Grizzly T10880 Owner's manual

Brand: Grizzly

Model: T10880

Category: Vacuum cleaner supplies

Type: Owner's manual

Grizzly T10880 is a dust collector with a HEPA filter upgrade kit that can be used to improve the air quality in your workshop. The T10880 has a powerful motor that can generate up to 1,350 CFM of airflow, which is enough to handle even the most demanding dust-producing applications. The HEPA filter upgrade kit traps 99.97% of particles down to 0.3 microns in size, making it ideal for use in applications where fine dust is a concern.

Some of the potential use cases for the Grizzly T10880 dust collector include:

Woodworking: The T10880 can be used to collect dust from woodworking machines such as saws, sanders, and routers.

Some of the potential use cases for the Grizzly T10880 dust collector include:

Woodworking: The T10880 can be used to collect dust from woodworking machines such as saws, sanders, and routers.

Model T10880 & T10881

G0442 & G0601 Cartridge Filter Replacement

with HEPA Filter Upgrade Kit

Step One:

Remove the filter L-braces from the blower housing, as shown above, by loosening and removing (6) 5/16” x

1” hex bolts, (12) 5/16” flat washers, and (6) 5/16” hex nuts. Remove and set the cartridge filter aside.

Step Two:

Remove the outlet port from the blower housing by loosening and removing (4) 5/16” x 1” hex bolts, (8) 5/16”

flat washers, and (4) 5/16” hex nuts.

Step Three:

Remove the mounting bracket that secures the intake barrel to the upper stand leg by loosening and removing (8)

5/16” x 1” hex bolts, (16) 5/16” flat washers, and (8) 5/16” nuts. Next, loosen and remove (8) 3/8” x 3/4” hex

bolts, (16) 3/8” flat washers, and (8) 3/8” nuts on the leg stand side. NOTE: Replace the mounting brackets with

the new types one at a time. DO NOT remove all old mounting brackets at once.

Step Four:

After each mounting bracket has been replaced with the new type, make sure to tighten all the bolts and nuts

securely before moving on to the next step.

Step Five:

Attach the rubber gasket to the outlet opening on the blower housing, then attach the outlet connector by

securing and fastening (10) 3/8” x 1” hex bolts, (20) 3/8” flat washers, and (10) 3/8” nuts.!

Step Six:

Assemble the HEPA leg stand, which consists of three segments: upper, middle and lower. Secure and fasten

using (8) 3/8” x 1” hex bolts, (16) 3/8” flat washers, and (8) 3/8” nuts. !

Step Seven:

Attach the HEPA leg stand to the outlet connector, as shown above, by securing and fastening (4) 3/8” x 1” hex

bolts, (8) 3/8” flat washers, and (4) 3/8” nuts. !

Step Eight:

Attach the rubber gasket to the square top of the HEPA filter, as shown above. Take the filter adapter and attach

it to the square top of the HEPA filter with (16) 5/16” x 1” hex bolts and 5/16” flat washers. Tighten and secure

all bolts and nuts.

Step Nine:

Attach the rubber gasket to the outlet opening, then attach the filter adapter and HEPA filter to the blower

housing with (16) 3/8” x 1” hex bolts, (30) 3/8” flat washers, and (14) 3/8” nuts. Tighten and secure all bolts

and nuts.

Step Ten:

Fit the plastic canister collection bag over the bottom of the HEPA canister filter, and clamp in place with the

metal bag clamp, as shown above.

UPGRADE COMPLETE!

Grizzly T10880 Owner's manual

Brand: Grizzly

Model: T10880

Category: Vacuum cleaner supplies

Type: Owner's manual

Some of the potential use cases for the Grizzly T10880 dust collector include:

Woodworking: The T10880 can be used to collect dust from woodworking machines such as saws, sanders, and routers.

Download PDF

report

Grizzly T10880 Owner's manual

Grizzly T10880 Owner's manual

Related papers

Other documents