately)
12. Violet
13. AV Receiver/DVD player (AVH-P6600DVD)
(sold separately)
14. IP-BUS input
15. Subwoofer output or non fading output (SUB-
WOOFER OUTPUT or NON-FADING OUT-
PUT)
16. RCA cable (supplied)
17. This product
18. Optical cable connection box (supplied)
19. Optical cable (sold separately)
20. Optical cable (supplied)
21. RCA cable (supplied with multi-DVD player)
22. Multi-DVD player (e.g. XDV-P9—)
(sold separately)
23. Yellow (FRONT VIDEO OUTPUT)
24. IP-BUS cable (supplied with multi-DVD player)
25. IP-BUS cable (supplied with TV tuner)
26. Multi-CD player (sold separately)
27. IP-BUS cable (supplied)
28. Hide-away TV tuner (e.g. GEX-P6400TVP)
(sold separately)
29. AV-BUS cable (supplied with TV tuner)
30. Front video output (FRONT VIDEO OUTPUT)
31. Head unit (e.g. DVH-P5000MP) (sold separately)
32. RCA cable (supplied with Head unit)
33. Brown
34. 16:9 touchscreen display (AVD-W6210)
(sold separately)
Connecting and installing the
optical cable connection box
Connecting the optical cable (Fig. 9)
• Connect the optical cable to the
optical cable connection box.
1. Optical Cable
Installing the optical cable
connection box (Fig. 10) (Fig. 11)
• When
installing the optical cable
connection box with the velcro
tape
Install the optical cable connection box
using the velcro tape in the ample
space of the console box.
2. Velcro tape (hard)
3. Velcro tape (soft)
• When installing the optical cable
connection box with the lock tie
Wrap the optical cable and connection
box with the protection tape and fasten
with the power code using the lock tie.
4. Wrap with the protection tape
5. Fasten with the lock tie
Conexión del cable de
alimentación (Fig. 5)
1. Este producto
2. Cuando tenga que conectar un amplificador de
potencia (vendido separadamente), asegúrese de
usar el conductor azul/blanco de esta unidad.
Si utiliza el conductor azul/blanco de la unidad
principal, se producirán ruidos.
3. Azul/blanco
Al terminal de control del sistema del amplifi-
cador de potencia o terminal de control del relé
de antena automática (máx. 300 mA 12 V CC).
4. Amarillo
Al terminal con suministro constatne de electrici-
dad, independientemente de la posición del inter-
ruptor de encendido.
5. Portafusible
6. Negro (masa)
A la carrocería del veículo (parte metálica).
7. Negro/blanco
8. Negro
9. Altavoz central
10. Izquierda
11. Derecha
12. Altavoz delantero
13. Blanco
14. Blanco/negro
15. Gris
16. Gris/negro
17. Altavoz trasero
18. Verde
19. Verde/negro
20. Violeta
21. Violeta/negro
22. No conecte nada a los cables de altavoz que no
se conectan a los altavoces.
Conectando a un amplificador de
potencia vendido separadamente
(Fig. 6)
Este producto puede ser conectado a un amplifi-
cador vendido separadamente usando la toma de
salida RCA.
1. Este producto
2. Cuando tenga que conectar un amplificador de
potencia (vendido separadamente), asegúrese de
usar el conductor azul/blanco de esta unidad.
Si utiliza el conductor azul/blanco de la unidad
principal, se producirán ruidos.
3. Azul/blanco
Al terminal de control del sistema del amplifi-
cador de potencia o terminal de control del relé
de antena automática (máx. 300 mA 12 V CC).
4. Control remoto de sistema
5. Salida delantera
6. Salida trasera
7. Salida central
8. Salida de altavoz de subgraves
9. Amplificador de potencia (vendido separada-
mente)
10. Cable RCA (vendido separadamente)
11. Altavoz delantero
12. Altavoz trasero
13. Altavoz central
14. Altavoz de subgraves
Conexión de las unidades <ESPAÑOL>
Conexión al sistema (Fig. 7)
Conexión con
receptor AV/reproductor de DVD (Fig. 7)
Conexión con unidad principal de DVD
(Fig. 8)
1. Unidad de navegación (AVIC-900DVD, por
exemplo) (vendida separadamente)
2. Cable de 26 clavijas
3. Amarillo
4. Entrada de cable de 26 clavijas
5. Altavoz de guía (ej. CD-TS37GP)
(vendido separadamente)
6. Salida de altavoz de guía (GUIDE SP OUTPUT)
7. Azul
8. Negro
9. Entrada AV-BUS
10. Cable de 21 clavijas
11. Receptor AV/reproductor de DVD
(AVH-P66650DVD)
Unidad oculta-alejada (vendida separadamente)
12. Violeta
13. Receptor AV/reproductor de DVD
(AVH-P66650DVD) (vendido separadamente)
14. Entrada IP-BUS
15. Salida de altavoz de graves secundario o salida
sin atenuación (SUBWOOFER OUTPUT or
NON-FADING OUTPUT)
16. Cable RCA (suministrado)
17. Este producto
18. Caja de conexión de cable óptico (suministrado)
19. Cable óptico (vendido separadamente)
20. Cable óptico (suministrado)
21. Cable RCA
(suministrado con reproductor de Multi-DVD)
22. Reprodutor de Multi-DVD (p. ej. XDV-P9II)
(vendido separadamente)
23. Amarillo (FRONT VIDEO OUTPUT)
24. Cable IP-BUS
(suministrado con reproductor de Multi-DVD)
25. Cable IP-BUS
(suministrado con el sintonizador de TV)
26. Reproductor de Multi-CD
(vendido separadamente)
27. Cable IP-BUS (suministrado)
28. Sintonizador TV oculto-lejos (GEX-P6400TVP,
por exemplo) (vendido separadamente)
29. Cable AV-BUS
(suministrado con el sintonizador de TV)
30. Salida de vídeo frontalt
(FRONT VIDEO OUTPUT)
31. Unidad principal (p. ej. DVH-P5000MP)
(vendida separadamente)
32. Cable RCA (suministrado con unidad principal)
33. Marrón
34. Pantalla de toque 16:9 (AVD-W6210)
(vendida separadamente)
Conexión e instalación de la caja
de conexión de cable óptico
Conexión del cable óptico (Fig. 9)
• Conecte el cable óptico y hilo de
tierra a la unidad principal.
1. Cable óptico
Instalación de la caja de conexión
de cable óptico (Fig. 10) (Fig. 11)
• Cuando instale la caja de
conexión de cable óptico con la
cinta Velcro.
Instale la caja de conexión de cable
óptico usando la cinta Velcro en el
espacio ancho de la caja de la consola.
2. Cinta Velcro (dura)
3. Cinta Velcro (blanda)
• Cuando instale la caja de
conexión de cable óptico con la
atadura de fijación.
Envuelva el cable óptico y la caja de
conexión con la cinta protectora y
apriete con el cable de alimentación
usando la atadura de fijación.
4. Envuelva con la cinta protectora
5. Apriete con la atacura de fijación
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Pioneer DEQ-P6600 Installation guide

DEQ-P6600
Pioneer
Brand
Pioneer
Model
DEQ-P6600
Category
Car speakers
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents