Panasonic EYFEA1N Owner's manual

Page is loading ...

- 4 -

Original instructions: English

Translation of the original instructions:

Other languages

I. INTENDED USE

These tools can be used to tighten

screws in clutch mode and to drill

holes in wood and metal in drill mode.

Additionally, model EYFEA1N can be

used to drill holes in soft concrete and

similar materials in hammer mode.

Read the Safety Instructions booklet

and the following before using.

II. ADDITIONAL

SAFETY RULES

1) Wear ear protectors.

Exposure to noise can cause hearing loss.

2) Use auxiliary handle supplied with

the tool.

Loss of control can cause personal injury.

3) Hold power tools by insulated

gripping surfaces when per-forming

an operation where the cutting tool

may contact hidden wiring; contact

with a “live” wire will make exposed

metal parts of the tool “live” and shock

the operator.

4) Wear a dust mask, if the work causes dust.

5) Be aware that this tool is always in an

operating condition, since it does not have

to be plugged into an electrical outlet.

6) When drilling or driving into walls,

oors, etc., “live” electrical wires may

be encountered. DO NOT TOUCH

THE CHUCK OR ANY FRONT METAL

PARTS OF THE TOOL! Hold the tool

only by the plastic handle to prevent

electric shock in case you drill or drive

into a “live” wire.

7) If the bit becomes jammed, im-mediately

turn the trigger switch off to prevent an

overload, which can damage the battery

pack or motor. Use reverse motion to

loosen jammed bits.

8) Do NOT operate the For-ward/Reverse

lever when the trigger switch is on. The

battery will discharge rapidly and dam-

age to the unit may occur.

9) During charging, the charger may

become slightly warm. This is normal.

Do NOT charge the battery for a long

period.

10) When storing or carrying the tool,

set the Forward/Reverse lever to the

center position (switch lock).

11) Do not strain the tool by holding the

speed control trigger halfway (speed

control mode) so that the motor stops.

12) Do not operate the speed selector

switch (LOW-HIGH) while pulling on

the speed control trigger. This can

cause the rechargeable battery to

wear quickly or damage the in-ternal

mechanism of the motor.

WARNING

Do not use other than the Panasonic bat-



tery packs that are designed for use with

this rechargeable tool.

Panasonic is not responsible for any dam-



age or accident caused by the use of recy-

cled or counterfeit battery pack.

Do not dispose of the battery pack in a re,



or expose it to excessive heat.

Do not drive the likes of nails into the bat-



tery pack, subject it to shocks, dismantle it,

or attempt to modify it.

Do not allow metal objects to touch the bat-



tery pack terminals.

Do not carry or store the battery pack in the



same container as nails or similar metal

objects.

Do not charge the battery pack in a high-



temperature location, such as next to a re

or in direct sunlight. Otherwise, the battery

may overheat, catch re, or explode.

Never use other than the dedicated charg-



er to charge the battery pack. Otherwise,

the battery may leak, overheat, or explode.

After removing the battery pack from the



tool or the charger, always reattach the

pack cover. Otherwise, the battery contacts

could be shorted, leading to a risk of re.

When the Battery Pack Has Deteriorated,



Replace It with a New One. Continued use

of a damaged battery pack may result in

heat generation, ignition or battery rupture.

EYFEA1N.indb 4 2011-3-9 15:16:06

- 5 -

Symbol Meaning

V Volts

Direct current

n

o

No load speed

...min

-1

Revolutions or reciprocations

per minutes

Ah

Electrical capacity of battery

pack

Rotation only

To reduce the risk of

injury, user must read and

understand instruction

manual.

For indoor use only.

III. ASSEMBLY

Attaching or Removing Bit

NOTE:

When attaching or removing a bit,

disconnect battery pack from tool or

place the switch in the center position

(switch lock).

1. Attachment

1

While pulling the bit holder

2

Insert the bit

3

Release the bit holder

2. Removal

1

While pulling the bit holder

2

Remove the bit

9.5 mm (3/8") - 13 mm (33/64") 6.35 mm (1/4")

Attaching or Removing Bat-

tery Pack

1. To connect the battery pack:

Insert the battery pack rmly into the

main body.

2. To remove the battery pack:

Push on the button from the side to

release the battery pack.

IV. OPERATION

[Main Body]

Switch Operation

1. The speed increases with the amount

of depression of the trigger. When

beginning work, depress the trigger

slightly to start the rotation slowly.

2. A feedback electronic controller is used

to give a strong torque even in low

speed.

3. The brake operates when the trigger

is released and the motor stops

immediately.

NOTE:

When the brake operates, a braking

sound may be heard. This is normal.

Button

EYFEA1N.indb 5 2011-3-9 15:16:06

- 6 -

Switch and Forward/Reverse

Lever Operation

CAUTION:

To prevent damage, do not operate

Forward/Reverse lever until the bit

comes to a complete stop.

Forward Rotation Switch

Operation

1. Push the lever for forward rotation.

2. Depress the trigger switch slightly to

start the tool slowly.

3. The speed increases with the amount

of depression of the trigger for efcient

tightening of screws and drilling.

The brake operates and the chuck

stops immediately when the trigger is

released.

4. After use, set the lever to its center

position (switch lock).

Reverse Rotation Switch

Operation

1. Push the lever for reverse rotation. Check

the direction of rotation before use.

2. Depress the trigger switch slightly to

start the tool slowly.

3. After use, set the lever to its center

position (switch lock).

Clutch Torque Setting

Adjust the torque to one of the 21 clutch

settings or “

” position.

Use for Drilling

When using for drilling, set the clutch at



“ ” position.

Use a bit designed for drilling.



CAUTION:

Set the clutch scale at the alignment

position before actual operation.

Forward Reverse

Switch lock

Setting Torque Use

1

Approx: 0.3 N·m

(3.0 kgf-cm or 2.6 in-lbs)

For

driving

screws

5

Approx: 1.0 N·m

(11 kgf-cm or 8.8 in-lbs)

9

Approx: 1.8 N·m

(18 kgf-cm or 15.9 in-lbs)

13

Approx: 2.5 N·m

(26 kgf-cm or 22.1 in-lbs)

17

Approx: 3.3 N·m

(33 kgf-cm or 29.2 in-lbs)

21

Approx: 4.0 N·m

(41 kgf-cm or 35.4 in-lbs)

Approx: 6 N·m

(61 kgf-cm or 53.1 in-lbs)

For

powerful

driving

screws

and

drilling

When using at high speeds, set the clutch



at 10 or below. (Operation stops at the

maximum torque of 1.5 N·m (15 kgf-cm)

when the scale is higher.)

The auto shut-off function may become



inoperable at high clutch settings when

battery power drops. Recharge the bat-

tery in that case.

Speed Selection

Choose a low or high speed to suit the use.

The more the variable speed control

trigger is pulled, the higher the speed

becomes.

CAUTION:

Check the speed selector switch be-



fore use.

Use at low speed when high torque



is needed during operation. (Using

at high speed when high torque is

required may cause a motor break-

down.)

HIGH

LOW

EYFEA1N.indb 6 2011-3-9 15:16:07

- 7 -

Do not operate the speed selector



switch (LOW-HIGH) while pulling on

the speed control trigger. This can

cause the rechargeable battery to

wear quickly or damage the internal

mechanism of the motor.

* See specifications for “MAXIMUM

RECOMMENDED CAPACITIES”.

CAUTION:

To prevent excessive temperature in-



crease of the tool surface, do not op-

erate the tool continuously using two

or more battery packs. The tool needs

cool-off time before switching to an-

other pack.

Do not close up vent holes on the



sides of the body during operation.

Otherwise, the machine function is

adversely affected to cause a failure.

Do NOT strain the tool (motor). This



may cause damage to the unit.

Use the tool in such a way as to pre-



vent the air from the body vent holes

from blowing directly onto your skin.

Otherwise, you may get burned.

Bit-locking Function

1. With the trigger switch not engaged

and a sc r ewdriv e r b it lo cked in

place, the tool can be used as a

manual screwdriver (up to 5 N·m,

51 kgf-cm, 44.3 in-lbs).

There will be a little play in the chuck,

but this is not a malfunction.

2. This feature is handy for tightening

screws that require more torque than

the maximum torque of the driver

(position

on the clutch), for conrming

the tightness of a screw or to loosen an

extremely tight screw.

How to Use Hook ring

WARNING!

When the main unit is held by the hook



ring, avoid jumping or running with it.

Doing so may cause the ring to slip and

the main unit may fall.

This may result in an accident or injury.

When the hook ring is not used, be



sure to return it to the original position.

The hook ring may catch on something.

This may result in an accident or injury.

When the unit is hooked by the hook



ring, do not attach driver bits to the unit.

A sharp edge object, such as a drill bit,

may cause injury or an accident.

Use a hooking tool (carabiner etc.) that



does not come off easily. If this unit falls

it may cause accident.

Using Hook Ring

1. Release the hook ring.

2. Attach the hook ring to the hooking tool.

•

Use a hooking tool (carabiner etc.)

that does not come off easily. If this

unit falls it may cause accident.

•

Ensure that there is no contact with

the surroundings when a hook ring is

used.

3. Return the hook ring after use.

Hooking tool

EYFEA1N.indb 7 2011-3-9 15:16:07

- 8 -

• Clutch Lock Cover

The clutch lock cover allows you to lock

the clutch at the selected setting.

Attaching the cover

1. Select the appropriate clutch setting for

the application.

2. Attach the clutch lock cover.

•

Align the triangle mark on the cover

with the graduation selection mark on

the drill and attach.

Tightening the screw to immobilize

the cover.

•

Use a hand screwdriver. Tightening the

screw too much may damage the cover.

*

Only use the screw that comes with the

clutch lock cover.

Removing the cover

1. Remove the clutch lock cover.

LED light

Pull the trigger.

The light illuminates

with very low current,

and it does not

adversely affect the

performance of the tool

during use or its battery

capacity.

CAUTION:

The built-in LED light is designed to



illuminate the small work area tempo-

rarily.

Do not use it as a substitute for a reg-



ular ashlight, since it does not have

enough brightness.

Caution: DO NOT STARE INTO BEAM.

Use of controls or adjustments or

performance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Automatic power-off function

The automatic power-off function is de-



signed to prevent a loss of tightening

torque due to reduced battery voltage.

Once it has been activated, the tool will

not operate until the battery pack has

been charged (or replaced with a fresh

unit), even if the trigger is depressed.

LED lamp will flash when the automatic



power-off function is activated.

LED lamp begins flashing, the battery



pack should be charged (or replaced with

a fresh unit) immediately.

Be sure to fully charge the battery pack



in question after activation of the auto-

matic power-off function. Failure to do

so may prevent the automatic power-off

function from being properly deactivated.

[Battery Pack]

For Appropriate Use of

Battery Pack

Li-ion Battery Pack

For optimum battery life, store the Li-ion



battery pack following use without charg-

ing it.

When charging the battery pack, conrm



that the terminals on the battery charger

are free of foreign substances such as

dust and water etc. Clean the terminals

before charging the battery pack if any

foreign substances are found on the ter-

minals.

The life of the battery pack terminals may

be affected by foreign substances such

as dust and water etc. during operation.

When battery pack is not in use, keep it



away from other metal objects like: paper

clips, coins, keys, nails, screws, or other

small metal objects that can make a con-

nection from one terminal to another.

Shorting the battery terminals together

may cause sparks, burns or a re.

When operating the battery pack, make



sure the work place is well ventilated.

Triangle mark

Graduation selection mark

EYFEA1N.indb 8 2011-3-9 15:16:08

- 9 -

When the battery pack is removed from the



main body of the tool, replace the battery

pack cover immediately in order to prevent

dust or dirt from contaminating the battery

terminals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have

a limited life. If the operation time

b e c om e s e x t r em e l y s h o rt a f t e r

recharging, replace the battery pack

with a new one.

Battery Recycling

ATTENTION:

For environmental protection and

recycling of materials, be sure that it

is disposed of at an officially assigned

location, if there is one in your country.

[Battery Charger]

Charging

CAUTION:

If the temperature of the battery pack



falls approximately below −10°C (14°F),

charging will automatically stop to pre-

vent degradation of the battery.

The ambient temperature range is be-



tween 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the

battery temperature is below 0°C (32°F),

the tool may fail to function properly.

When charging a cool battery pack (below



0°C (32°F)) in a warm place, leave the bat-

tery pack at the place and wait for more

than one hour to warm up the battery to the

level of the ambient temperature.

Cool down the charger when charging



more than two battery packs consecutively.

Do not insert your fingers into contact



hole, when holding charger or any other

occasions.

To prevent the risk of re or damage to the

battery charger.

Do not use power source from an engine



generator.

Do not cover vent holes on the charger



and the battery pack.

Unplug the charger when not in use.



NOTE:

Your battery pack is not fully charged at

the time of purchase. Be sure to charge

the battery before use.

Battery charger

1. Plug the charger into the AC outlet.

2. Insert the battery pack firmly into the

charger.

3. During charging, the charging lamp

will be lit.When charging is completed,

an internal electronic switch will

automatically be triggered to prevent

overcharging.

Charging will not start if the battery



pack is warm (for example, immedi-

ately after heavy-duty operation).

The orange standby lamp will be

flashing until the battery cools down.

Charging will then begin automatically.

4. The charge lamp (green) will flash

slowly once the battery is approximately

80% charged.

5. When charging is completed, the

charging lamp in green color will turn off.

6. If the temperature of the battery pack

is 0°C or less, charging takes longer to

fully charge the battery pack than the

standard charging time.

Even when the battery is fully charged,

it will have approximately 50% of the

power of a fully charged battery at

normal operating temperature.

7. Consult an authorized dealer if the

charging lamp (green) does not turn off.

8. If a fully charged battery pack is

inserted into the charger again, the

charging lamp lights up. After several

minutes, the charging lamp in green

color will turn off.

EYFEA1N.indb 9 2011-3-9 15:16:08

- 10 -

LAMP INDICATIONS

Charging is completed. (Full charge.)

Battery is approximately 80% charged.

Now charging.

(Green)

Turn off Lit

Flashing

(Orange)

Charger is plugged into the AC outlet. Ready to charge.

Charging Status Lamp.

Left: green Right: orange will be displayed.

Battery pack is cool, or the voltage of the battery is low.

The battery pack is being charged slowly to reduce the load on the battery.

Battery pack is warm.

Charging will begin when temperature of battery pack drops. If

the temperature of the battery pack is -10° or less, the charging

status lamp (orange) will also start ashing. Charging will begin

when the temperature of the battery pack goes up.

Charging is not possible. Clogged with dust or malfunction of

the battery pack.

Information for Users on Collection and Disposal of Old

Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying

documents mean that used electrical and electronic products and batteries

should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used

batteries, please take them to applicable collection points, in accordance

with your national legislation and the Directives 2002/96/EC and 2006/66/

EC.

By disposing of these products and batteries correctly, you will help to save

valuable resources and prevent any potential negative effects on human

health and the environment which could otherwise arise from inappropriate

waste handling.

For more information about collection and recycling of old products and

batteries, please contact your local municipality, your waste disposal

service or the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in

accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

EYFEA1N.indb 10 2011-3-9 15:16:08

- 11 -

[Information on Disposal in other Countries outside the

European Union]

These symbols are only valid in the European Union. If you wish to discard these

items, please contact your local authorities or dealer and ask for the correct method of

disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it

complies with the requirement set by the Directive for the chemical involved.

V. MAINTENANCE

Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner, benzine,

or other volatile solvents for cleaning.

In the event that the inside of the tool or battery pack is exposed to water, drain and

allow to dry as soon as possible.

Carefully remove any dust or iron lings that collect inside the tool. If you experience any

problems operating the tool, please contact your nearest authorised service center.

VI. ACCESSORIES

Use only bits suitable for size of drill's chuck.

VII. APPENDIX

MAXIMUM RECOMMENDED CAPACITIES

Model EYFEA1N

Screw

driving

Machine screw

Low : M5

High : M4

VIII. SPECIFICATIONS

MAIN UNIT

Model EYFEA1N

Motor voltage 7.2 V DC

No load

speed

Low 0 - 300 min

-1

(rpm)

High 0 - 900 min

-1

(rpm)

Maximum

torque

Low 6.0 N·m (61 kgf-cm, 53.24 in-lbs)

High 2.0 N·m (20 kgf-cm, 17.75 in-lbs)

Clutch torque

Approx. 0.3 N·m (3 kgf-cm, 2.6 in-lbs) –

4.0 N·m (41 kgf-cm, 35.6 in-lbs)

Overall length 145 mm (5-7/10")

Weight (with battery pack) 0.63 kg (1.39 lbs)

EYFEA1N.indb 11 2011-3-9 15:16:08

- 12 -

BATTERY PACK

Model EY9L20

Storage battery Li-ion

Battery voltage 7.2 V DC (3.6 V × 2 cells)

Charging time

Usable: 35 min

Full: 60 min

NOTE: This chart may include models that are not available in your area.

Please refer to the latest general catalogue.

For the dealer name and address, please see the included warranty card.

BATTERY CHARGER

Model EY0L20

Rating See the rating plate on the bottom of the charge.

Weight 0.43 kg (0.95 lbs)

NOTE: This chart may include models that are not available in your area.

Please refer to the latest general catalogue.

NOTE: For the dealer name and address, please see the included warranty card.

EYFEA1N.indb 12 2011-3-9 15:16:08

Page is loading ...

- 102 -

EN. GR. FR. IT. ND. ES. DN. SW. NR. FN

EY9710FEA12 2011 03 Printed in Japan

EYFEA1N.indb 102 2011-3-9 15:16:31

Panasonic EYFEA1N Owner's manual

Panasonic EYFEA1N Owner's manual

in other languages

Related papers

Other documents