Indesit FH 1039 P 0 IX/HA User guide

FH 1039 P 0 IX/HA

English

Operating Instructions

OVEN

Français

Mode d’emploi

FOUR

Español

Manual de instrucciones

HORNO

Italiano

Istruzioni per l’uso

FORNO

Portuges

Instruções para a utilização

FORNO

Sommario

Istruzioni per l’uso,1

Avvertenze,2

Assistenza,5

Descrizione dell’apparecchio,7

Descrizione dell’apparecchio,8

Installazione,10

Avvio e utilizzo,12

Programmi,13

Precauzioni e consigli,17

Manutenzione e cura,17

Anomalie e rimedi,19

Contents

Operating Instructions,1

Warnings,2

Assistance,5

Description of the appliance,7

Description of the appliance,8

Installation,20

Start-up and use,22

Modes,23

Precautions and tips,27

Maintenance and care,27

Troubleshooting,29

Sommaire

Mode d’emploi,1

Avertissements,3

Assistance,5

Description de l’appareil,7

Description de l’appareil,8

Installation,30

Mise en marche et utilisation,32

Programmes,33

Précautions et conseils,37

Nettoyage et entretien,37

Anomalies et remèdes,39

Sumario

Manual de instrucciones,1

Advertencias,3

Asistencia,6

Descripción del aparato,7

Descripción del aparato,9

Instalación,40

Puesta en funcionamiento y uso,42

Programas,43

Precauciones y consejos,47

Mantenimiento y cuidados,47

Anomalías y soluciones,49

Índice

Instruções para a utilização,1

Advertências,4

Assistência,6

Descrição do aparelho,7

Descrição do aparelho,9

Instalação,50

Início e utilização,52

Programas,53

Precauções e conselhos,57

Manutenção e cuidados,57

Anomalias e soluções,59

2

Avvertenze

ATTENZIONE: Questo apparecchio e le sue parti

accessibili diventano molto caldi durante l’uso.

Bisogna fare attenzione ed evitare di toccare gli

elementi riscaldanti. Tenere lontani i bambini inferiori

agli 8 anni se non continuamente sorvegliati. Il

presente apparecchio può essere utilizzato dai

bambini a partire dagli 8 anni e da persone con

ridotte capacità siche, sensoriali o mentali oppure

con mancanza di esperienza e di conoscenza se

si trovano sotto adeguata sorveglianza oppure se

sono stati istruiti circa l’uso dell’apparecchio in modo

sicuro e se si rendono conto dei pericoli correlati. I

bambini non devono giocare con l’apparecchio. Le

operazioni di pulizia e di manutenzione non devono

essere effettuate dai bambini senza sorveglianza.

Non utilizzare prodotti abrasivi né spatole di

metallo taglienti per pulire lo sportello in vetro del

forno in quanto potrebbero grafare la supercie,

provocando, così, la frantumazione del vetro.

“Prima di attivare la funzione di pulizia automatica:

• pulire la porta del forno

• con una spugna umida togliere dall’interno del

forno i residui più consistenti. Non usare detergenti;

• estrarre tutti gli accessori e il kit guide scorrevoli

(se presente);

• non lasciare stronacci o presine sulla maniglia.”

Durante la pulizia automatica, le superci possono

diventare molto calde: tenere i bambini a distanza.

Non utilizzare mai pulitori a vapore o ad alta pressione

per la pulizia dell’apparecchio.

ATTENZIONE: Assicurarsi che l’apparecchio sia

spento prima di sostituire la lampada per evitare la

possibilità di scosse elettriche.

! Quando si inserisce la griglia assicurarsi che il

fermo sia rivolto verso l’alto e nella parte posteriore

della cavità.

Warnings

WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to

avoid touching heating elements. Children less than 8

years of age shall be kept away unless continuously

supervised. This appliance can be used by children

aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been

given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made

by children without supervision.

Do not use harsh abrasive cleaners or sharp metal

scrapers to clean the oven door glass since they can

scratch the surface, which may result in shattering of

the glass.

“Before initiating the automatic cleaning cycle:

• clean the oven door;

• remove large or coarse food residues from the

inside of the oven using a damp sponge. Do not

use detergents;

• remove all accessories and the sliding rack kit

(where present);

• do not place tea towels”

Keep children away from the appliance during the

automatic cleaning cycle as surfaces may become

very hot.

Never use steam cleaners or pressure cleaners on

the appliance.

WARNING: Ensure that the appliance is switched

off before replacing the lamp to avoid the possibility

of electric shock.

! When you place the rack inside, make sure that the

stop is directed upwards and in the back of the cavity.

Page is loading ...

5

Assistenza

Attenzione:

L’apparecchio è dotato di un sistema di diagnostica automatica che consente

di rilevare eventuali malfunzionamenti. Questi vengono comunicati dal display

tramite messaggi del tipo: “F--” seguito da numeri.

In questi casi è necessario l’intervento dell’assistenza tecnica.

Prima di contattare l’Assistenza:

• Vericare se l’anomalia può essere risolta autonomamente;

• Riavviare il programma per controllare se l’inconveniente è stato ovviato;

• In caso negativo, contattare il Servizio Assistenza Tecnico Autorizzato.

! Non ricorrere mai a tecnici non autorizzati.

Comunicare:

• Il tipo di anomalia;

• il messaggio visibile sul display TEMPERATURA

• Il modello della macchina (Mod.)

• Il numero di serie (S/N)

Queste ultime informazioni si trovano sulla targhetta caratteristiche posta

sull’apparecchio

Assistenza Attiva 7 giorni su 7

Se nasce il bisogno di assistenza o manutenzione basta chiamare il Numero

Unico Nazionale 199.199.199* per essere messi subito in contatto con il Centro

Assistenza Tecnica più vicino al luogo da cui si chiama.

È attivo 7 giorni su 7, sabato e domenica compresi, e non lascia mai inascoltata

una richiesta.

Estensione di garanzia Airbag

Airbag è il servizio esclusivo creato da Ariston che integra e prolunga nel

tempo i contenuti della garanzia standard: con una modica cifra protegge

il cliente da ogni imprevisto riguardante l’assistenza e la manutenzione

dell’elettrodomestico. Per i 5 anni successivi alla data di acquisto il cliente

che aderisce al programma Airbag avrà diritto gratuitamente a:

• l’intervento entro 48 ore dalla chiamata;

• il contributo per spese di trasferta del Tecnico (diritto di chiamata);

• la manodopera;

• le parti di ricambio originali;

• il trasporto dell’elettrodomestico non riparabile in loco.

Inoltre, qualora l’elettrodomestico non sia riparabile la garanzia prevede

la sostituzione a prezzo agevolato in funzione dell’anzianità del prodotto.

* Al costo di 14,25 centesimi di Euro al minuto (iva inclusa) dal Lun. al Ven.

dalle 08:00 alle 18:30, il Sab. dalle 08:00 alle 13:00 e di 5,58 centesimi di

Euro al minuto (iva inclusa) dal Lun. al Ven. dalle 18:30 alle 08:00, il Sab. dalle

13:00 alle 08:00 e i giorni festivi, per chi chiama dal telefono sso.

Per chi chiama da radiomobile le tariffe sono legate al piano tariffario

dell’operatore telefonico utilizzato.

Le suddette tariffe potrebbero essere soggette a variazione da parte

dell’operatore telefonico; per maggiori informazioni consultare il sito www.

indesit.com.

Assistance

Warning:

The appliance is tted with an automatic diagnostic system which detects any

malfunctions. Malfunctions are signalled through messages of the following

type: “F—” followed by numbers.

Call for technical assistance in the event of a malfunction.

Before calling for Assistance:

• Check whether you can x the problem yourself.

• Restart the programme to check whether the malfunction has

disappeared.

• If it has not, contact the Authorised Technical Assistance Service.

! Never use the services of an unauthorised technician.

Please have the following information to hand:

• The type of problem encountered.

• The message shown on the TEMPERATURE display.

• The appliance model (Mod.).

• The serial number (S/N).

The latter two pieces of information can be found on the data plate located

on the appliance.

Assistance

Attention :

L’appareil dispose d’un système d’autotest qui permet de détecter toute

anomalie de fonctionnement. Ces anomalies sont afchées sous la forme:

«F—» suivi de chiffres.

Contacter alors un service d’assistance technique.

Avant d’appeler le service de dépannage :

• Vérier s’il est possible de résoudre le problème soi-même ;

• Redémarrer le programme pour contrôler si le problème a été résolu;

• Si ce n’est pas le cas, contacter le service d’Assistance technique agréé.

! Ne jamais faire appel à des techniciens non agréés.

Indiquer :

• le type d’anomalie;

• le code erreur afché sur l’écran TEMPERATURE

• le modèle de l’appareil (Mod.);

• son numéro de série (S/N).

Ces informations gurent sur la plaque signalétique apposée sur l’appareil

Page is loading ...

7

Descrizione dell’apparecchio

Vista d’insieme

1 POSIZIONE 1

2 POSIZIONE 2

3 POSIZIONE 3

4 POSIZIONE 4

5 POSIZIONE 5

6 GUIDE di scorrimento dei ripiani

7 Ripiano LECCARDA

8 Ripiano GRIGLIA

9 Pannello di controllo

Description of the appliance

Overall view

1 POSITION 1

2 POSITION 2

3 POSITION 3

4 POSITION 4

5 POSITION 5

6 GUIDES for the sliding racks

7 DRIPPING PAN

8 GRILL

9 Control panel

Description de l’appareil

Vue d’ensemble

1 NIVEAU 1

2 NIVEAU 2

3 NIVEAU 3

4 NIVEAU 4

5 NIVEAU 5

6 GLISSIERES de coulissement

7 Support LECHEFRITE

8 Support GRILLE

9 Tableau de bord

Descripción del aparato

Vista en conjunto

1 POSICIÓN 1

2 POSICIÓN 2

3 POSICIÓN 3

4 POSICIÓN 4

5 POSICIÓN 5

6 GUÍAS de deslizamiento de las bandejas

7 Bandeja GRASERA

8 Bandeja PARRILLA

9 Panel de control

Descrição do aparelho

Vista de conjunto

1 POSIÇÃO 1

2 POSIÇÃO 2

3 POSIÇÃO 3

4 POSIÇÃO 4

5 POSIÇÃO 5

6 GUIAS de escorrimento das prateleiras

7 Prateleira BANDEJA PINGADEIRA

8 Prateleira GRADE

9 Painel de comandos

7

8

9 6

1

2

3

4

5

8

Descrizione dell’apparecchio

Pannello di controllo

1. Icone PROGRAMMI MANUALI

2. Selezione FAST CLEAN

3. Display TEMPERATURA

4. Icona TEMPERATURA

5. Icona DURATA

6. Display TEMPI

7. Icona FINE COTTURA

8. Icona BLOCCO PORTA/COMANDI

9. AVVIO/ARRESTO

10. Icona LUCE

11. Icona OROLOGIO

12. Icona CONTAMINUTI

13. Icone REGOLAZIONE TEMPI/TEMPERATURA

14. Icone PRERISCALDAMENTO/CALORE RESIDUO

15. Indicatore PORTA BLOCCATA

16. Icone PROGRAMMI AUTOMATICI/ECO

17. ACCENSIONE PANNELLO

Description of the appliance

Control panel

1. MANUAL COOKING MODE Icons

2. FAST CLEAN selector

3. TEMPERATURE display

4. TEMPERATURE icon

5. DURATION icon

6. TIME display

7. END OF COOKING Icon

8. DOOR / CONTROL PANEL LOCK icon

9. START / STOP

10. LIGHT icon

11. CLOCK icon

12. MINUTE MINDER Icon

13. TIME / TEMPERATURE ADJUSTMENT Icons

14. PREHEATING / RESIDUAL HEAT icons

15. DOOR LOCK indicator

16. AUTOMATIC/ECO COOKING MODE icons

17. CONTROL PANEL POWER BUTTON

Description de l’appareil

Tableau de bord

1. Icônes PROGRAMMES MANUELS

2. Sélection FAST CLEAN

3. Afcheur TEMPERATURE

4. Icône TEMPÉRATURE

5. Icône DURÉE

6. Afcheur TEMPS

7. Icône FIN CUISSON

8. Icône VERROUILLAGE PORTE / COMMANDES

9. DÉPART / ARRÊT

10. Icône ECLAIRAGE

11. Icône HORLOGE

12. Icône MINUTEUR

13. Icônes RÉGLAGE TEMPS / TEMPÉRATURE

14. Icône PRÉCHAUFFAGE / CHALEUR RÉSIDUELLE

15. Voyant PORTE VERROUILLÉE

16. Icônes PROGRAMMES AUTOMATIQUES / ECO

17. ALLUMAGE PANNEAU

10

11

12

13

15

1

43

7

6

5

8

9

16

2

14

17

Page is loading ...

20

GB

Installation

! Please keep this instruction booklet in a safe place for future reference. If

the appliance is sold, given away or moved, please make sure the booklet is

also passed on to the new owners so that they may benet from the advice

contained within it.

! Please read this instruction manual carefully: it contains important information

concerning the safe operation, installation and maintenance of the appliance.

Positioning

! Do not let children play with the packaging material; it should be disposed

of in accordance with local separated waste collection standards (see

Precautions and tips).

! The appliance must be installed by a qualied professional in accordance

with the instructions provided. Incorrect installation may damage property or

cause harm to people or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance operates properly:

• The panels adjacent to the oven must be made of heat-resistant material.

• Cabinets with a veneer exterior must be assembled with glues which can

withstand temperatures of up to 100°C.

• To install the oven under the counter (see diagram) or in a kitchen unit,

the cabinet must have the following dimensions:

595 mm.

25 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

560 mm.

547 mm. min.

! The appliance must not come into contact with electrical parts once it has

been installed. The indications for consumption given on the data plate have

been calculated for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be

removed. It is advisable to install the oven so that it rests on two strips of

wood, or on a completely at surface with an opening of at least 45 x 560

mm (see diagrams).

560 mm.

45 mm.

Centring and xing

Secure the appliance to the cabinet by opening the oven door and putting 4

screws into the 4 holes on the outer frame.

! All parts which ensure the safe operation of the appliance must not be

removable without the aid of a tool.

Electrical connection

Ovens equipped with a three-pole power supply cable are designed to operate

with alternating current at the voltage and frequency indicated on the data

plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal board by

inserting a screwdriver into the side

tabs of the cover. Use the screwdriver

as a lever by pushing it down to open

the cover (see diagram).

2. Install the power supply cable by

loosening the cable clamp screw and

the three wire contact screws

L-N- .

Connect the wires to the

corresponding terminals: the Blue

wire to the terminal marked (N), the

Brown wire to the terminal marked

(L) and the Yellow/Green wire to the

terminal marked

(see diagram).

3. Secure the cable by fastening the

clamp screw.

4. Close the cover of the terminal

board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data

plate (see table).

The appliance must be directly connected to the mains using an omnipolar

switch with a minimum contact opening of 3 mm installed between the

appliance and the mains. The switch must be suitable for the charge indicated

and must comply with current electrical regulations (the earthing wire must not

be interrupted by the switch). The supply cable must be positioned so that it

does not come into contact with temperatures higher than 50°C at any point

(the back panel of the oven, for example).

L

N

L

GB

21

! The installer must ensure that the correct electrical connection has been

performed and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance, which is

indicated on the data plate.

• The voltage is in the range between the values indicated on the data plate.

• The socket is compatible with the plug of the appliance. If the socket is

incompatible with the plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the

electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised technicians

only (see Assistance).

! The manufacturer declines any liability should these safety measures

not be observed.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 32,4 cm

depth 41.5 cm

Volume*

59 l

Dimensions**

width 45.5 cm

height 32,4 cm

depth 41.5 cm

Volume**

62 l

Electrical

connections

voltage: 220-240V~ 50/60 Hz or 50Hz

maximum power absorbed 2800 W

(see data plate)

* Only for models with drawn rails.

** Only for models with wire rails.

EU Directive no 65/2014

supplementing Directive 2010/30/EU.

EU Regulation no 66/2014

implementing Directive 2009/125/EC.

Standard EN 60350-1

Standard EN 50564

This appliance conforms to the

following European Economic

Community directives:

- 2006/95/EC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 2004/108/EC of 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments;

- 93/68/EEC of 22/07/93 and

subsequent amendments.

- 2002/96/EU and subsequent

amendments.

- 1275/2008 standby/off mode.

ENERGY LABEL

and

ECODESIGN

Declared energy consumption

for Forced convection Class –

heating mode: ECO.

22

GB

Start-up and use

WARNING! The oven is provided

with a stop system to extract the

racks and prevent them from coming

out of the oven (1).As shown in the

drawing, to extract them completely,

simply lift the racks, holding them on

the front part, and pull (2).

! The rst time you use your appliance, heat the empty oven with its door closed

at its maximum temperature for at least half an hour. Make sure that the room

is well ventilated before switching the oven off and opening the oven door. The

appliance may emit a slightly unpleasant odour caused by protective substances

used during the manufacturing process burning away.

! To make the setting process easier, press and hold the “

” and “ ” buttons

to scroll through the numbers on the display rapidly.

! Each setting will automatically be stored in the appliance memory after 10

seconds.

! The touch controls cannot be activated if the user is wearing gloves.

! In order to optimise the cooking performance, when starting the selected

function, product settings will be applied that could cause a delayed start of

the fan and heating elements.

Control panel/door lock

! The door and control panel can be locked while the oven is off, once cooking

has started or nished and during programming.

To lock the door and the oven controls, press and hold the

icon for at

least 2 seconds. A buzzer sounds and the display shows the key symbol

“n—O”. The

and icons, when lit, indicate lock function activation.

To deactivate the lock, press and hold the icon again for at least 2

seconds.

! When cleaning the appliance, the door lock may be closed accidentally

(there is an exposed spring). If this happens, reopen it by turning the door

lock upwards (see gure).

KO OK

Setting the clock

! The clock can only be set when the oven is switched off. If the oven is in

standby mode, pressing the

button once will display the current time

setting. Press it again to set the time.

After connection to the power supply network or after a blackout, the

button and the digits on the TIME display will ash for 10 seconds.

To set the clock:

1. Press the

button.

2. Adjust the hour gure using the and buttons.

3. Once you have reached the correct hour value, press the

button.

4. Repeat the above process to set the minutes.

If a blackout occurs, it will be necessary to reset the clock. If the

icon

ashes on the display, this indicates that the clock has not been set correctly.

Setting the minute minder

! The minute minder may be set regardless of whether the oven is switched

on or off. It does not switch the oven on or off.

When the set time has elapsed, the timer emits a buzzer that will automatically

stop after 30 seconds or when any active button on the control panel is

pressed.

To adjust the timer proceed as follows:

1. Press button

.

2. Set the desired time using buttons “

” and “ ”.

3. Once you have reached the desired value, press the

button again.

The lit

symbol will remind you that the minute minder is on.

To cancel the minute minder, press the

button and use the “ ” and “

” buttons to set the time to 00:00. Press button again.

The

icon will switch off to indicate that the minute minder has been

disabled.

Starting the oven

1. Switch the control panel on by pressing the button. The appliance

buzzer sounds three times (ascending) and all buttons light up in sequence.

2. Press the button corresponding to the desired cooking mode. The

TEMPERATURE display shows:

- the temperature associated with the mode, if programming manually;

- “Auto”, if programming is automatic.

The TIME display shows:

- the current time, if programming manually;

- the duration, if programming is automatic.

3. Press the

button to begin cooking.

4. The oven will begin its preheating phase, the preheating indicators will light

up as the temperature rises.

5. When the preheating process has nished, a buzzer sounds and all the

preheating indicator lights show that this stage has been completed: the food

can then be placed in the oven.

6. During cooking it is always possible to:

- change the temperature by pressing the

button, followed by the “ ”

and “

” buttons (manual modes only);

- set the duration of a cooking mode (see Cooking Modes);

- press the

button to stop cooking. In this case the appliance stores the

temperature modied previously in its memory (manual modes only);

- switch off the oven by pressing the

button for 3 seconds.

7. If a blackout occurs while the oven is already in operation, an automatic

system within the appliance will reactivate the cooking mode from the point at

which it was interrupted, provided that the temperature has not dropped below

a certain level. Programmed cooking modes which have not yet started will

not be restored and must be reprogrammed (for example: a cooking mode

has been programmed to start at 20:30. At 19:30 a blackout occurs. When the

power supply is restored, the mode will have to be reprogrammed).

GB

23

! There is no preheating stage for the GRILL mode.

! Never put objects directly on the bottom of the oven; this will prevent the

enamel coating from being damaged.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the oven, a cooling fan

blows a stream of air between the control panel and the oven door, as well

as towards the bottom of the oven door.

At the beginning of the FAST CLEAN mode, the cooling fan operates at low

speed.

! Once cooking has been completed, the cooling fan continues to operate

until the oven has cooled down sufciently.

Oven light

The light comes on when the oven door is opened or when a cooking mode

starts. The

button can be used to switch on the light at any time.

Residual heat indicators

The appliance is tted with a residual heat indicator. When the oven is off,

the “residual heat” bar on the display lights up to indicate high temperatures

inside the oven cavity. The individual segments of the bar switch off one by

one as the temperature inside the oven falls.

Demo mode

The oven can operate in the DEMO mode: all heating elements are

deactivated, and the controls remain operative.To activate DEMO mode,

press and release button

, then buttons “ ” and “ ” simultaneously for

6 seconds, and then press and release button

.A buzzer sounds and the

TEMPERATURE display shows “dEon”. To deactivate DEMO mode, when

the oven is off press and hold button

and button “ ” simultaneously

for 3 seconds. A buzzer sounds and the “dEoF” message disappears from

the display.

Restoring the factory settings

The oven factory settings can be restored to reset all selections made by

the user (clock and customised durations). To carry out a reset, switch off

the oven, then press and hold the button corresponding to the rst manual

cooking mode (top left) and the

button simultaneously for 6 seconds.

Once the restore procedure is complete, a buzzer will sound. The rst time

the

button is pressed, the oven will behave as if it is being switched

on for the rst time.

Standby

This product complies with the requirements of the latest European Directive

on the limitation of power consumption of the standby mode. If no buttons

are pressed for 30 minutes and the control panel/door lock has not been

activated, the appliance automatically reverts to standby mode. Standby mode

is indicated by the high luminosity “Clock button” light. As soon as interaction

with the machine resumes, the system’s operating mode is restored.

Modes

! Every time the oven is switched on, it suggests the rst manual cooking mode.

Manual cooking modes

! All cooking modes have a default cooking temperature which may be

adjusted manually to a value between 30°C and 250°C as desired (300°C

for GRILL mode). Any temperature adjustments will be stored in the

appliance memory and suggested again the next time this mode is used.

If the selected temperature is lower than the temperature inside the oven,

the text “Hot” appears on the TEMPERATURE display. However, it will still

be possible to start cooking.

MULTILEVEL mode

All heating elements and the fan are activated. Since the heat remains constant

throughout the oven, the air cooks and browns food in a uniform manner. A

maximum of two racks may be used at the same time.

BARBECUE mode

The top heating element and the rotisserie spit (where present) are activated.

The high and direct temperature of the grill is recommended for food which

requires a high surface temperature. Always cook in this mode with the oven

door closed (see “Practical cooking advice”).

FAN GRILLING mode

The top heating element and the rotisserie spit (where present) are activated

and the fan begins to operate. During part of the cycle the circular heating

element is also activated. This combination of features increases the

effectiveness of the unidirectional thermal radiation provided by the heating

elements through the forced circulation of the air throughout the oven.

This helps prevent food from burning on the surface and allows the heat to

penetrate right into the food. Always cook in this mode with the oven door

closed (see “Practical cooking advice”).

LOW TEMPERATURE modes

This type of cooking can be used for proving, defrosting, preparing yoghurt,

heating dishes at the required speed and slow cooking at low temperatures.

The temperature options are: 40, 65 and 90°C.

PIZZA modes

The top and circular heating elements switch on and the fan begins to operate.

This combination heats the oven rapidly. If you use more than one rack at a

time, switch the position of the dishes halfway through the cooking process.

BAKING mode

The rear heating element and the fan are switched on, thus guaranteeing the

distribution of heat in a delicate and uniform manner throughout the entire oven.

This mode is ideal for baking temperature sensitive foods (such as cakes,

which need to rise).

24

GB

ECO mode

The back heating element is turned on and the fan starts working, ensuring

a smooth and uniform heat level inside the oven.

This programme is indicated for slow cooking of any type of food with

temperatures which can be set up to a maximum of 200°C; the programme

is also suitable for heating food and to complete the cooking process.

The programme is particularly suitable for the slow cooking of meat and sh,

as it allows you to have softer meat and save energy at the same time. For

a better energy effectiveness, when the product is turned on, the light stays

on only for 30 seconds; in order to turn the light back on, please press the

button

Rotisserie spit*

To operate the rotisserie function

(see diagram) proceed as follows:

1. Place the dripping pan in position

1.

2. Place the rotisserie support in

position 3 and insert the spit in the

hole provided on the back panel of

the oven.

3. Start the rotisserie function by

selecting the

or modes;

! When

mode is on, the rotisserie will stop if the door is opened.

Automatic cooking modes

! The temperature and cooking duration are pre-set values, guaranteeing

a perfect result every time - automatically. These values are set using the

C.O.P.® (Programmed Optimal Cooking) system. The cooking cycle stops

automatically and the oven indicates when the dish is cooked. You may start

cooking whether the oven has been preheated or not.

The cooking duration can be customised according to personal taste by

modifying the relevant value - before cooking begins - by ±5/20 minutes

depending on the selected programme. The duration can however be

modied even once cooking has begun. If the value is modied before the

programme begins, it is stored in the memory and suggested again by the

appliance when the programme is next used. If the temperature inside the

oven is higher than the suggested value for the selected mode, the text “Hot”

appears on the TEMPERATURE display and it will not be possible to begin

cooking; wait for the oven to cool.

! When the cooking stage has been reached, the oven buzzer sounds.

! Do not open the oven door as this will disrupt the cooking time and

temperature.

BEEF mode

Use this function to cook beef, pork and lamb. Place the food inside the oven

while it is still cold. The dish may also be placed in a preheated oven.

FISH FILLETS mode

This function is ideal for cooking small-medium llets. Place the food inside

the oven while it is still cold.

BREAD mode

Use this function to bake bread. To obtain the best results, we recommend

that you carefully observe the instructions below:

• follow the recipe;

• do not exceed the maximum weight of the dripping pan;

• remember to pour 50 g (0,5 dl) of cold water into the baking tray in

position 5.

• The dough must be left to rise at room temperature for 1 – 1 ½ hours

(depending on the room temperature) or until the dough has doubled in

size.

Recipe for BREAD:

1 Dripping pan holding 1000 g Max, lower level

2 Dripping pans each holding 1000 g Max, medium and lower levels

Recipe for 1000 g of dough: 600 g our, 360 g water, 11g salt, 25 g fresh yeast

(or 2 sachets of powder yeast)

Method:

• Mix the our and salt in a large bowl.

• Dilute the yeast in lukewarm water (approximately 35 degrees).

• Make a small well in the mound of our.

• Pour in the water and yeast mixture.

• Knead the dough by stretching and folding it over itself with the palm of

your hand for 10 minutes until it has a uniform consistency and is not too

sticky.

• Form the dough into a ball shape, place it in a large bowl and cover it with

transparent plastic wrap to prevent the surface of the dough from drying

out. Select the manual LOW TEMPERATURE function on the oven and

set the temperature to 40°C. Place the bowl inside and leave the dough

to rise for approximately 1 hour (the dough should double in volume).

• Cut the dough into equal sized loaves.

• Place them in the dripping pan, on a sheet of baking paper.

• Dust the loaves with our.

• Make incisions on the loaves.

• Place the food inside the oven while it is still cold.

• Start the

BREAD cooking mode.

• Once baked, leave the loaves on one of the grill racks until they have

cooled completely.

BAKED CAKES mode

This function is ideal for cooking desserts which are made using natural yeast,

baking powder and desserts which contain no yeast. Place the dish in the

oven while it is still cold. The dish may also be placed in a preheated oven.

TARTS mode

This function is ideal for all tart recipes (which normally need to be heated

well from underneath). Place the food inside the oven while it is still cold.

The dish may also be placed in a preheated oven.

Programming cooking

! A cooking mode must be selected before programming can take place.

! Once a cooking mode has been selected, the

button is activated; it will

then be possible to program a duration. The button is only activated after

a duration has been set; it will then be possible to program a delayed start.

Programming the duration

1. Press the

button; the button and the numbers on the TIME

display will ash.

2. Set the duration by pressing buttons “ ” and “ ”.

3. Once you have reached the desired duration, press the

button again.

* Only available in certain models.

GB

25

4. Press the button to begin cooking.

5. When cooking has nished, “END” appears on the TEMPERATURE display

and a buzzer sounds.

• For example: it is 9:00 a.m. and a duration of 1 hour and 15 minutes is

programmed. The programme will stop automatically at 10:15 a.m.

Programming delayed cooking

! A cooking duration must be set before the cooking end time can be scheduled.

! For the delayed programming to work properly, the clock should be set to

the correct time.

1. Press the

button and repeat steps 1 to 3 as described for the duration

setting.

2. Then press the button and set the end time using the “ ” and “

” buttons.

3. Once you have reached the desired end time, press the button again.

4. Press the

button to activate the programmed mode.

The

and buttons will ash alternately to indicate that programming

has taken place; in the time before cooking starts, the TIME display will show

the duration and the cooking end time alternately.

5. Once cooking has nished, “END” appears on the TEMPERATURE display

and a buzzer sounds.

• For example: it is 9:00 a.m. and a time of 1 hour and 15 minutes is

programmed, while the end time is set to 12:30. The programme will

start automatically at 11:15 a.m.

To cancel programming press the

button.

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-assisted cooking. This is

because excessive direct heat can burn temperature sensitive foods.

! In the GRILL and FAN GRILLING cooking modes, particularly when using

the rotisserie spit, place the dripping pan in position 1 to collect cooking

residues (fat and/or grease).

MULTILEVEL

• Use positions 2 and 4, placing the food which requires more heat on 2.

• Place the dripping pan on the bottom and the rack on top.

GRILL

• Place the rack in position 3 or 4. Position the food in the centre of the rack.

• We recommend that the temperature is set to its maximum level. The top

heating element is regulated by a thermostat and may not always operate

constantly.

PIZZA

• Use a lightweight aluminium pizza pan. Place it on the rack provided.

For a crispy crust, do not use the dripping pan as this extends the total

cooking duration and prevents the crust from forming.

• If the pizza has a lot of toppings, we recommend adding the mozzarella

cheese to the top of the pizza halfway through the cooking process.

26

GB

Modes FoodsWeight

(in kg)

Preheating

Manual

Standard

guide

rails

Sliding

guide

rails

Multilevel*

1+1

1

2 and 4

1 and 2/3

2

1 or 2

2

2 and 4

1 and 3

1

1 and 3

yes

20-25

30-35

20-30

65-75

45-50

30-35

35-40

20-25

10-20

20-25

25-35

Grill*

1

0,7

0,5

0,8

0,7

n° 4 or 5

n° 4 or 6

1

4

3 or 4

4

-

3

2 or 3

3

-

no

300

10-20

10-15

15-20

10-20

10-12

3-5

70-80

Fan grilling*

1,5

1

1,5

1

2

-

2

-

2

no

210

200

210

55-60

30-35

70-80

60-70

60-75

70-80

40-45

Proving / Defrosting

White meringues

Meat / Fish

-

2

1

no

40

65

90

-

8-12 ore

90-180

Pizza*

Pi zza

Focaccia bread

0,5

2

1

yes

15-20

20-25

Baking*

0,5

1

0,7

0,6

0,7

0,8

0,5

2 or 3

2 and 4

2 or 3

1 and 3

2

1 and 3

2

1 or 2

1 and 3

1 or 2

1 and 2

1

1 and 2

1

yes

180

180-190

160-170

180-190

180

200

90

210

25-35

40-50

45-55

20-25

35-40

20-30

20-25

30-35

180

20-25

Automatic**

Beef

Roast dishes12 or 32 no

Fish fillets

Cod

Perch

Trout

0,4-0,5

2 or 3

2

no

Bread***

Bread (see recipe)

11 or 21 no

Baked cakes

12 or 32 no

Tarts

0,52 or 32 no

Cooking advice table

Low

temperature*

Rack position Recommended

Temperature

(°C)

Cooking

duration

(minutes)

1 and 3 and 5

1 and 2 and 4

50 0,5

210-220

180

160-170

200-210

190-200

180

180-190

190

180

210

190-200

210-220

190-200

! ECO programme: This programme can be used for slow cooking of any type of food with temperatures which can be set up to a maximum of 200°C;

the programme is also suitable for heating food and to complete the cooking process.

GB

27

Precautions and tips

! This appliance has been designed and manufactured in compliance with

international safety standards. The following warnings are provided for safety

reasons and must be read carefully.

General safety

• The appliance was designed for domestic use inside the home and is

not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in covered areas. It is

extremely dangerous to leave the appliance exposed to rain and storms.

• When moving or positioning the appliance, always use the handles

provided on the sides of the oven.

• Do not touch the appliance while barefoot or with wet or damp hands and

feet.

• The appliance must be used by adults only for the preparation of

food, in accordance with the instructions provided in this booklet.

Any other use of the appliance (e.g. for heating the room) constitutes

improper use and is dangerous. The manufacturer may not be held

responsible for any damage caused as a result of improper, incorrect

and unreasonable use of the appliance.

• Do not touch the heating elements or certain parts of the oven door

when the appliance is in use; these parts become extremely hot.

Keep children well away from the appliance.

• Make sure that the power supply cables of other electrical appliances do

not come into contact with the hot parts of the oven.

• The ventilation and heat dispersal openings must never be obstructed.

• Always grip the oven door handle in the centre: the ends may be hot.

• Always use oven gloves when placing cookware in the oven or when

removing it.

• Do not use aluminium foil to line the bottom of the oven.

• Do not place ammable materials in the oven: if the appliance is switched

on accidentally, the materials could catch re.

• When unplugging the appliance, always pull the plug from the mains

socket; do not pull on the cable.

• Do not perform any cleaning or maintenance work without having

disconnected the appliance from the electricity mains.

• If the event of malfunctions, under no circumstances should you attempt

to perform the repairs yourself. Contact an authorised Service Centre (see

Assistance).

• Do not rest objects on the open oven door.

• Do not let children play with the appliance.

• The appliance should not be operated by people (including children)

with reduced physical, sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary instructions

relating to the operation of the appliance.

• The appliance is not intended to be operated by means of an external

timer or separate remote-control system.

Disposal

• When disposing of packaging material: observe local legislation so that

the packaging may be reused.

• The European Directive 2012/19/EU on Waste Electrical and

Electronic Equipment (WEEE), requires that old household electrical

appliances must not be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected separately in order

to optimise the recovery and recycling of the materials they contain

and reduce the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product reminds you of your

obligation, that when you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or retailer for information

concerning the correct disposal of their old appliance.

Respecting and conserving the environment

• Whenever possible, avoid pre-heating the oven and always try to ll it.

Open the oven door as little as possible because heat is lost every time it

is opened. To save a substantial amount of energy, simply switch off the

oven 5 to 10 minutes before the end of your planned cooking time and

use the heat the oven continues to generate.

• Automatic programmes are based on standard food product.

• Keep gaskets clean and tidy to prevent any door energy losses

• If you have a timed tariff electricity contract, the “delay cooking” option

will make it easier to save money by moving operation to cheaper time

periods.

! This product complies with the requirements of the latest European Directive

on the limitation of power consumption of the standby mode.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before carrying out

any work on it.

Cleaning the appliance

• Slight differences in colour on the front of the oven are due to the different

materials used, i.e. glass, plastic or metal.

• Any shady areas resembling grooves on the oven door glass are caused

by reections from the oven light.

• The enamel is branded at very high temperatures. This process may cause

colour variations. This is normal and will not affect appliance operation in

any way. The thin edges of the sheet metal cannot be entirely enamelled

and may therefore appear to be unnished. This will not affect the rust

protection.

• The stainless steel or enamel-coated external parts and the rubber seals

may be cleaned using a sponge that has been soaked in lukewarm water

and neutral soap. Use specialised products for the removal of stubborn

stains. After cleaning, rinse and dry thoroughly. Do not use abrasive

powders or corrosive substances.

• The inside of the oven should ideally be cleaned after each use, while it is

still lukewarm. Use hot water and detergent, then rinse well and dry with

a soft cloth. Do not use abrasive products.

• All accessories - with the exception of the sliding racks - can be washed

like everyday crockery, and are even dishwasher safe.

• We recommend that detergents are not sprayed directly onto the control

panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge and a non-abrasive

cleaning product, then dry thoroughly with a soft cloth. Do not use rough

abrasive material or sharp metal scrapers as these could scratch the surface

and cause the glass to crack.

For more thorough cleaning purposes, the oven door may be removed:

1. Open the oven door fully (see diagram).

2. Use a screwdriver to lift up and turn the small levers F located on the two

hinges (see diagram).

28

GB

F

3. Grip the door on the two outer sides and

close it approximately half way. Pull the

door towards you, lifting it out of its slot (see

diagram). To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals are damaged,

please contact your nearest Service Centre (see Assistance). We recommend

that the oven is not used until the seals have been replaced.

Replacing the light bulb

To replace the oven light bulb:

1. Remove the glass cover of the

lamp-holder.

2. Remove the light bulb and replace

it with a similar one: halogen lamp

voltage 230 V, wattage 25 W, cap

G 9.

3. Replace the glass cover (see

diagram).

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Sliding rack kit assembly

To assemble the sliding racks:

1. Remove the two frames, lifting

them away from the spacers A (see

gure).

2. Choose which shelf to use with the

sliding rack. Paying attention to the

direction in which the sliding rack is

to be extracted, position joint B and

then joint C on the frame.

Glass cover

Lamp

Holder

compartment

A

B

C

Left

guide rail

Right guide

rail

Direction

of extraction

3. Secure the two frames with the

guide rails using the holes provided

on the oven walls (see diagram).

The holes for the left frame are

situated at the top, while the holes

for the right frame are at the bottom.

4. Finally, fit the frames on the

spacers A.

! Do not place the sliding racks in position 5.

Automatic cleaning with the FAST CLEAN function

With the FAST CLEAN mode, the internal temperature of the oven reaches

500°C. The pyrolytic cycle is activated, burning away food and grime

residues. Dirt is literally incinerated.

Keep children away from the appliance during the automatic cleaning cycle

as surfaces may become very hot. Particles may ignite inside the oven as a

result of the combustion process. There is no cause for concern: this process

is both normal and hazard-free.

Before initiating the FAST CLEAN mode:

• clean the oven door;

• remove large or coarse food residues from the inside of the oven using a

damp sponge. Do not use detergents;

• remove all accessories and the sliding rack kit (where present);

• do not place tea towels or pot holders over the oven handle.

! If the oven is too hot, the pyrolytic cycle may not start. Wait for the oven to

cool down.

! The programme may only be started once the oven door has been closed.

To activate the Fast Clean programme:

1. Switch the control panel on by pressing the

button.

2. Press the

button; the TIME display will show the default duration of

1:30 h (normal cycle), while he TEMPERATURE display will show “Piro” and

“nor” alternately;

3. The desired cleaning level can be selected by pressing the

button, then:

- pressing “ ” to switch to the intensive cycle: the duration is 2 h and the

TEMPERATURE display shows the text “Piro” and “int” alternately;

- pressing “ ” to switch to the economy cycle: the duration is 1 h and the

TEMPERATURE display shows the text “Piro” and “eco” alternately.

Safety devices

• the door locks automatically as soon as the temperature reaches a high

value; the

icon lights up on the display;

• pressing the

button cancels the cleaning cycle t any time;

• if a malfunction occurs, the heating elements will be switched off;

• once the oven door has been locked, you cannot change the duration and

end time settings.

D

GB

29

Programming delayed automatic cleaning

! Programming is possible only after selecting the FAST CLEAN mode.

1. Press the

button and set the end time using

the “

” and “ ” buttons.

2. Once you have reached the desired end time, press the button again.

3. Press the

button to activate the programmed mode.

4. When the selected time has elapsed, “END” appears on the TEMPERATURE

display and a buzzer sounds.

• For example: it is 9:00 a.m. and the Economy (ECO) FAST CLEAN level

has been selected, with the default duration of 1 hour. 12:30 is scheduled

as the end time. The programme will start automatically at 11:30 a.m.

The icons

and ash to indicate that programming has taken place.

After programming, in the time before the Fast Clean mode starts, the TIME

display indicates the duration and end of the Fast Clean mode alternately.

To cancel programming press the

button.

Once the automatic cleaning cycle is over

Before you can open the oven door, you will have to wait for the

icon to

switch off: this indicates the oven temperature has dropped to an acceptable

level. You will notice some white dust deposits on the bottom and the sides

of your oven; remove these deposits with a damp sponge once the oven

has cooled down completely. Alternatively, you can make use of the already

heated oven, in which case it is not necessary to remove the deposits, they

are completely harmless and will not affect your food in any way.

Troubleshooting

The “Clock button” and the digits on the

display flash.

Problem Possible cause Solution

The appliance has just been connected to the

electricity mains or there has been a blackout.

Set the clock.

A programmed cooking mode does not

start.

There has been a blackout.

Reprogram the cooking mode.

Only the high luminosity “Clock button”

is lit.

The appliance is in standby mode. Press any button to exit standby mode.

The temperature inside the oven is higher

than the suggested value for the selected

mode.

An automatic mode has been selected.

“Hot” appears on the display and

cooking does not start.

Wait for the oven to cool down.

Fan-assisted cooking has been

selected and the food looks burnt.

Positions 1 and 5: the direct heat could cause

temperature-sensitive foods to burn.

We recommend switching dripping pan

positions halfway through cooking.

Page is loading ...

60

PT

195123003.01

10/2014 - XEROX FABRIANO

Indesit Company S.p.A.

V

iale Aristide Merloni,47

60044 Fabriano (AN)

www.hotpoint.eu

Indesit FH 1039 P 0 IX/HA User guide

Indesit FH 1039 P 0 IX/HA User guide

in other languages

Related papers

Other documents