iON Complete LP Owner's manual

Page is loading ...

2

FM ANT

Quickstart Guide (English)

Box Contents

Complete LP

Felt Slipmat

45 RPM Adapter

Quickstart Guide

Safety & Warranty Manual

Support

For the latest information about this product (system requirements, compatibility information,

etc.) and product registration, visit ionaudio.com.

• A minimum distance of 6 inches must be maintained to provide sufficient ventilation of

the rear bass ports.

• Do not stand it on a thick pile carpet, or install it in a place with poor air flow.

• Place the unit on a flat even surface, away from vibrating sources.

Quick Setup

Connection Diagram

Items not listed under the Box Contents are sold separately.

Tablet

Power

Speakers

(optional)

3

20

21

22

Features

Front Panel

1. CD/USB: Toggles the source from CD to

USB.

2. AM/FM: Press and release to switch between

the AM and FM radio bands when Tuner has

been selected as the mode.

3. Repeat: Repeats a single track or the whole

disc of a CD.

4. Random: Plays a random track on a CD.

5. USB Rec: Press to go to USB recording

mode if a USB flash drive is connected.

6. Standby/On (EU/UK units only): On EU/UK models,

the Standby button powers the unit on/off.

7. Standby LED (EU/EK units only): Indicates you are in

Standby mode. Complete LP will go to sleep and

illuminate this LED after 60 minutes of inactivity, unless

music is playing via Bluetooth or the radio.

8. FM ST: This illuminates when station is being received

in stereo.

9. Open/Close: Opens/closes the CD tray.

10. Stop: Press to end the recording to the USB flash

drive.

11. Prev / Tune/Track / Seek: Press to go to the previous

USB file, radio station, or CD track. Hold to “seek”

backwards (jump to the strongest radio station signal).

12. Play/Pause: Starts or pauses playback of a CD, USB

file, or Bluetooth track. When in Tuner mode, press for

2 seconds to “scan” through the radio stations. When

in Bluetooth mode, hold Play/Pause for 2 seconds to

disconnect a currently paired Bluetooth device.

13. Next / Tune/Track / Seek: Press to go to the next

USB file, radio station, or CD track. Hold to “seek”

(jump to the next strongest radio station signal).

14. Mode: Switches from BT/AUX/TUNER/CD/TAPE/USB/

PHONO modes.

15. Volume: Adjusts the sound level for the internal

speakers as well as the headphone output.

16. Line In: Connect the output from a line-level device to

this input, such as from a smartphone, media player,

tablet, etc.

17. Power: Press to power the unit on/off.

Note (EU/UK units only): To fully power on Complete LP, also press Standby.

18. Display: Shows the current mode, track number, track time, and radio station.

Note: The display and surrounding buttons include a plastic protector on it. Remove

these for optimal viewing.

19. CD Tray: Press the Open/Close button to eject the tray and place a CD here. This unit is

designed to play commercially available CDs, properly burned and finalized CD-Rs, CD-

RW’s, and MP3 CDs. Due to variances on the specification of certain CD burners and

CDs, we recommend burning CDs at the minimum speed possible for the best playback

performance.

20. Headphone Output: When headphones are connected, the internal speaker is muted.

21. Tuning: Adjust this to go to another radio station.

22. USB: Playback tracks from your USB flash drive or record to the USB flash drive.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

4

Rear Panel

1. Line Output: Connect external speakers to this output.

2. Speakers: These internal speakers output the music.

3. Bass Ports: These provide extended bass for the music. Position these away from walls

or other obstructions for best sound quality.

4. Tapedeck: Insert a cassette tape here.

5. Power Input: The integrated power cable is connected here.

6. FM Antenna: Adjust this wire for better FM radio reception. For AM reception, rotate the

unit until the best reception is found.

Recording

Note: It is not possible to record from the AM/FM radio.

When in BT/TAPE/PHONO/AUX mode:

1. Connect your USB flash drive to Complete LP.

2. Press USB REC.

3. Press USB REC to begin recording.

4. Once the display shows “REC”, USB flashes in the top left corner of the display,

recording will begin.

5. Press STOP to end recording and it will save the audio file to your USB flash drive.

When in CD/MP3 mode:

1. Connect your USB flash drive to Complete LP.

2. Press USB REC.

3. Press NEXT/PREV to toggle between these options:

• REC ONE (record one track)

• REC DIR (record all songs from the current folder)

• REC ALL (record all the songs)

4. Press USB REC to begin recording. Once the display shows “READING”, USB will flash

on the screen and begin recording.

5. Press STOP to end recording and it will save the audio file to your USB flash drive.

1

2

3

4

3

5

FM ANT

6

5

Playback

Bluetooth Mode

1. Turn on your Bluetooth device.

2. Press the Mode button until BT AUX is seen on the display. It will automatically go into

pairing mode to search for Bluetooth devices.

3. Navigate to your Bluetooth device’s setup screen, find “Complete LP”, and connect.

Note: If your Bluetooth device prompts for a pairing code, enter “0000”.

Tape Player Mode

1. Press the Mode button until TAPE is seen on the display.

2. Insert the tape with the thicker side of the tape facing to the right of tape tray.

3. Push the Eject/Fast Forward button 1/2 way down to toggle between fast forward and

play mode.

4. Push the Eject/Fast Forward button completely down to eject the tape.

Note: Remove your 1/8” (3.5 mm) cable from the Line In before going to Tuner mode in order

to hear the station.

Vinyl Mode

1. Platter – Place your record here.

2. 45 RPM Adapter Holder – Holds the included

45 RPM adapter. When not using the adapter,

please place it in this holder.

3. Tonearm – The fixed tonearm can be raised

and lowered by hand, or by pressing the raise

/ lower lever.

4. Arm Clip – This specially designed arm clip

secures the tonearm while at rest or when not

in use. The arm clip has been designed to

remain in the up position while unlocked.

5. Raise / Lower Lever – Raises and lowers the

tonearm.

6. 33 / 45 / 78 Switch – This switch controls the

speed of the turntable platter.

Note: For best results when playing 78 RPM

vinyl records, use a 78 stylus (sold separately).

Only use a 78 stylus with 78 RPM vinyl records.

7. Autostop switch – This switch turns autostop

on or off. When autostop is on, the platter will

start spinning when the tonearm is placed over

the record and stop spinning when the record

has reached the end. (When Autostop is off, the

platter will always spin regardless of the

position of the tonearm.)

Note: If your vinyl record stops before it

reaches the end of the music, turn Autostop to

the off position for this particular record. This is

generally recommended for 45 RPM records.

IMPORTANT: Remove the plastic

cartridge cover (needle cover) before

operating the turntable.

*WARNING: The RCA outputs are LINE

level. Please only connect these to LINE

level inputs. You may damage your

receiver if you plug in a LINE level device

into a PHONO level input.

IMPORTANT: Place the included felt

slipmat on the platter; then place your

record on the felt slipmat to carefully hold

your records.

1

2

3

4

5

7

6

Playing your records:

1. Press the Mode button until PHONO is seen on the display.

2. Set the Speed Control switch to the desired speed (33 1/3, 45, 78 rpm).

3. Place the record on the platter and adjust the tonearm on the record to begin playback.

4. Adjust the Volume knob on Complete LP.

Note: Remove your 1/8” (3.5 mm) cable from the Line In before going to Tuner mode in order to hear the station.

Aux Mode

1. Connect your device to the Line In using a stereo 1/8” (3.5mm) cable.

2. Press the Mode button until BT AUX is seen on the display.

3. Adjust the volume from your output device.

CD Mode

1. Press the Open/Close button to insert a MP3, CD-R, or CD-RW into the CD tray.

2. Press the Mode button until CD is seen in the display.

3. Press PREV/NEXT to select a different track.

4. Press PLAY/PAUSE to play or pause a track.

Note: Remove your 1/8” (3.5 mm) cable from the Line In before going to Tuner mode in order to hear the station.

USB Mode

1. Connect a USB flash drive to the unit.

2. Press the CD/USB button until USB is seen on the display. It will automatically start playback of the songs on

the USB flash drive.

3. Press PREV/NEXT to select a different track.

4. Press PLAY/PAUSE to play or pause a track.

Note: Remove your 1/8” (3.5 mm) cable from the Line In before going to Tuner mode in order to hear the station.

Tuner Mode

1. Press AM/FM to toggle between the AM and FM bands.

2. Adjust the TUNE knob to select the channel you want.

3. Hold either the PREV or NEXT button to go to the strongest radio station signal.

Note: Remove your 1/8” (3.5 mm) cable from the Line In before going to Tuner mode in order to hear the station.

To save a radio station as a preset:

1. Press the OPEN/CLOSE button.

2. Change the preset slot by pressing the PREV or NEXT button while the preset slot number is still flashing.

3. Press OPEN/CLOSE to confirm your save.

4. Toggle between saved presets using the PREV or NEXT button when in Tuner mode.

Troubleshooting

I am playing a record but do not hearing any audio:

• If you are playing music from vinyl:

o Make sure that Complete LP is powered on and that the needle is on the record.

o If headphones are connected to Complete LP, disconnect the headphones in order to hear sound from

the internal speakers.

My record is not playing at the correct speed; its pitch is too high or too low:

o Ensure the 33 / 45 / 78 switch is set to the correct speed for your record.

I am connected to a Bluetooth speaker but do not hear any audio.

o Turn Complete LP off and then on again, and then try pairing it again.

o Use the volume knob on Complete LP to turn up the Bluetooth output level.

o If headphones are connected to Complete LP, disconnect the headphones in order to hear sound from

the internal speakers.

I am not hearing the radio station.

o Remove your 1/8” (3.5 mm) cable from the Line In before going to Tuner mode in order to hear the radio

station.

7

Technical Specifications

Speaker Output Power

8W (peak)

Supported Bluetooth Profile

4.0

Bluetooth Range

30 feet (10 meters) or better

Power

12W

Cartridge Type

ceramic

Cartridge and Stylus CZ-800-10

Voltage

120V, 60 Hz (US)

230V, 50 Hz (EU)

240V, 50 Hz (UK)

Power Consumption

≤ 19W

Dimensions

(width x depth x height)

11.75" x 19.75" x 9.2"

29.8 cm x 50.1 cm x 23.4 cm

Weight

17.2 lbs.

7.8 kg

Radio Frequency Range US: EUROPE: JAPAN:

AM 520 – 1710 kHz AM 522 – 1629 kHz AM 520 – 1710

FM 87.5 – 107.9 MHz FM 87.5 – 108 MHz FM 75.5 – 90.5

Specifications are subject to change without notice.

* Bluetooth range is affected by walls, obstructions, and movement. For optimal performance, place the product in the center

of the room so it is unobstructed by walls, furniture, etc.

Trademarks and Licenses

ION Audio is a trademark of ION Audio, LLC, registered in the U.S. and other countries.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by

ION Audio is under license.

All other product or company names are trademarks or registered trademarks of their respective owners.

Page is loading ...

ionaudio.com

Manual Version 1.1

iON Complete LP Owner's manual

iON Complete LP Owner's manual

in other languages

Related papers

Other documents