Pulsar PSD12030 Operating instructions

Brand: Pulsar

Model: PSD12030

Type: Operating instructions

Pulsar PSD12030 is a stabilized DC power supply intended for supplying CCTV cameras that require a stabilized voltage of 12V DC. It has a universal AC input voltage range of 90÷264V and a high efficiency of 85%. The output current is 3A at ambient temperatures below 30°C and 2A at 40°C. It has built-in protections against short-circuits, overvoltage, and overload.

The power supply comes with a DC5.5/2.1 plug cable and can be used to power up to 4 or 8 cameras when connected to fuse blocks of the LB4/xx/xx or LB8/xx/xx family. The LED optical signalization indicates the presence of DC voltage.

PSD12030

PSD 12V/3A Desktop type power supply for CCTV

Edition: 9 from 22.01.2018

Supersedes edition: 8 from 01.04.2014

Features of the power supply:

 power output 3A/12VDC

 universal AC input voltage range 90÷264V

 high efficiency 85%

 LED optical signalisation

 standby power <0,3W

 efficiency level: V

 protections:

 SCP short-circuit protection

 overvoltage protection (AC input)

 overload (OLP)

 warranty – 2 year from the production date

1. Technical description.

1.1. General description.

Stabilized DC power supply is intended for supply CCTV cameras that require stabilised voltage of 12V DC.The unit has a

cable with a DC5.5/2.1 plug. When connected to fuse blocks of the LB4/xx/xx or LB8/xx/xx family, the power supply unit can feed

more cameras (max. 4 or 8). The unit is protected against short-circuit and overload.

1.2. Technical parameters.

Supply voltage

90 ÷ 264V AC 50÷60Hz

Current consumption

0,31A@230V AC max.

Supply power

36W max.

Efficiency

85%

Output voltage

12V DC

Output current t

AMB

<30°C

3A - refer to graph 1.

Output current t

AMB

=40°C

2A - refer to graph 1.

Ripple voltage

100mV p-p max.

Short-circuit protection SCP

electronic, automatic recovery

Overload protection OLP

105-150% of power supply, automatic recovery

Optical signalisation

LED – presence of DC voltage

Operation conditions

temperature 0

C÷40

relative humidity 20%...90%, without condensation

Dimensions (LxWxH)

107 x 48 (82) x33 [mm]

Net/gross weight

0,25kg / 0,28kg

Protection class PN-EN 60950-1:2007

II (second)

Lenght of DC cable

1,45m + plug DC5,5/2,1 female

Lenght of AC cable

1,15m + mains plug

Storage temperature

-20ºC...+60ºC

 In order to extend the life of the power supply, the load current of 2A is recommended.

Graph 1. Relation between output current and

ambient temperature (instantaneous load).

Fig.1. Dimension of power supply.

Refer to graph 1

1.3. Accessories.

For power supplies are available accessories - fuse blocks and cable adapter. For details –visit www.pulsar.pl.

2. Installation.

2.1. Requirements.

The power supply shall be mounted by the qualified installer having appropriate (required and necessary for a given country)

permissions and qualifications for connecting (operating) low-voltage installations. The power supply shall be mounted in closed rooms,

according to the environment class II, of the normal air humidity (RH=90% max. without condensation) and the temperature within the

range from 0°C to +40°C.

The power supply shall be mounted in a close casing (a cubicle, a terminal device) and in order to fulfill LVD and EMC

requirements the rules for power supplies, encasing and shielding shall be observed according to application.

2.2. Installation procedure.

1. Connect the DC output to the load/loads.

2. Connect the power supply unit to the AC line. The power supply has to be installed in such way to keep the air flow

around the supply unit.

3. After tests and operation control are performed, the casing (cubicle) shall be closed etc.

3. Maintenance.

Any and all maintenance operations may be performed following the disconnection of the power supply from the power

network. The power supply does not require any specific maintenance procedures, however, in the case of significant level of dust, it

should be cleaned with the compressed air.

WEEE MARK

According to the EU WEE Directive – It is required not to dispose of electric or electronic waste as

unsorted municipal waste and to collect such WEEE separately.

Pulsar

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail: [email protected], [email protected]

http:// www.pulsar.pl, www.zasilacze.pl

Pulsar PSD12030 Operating instructions

Pulsar PSD12030 Operating instructions

Pulsar PSD12030 Operating instructions

Related papers