Pulsar RSUPS54 - v1.0 Operating instructions

Category
PoE adapters
Type
Operating instructions

Pulsar RSUPS54 - v1.0 is a 5-port switch with buffer power supply for 4 IP cameras, designed for rack mounting. It offers uninterruptible power supply, 5 10/100 Mb/s ports with 4 PoE ports supporting IEEE802.3af standard, auto-learning and aging of MAC addresses, wide range of mains supply, battery charging and maintenance control, protections against short-circuit, overload, and excessive discharging, acoustic failure indication, and optical indication for AC, DC, temperature, battery voltage, and alarm.

Pulsar RSUPS54 - v1.0 is a 5-port switch with buffer power supply for 4 IP cameras, designed for rack mounting. It offers uninterruptible power supply, 5 10/100 Mb/s ports with 4 PoE ports supporting IEEE802.3af standard, auto-learning and aging of MAC addresses, wide range of mains supply, battery charging and maintenance control, protections against short-circuit, overload, and excessive discharging, acoustic failure indication, and optical indication for AC, DC, temperature, battery voltage, and alarm.

RSUPS54
v.1.0
5-port switch with buffer power supply
for 4 IP cameras, RACK mounted.
EN
Edition: 3 from 30.03.2017
Supercedes the edition: 2 from 23.02.2017
www.pulsar.pl RSUPS54 RACK POWER
2
Example of use.
CONTENTS:
1. Technical description.
1.1. General description
1.2. Block diagram
1.3. Description of components and connectors
1.4. Specifications
2. Installation.
2.1. Requirements
2.2. Installation procedure
3. Indication of the device operation.
3.1. LED indication of operating status
3.2. Optical indication of the switch operation
3.3. Technical output
3.4. Acoustic indication
4. Operation and use.
4.1. Overload or short circuit of the PSU output
4.2. Battery-assisted operation
4.3. Maintenance
Features:
Uninterruptible power supply of 4 IP cameras
(48VDC)
5 10/100 Mb/s ports
4 PoE ports (data transfer and power supply)
15,4W for each PoE port, supports devices
complaint with the IEEE802.3af standard
Supports auto-learning and auto-aging of MAC
addresses (1K size)
wide range of mains supply AC: 176÷264V AC
battery charging and maintenance control
excessive discharging (UVP) protection
battery output protection against short circuit and
reverse connection
battery charge current: 0,5A
(batteries 2x7Ah / 2x17Ah)
acoustic indication of failure
LED optical indication: AC, DC, TEMP, LoB, ALARM
the ALARM technical output of collective failure
relay type, activated by:
230V AC power loss
low voltage of the PSU (<23V)
too high temperature of the PSU (>70°C)
the PSU failure
protections:
SCP short-circuit protection
overvoltage protection
overload protection OLP
forced cooling (fan)
warranty 2 year from the production date
www.pulsar.pl RSUPS54 RACK POWER
3
1. Technical description.
1.1. General description.
The RSUPS54 is a complete solution for power supply and battery backup of 4 IP cameras (48VDC power
supply) in RACK 19" standard.
The main elements of this system include:
- 5 port PoE switch
- buffer power supply 27,6V unit which can accommodate two 12V batteries
- a converter (DC/DC48125) increasing the voltage to 48VDC (supply of the PoE switch)
In case of mains power loss, a battery back-up is activated immediately. Automatic detection of any devices
powered in the PoE standard is enabled at the 1 4 ports of the switch. The UPLINK port is used to connect another
network device. The LED lights at the front panel indicate the operating status of the device.
The switch is fitted with the ALARM technical output of collective failure. In the case of failure, a LED light is
activated, which is accompanied by switching of relay contacts and acoustic indication.
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to
supply a separate power cable for each device. This method allows supplying other network devices, such as IP phone,
wireless access point or router.
1.2. Block diagram.
Fig.1. The block diagram of the PSU.
1.3. Description of components and connectors.
Table 1. (See Fig. 2)
Element no.
[Fig. 2]
Description
AC OK green LED, indicating the presence of 230V voltage
DC OK green LED, indicating the presence of DC voltage
TEMP red LED, indicating too high temperature of the power supply (>70°C)
LoB red LED, indicating too low battery voltage (<23V)
LED ALARM red LED collective failure indication
BAT battery output
ALARM technical output of collective failure relay
BUZZER, micro switch, turning ON / OFF of acoustic indication
switch in the top position, indication ON
www.pulsar.pl RSUPS54 RACK POWER
4
switch in the down position, indication OFF
PoE port 1÷4 for cameras IP connection (data + power supply)
UPLINK port for recorder (data)
230V AC INPUT, power socket 230V AC, power cable 1,5m included
F
MAINS
, fuse in the supply circuit 230V AC, T 3,15A/250V
Fig. 2. The front power of the power supply unit.
Fig.3. The view of the PSU.
www.pulsar.pl RSUPS54 RACK POWER
5
Fig.4. The view of the switch.
Table 2. (See Fig. 3).
Element no.
[Fig. 4]
Description
LINK - yellow LED - indicating the LAN connection status
PoE - green LED indicating voltage at the PoE port
PWR - green LED indicating the supply voltage of the Switch
UPLINK port for recorder (data)
PoE port 1÷4 for cameras IP connection (data + power supply)
1.4. Specifications.
- parameters of the switch (tab.3)
- electrical parameters (tab.4)
- mechanical parameters (tab.5)
- operation safety (tab.6)
- operating parameters (tab.7)
Parameters of the switch (tab. 3).
Ports
5 10/100Mb/s ports (4 x PoE + 1 x UPLINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802.3af (1÷4 ports), 48VDC / 15,4W at each port *
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Forwarding rate
10BASE-T: 14880pps/port
100BASE-TX: 148800pps/port
Bandwidth
1,6Gbps
Transmission
method
Store-and-Forward
Optical indication of
operation
Switch power supply;
Link/Act;
PoE Status
* The given value of 15,4W per port is the maximum value. The total power consumption should not exceed 48W when all PoE ports are
being used.
Electrical parameters (tab. 4).
Mains supply
176÷264V AC
Current up to
0,7A@230V AC max.
Supply power
62W max.
Output voltage at the PoE ports
48V DC maintained regardless of the state of battery charge
The output current at the PoE ports
4 x 0,3A Ʃ=1A (max.)
Battery charge current
(batteries 2x7Ah / 2x17Ah, connect batteries in
series)
0,5A max. (+/-5%)
Short-circuit protection SCP and overload
protection OLP
105% ÷ 150% of the PSU power, manual restart (failure
requires the disconnection of the DC output)
PSU current consumption
0,2A
Battery circuit protection SCP and reverse
polarity connection
melting fuse
Excessive discharge protection UVP
U<19V (+/-5%) disconnect of connection battery
Optical indication of operation:
LED: AC, DC, TEMP, LoB, ALARM, LINK, PoE
Acoustic operation indication:
Piezoelectric indicator ~75dB/0,3m
The ALARM technical output of collective failure
Relay type: 1A@ 30VDC/50VAC
The F
MAINS
fuse in the 230V power supply circuit
T 3,15A
www.pulsar.pl RSUPS54 RACK POWER
6
Mechanical parameters (tab. 5).
Enclosure dimensions
W=19”, H=2U; 482 x 88 x 265 mm (WxHxD)
Fixation
four-point butt mounting to RACK profiles the set include 4 M6 screws + cage nuts
Net weight
6,0kg / 6,5kg
Enclosure
Steel plate RAL 9005, black
Connectors
230V AC input: the IEC C14 socket with a fuse, power cable 1,5m
(included)
Technical output ALARM: Φ0,5-2,1 (AWG 24-12) 0,5-1,5mm
2
Outputs of cameras PoE: sockets RJ45 8P8C
Data output of the UPLINK recorder: RJ45 8P8C jack
Battery output BAT: 6,3F-2,5
Notes
Forced cooling (fan).
Operation safety (tab.6).
Protection class PN-EN 60950-1:2007
I (first)
Protection grade PN-EN 60529: 2002 (U)
IP20
Electrical strength of insulation:
- between input and output circuits of the PSU (I/P-O/P)
- between input circuit and PE protection circuit (I/P-FG)
- between output circuit and PE protection circuit (O/P-FG)
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500V/DC
Operating parameters (tab.7).
Environmental class
II
Operating temperature
-10ºC...+45ºC
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106
2. Installation.
2.1. Requirements.
The PSU RACK shall be mounted by a qualified installer with appropriate permissions and qualifications for
230V/AC installations and low-voltage installations (required and necessary for a given country). The device shall
be mounted in confined spaces, according to the environment class II, with normal air humidity (RH=90% max.
without condensation) and the temperature from -10°C do +45°C.
Before installation, prepare a Switch'a load balance.
The given value of 15,4W per port is the maximum value referring to a single output. The total
power consumption should not exceed 48W when all PoE ports are being used. The increased demand for
power is particularly evident in the case of cameras with heaters or infrared illuminators - when launching these
features, the power consumption increases rapidly, which may adversely affect the operation of the switch.
As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an
appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be
informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The
electrical system shall follow valid standards and regulations.
www.pulsar.pl RSUPS54 RACK POWER
7
2.2. Installation procedure.
1. Before installation, cut off the voltage in the 230V power-supply circuit.
2. Mount the power supply in a RACK 19" cabinet as shown below:
- Mount M6 cage nuts
- Secure the enclosure with 4xM6 screws
3. Connect the batteries in series/parallel to the + BAT- terminals:
- battery output (+): terminal BAT+
- battery output (-): terminal BAT-
4. Connect the ~230V AC power cord with the IEC C13 plug (included) to the 230V AC power supply and turn on
the power (~230V).
5. Connect the camera cables to the RJ45 connectors (PoE connectors) and connect the recorder to the network
(the UPLINK connector).
6. Make the following technical connections when needed:
ALARM technical output of collective failure indication
7. Check the optical indication of the switch operation.
3. Indication of the device operation.
3.1. LED indication of operating status.
The PSU has 5 LED lights at the front panel:
GREEN LED:
on the PSU is supplied with 230V AC
off no 230V AC supply
GREEN LED:
on DC voltage at the output of the switch mode PSU
off no DC voltage at the output of the switch mode PSU
RED LED:
on failure
off no failure
RED LED:
ON too high temperature of the switch mode power supply
(>70°C)
OFF standard temperature of the switch mode power supply
RED LED:
on battery voltage <23V
off battery voltage >23V
www.pulsar.pl RSUPS54 RACK POWER
8
3.2. Optical indication of the switch operation:
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY
GREEN LED LIGHT (Power)
Indication of the switch's power
supply
OFF no power supply of the switch
ON power supply on, normal operation
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY (1÷4)
GREEN LED LIGHT (PoE)
Indication of the PoE power
supply at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant
with the IEEE802.3af standard)
ON supply at the RJ45 port
Blinking short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10MB/s or 100Mb/s
and data transmission
OFF- no connection
ON - the device is connected; 10Mb/s or 100Mb/s
Blinking data transmission
OPTICAL INDICATION AT THE UPLINK PORT
GREEN LED LIGHT
OFF- no connection
ON the device is connected; 10Mb/s or 100Mb/s
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10MB/s or 100Mb/s
and data transmission
OFF- no data transmission
ON - the device is connected: 10Mb/s or 100Mb/s
Blinking data transmission
3.3. Technical output.
The power supply is fitted with the ALARM output of collective failure (relay type). A collective failure can
be triggered by the following events:
- 230V AC mains power failure
- Failure of the switch mode power supply
- Too high temperature of the switch mode power supply (>70°C)
- Low battery voltage (<23V)
Fig. 5. Electrical diagram of the ALARM collective output of failure.
CAUTION! In Fig.5 the set of contacts shows a potential-free status of the relay, which
corresponds to power supply failure.
3.4. Acoustic indication.
A collective failure is indicated by the piezoelectric indicator, 1 beep every second. The acoustic indication
can be turned off by changing the ON / OFF position of the switch .
switch in the up position, indication ON
switch in the down position, indication OFF
www.pulsar.pl RSUPS54 RACK POWER
9
4. Operation and use.
4.1. Overload or short circuit of the PSU output.
In case of overload, the output voltage is automatically shut off, and so is the LED indicator. The restoration
of the voltage takes place immediately once the failure (overload) is over.
4.2. Battery-assisted operation.
In case of a main power outage, the device is immediately switched into a battery-assisted operation.
The PSU is equipped with the discharged battery disconnection system. During
the battery-assisted operation, reducing voltage below 19V at the battery terminals will
cause battery disconnection.
4.3. Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the
power supply network. The PSU does not require performing any specific maintenance measures. In case of fuse
replacement, use a replacement of the same parameters.
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household
waste. According to the European Union WEEE Directive, waste electrical and electronic
equipment should be disposed of separately from normal household waste
.
The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but recycled
according to the applicable law.
Pulsar
Siedlec 150, 32-744 Łapczyca, Polska
Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50
e-mail: [email protected], sales@pulsar.pl
http:// www.pulsar.pl, www.zasilacze.pl
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Pulsar RSUPS54 - v1.0 Operating instructions

Category
PoE adapters
Type
Operating instructions

Pulsar RSUPS54 - v1.0 is a 5-port switch with buffer power supply for 4 IP cameras, designed for rack mounting. It offers uninterruptible power supply, 5 10/100 Mb/s ports with 4 PoE ports supporting IEEE802.3af standard, auto-learning and aging of MAC addresses, wide range of mains supply, battery charging and maintenance control, protections against short-circuit, overload, and excessive discharging, acoustic failure indication, and optical indication for AC, DC, temperature, battery voltage, and alarm.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI