Liebherr ECBN 5066 PremiumPlusсо шарките за вратата од левата страна Owner's manual
- Category
- Fridge-freezers
- Type
- Owner's manual
ECBN 50
Operating instructions Page 16
NoFrost combined refrigerator-freezer
EN
7084 834-00
Disposal notes
The appliance contains reusable materials and should
be disposed of properly - not simply with unsorted
household refuse. Appliances which are no longer
needed must be disposed of in a professional and
appropriate way, in accordance with the current local
regulations and laws.
When disposing of the appliance, ensure that the refrigerant circuit
is not damaged to prevent uncontrolled escape of the refrigerant
it contains (data on type plate) and oil.
• Disable the appliance.
• Pull out the mains plug.
• Cut through the connection cable.
WARNING
Danger of suffocation due to packing material and plastic film!
Do not allow children to play with packaging material. Take the
packaging material to an official collection point.
Safety instructions and warnings
• To prevent injury or damage to the unit, the ap-
pliance should be unpacked and set up by two
people.
• In the event that the appliance is damaged on
delivery, contact the supplier immediately before
connecting to the mains.
• To guarantee safe operation, ensure that the ap-
pliance is set up and connected as described in
these operating instructions.
• Disconnect the appliance from the mains if any
fault occurs. Pull out the plug, switch off or remove
the fuse.
• When disconnecting the appliance, pull on the
plug, not on the cable.
• Any repairs and work on the appliance should
only be carried out by the customer service
department, as unauthor ised work could prove
highly dangerous for the user. The same applies
to changing the mains power cable.
• Do not allow naked flames or ignition sources
to enter the appliance. When transporting and
cleaning the appliance ensure that the refrigerant
circuit is not damaged. In the event of damage,
make sure that there are no ignition sources
nearby and keep the room well ventilated.
• Do not stand on the plinth, drawers or doors or
use them to support anything else.
• This appliance can be used by children of 8 years
old and over, and also by persons with restricted
physical, sensory or mental capacity or lack of
experience and knowledge, if they are supervised
or have been instructed on safe use of the appli-
ance and understand the resulting risks. Children
must not be allowed to play with the appliance.
Cleaning and user maintenance must not be
carried out by children without supervision.
• Avoid prolonged skin contact with cold surfaces or
chilled/frozen food. This could cause pain, numb-
ness and frostbite. In the case of prolonged skin
contact, protective measures should be taken,
e.g. gloves should be worn.
• Do not eat ice cream, particulary ice lollies or ice
cubes, immediately after taking them from the
freezer compartment as there is a risk of "burn-
ing" because of the very cold temperatures.
• Do not consume food which has been stored for
too long, as it could cause food poisoning.
• Do not store explosives or sprays using com-
bustible propellants such as butane, propane,
pentane etc. in the appliance. Electrical compo-
nents might cause leaking gas to ignite. You may
identify such sprays by the printed contents or a
flame symbol.
• Do not use electrical appliances inside the ap-
pliance.
• The appliance is designed for use in enclosed
areas. Do not operate the appliance outdoors or
in areas where it is exposed to splash water or
damp conditions.
• The LED light strips illuminate the interior of the
appliance. They are not suitable for lighting a
room.
A sticker to this effect may be applied to
the rear of the appliance. It refers to the
foampadded panels in the door and/or the
housing. This is only relevant for recycling.
Do not remove the sticker.
EPREL database
As from 1 March 2021, information about energy labelling and
ecodesign requirements will be available in the European product
database (EPREL). You can access the product database using
the following link: https://eprel.ec.europa.eu/. You will be asked
to enter the model identifier. You will find the model identifier on
the type plate.
16
EN
Description of the appliance
1
Operating and control elements
2
Adjustable door racks
3
Adjustable storage shelves
4
Bottle racks
5
Type plate (behind the vegetable drawer on the left-hand side)
6
Veg etable drawers
7
Water filter
8
Upper freezer drawer
9
Lower freezer drawer
bl
IceMaker (in the interior of the upper freezer drawer)
bm
Ventilation grille. In this area, the exchange of air for the refrigeration
unit takes place.
Never cover this grille or otherwise obstruct the air flow!
Freezer operating icons
Temperature setting icons
Freezer ON/OFF
SuperFrost
IceMaker ON/OFF
Refrigerator
operating icons
Refrigerator operating icons
Mute alarm (refrigerator and freezer)
SuperCool
Refrigerator ON/OFF
Temperature setting buttons
Freezer
operating icons
Control icons
Power failure LED
Dust filter LED
The dust filter in the appliance
plinth must be cleaned.
SuperCool LED
Child lock LED
Alarm LED
IceMaker ON LED
SuperFrost LED
Control
icons
Temperature and control display
Refrigerator temperature display
Freezer temperature display
Water filter has to be changed
Menu mode is activated
(for setting additional functions)
Operating and control elements
The electronic control panel has the "touch capacitance
technology". Any function can be activated by touching the
corresponding icon.
The exact contact point
is between the symbol and its label
17
Replace the filter when the waterdrop
symbol appears in the temperature
display.
Filters can be obtained from your dealer.
The drop symbol must be cancelled
after the filter has been changed. For
detailed instructions see section entitled
"Setup mode".
Water filter
Before switching on the appliance, install the water filter provided
in the interior rear wall of the refrigerator compartment.
This ensures good ice cube quality and keeps the water circuit
free of solids such as sand.
Caution!
To avoid the risk of bacteria growth, the water filter
must be changed when the waterdrop symbol appears
on the display!
It is not necessary to switch off the water supply when removing
or installing the water filter.
Water filter
location
Range of appliance use
The appliance is suitable solely for cooling food in
a domestic environment or similar. This includes,
for example, use
- in staff kitchenettes, bed and breakfast establish-
ments,
- by guests in cottages, hotels, motels and other
forms of accommodation,
- in catering and similar services in the wholesale
trade.
Use the appliance solely as is customary within a domestic envi-
ronment. All other types of use are inadmissible. The appliance
is not suitable for storing and cooling medicines, blood plasma,
laboratory preparations or similar substances and products cov-
ered by the 2007/47/EC Medical Devices Directive. Any misuse
of the appliance may result in damage to or spoilage of stored
goods. Furthermore, the appliance is not suitable for operation
in potentially explosive atmospheres.
Climate rating
The climate rating indicates the room
temperature at which the appliance may
be operated in order to achieve full refrig-
eration performance.
The climate rating is indicated on the
type plate.
The position of the type plate is shown in
the section entitled Description of the appliance.
Climate rating Room temperature
SN +10°C to +32°C
N +16°C to +32°C
ST +16°C to +38°C
T +16°C to +43°C
SN-ST +10°C to +38°C
SN-T +10°C to +43°C
Do not operate the appliance outside the
specified room temperature range.
Saving energy
- Always ensure good ventilation. Do not cover ventilation open-
ings or grille.
- Always keep fan slits clear.
- Do not place appliance in areas of direct sunlight or next to a
cooker, radiator or similar object.
- The energy consumption depends on the installation conditions,
e.g. the ambient temperature.
- Keep the time the appliance is open to a minimum.
- Store food logically.
- Ensure that all food is well packed and covered for storage. This
will prevent frost from forming.
- First cool warm food to room temperature before storing it.
- Defrost frozen food in the refrigerator.
- Empty and switch off refrigerating unit for longer vacation pe-
riods.
18
EN
Switching the appliance on and off
You are advised to clean the appliance before switching it on for
the first time (see "Cleaning").
Do not load with frozen food until the temperature shows at least
-18°C. The refrigerator and freezer compartments can be oper-
ated separately.
Switching off: keep the On/Off icons pressed for approx.
3 seconds.
Temperature display
In normal operation, the following settings
will be displayed:
- the average refrigerator temperature and
- the warmest frozen food temperature.
When starting up for the first time or when the
appliance is warm, dashes will appear until
the temperature reaches a level that can be
displayed (below 0°C in the freezer).
The display will flash:
- if you change the temperature or
- if the temperature rises by several degrees, indicating cold
loss, e.g. if you place fresh, "warm" food in the freezer or if you
remove or re-pack frozen food, the temperature may rise for a
short time due to warm air flowing into the freez er.
If F1 to F5 appears in the display, the appliance has a fault.
Consult the customer serv ice department indicating the fault
number displayed.
Switching on: touch the On/Off icons (on left
for refrigerator, on right for freezer) so that the
temperature displays light up or flash.
Setting the temperature
The appliance is pre-set for normal operation. We recommend
temperatures of +5°C in the refrigerator and -18°C in the freezer.
To reduce the temperature: touch the
Down icon; on left for refrigerator and on
right for freezer.
To increase the temperature: touch the
Up icon.
- While you are entering the temperature, the set temperature
will flash on the display.
- When you touch the temperature setting icons for the first time,
the most recent setting ("reference setting") is displayed.
- You can change the settings in increments of 1°C by briefly
touching the icons again. If the icons are held, the temperature
setting will change faster.
- Approximately 5 seconds after the last touch, the display will
automatically show the actual freezing or cooling temperature
("actual setting").
- You can change the temperatures
in the refrigerator: between 9°C and 3°C and
in the freezer: between -14°C and -28°C.
Installing the water filter
1. Remove the cover of the
filter socket.
2. Insert the filter and turn it
90° clockwise.
Removing the water filter
3. Turn the filter 90°
anticlockwise and remove.
Partition for bottom freezer drawer
If required, the partition supplied in the acces-
sories set can be inserted in the bottom drawer
on the left or right.
19
Power failure/FrostControl display
If the LED comes on on the control panel, this means that the
freezer temperature has risen too high during the last few hours
or days due to a power failure.
If you touch the ALARM icon now, the highest temperature
registered during the power failure will be displayed.
Check the quality of the food and its suitability for consumption
in case it has become too warm or even defrosted.
The highest temperature will appear for appox. 1 minute. After
that, the actual temperature in the freezer will re-appear.
The display can be switched off by touching the ALARM icon.
Audible warning signal
The appliance is equipped with an alarm function.
Audible door alarm
If an appliance door is left open for more than 60 seconds,
the audible warning signal will sound. Touch the ALARM
icon to cancel the alarm. The alarm switches back to
standby when the door is shut.
Audible/visual temperature alarm
It sounds when it is not cold enough in the freezer compartment.
The temperature display and the
LED will also flash.
The audible warning device is switched off by touching
the ALARM icon. The temperature display will continue
to flash until the cause of the alarm has been rectified.
This can be caused by:
• the freezer door being left open for a long time, allowing warm
ambient air to enter;
• a long power failure;
• a fault in the appliance.
In each case, make sure food has not thawed or perished.
SuperCool
Touching the SuperCool icon switches the refrigerator compart-
ment to maximum cooling. It is recommended particularly if you
wish to cool large quantities of food, drinks, freshly baked goods
or meals rapidly.
Switching on: Touch the SuperCool icon briefly so that
the LED
comes on. The refrigerator temperature will
drop to its lowest value.
Note: The SuperCool function uses slightly more energy. After
approximately six hours, however, the refrigerator switches back
automatically to normal energy-saving operation. If required, the
SuperCool function can be switched off sooner.
Switching off: Touch the SuperCool icon again until the LED
goes out.
Setup mode
The following functions can be activated in setup mode:
= Sabbath mode
= Child lock
= Confirm water filter change
= Ice maker vacation state
= Water quantity for ice cube tray
= Set BioFresh temperature
= Display brightness
= Door gasket heating control
=Confirm dust filter cleaning
Activating setup mode
• Touch the SuperFrost icon for five seconds.
- The SuperFrost LED comes on for 5 seconds,
- after 5 seconds
will flash in the display.
The appliance is in setup mode now.
You can select the setup mode functions by touching
the freezer compartment temperature setting icons.
Note
In setup mode the display will flash continuously.
Exiting setup mode
• Touch the freezer compartment On/Off icon
The appliance will change back to normal operation.
20
EN
= Confirm water filter change
After the water filter has been changed, the
drop symbol on the display must be reset.
Resetting the drop symbol
• Activate setup mode by touching the
SuperFrost icon for 5 seconds.
• Touch the freezer compartment Down icon
until
appears in the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon again.
- The display reads
• The drop symbol disappears.
• Exit setup mode by touching the freezer compartment On/Off
icon.
= Child lock
The child lock is designed to protect the appliance from being
switched off accidentally.
Activating the child lock
• Activate setup mode by touching
the SuperFrost icon for 5 seconds.
• Touch the freezer compartment Down icon until
appears in
the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon again.
- The
LED is lit and the child lock is activated.
• Exit setup mode by touching the freezer compartment On/Off
icon.
Deactivating the child lock
• Activate setup mode by touching
the SuperFrost icon for 5 seconds.
- The display reads
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon again.
- The
LED goes out. The child lock is deactivated.
• Exit setup mode by touching the freezer compartment On/Off
icon.
= Sabbath mode
This function complies with the religious requirements to be
observed on the Sabbath or religious holidays.
When Sabbath mode is activated, some of the functions of the
control electronics are switched off.
• The interior light remains switched off if one of the appliance
doors is opened.
• The interior fan remains in the status which is currently set (On
or Off) if an appliance door is opened.
• No door open alarm.
• No temperature alarm.
Activating the sabbath mode
• Activate setup mode by touching the SuperFrost icon for
5 seconds.
- The display reads
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon again.
- The display reads
The sabbath mode is activated.
• Exit setup mode by touching the freezer compartment On/Off
icon.
Note
The Sabbath mode is deactivated automatically after 120 hours.
Deactivating the sabbath mode
• Activate setup mode by touching the SuperFrost icon for
5 seconds.
- The display reads
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon again.
The
in the display will go out.
The sabbath mode is deactivated.
• Exit setup mode by touching the freezer compartment On/Off
icon.
21
= Lower hinge heating control
If condensed water appears in the lower
hinge area or on the base plate between
refrigerator and freezer compartment,
increase the output of the heating lo-
cated behind the base plate.
The factory setting is set to
= me-
dium output.
Changing the heating output
• Activate setup mode by touching the
SuperFrost icon for 5 seconds.
• Touch the freezer compartment Down
icon until
appears in the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the freezer compartment
Up/Down icons to select
= at slight condensation
= at heavy condensation
= heating off
• Touch the SuperFrost icon at the desired value.
• Exit setup mode by touching the freezer compartment On/Off
icon.
Note
With normal ambient conditions no condensation will appear. With
high humidity and low ambient temperature this feature helps to
prevent condensation.
= Display brightness
Adjusting the display brightness
• Activate setup mode by touching the SuperFrost icon for
5 seconds.
• Touch the freezer compartment Down icon until
appears in
the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the freezer compartment
Up/Down icons to select
0 = minimum to
5 = maximum brightness.
• Touch the SuperFrost icon at the desired value.
• Exit setup mode by touching the freezer compartment On/Off
icon.
= Ice maker vacation state
See section entitled "Ice maker".
= Water quantity for ice cube tray
If the produced ice cubes of the ice maker are too small, the
inflowing water quantity can be adjusted.
Adjusting the water quantity
• Activate setup mode by touching the SuperFrost icon for
5 seconds.
• Touch the freezer compartment Down icon until
appears in
the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the freezer compartment Up icon once only so that E 4
appears in the display.
Caution!
Do not increase for more than one step. If the adjusted value
is too high, the ice cube tray of the ice maker could overflow.
• Touch the SuperFrost icon again.
• Exit setup mode by touching the freezer compartment On/Off
icon.
Check the ice cube size within the next days. If the ice cubes are
still too small, follow the steps above again.
= Set BioFresh temperature
The temperature in the BioFresh drawers may be changed.
Setting the BioFresh temperature
• Activate setup mode by touching the SuperFrost icon for
5 seconds.
• Touch the freezer compartment Down icon until
appears in
the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the freezer compartment Up/Down icons
and set
6 - 9 to increase the temperature (warmer),
4 - 1 to reduce the temperature.
CAUTION!
For values b4 - b1, the temperature in the drawers can
drop to below 0°C. Food may freeze.
• Touch the SuperFrost icon at the desired value.
• Exit setup mode by touching the freezer compartment On/Off
icon.
22
EN
Removing the BioFresh drawer
Pull the drawer straight out,
grip at the back and lift out.
Inserting the BioFresh
drawer
Place the drawer on the pull-
out rails. The rails must be
fully extended and aligned
with the front of the drawer.
Slide the drawer in.
Repositioning the shelves
1. Hold the shelf underneath
with your hand to prevent
from tipping down back-
wards when removing.
2. Lift the shelf at the front.
3. Pull the shelf towards you
until the round cutout of
the shelf is in line with the
interior light cover.
4. Lift the shelf up and replace
in the desired position.
Removing the shelves
1. Follow the first three steps in the
chapter above.
2. Move the shelf down and stop
just over the vegetable drawer.
3. Move the front of the shelf
upwards until the shelf is in a
vertical position.
4. Turn the shelf by 90° and re-
move.
Equipment
Repositioning the door racks
Lift door rack vertically, lift out to
the front and re-insert at a different
height, following these steps in the
reverse order.
Light cover
Bottle shelf
The shelf above the BioFresh
drawers can be used for stor-
ing bottles horizontally.
Remove the glass plate and
insert it under the shelf plate.
The recesses in the shelf plate
ensure that the bottles are
stored securely.
When storing tall bottles, the
bottom door rack must be
moved further up.
By shifting the bottle holder you can
protect the bottles from falling over
when opening or closing the door.
= Confirm dust filter cleaning
Once the dust filter in the appliance plinth has been cleaned, the
dust filter LED
in the display must be cancelled.
Cancelling the dust filter symbol
• Activate setup mode by touching the SuperFrost icon for
5 seconds.
• Touch the freezer compartment Down icon until
appears in
the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon.
- The display reads
• The dust filter symbol has been cancelled.
• Exit setup mode by touching
the freezer compartment On/Off icon.
23
Arranging food
(1) butter, cheese
(2) eggs
(3) bottles
(4) frozen food, ice cubes
(5) meat, sausage products, dairy products
(6) baked goods, pre-cooked meals
(7) fruit, vegetables, salads (for high humidity setting)
meat, cold meats, dairy products (for low humidity setting)
The adjustable humidity is explained in the BioFresh com-
partment section.
Note
• Food which gives off or absorbs odours and flavours as well as
liquids should always be stored covered or in closed containers.
• High-percentage alcohols should be tightly sealed and stored
upright.
Interior light
The interior light is located at the left, right and top in the refrigerator
compartment and above each drawer in the freezer compartment.
It comes on if one of the doors or a freezer drawer is opened.
The light switches off automatically if one of the doors or a freezer
drawer has been left open for more than 15 minutes. The audible
warning signal sounds at the same time.
If one of the strip lights is not lit, it is defective.
The light intensity of the LED light corresponds to laser
class 1/1M.
Important
The light cover may only be removed by customer service
staff. If the cover is removed, do not look directly at the
light through optical lenses from close distance. This can
damage your eyes.
24
EN
Freezing
Fresh food should be frozen to the core as rapidly as possible.
Frozen food can also be given a cold boost. This is provided by
the SuperFrost facility.
The maximum amount of food
(in kg) which can be frozen in
24 hours is shown on the type
plate ("Freezing capacity").
Space for freezing and
storage
Ice maker
Ice cube bin
Freezer compartment description
Both drawers can be used for freezing of food or storage of
frozen food.
Important
In order to achieve the most efficient energy consumption pos-
sible, the container of the bottom freezer drawer must be inserted
in the appliance.
The ice cube bin in the upper drawer is intended for ice cubes only.
If you need the whole upper drawer for freezing or storage, the
ice cube bin can be removed.
Important
The ice maker will not eject the ice cubes of its tray if the bin has
been removed.
BioFresh compartment
The BioFresh compartment enables you to keep food for up to
3 times longer than in normal refrigerators.
The constant temperature of just above 0°C and the adjustable
humidity provide the ideal storage conditions for different types
of food.
The BioFresh compartment satisfies the requirements of a chill
compartment to EN 62552:2021.
Notes
• The humidity in the compartment depends on the moisture
content of the food in it, and the frequency with which the com-
partment is opened.
• The fresher the product and the higher its quality, the longer it
will keep.
• Unwrapped animal and vegetable foods should be stored
separately in the drawers. If there is not enough space for them
to be stored separately, make sure that they are wrapped. Do
not allow different types of meat to come into contact with one
another but keep them packaged separately so as to avoid
premature bacterial spoilage.
• The following products should not be stored in the BioFresh
compartment: hard cheese, potatoes, cold-sensitive vegetables
such as cucumbers, aubergines, avocadoes, semiripe tomatoes,
zucchini, all cold-sensitive tropical fruits such as pineapples,
bananas, grapefruit, melons, mangos, papayas, etc.
Dry
Small humidity symbol - slide
control to left.
This setting is suitable for dry
or wrapped food like dairy
products, meat, fish, cold
meats.
Humidity selection
Humid
High relative humidity of max.
90%, large humidity symbol -
slide control to right.
This setting is suitable for
storing unwrapped food with
a high moisture content such
as salad, vegetables and fruit.
25
Ice maker
Safety instructions and warnings
• The ice maker is designed exclusively to make ice cubes in
quantities required by a household and may only be operated
with water suitable for this purpose.
• All repairs and work on the ice maker may only be carried out
by customer service personnel or other trained personnel.
• The first three batches of ice must not be consumed or
used. This applies both to using the appliance for the first
time and also to using it after it has not been used for a
lengthy period of time.
This ensures that the water supply
is purged.
• The manufacturer cannot accept liability for damage
caused by a faulty connection to the mains water supply.
• The ice maker will only work if the combined refrigerator-freezer
is connected to the electricity supply. It will only make ice cubes
if the freezer compartment is operating.
• Ensure that the drawer is fully closed, as the ice maker can
otherwise not produce ice cubes.
Notes on freezing
• Always store identical food items together.
• Pack food which you are freezing yourself in quantities appro-
priate to your household. To ensure that the food freezes right
through, the following quantities should not be exceeded per
package: fruit, vegetables: up to 1 kg, meat: up to 2.5 kg.
• Pack frozen food in standard freezer bags or reuseable plastic,
metal or aluminium containers.
• Do not allow fresh food which is to be frozen to come into con-
tact with food already frozen. Always keep packs dry in order
to avoid them sticking together.
• Always write the date and contents on the pack and do not
exceed the stated storage time for the food.
• Do not freeze bottles and cans which contain carbonated drinks
as they might burst.
• Only take out as much food as is immediately required for
thawing. Use food which has been thawed in prepared meals
as quickly as possible.
Frozen food can be thawed in the following ways:
– in a fan oven,
– in a microwave oven,
– at room temperature,
– in the refrigerator: the cold given off by the frozen food is used
for cooling.
Bleeding the ice maker
To ensure that the ice maker works properly, the water supply
line must be bled.
• Touch the IceMaker icon
so that the IceMaker LED
comes on.
• Open the top freezer drawer.
• Press the ON/OFF button on the ice
maker housing for approx. 3 sec-
onds. The LED above the button
starts flashing.
• Press the button again briefly. The LED flashes more quickly.
• Close the freezer drawer immediately.
The water supply valve opens for 25 seconds and pumps all the
air out of the water supply system.
• Then the ice cube tray of the ice maker must be completely
emptied. See the section Activating the ice maker vacation
state.
• Finally, clean the ice cube bin.
Freezing with SuperFrost
Touch the SuperFrost icon briey so that the LED
comes on.
• For small amounts of frozen food switch on SuperFrost 6 hours
beforehand. For the maximum amount (see freezing capacity on
the type plate) you will need to switch it on 24 hours beforehand.
• Then place the fresh food inside the freezer.
- The SuperFrost function switches off automatically. Depending
on the quantity of food placed in the freezer, this will normally
be between 30 and max. 65 hours. The freezing process is now
complete, the SuperFrost LED will go out.
You should not switch on the SuperFrost func tion:
- when placing frozen food in the freezer;
- when freezing up to approx. 2 kg fresh food daily.
26
EN
Switching the ice maker on
• Touch the IceMaker icon so that the IceMaker LED
comes on.
After you start the ice maker for the first time, it may take up to
24 hours before the first ice cubes are ready.
The production capacity depends on the temperature inside the
freezer compartment. The lower the temperature, the more ice
cubes can be produced over a period of time.
The ice cubes fall out of the ice maker into the ice cube bin. When
the ice reaches a certain level in the bin, the appliance stops
producing ice automatically.
Switching the ice maker off
If you do not need any ice cubes, the ice maker can be switched
off independently of the freezer compartment.
• Touch the IceMaker icon
so that the IceMaker LED
goes out.
The ice maker can also be
switched on and off using the
ON/OFF button at the ice maker
housing.
Press the button for approxi-
mately 1 second.
Activating the ice maker vacation state
Be sure the upper freezer drawer is
completely closed and the ice cube bin
is installed correctly.
• Activate setup mode by touching the
SuperFrost icon for 5 seconds.
• Touch the freezer compartment Down
icon until
appears in the display.
• Touch the SuperFrost icon.
- The display reads
or
depending on whether the ice maker is switched
on or off.
• Touch the freezer compartment Down icon.
- The display reads
• Touch the SuperFrost icon.
- The digit
flashes.
The ice cube tray rotates down.
When the interior temperature appears in the display, the tray is in
the down position and the ice maker is switched off automatically.
Ice maker vacation state
In case of longer vacations, the ice cube tray should be emptied.
By setting the ice maker into the
vacation state, the tray will
rotate down and no water
remains in the tray.
The freezer drawer must be
left open so that the surface
of the tray dries up and no mould
or unpleasant odours can occur.
Ice cube bin
27
• Open the bottom freezer drawer and
remove the ventilation grille by pull-
ing forwards. The grille is supported
magnetically so no tool is required for
removing.
• Reset the air filter LED
.
Refer to chapter Setup Mode -
= Reset air filter LED.
• Push down the button of the air
filter, tilt to the front and remove.
Cleaning the air filter
• Clean the filter in a dishwasher or by hand with
lukewarm water and dishwasher detergent.
• Install the air filter in the reverse order.
• Install the ventilation grille.
The grille has bolts on the inside. These
bolts must be inserted into the holes of
the supports.
Cleaning
Before cleaning always switch off the appliance. Pull out
the mains plug or switch off or unscrew the fuse.
• Clean the inside, equipment and outer walls with lukewarm water
and a little detergent. Do not use abrasive or acid cleaners or
chemical solvents.
Do not use steam cleaners because of the
risk of injury and damage.
• Ensure that no cleaning water penetrates into the electrical
components or ventilation grille.
• Dry all parts well with a cloth.
• Do not damage or remove the type plate on the inside of the
appliance. It is very important for servicing purposes.
Defrosting
Refrigerator compartment
The refrigerator compartment defrosts automatically. The water
that forms on the rear wall drains into a reservoir at the back of
the appliance and evaporates automatically through the com-
pressor heat.
Freezer compartment
The NoFrost system automatically defrosts the appliance.
Any moisture arising collects on the evaporator and freezes, and
is periodically defrosted and evaporated.
28
EN
Malfunctions
You may be able to rectify the following faults by checking
the possible causes yourself:
Appliance does not function:
– Is the appliance switched on?
– Is the plug correctly fitted in the mains socket?
– Is the fuse intact?
Loud running noise:
– Is the appliance set up firmly on the floor?
– Does the appliance cause nearby items of furniture or objects
to vibrate? Please note that noises caused by the refrigerant
circuit cannot be avoided.
The temperature is not cold enough:
– Is the temperature setting correct (see "Setting the tempera-
ture")?
– Have excessive amounts of fresh food been placed in the ap-
pliance?
– Does the separately installed thermometer show the correct
reading?
– Is the ventilation system working properly?
– Is the appliance set up too close to a heat source?
If none of the above causes
apply and you cannot rectify
the fault yourself, contact the
nearest customer service de-
partment stating the type des-
ignation
1
, service number
2
and appliance number
3
as
indicated on the type plate.
The position of the type plate
is shown in the section entitled
Description of the appliance.
Shutting your appliance down
If your appliance is to be shut down for any length of time, switch
it off and disconnect the plug or switch off or unscrew the fuse.
Clean the appliance and leave the door open in order to prevent
unpleasant smells.
The appliance complies with the relevant safety regulations and
EU Directives 2014/30/EU and 2014/35/EU.
Removing the freezer drawer containers
• Open the refrigerator door.
• Pull out the freezer drawer.
• Pull the container upwards by the right and left corners (1).
• Push the container backwards (2).
• Tilt the container at an angle and remove.
• Install the container in the reverse order.
Side view of the freezer
drawer pulled out
29
Liebherr Hausgeräte Lienz GmbH
Dr.-Hans-Liebherr-Strasse 1
A-9900 Lienz
Österreich
www.liebherr.com
*708483400*
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Liebherr ECBN 5066 PremiumPlusсо шарките за вратата од левата страна Owner's manual
- Category
- Fridge-freezers
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Liebherr ECBN 6156 PremiumPlus Operating instructions
-
-
-
-
-
-
-
-
-
Other documents
-
Bosch B18IF800SP/02 Owner's manual
-
Bosch Benchmark B36IT800NP Operating instructions
-
-
Thermador T30BB810SS User guide
-
-
-
-
Bosch Benchmark B36BT830NS User manual
-
-
Thermador T36IT800NP User guide