Whirlpool AQ105D 69D EU AQUALTIS Owner's manual

EN

1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Care and maintenance, 4

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Precautions and advice, 5

General safety

Load balancing system

Disposal

Opening the porthole door manually

Description of the machine, 6-7

Touch control panel

Running a wash cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent

Preparing the laundry

Washing recommendations

Trouble shooting, 11

Assistance, 12

WASHING MACHINE

Instructions for

installation and use

English,1

EN

AQUALTIS

AQ105D 69D

DE

Deutsch,13 Nederlands,25

NL

ES

Español,37

PT

Português,49

IT

Italiano,61

FR

Français,73

EN

2

Installation

! This instruction manual should be kept in a

safe place for future reference. If the washing

machine is sold, given away or moved, please

ensure the manual is kept with the machine,

so that the new owner may benefit from the

advice contained within it.

! Read these instructions carefully: they

contain vital information relating to the safe

installation and operation of the appliance.

! Inside the pack containing this manual, you

will also find the guarantee and all the details

necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging

from the washing machine, make sure it has not

been damaged during transportation. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4

protective screws

(used during

transportation) and

the corresponding

spacer, located on

the rear part of the

appliance (see figure).

3. Close off the holes using the plastic plugs

supplied in the pack.

4. Keep all the parts in a safe place; they will

be needed again if the washing machine is

moved to another location, to prevent the

inside of the appliance being damaged.

! Packaging materials should not be used as

toys for children.

Levelling

1. Place the washing machine on a flat sturdy

floor, without resting it up against walls or

cabinets.

2. If the floor is

uneven, the front feet

of the machine may

be adjusted until it

reaches a horizontal

position (the angle of

inclination must not

exceed 2 degrees).

! If the appliance is levelled correctly, it will

be more stable and much less likely to cause

vibrations and noise while it is operating,

particularly during the spin cycle.

! If it is placed on carpet or a rug, adjust the

feet in such a way as to allow a sufficient

ventilation space underneath the washing

machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

! Before connecting the inlet hose to the water

supply, run the water until it is perfectly clear.

1. Connect the inlet

hose to the machine

by screwing it onto

the cold water inlet of

the appliance, which

is situated on the top

right-hand side of

the rear part of the

appliance (see figure).

2. Connect the inlet

hose by screwing it to

a cold water tap using

a 3/4 gas threaded

connection (see

figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical data table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

EN

3

Technical data

Model

AQ105D 69D

Dimensions

width 59.5 cm

height 85 cm

depth 64,5 cm

Capacity

from 1 to 10 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 71 litres

Spin speed

up to 1600 rotations per

minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

programme

;

Cotton standard 60°C.

programme ;

Cotton standard 40°C.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

Connecting the drain hose

Connect the drain

hose to drain duct

piping or a wall drain

located between 65

and 100 cm above

the floor, making sure

it is not bent at all.

Alternatively, rest the

drain hose on the

side of a washbasin

or bathtub, fastening

the duct supplied to

the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the

electricity socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in

the Technical data table (see opposite);

• the power supply voltage falls within the

values indicated in the Technical data table

(see opposite);

• the socket is compatible with the plug of the

appliance. If this is not the case, have the

socket or the plug replaced.

! The machine must not be installed outdoors,

even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! The mains socket must remain within easy reach

after the washing machine has been installed.

! Do not use extension cords or multiple

sockets.

! The cable should not be bent or compressed.

! The power supply cable and plug must only

be replaced by authorised technicians.

Warning! The company shall not be held

responsible in the event that these regulations

are not respected.

65 - 100 cm

EN

4

Care and maintenance

Cutting off the water and

electricity supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system in

the machine and help to prevent leaks.

• Unplug the appliance when cleaning it and

during all maintenance work.

Cleaning the machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards (2)

(see figure).

Wash it under running

water; this procedure

should be repeated

frequently.

Caring for your appliance drum

• Always leave the door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. take off the cover panel on the front of the

machine by first pressing it in the centre and

then pushing downwards on both sides until

you can remove it (see figures);

2. position a container

so that it will collect the

water which flows out

(approximately 1.5 l)

(see figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

1

2

1

2

1

2

EN

5

Precautions and tips

! The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• If it must be moved, proceed with the help of two or

three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs

the distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health.

The crossed-out dustbin is marked on all products

to remind the owner of their obligations regarding

separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their local

authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if

it is not, remove excess

water using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is freed

from its stop position; pull

downwards until you hear a

“click”, which indicates that

the door is now unlocked.

5. open the door; if this is

still not possible repeat the

procedure.

6. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

EN

6

Description of the machine

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

DIRECT INJECTION SYSTEM

The washing machine features the innovative “Direct

Injection” technology that quickly solubilises the detergent

and efficiently activates all the various components. The

system guarantees the complete use and dissolution of

the detergent, which is mixed with water before reaching

the garments. This ensures better cleaning results already

at low temperatures, providing significant energy savings

while perfectly protecting colours and fibres. The “Direct

Injection” technology is activated automatically in all the

cycles.

ADJUSTABLE FEET

TOUCH CONTROL PANEL

To adjust the settings, gently

press the icon inside the

sensitive (touch control) area

as illustrated in the figure.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF button briefly and

wait for the machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 0,5 W

PORTHOLE DOOR

Always use the handle to

open the porthole door (see

figure).

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside the

machine and can be accessed

by opening the door.

For more information on

detergent measures, please

refer to the chapter entitled

“Detergents and laundry”.

1. pre-wash compartment:

use powder detergent.

! Before pouring in the detergent,

make sure that extra compartment

3 has been removed.

2. main wash compartment:

If liquid detergent is used,

it is recommended that the

removable plastic partition A

(supplied) be used for proper

dosage.If powder detergent is

used, place the partition into slot

B.

3. extra compartment: Bleach

! The use of extra compartment 3 excludes the pre-

wash function.

washing additives compartment: for fabric softener

or liquid additives. We recommend that the maximum

level indicated by the grille is not exceeded, and that

concentrated fabric softeners are diluted.

3

1

2

1

8

0

2

1

0

1

5

0

1

2

0

9

0

6

0

B

A

EN

77

WASH CYCLE

SELECTOR knob

Button with ON/OFF

indicator light

Touch control panel

Button with ON/OFF indicator light: press this briefly to switch

the machine on or off. The green indicator light indicates that the

machine is switched on. To switch off the washing machine during

the wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the machine

will not switch off. If the machine is switched off during a wash

cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in either

direction. To select the most suitable wash cycle, please refer

to the “Table of wash cycles”.

The knob will not move during the wash cycle.

M1-M2-M3 buttons: press and hold one of the buttons to

store a cycle with your own set preferences in the memory

of the machine. To recall a previously-stored cycle, press the

corresponding button.

TEMPERATURE button: press to modify or exclude the

temperature setting; the value selected will appear on the

display above (see “Running a wash cycle”).

SPIN CYCLE button: press to modify or exclude the spin

cycle; the value selected will appear on the display above (see

“Running a wash cycle”).

DELAYED START button: press to set a delayed start for

the selected wash cycle; the set delay time will appear on the

display above (see “Running a wash cycle”).

OPTION buttons: press to select the available options. The

indicator light corresponding to the selected option will remain

lit (see “Running a wash cycle”).

WASH CYCLE PHASE icons: these illuminate to indicate the

progress of the wash cycle (Wash – Rinse – Spin –

Drain ). The text lights up when the cycle is complete.

START/PAUSE button with indicator light: when the green

indicator light flashes slowly, press the button to start a wash

cycle. Once the cycle has begun the indicator light will remain

lit in a fixed manner. To pause the wash cycle, press the button

again; the indicator light will flash in an orange colour. If the

“Door locked” indicator light is switched off, the door may

be opened. To start the wash cycle from the point at which it

was interrupted, press the button again.

DOOR LOCKED indicator light: indicates that the porthole

door is locked. To open the door, pause the wash cycle (see

“Running a wash cycle”).

CONTROL PANEL LOCK button with indicator light: to

activate or deactivate the control panel lock, press and hold

the button for approximately 2 seconds. when the indicator

light is illuminated, the control panel is locked (apart from the

ON/OFF button).. This means it is possible to prevent wash

cycles from being modified accidentally, especially where there

are children in the home.

ECO indicator light: the icon lights up when, after altering the

washing parameters, an energy saving of at least 10% is made.

Furthermore, before the machine enters “Standby” mode, the

icon will light up for a few seconds; when the machine is switched

off the estimated energy saving will be around the 80% mark.

CHANGE LANGUAGE.

The first time the machine is switched on, the first language

will flash on the display. The “ “, “OK” and “V” symbols will

appear on the display, in line with the 3 buttons on the right-

hand side. The languages change automatically every 3”;

alternatively, they can be changed by pressing the buttons next

to the “ “ and “V” symbols. Use the “OK” button to confirm the

language, which will be set after 2”. If no buttons are pressed,

the automatic language change will begin again after 30”.

To change the language, switch the machine on and off

again; in the 30” time period after it has been switched off,

press and hold the temperature +spin +delayed start

buttons simultaneously for 5’’. A short sound alert will be emitted

and the set language will flash on the display. Press the buttons

next to the “ “ and “V” symbols to change the language. Use the

button next to the “OK” symbol to confirm the language, which

will be set after 2”. If no buttons are pressed, the language set

previously will be displayed after 30”. Switch on the machine.

TEMPERATURE

button

OPTION

buttons

SPIN

button

DISPLAY

M1

M3

ECO

indicator light

DELAYED START

button

START/PAUSE button

with indicator light

DOOR LOCKED indicator light

WASH

CYCLE

PHASE

icons

CONTROL PANEL LOCK

button with indicator light

M2

EN

8

WARNING: before you use the washing machine for the

first time, run a wash cycle with detergent and no laundry,

using the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the button. All

the indicator lights will illuminate for 1 second and the

text AQUALTIS will appear on the display; the indicator

light corresponding to the button will then remain lit in

a constant manner and the START/PAUSE indicator light

will flash.

2. SELECT THE PROGRAMME. Turn the PROGRAMME

KNOB left or right, until the required programme has

been selected; the name of the programme will appear

on the display. A temperature and spin speed is set for

each programme; these may be adjusted. The cycle

duration will also appear on the display.

3. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

4. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Description

of the machine”.

5. CLOSE THE PORTHOLE DOOR.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons on the control panel:

Modify the temperature and/or spin

speed.

The machine automatically displays the maximum

temperature and spin speed values set for the selected

cycle, or the most recently-used settings if they are

compatible with the selected cycle. The temperature can

be decreased by pressing the button, until the cold

wash “OFF” setting is reached. The spin speed may be

progressively reduced by pressing the button, until

it is completely excluded “OFF”. If these buttons are

pressed again, the maximum values are restored.

! Exception: if the

programme is selected, the

temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. During the setting procedure,

the delay period and the text “Starts in:” will be

displayed, along with the flashing symbol. After the

delayed start has been set, the symbol will remain

fixed on the display, which will also indicate the duration

of the selected cycle with the text “Ends in:” and the

cycle duration. Press the DELAYED START button just

once to display the delay time set previously.

After the countdown has begun, the display will show

the text “Starts in:” and the delay period. Once the

set delay time has elapsed, the machine will begin its

cycle and the display will show “Ends in:” and the time

remaining until the end of the cycle.

To remove the delayed start option, press the button

until the display shows the text OFF; the symbol will

disappear.

Modify the cycle settings.

• Press the button to activate the option; the name

of the option will then appear on the display and

the corresponding indicator light will illuminate.

• Press the button again to deactivate the option; the

name of the option will then appear on the display

followed by the text OFF, and the corresponding

indicator light will switch off.

! If the selected option is not compatible with the

selected wash cycle, this incompatibility will be signalled

by the flashing of the indicator light and a sound alert

(3 beeps); the option will not be activated.

! If the selected option is not compatible with another

option that has been selected previously, the indicator

light corresponding to the first option selected will

flash and only the second option will be activated; the

indicator light corresponding to the button will remain lit

in a constant manner.

! The options may affect the recommended load value and/

or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light remains lit

in a fixed manner and the porthole door locks (the

DOOR LOCKED indicator light illuminates). The icons

corresponding to the wash cycle phases will light up

during the cycle to indicate which phase is currently in

progress.

To change a wash cycle once it has already started,

pause the washing machine by pressing the START/

PAUSE button; then select the desired cycle and press

the START/PAUSE button again.

To open the door during a wash cycle, press the START/

PAUSE button; if the DOOR LOCKED indicator light is

switched off you may open the door. Press the START/

PAUSE button again to restart the wash cycle from the

point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may be

opened immediately. If the START/PAUSE indicator light

is flashing, press the button to end the cycle. Open the

door, unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button until the cycle stops and the

machine switches off.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you

to wash even the most valuable and delicate garments

in complete confidence thanks to the special bag which

protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you wash

quilts and padded items with an outer layer made

using synthetic material.

Running a wash cycle

EN

99

Wash cycles and options

Wash options

Super Wash

This option offers a high-

performance wash due to the

greater quantity of water used in

the initial phase of the cycle, and

due to the increased wash cycle

duration, is particularly useful for

the removal of stubborn stains.

It can be used with or without

bleach. If you desire bleaching,

insert the extra tray compartment

(3) into compartment 1. When

pouring in the bleach, be careful not to exceed the “max” level

marked on the central pivot (see figure). To bleach laundry

without carrying out a full wash cycle, pour the bleach into the

extra compartment 3, select the “Rinse” cycle and activate

the “Super Wash” option .

! It cannot be used in conjunction with , , , , , ,

, , , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased

and optimal residual detergent removal is guaranteed. It is

particularly useful for skin which is sensitive to detergents. We

recommend this option is used with a full load of washing, or

when a large amount of detergent is required.

! It cannot be used in conjunction with , , , , , .

Easy Iron

By selecting this option, the wash and spin cycles will be

modified in order to reduce the formation of creases.

At the end of the cycle the washing machine drum will

rotate slowly; the “Easy Iron” and START/PAUSE indicator

lights will flash. To end the cycle press the START/PAUSE

button or the “Easy Iron” button.

! It cannot be used in conjunction with , , , , , .

Prewash

If this function is selected, the pre-wash cycle will run; this is

useful for removing stubborn stains.

N.B.: put the detergent in the relevant compartment.

! It cannot be used in conjunction with , , , , ,

, , , , , , (60°), .

Table of wash cycles

Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value will then be shown on the display.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as

water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

3) At 60 °C the “Prewash” function cannot be selected.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.

4) Long wash cycle for synthetics: set wash cycle with a temperature of 40°C.

Icon

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergent and addi-

tives

Max. load (kg)

Residual dam-

pness %

Energy con-

sumption kWh

Total water lt

Cycle duration

Prewash

Wash

Bleach

Fabric

softener

Synthetics Resistant 60° 800

   

5 48 1,21 74 125’

Synthetics Resistant (4) 40° 800

   

5 48 0,71 72 105’

Coloureds Intensive

40° 1600

 

-



9 - - - 175’

Multi Colour

20° 1600 -



-



9 - - - 185’

Darks

30° 800 -



-



6 - - - 80’

Shirts

40° 600 -

  

2,5 - - - 85’

Duvets: for down-stuffed garments. 30° 1200 -



-



3,5 - - - 120’

Bed&Bath for bedlinen and towels. 60° 1600

   

10 - - - 160’

Rinse

- 1600 - -

 

10 - - - 49’

Spin and Pump out - 1600 - - - - 10 - - - 16’

Anti Allergy Plus

60° 1600 -



-



6 - - - 210’

Anti Allergy Delicate

40° 1600 -



-



6 - - - 230’

Ultradelicates

30° 0 -



-



1 - - - 80’

Wool: for wool, cashmere, etc. 40° 800 -



-



2,5 - - - 105’

Mix 30': to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

30° 800 -



-



4 71 0,20 44 30’

Cotton Standard 60°C (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1600

(3)

  

10 44 0,95 60 200’

Cotton Standard 40°C (2): lightly soiled whites and delicate colours. 40° 1600 -

  

10 44 0,92 88 185’

3

1

2

EN

10

Detergents and laundry

Shirts: use the special wash cycle to wash shirts in

different fabrics and colours to guarantee they receive the

best possible care.

Duvets: to wash double or single duvets (the weight of which

should not exceed 3,5 kg), cushions or clothes padded with

goose down such as puffa jackets, use the special wash

cycle. We recommend that duvets are placed in the drum

with their edges folded inwards (see figure) and that no more

than ¾ of the total volume of the drum is used. To achieve the

best results, we recommend that a liquid detergent is used

and placed inside the detergent dispenser drawer.

Quilts: to wash quilts with a synthetic outer layer, use the

bag provided and set the wash cycle to .

Bedlinen and towels: Use programme to wash bed

linen and towels in one single cycle: it optimises softener

performance and helps you save time and energy. We

recommend the use of powder detergent

Anti Allergy Plus : cycle studied for cotton laundry and

other resistant fabrics to guarantee the removal of the main

allergens such as pollen, mites, cat and dog hair.

Anti Allergy Delicate : cycle studied for cotton laundry

and other resistant fabrics to guarantee the removal of

pollen and cat and dog hair already at 40°.

Ultradelicates: use programme to wash very delicate

garments having strasses or sequins.

We recommend turning the garments inside out before

washing and placing small items into the special bag

for washing delicates. Use liquid detergent on delicate

garments for best results.

To wash Silk garments and Curtains (these should be folded

and placed inside the bag provided), select cycle and then

option (in this case it will also be possible to enable the

“Extra Rinse” option); the machine will end the cycle while

the laundry is soaking and the indicator light will flash.

To drain the water so that the laundry may be removed,

press the START/PAUSE button or the button.

Wool: the wool wash cycle on this Hotpoint-Ariston

machine has been tested and approved by The

Woolmark Company for washing wool garments labelled

as hand washable provided that the garments are

washed according to the instructions on the garment

label and those issued by the manufacturer of this

washing machine. Hotpoint-Ariston is the first washing

machine brand to be approved by The Woolmark

Company for Apparel Care- Platinum for its washing

performance and consumption of energy and water.

(M1135)

Detergent

The type and quantity of detergent required depend on the

type of fabric you are washing (cotton, wool, silk, etc.), as

well as its colour, the washing temperature, the level of soiling

and the hardness of the water in the area. Measuring out the

detergent carefully will avoid wastage and help to protect the

environment: although they are biodegradable, detergents still

contain ingredients which alter the balance of nature.

We recommend the following:

• use powder detergents for white cotton garments and

pre-washing.

• use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.

• use gentle liquid detergents for wool and silk garments.

The detergent should be poured into the relevant

compartment - or the dispenser placed directly inside the

drum - before the wash cycle begins. In the latter case, it will

not be possible to select the Cottons with pre-wash cycle.

! Use powder detergent for white cotton garments, for

pre-washing, and for washing at temperatures over 60°C

! Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

• Shake out the garments before loading them into the machine.

• Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

• Empty all pockets and check the buttons;

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillowcase 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Washing recommendations

Coloureds Intensive: use the cycle on light coloured

garments to remove tough stains without damaging

the integrity and brightness of the colours. The cycle

is studied to guarantee a 60° performance at only 40°.

We recommend the use of detergents suitable to wash

coloured clothes.

Multi Colour: use the cycle to wash medium-soiled

multi-coloured garments or garments of different colours.

Cycle designed to ensure colour care while achieving a 40°

performance at just 20°. We recommend using detergents

that are suitable for coloured washes and active already at

low temperatures.

! We always recommend a separate wash for running

garments and the first time you wash a new coloured item.

Darks: use cycle to wash dark-coloured garments.

This programme is designed to maintain dark colours

over time. We recommend using a liquid detergent for the

best results when washing dark-coloured garments.

EN

11

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),

make sure that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water.

The washing machine door

remains locked.

The machine continuously fills

with water and drains.

The washing machine does not

drain or spin.

The machine vibrates a lot during

the spin cycle.

The washing machine leaks.

The icons corresponding to the

“Phase in progress” flash rapidly

at the same time as the ON/OFF

indicator light.

There is too much foam.

The washing machine door

remains locked.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make

contact.

• There is no power in the house.

• The door is not closed properly.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set.

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• If you have selected the function, at the end of the cycle the washing

machine drum will rotate slowly; to end the cycle press the START/PAUSE

button or the button.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• If the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washing machine to fill with

water and drain continuously. Special anti-draining valves are available in shops

and help to prevent this inconvenience.

• The wall drainage system is not fitted with a breather pipe.

• The wash cycle does not include draining: Some wash cycles require the drain

phase to be started manually (see “Wash cycles and options”).

• The option is enabled: to complete the wash cycle, press the START/

PAUSE button (“Wash cycles and options”).

• The drain hose is bent (see Installation).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The machine is not level (see “Installation” ).

• The machine is trapped between cabinets and walls (see “Installation”).

• The load is unbalanced (see “Detergents and laundry”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser is blocked (to clean it, see “Care and maintenance”).

• The drain hose is not fixed in place properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

• Perform the manual unlocking procedure (see “Precautions and tips”).

! Note: to exit “Demo mode”, switch machine off, press and hold the two and buttons simultaneously for 3 seconds.

EN

12

Before calling for Assistance:

• Check whether you can solve the problem by yourself (see “Trouble shooting”);

• Restart the wash cycle to check whether the problem has been solved;

• If it has not, contact the Authorised Technical Assistance Service.

! If the washing machine has been installed or used incorrectly, you will have to pay for the call-out service.

! Always request the assistance of authorised technicians.

Please have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

The above information can be found on the data plate located on the appliance itself.

Assistance

Page is loading ...

Whirlpool AQ105D 69D EU AQUALTIS Owner's manual

This manual is also suitable for

Whirlpool AQ105D 69D EU AQUALTIS Owner's manual

in other languages

Related papers