Hitachi CM5SB User manual

CM 5SB

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et

propriétaires avant qu’ils utilisent l’outil motorisé.

Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica.

Este manual debe ser guardado en un lugar seguro.

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool.

This manual should be stored in safe place.

Model Cutter

Modèle Scie à diamant

Modelo Cortadora

00Cover_CM5SB_US 11/26/07, 15:001

Page is loading ...

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL SAFETY RULES

WARNING:

Read all instructions

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust of fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the influence of drugs, alcohol or

medication.

A moment of inattention while operating

power tools may result in serious personal

injury.

01Eng_CM5SB_US 11/26/07, 15:013

English

4

b) Use safety equipment. Always wear eye

protection.

Safety equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch

is in the off position before plugging in.

Carrying power tools with your finger on the

switch or plugging in power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of these devices can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tools operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc., in accordance with these instructions

and in the manner intended for the particular

type of power tool, taking into account the

working conditions and the work to be

performed.

Use of the power tool for operations different

from intended could result in a hazardous

situation.

5) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts.

This will ensure that the safety of the power

tool is maintained.

–WARNING–

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Contact

with a “live” wire will make exposed metal parts

of the tool “live” and shock the operator.

2. ALWAYS wear ear protections.

Exposure to noise can cause hearing

loss.

3. NEVER touch moving parts.

NEVER place your hands, fingers or

other body parts near the tool’s moving

parts.

4. NEVER operate without all guards in place.

NEVER operate this tool without all guards or

safety features in place and in proper working

order. If maintenance or servicing requires the

removal of a guard or safety feature, be sure to

replace the guard or safety feature before resuming

operation of the tool.

5. Use right tool.

Don’t force small tool or attachment to do the job

of a heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

01Eng_CM5SB_US 11/26/07, 15:014

English

5

6. NEVER use a power tool for applications other

than those specified.

NEVER use a power tool for applications other than

those specified in the Instruction Manual.

7. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

8. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

9. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

10. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to youself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure

and tight.

11. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so

that air can freely flow at all times. Check for dust

build-up frequently.

12. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its

nameplate.

If using the power tool at a higher voltage than

the rated voltage, it will result in abnormally fast

motor revolution and may damage the unit and

the motor may burn out.

13. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange

for repairs by a Hitachi authorized service center.

14. NEVER leave tool running unattended. Turn power

off.

Don’t leave tool until it comes to a complete stop.

15. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry thoroughly.

17. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

18. ALWAYS wear a mask or respirator to protect

yourself from dust or potentially harmful particles

generated during the operation.

19. Do NOT use any cutting tool other than a diamond

wheel.

Use the diamond wheel specified in this manual.

20. Don't use it for cutting of metallic materials.

Diamond wheel may be broken or its service life

may be remarkably reduced when it is used for

cutting of metallic materials. Be sure not to use

the wheel for cutting of metals.

21. Do not start the cutter while the diamond wheel

is in contact with the material.

22. Keep the motor interior free of water.

23. Prior to use, be sure to check the diamond wheel

in such details as crack, broken part, bent part and

the like. Don't use a diamond wheel if any of the

above defect is found on the wheel. Also confirm

that no abnormality exists by actual test running.

24. Proceed with cutting operation when full speed

has been reached.

25. Do NOT apply excessive force.

26. When cutting concrete, tile, or stone, the

maximum cutting depth should be held to within

13/64”(5 mm).

27. Never lay down the cutter while the diamond

wheel is revolving.

Also, do not stop the cutter with the diamond wheel

forcibly depressed against the material.

28. Exercise care to position the cutter at a safe, stable

spot when cutting.

29. Take good care of the power tool and keep it clean.

30. Definitions for symbols used on this tool

V ............... volts

Hz ............. hertz

A ............... amperes

no .............. no load speed

W .............. watt

............. Class II Construction

---/min ...... revolutions per minute

FURTHER SAFETY INSTRUCTIONS FOR

ALL SAWS

DANGER!

a) Keep hands away from cutting area and do not

reach underneath the workpiece. Contact with the

wheel will result in injury.

b) Adjust the cutting depth to the thickness of the

workpiece.

c) Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable

platform.

01Eng_CM5SB_US 11/26/07, 15:015

English

6

It is important to support the work properly to

minimize body exposure, wheel binding, or loss

of control.

d) Never use damaged or incorrect wheel washers

or wheel nut.

The wheel washers and wheel nut were specially

designed for your saw, for optimum performance

and safety of operation.

Causes and operator prevention of kickback:

– kickback is a sudden reaction to a pinched,

bound or misaligned wheel, causing an

uncontrolled saw to lift up and out of the

workpiece toward the operator.

– when the wheel is pinched or bound tightly

by the kerf closing down, the wheel stalls and

the motor reaction drives the unit rapidly back

toward the operator.

Kickback is the result of saw misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below:

a) Maintain a firm housing and position your arms

to resist kickback forces.

Position your body either side of the wheel, but

not in line with the wheel.

Kickback could cause the saw to jump backwards,

but kickback forces can be controlled by the

operator, if proper precautions are taken.

b) When wheel is binding, or when interrupting a cut

for any reason, turn off the switch and hold the

saw motionless in the material until the wheel

comes to a complete stop.

Never attempt to remove the saw from the work

or pull the saw backward while the wheel is in

motion or kickback may occur.

Investigate and take corrective actions to eliminate

the cause of wheel binding.

c) When restarting a saw in the workpiece, centre

the wheel in the kerf and check that wheel

segments are not engaged into the material.

If wheel is binding, it may walk up or kickback from

the workpiece as the saw is restarted.

d) Support large panels to minimize the risk of wheel

pinching and kickback.

Large panels tend to sag under their own weight.

Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the

panel.

e) Do not use dull or damaged wheels.

Unsharpened or improperly set wheels produce

narrow kerf causing excessive friction, wheel

binding and kickback.

f) Wheel depth adjusting locking wing nut must be

tight and secure before making cut.

If wheel adjustment shifts while cutting, it may

cause binding and kickback.

DOUBLE INSULATION FOR SAFER

OPERATION

To ensure safer operation of this power tool, HITACHI

has adopted a double insulation design. “Double

insulation” means that two physically separated

insulation systems have been used to insulate the

electrically conductive materials connected to the power

supply from the outer frame handled by the operator.

Therefore, either the symbol “ ” or the words “Double

insulation” appear on the power tool or on the

nameplate.

Although this system has no external grounding, you

must still follow the normal electrical safety precautions

given in this Instruction Manual, including not using the

power tool in wet environments.

To keep the double insulation system effective, follow

these precautions:

䡬

Only HITACHI AUTHORIZED SERVICE CENTER

should disassemble or assemble this power tool,

and only genuine HITACHI replacement parts

should be installed.

䡬

Clean the exterior of the power tool only with a

soft cloth moistened with soapy water, and dry

thoroughly.

Never use solvents, gasoline or thinners on plastic

components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_CM5SB_US 11/26/07, 15:016

English

7

Diamond wheel

Push button

Housing

Tail cover

Side handle

Switch

Fig. 1

Dust collection

cover

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safey

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ from those on your

own power tool.

NAME OF PARTS

Motor Single-Phase Series Commutator Motor

Power Source Single-Phase 120 V AC 60 Hz / DC

Current 8 A

No-Load Speed 10,000/min

Max. cutting depth 1-3/16”(30mm)

Diamond wheel

5”(125mm) external dia. × 5/64”(2.0mm) thickness

× 7/8”(22.2mm) internal dia.

Weight (without cord) 6.39 lbs (2.9kg)

SPECIFICATIONS

01Eng_CM5SB_US 11/26/07, 15:017

English

8

ASSEMBLY AND OPERATION

APPLICATIONS

䡬

Cutting or scribing concrete

䡬

Cutting or scribing tile

䡬

Cutting or scribing stone

䡬

Cutting or scribing roof tile

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized

conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the

plug is connected to a receptacle while the switch

is in the ON position, the power tool will start

operating immediately and can cause serious

injury.

3. Extension cord

When the work area is far away from the power

source, use an extension cord of sufficient

thickness and rated capacity. The extension cord

should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or

repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the

receptacle must be repaired. Contact a licensed

electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause

overheating, resulting in a serious hazard.

5. Checking and installing the diamond wheel

Check the diamond wheel is a specified one and is

not cracked, broken or bent. Check the diamond

wheel is installed securely. For installation, refer

to “Installing/removing diamond wheel”.

6. Fitting and adjusting the dust collection cover

(Fig. 2)

The dust collection cover is a protective device to

prevent injury should the diamond wheel shatter

during operation. Ensure that the cover is properly

fitted and fastened before commencing cutting

operation.

By slightly loosening the setting screw, the dust

collection cover can be turned and set at any

desired angle for maximum operational

effectiveness. Ensure that the setting screw is

thoroughly tightened after adjusting the dust

collection cover.

7. Confirm the spindle lock mechanism

Confirm that the spindle lock is disengaged by

pushing push button two or three times before

switching the power tool on (See Fig. 1).

8. Cutting depth adjustment (Fig. 3)

Lowering the wing nut will loosen and raising it

will tighten.

Loosening the wing nut and moving the slide guide

will allow adjustment of the cutting depth.

CAUTION:

●

Leaving the wing nut loosened may result in

injury. Securely tighten the wing nut after

adjusting the cutting depth.

●

When the cutting depth exceeds 13/64” (5mm),

concrete, and so on must be cut in two steps.

Never try to cut in one step; otherwise, the motor

is liable to be overloaded and damaged may result.

Also, cutting efficiently will be lower in such an

instance.

Screw

Dust

collection

cover

Fig. 2

Wing nut

Slide

guide

Fig. 3

01Eng_CM5SB_US 11/26/07, 15:018

English

9

MOUNTING AND DISMOUNTING THE

DIAMOND WHEEL

CAUTION:

●

Be sure to disconnect the attachment plug from

the power receptacle to avoid serious trouble.

1. Mounting the diamond wheel

(1) Remove the cover (A).

(2) Thoroughly remove dust accumulated on the

spindle and washers.

(3) As shown in Fig. 5. the concave portions of

wheel washer and wheel nut must be on the

diamond wheel side.

(4) Thoroughly clamp the wheel nut.

2. Dismounting the diamond wheel

Use the provided wrench to remove the wheel nut.

(Fig. 5)

CAUTION:

●

A diamond wheel for mounting on this equipment

must have 7/8” (22.2mm) internal diameter. No

other sized diamond wheel should be used.

●

Always use the provided wrench to secure the

wheel nut.

Fig. 5

Switch

Push button

(Spindle lock)

Side handle

Spindle

Screw

Dust

collection

cover

Wheel washer

Diamond

wheel

Wheel

nut

Wrench

Cover (A)

CUTTING PROCEDURES

1. Cutting procedures (Fig. 6)

(1) Place this tool on the material to be cut and align

the cutting line and the diamond wheel.

The cutting can be performed smoothly if you cut

straight ahead on the cutting line in the initial cut.

(2) Turn on the switch when the diamond wheel is

not touching the material to be cut.

INSTALLING DUST COLLECTION HOSE

When cutting a material which generates cutting dust,

use the dust collection hose as follows:

(1) Remove the rubber cap and install the accessory

adapter. (Fig. 4)

(2) Install the dust collector hose for the power tool in

the accessory adapter. (Fig. 4)

CAUTION:

●

Always install a rubber cap on the dust collection

adapter when the dust collection hose is not used.

Fig. 4

Dust collection

hose

Adapter

Cutting line

Fig. 6

2. Precautions immediately after finishing operation

After switching off the machine, do not put it down

until the depressed center wheel has come to a

complete stop. Apart from avoiding serious

accidents, this precaution will reduce the amount

of dust and swarf sucked into the machine.

01Eng_CM5SB_US 11/26/07, 15:019

English

10

CAUTION:

●

Always check the diamond wheel before starting

work. Never use a diamond wheel which is

cracked, broken or bent.

●

Do not apply water or coolant to the diamond

wheel.

●

Start cutting only when diamond wheel reaches

its maximum speed.

●

If the diamond wheel seizes or there is any

abnormal noise, immediately turn the power off.

●

Never use the diamond wheel to cut zigzag or

curved lines. Never use the side surface of the

diamond wheel. Never use to perform inclination

cutting.

MAINTENANCE AND INSPECTION

WARNING:

Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance

and inspection.

Using cracked, deformed or damaged wheels can lead to wheel breakage and resulting serious

injury.

1. Inspecting the diamond wheel

Since use of a dull diamond wheel will cause motor

malfunctioning and degraded efficiently, replace

with a new one without delay when abrasion is

noted.

2. Inspecting the screws

Regularly inspect all screws and ensure that they

are fully tightened. Should any of the screws be

loosened, retighten them immediately.

WARNING:

Using this cutter with loosened

screws is extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the

winding does not become damaged and/or wet

with oil or water.

4. Inspecting the carbon brushes (Fig. 7)

The motor employs carbon brushes which are

consumable parts. Replace the carbon brush with

a new one when it becomes worn to its wear limit.

Always keep carbon brushes clean and ensure that

they slide freely within the brush holders.

Fig. 7

Wear limit

0.24" (6mm)

No. of carbon

brush

0.67" (17mm)

88

CAUTION:

●

Using this cutter with a carbon brush which is

worn in excess of the wear limit will damage the

motor.

NOTE:

Use HITACHI carbon brush No. 88 indicated

in Fig. 7.

䡬

Replacing carbon brushes:

(1) Loosen the D4 tapping screw retaining the tail

cover and remove the tail cover.

(2) Use the auxiliary hexagonal wrench or small

screwdriver to pull up the edge of the spring that

is holding down the carbon brush. Remove the

edge of the spring toward the outside of the brush

holder.

●

If excessive force is applied to the diamond wheel

to make it align with the cutting line during

cutting, this might not only overload the motor

and cause burn damage but may also overheat

the diamond wheel and shorten the service life.

●

Take care not to allow the power cord to come

into contact with the diamond wheel during

operation.

●

When the work is completed, turn the power off

and disconnect the power plug from the

receptacle.

01Eng_CM5SB_US 11/26/07, 15:0110

English

11

(3) Remove the end of the pig-tail on the carbon brush

from the terminal section of brush holder and then

remove the carbon brush from the brush holder.

(1) Insert the end of the pig-tail of the carbon brush in

the terminal section of brush holder.

(2) Insert the carbon brush in the brush holder.

(3) Use the auxiliary hexagonal wrench or small

screwdriver to return the edge of the spring to the

head of the carbon brush.

(4) Mount the tail cover and tighten the D4 tapping

screw.

Carbon

brush

Brush

holder

Spring

Fig. 8

5. Service and repairs

All quality power tools will eventually require

servicing or replacement of parts because of wear

from normal use. To assure that only authorized

replacement parts will be used, all service and

repairs must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

6. Service parts list

CAUTION:

Repair, modification and inspection

of Hitachi Power Tools must be

carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if

presented with the tool to the

Hitachi Authorized

Service Center when requesting

repair or other maintenance. In the

operation and maintenance of

power tools, the safety regulations

and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest

technological advancements.

Accordingly, some parts (i.e. code numbers and/

or design) may be changed without prior notice.

ACCESSORIES

WARNING:

ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use

replacement parts or accessories which are not intended for use with this tool. Contact

HITACHI if you are not sure whether it is safe to use a particular replacement part or

accessory with your tool.

The use of any other attachment or accessory can be dangerous and could cause injury

or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

䡬

Wrench (Code No. 938332Z) .................................................................................................................................. 1

䡬

Side Handle (Code No. 994322) ............................................................................................................................. 1

䡬

Adapter (Code No. 320994) .................................................................................................................................... 1

OPTIONAL ACCESSORIES........... sold separately

䡬

Diamond Wheel (Segment type) (Code No. 994325, 307007) ............................................................................. 1

䡬

Diamond Wheel (Wave shape type) (Code No. 994326) ..................................................................................... 1

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

01Eng_CM5SB_US 11/26/07, 15:0111

Page is loading ...

34

AB CD

1 320-523 4 D5×25

2 325-053 1

3 321-737 1 “4, 20”

4 301-943 1

5 949-558 1 M8

6 308-541 1

7 308-543 1

8 980-866 1

9 629-T12 1 629T12DDC3PS2-L

10 321-733 1

11 321-734 1

12 360-734U 1 120V “5-7”

13 321-732 1

14 982-021 2 D4×70

15 340-645D 1 120V

16 315-877 1

17 608-VVM 1 608VVC2PS2L

18 321-735 1 “6, 21”

19 303-255 2 M4×10

20 301-944 1

21 321-736 1

22 991-207 3 M4×8

23 936-680 1

24 620-1DD 1 6201DDCMPS2L

25 308-546 1

26 308-545 1

27 307-046 4 M5×16

28 944-109 1 3×3×8

29 994-302 1

30 319-373 1

31 328-743 1

32 308-386 2 M5×16

33 301-949 1

34 327-741 1

35 942-808 1 M6×20

36 328-809 1

37 937-923P 1 5/8"-11UNC

38 328-742 1

39 324-865 1

40 328-841 1

41 314-622 1 M6

42 949-785 1 D6×16

4 3 ––––––––––– 1

44 314-428 1

45 325-050 1

46 999-088 2

47 317-810 2

48 957-754 1

49 308-536 2

50 325-051 1

51 319-319 1

53 325-054 1

54 953-327 1

55 325-052 1

56 328-842 1

57 301-815 2 D4×45

60 980-063 2

61 984-750 2 D4×16

62 937-631 1

6 3 ––––––––––– 1

6 4 ––––––––––– 1

65 328-740 1 “31-36, 38-43, 66”

66 329-497 1

501 320-994 1

502 938-332Z 1

503 994-322 1

504 328-845 1

AB CD

English

A: Item No.

B: Code No.

C: No. Used

D: Remarks

Français

A: No. élément

B: No. code

C: No. utilisé

D: Remarques

Español

A: N

°

. îtem

B: N

°

. codigo

C: N

°

. usado

D: Observaciones

04Back_CM5SB_US 11/26/07, 15:0334

35

04Back_CM5SB_US 11/26/07, 15:0335

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

AVERTISSEMENT :

La poussière résultant d'un ponçage, d'un sciage, d'un meulage, d'un perçage ou de

toute autre activité de construction renferme des produits chimiques qui sont connus

par l'Etat de Californie pour causer des cancers, des défauts de naissance et autres

anomalies de reproduction. Nous énumérons ci-dessus certains de ces produits

chimiques :

● Plomb des peintres à base de plomb,

● Silice cristalline des briques et du ciment et autres matériaux de maçonnerie, et

● Arsenic et chrome du bois d'oeuvre traité chimiquement.

Le risque d'exposition à ces substances varie en fonction de la fréquence d'exécution de

ce genre de travail. Pour réduire l'exposition à ces produits chimiques, travailler dans un

lieu bien ventilé, et porter un équipement de protection agréé, par exemple un masque

anti-poussière spécialement conçu pour filter les particules microscopiques.

ADVERTENCIA:

Algunos polvos creados por el lijado mecánico, el aserrado, el esmerilado, el taladrado

y otras actividades de construcción contienen sustancias químicas conocidas por le Estado

de California como agentes cancerígenos, defectos congénitos y otros daños

reproductores. Algunos ejemplos de estas sustancias químicas son:

● El plomo de las pinturas a base de plomo,

● El sílice cristalino de los ladrillos y cemento y otros productos de mampostería, y

● El arsénico y el cromo de la madera tratada químicamente.

El riesgo resultante de la exposición varía según la frecuencia con que se realiza este tipo

de trabajo. Para reducir la exposicíon a esta sustancias químicas: trabaje en un lugar bien

ventilado y realice el trabajo utilizando el equipamiento apropiado, tal como las máscaras

para el polvo especialmente diseñados para eliminar las partículas minúsculas.

Issued by

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

Hitachi Koki U.S.A., Ltd.

3950 Steve Reynolds Blvd.

Norcross, GA 30093

Hitachi Koki Canada Co.

450 Export Blvd. Unit B,

Mississauga ON L5T 2A4

712

Code No. C99167362

Printed in Malaysia

04Back_CM5SB_US 11/26/07, 15:0336

Hitachi CM5SB, CM 5SB User manual

Related papers

Other documents