Reloop MIXON 4 Firmware Utility Settings

Brand: Reloop

Model: MIXON 4

Type: Firmware Utility Settings

RELOOP MIXON 4

FIRMWARE UTILITY SETTINGS

This document describes all available rmware settings for MIXON 4 which

can be set on the device itself.

MODES & SETTINGS:

1. LED Check Mode

2. Firmware Version Check

3. En-/Disable LED Stand-by Sequence

4. Activate Vegas mode (LED Demo Mode)

5. Firmware Update Mode

6. Adjust LED back lit intensity

7. Adjust crossfader CUT-IN

Before launching any rmware mode, please disconnect the USB or iOS

cable, otherwise the set state may not be displayed properly.

Each rmware setting mode can be entered by holding a dedicated button

while powering on the unit. To save and exit a mode, power off the unit.

Revision v2 (11/16)

PLEASE REGULARLY CHECK FOR

UPDATES ON WWW.RELOOP.COM

RELOOP MIXON 4

FIRMWARE UTILITY SETTINGS

1. LED CHECK MODE

Turn on all LEDs:

Press and hold the PLAY-button while

powering on the unit

Each LED is now being illuminated. By

pressing any LED back lit button, the LED

can be turned on and off to check the re-

sponsiveness.

2. FIRMWARE VERSION CHECK

Before you update your rmware, you can check whether the rmware version is already installed on the unit before proceeding. In case

the displayed rmware version matches the downloaded rmware, no update is necessary.

Press and hold the CUE-button while powering on the unit

One lit LED of the left Master VU-Meter represents a step of 10.

One lit LED on the right VU-Meter represents a step of 1.

In the example on the left the current shown values represent 19.

One lit LED on the left drum pad section represents a step of 10.

One lit LED on the right drum pad section represents a step of 1.

In the example on the left the current shown values represent 13.

The current installed rmware is v1913.

Revision v2 (11/16)

PLEASE REGULARLY CHECK FOR

UPDATES ON WWW.RELOOP.COM

RELOOP MIXON 4

FIRMWARE UTILITY SETTINGS

3. EN-/DISABLE LED STANDBY SEQUENCE

The standby sequence will start by default, if there is no

operation for 10 minutes. When any control element is

moved or pressed the demo mode will stop.

Press and hold the SYNC button while powering on

the unit

As the standby sequence is ON by default, carrying out

the button combination above will disable the standby

sequence.

4. ACTIVATE VEGAS MODE (LED DEMO MODE)

The Vegas mode can be used for product presentations

or shop display.

Press and hold the SHIFT button while powering on

the unit

The Vegas LED sequence will start to run.

5. FIRMWARE UDPATE MODE

When a rmware update is available, the unit must enter

rmware update mode before proceeding with the up-

date. Otherwise the updater program cannot connect to

the unit.

Press and hold the BACK button while powering on

the unit

Both Jog Wheels will light up blue. Please refer to the in-

structions (readme.txt) found in the rmware .zip le. The

Jog Wheels will start blinking blue during the update.

When the update has been carried out successfully,

please power on the unit again.

Revision v2 (11/16)

PLEASE REGULARLY CHECK FOR

UPDATES ON WWW.RELOOP.COM

RELOOP MIXON 4

FIRMWARE UTILITY SETTINGS

6. ADJUST LED BACKLIT INTENSITY

All button LEDs have a backlight feature to ensure best performance and

visibility in dark environments.

Press and hold the BROWSE

encoder while powering on

the unit

Turning the BROWSE encoder

will adjust the LED intensity in

real time.

Press the BROWSE encoder to

save the new value.

7. ADJUST CROSSFADER CUT-IN

The crossfader CUT-IN (cut lag) can be adjusted on both sides of the crossfader in in-

crements of 0.1mm.

Press and hold the (FX-)TAP button while powering on the unit

The CUT-IN (cut lag) can be adjusted by turning the BROWSE encoder. The current value is

displayed by the VU-Meter.

One lit LED on the left VU-Meter indicates 1mm.

One lit LED on the right VU-Meter indicates 0.1 mm

In the example on the right the current set cut lag is 1.9 mm:

Press the BROWSE encoder to save the new value.

The default value is 1 mm.

Revision v2 (11/16)

PLEASE REGULARLY CHECK FOR

UPDATES ON WWW.RELOOP.COM

Reloop MIXON 4 Firmware Utility Settings

Reloop MIXON 4 Firmware Utility Settings

Reloop MIXON 4 Firmware Utility Settings

Related papers

Other documents