Samsung AE080RXYDGG/EU User manual

Air to Water Heat Pump

Installation manual

Mono Outdoor Unit AE***RXYDEG / AE***RXYDGG

࡙ Thank you for purchasing this Samsung Product.

࡙ Before operating this unit, please read this installation manual carefully and retain it for future

reference.

2

Contents

Safety precautions ..........................................................................................................3

Product specications.......................................................................................................5

Outdoor unit specication...................................................................................................6

Application examples .......................................................................................................7

Main components...........................................................................................................9

Functional diagram .......................................................................................................13

Installing the unit .........................................................................................................14

Piping work...............................................................................................................26

Wiring ....................................................................................................................32

Testing operations ........................................................................................................40

Error codes................................................................................................................42

Maintenance..............................................................................................................44

Charging refrigerant ......................................................................................................47

Troubleshooting ..........................................................................................................48

Commissioning ...........................................................................................................51

Recommissioning instructions ............................................................................................51

3

ENGLISH

Safety precautions

Carefully follow the precautions listed as below because they are essential to guarantee the safety of SAMSUNG product.

WARNING

t Always disconnect a power supply of Air-Water Heat Pump before servicing it or accessing

components inside the unit.

t Verify that installation and testing operations shall be performed by qualied personnel.

t To prevent serious damage on the system and injuries to users, precautions and other

notices shall be observed.

Warning

f Carefully read the content of this manual before installing the air to water heat pump and store the manual in a safe place

in order to be able to use it as reference after installation.

f For maximum safety, installers should always carefully read the following warnings.

f Store the provided manual in a safe location with end user after installation, and remember to hand it over to the new

owner if the Heat pump unit is sold or transferred.

f This manual explains how to install Air-Water Heat Pump. The use of other types of units with dierent control systems

may damage the units and invalidate the warranty. The manufacturer shall not be responsible for damages arising from

the use of non compliant units.

f The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper

connection of electric and hydraulic lines. Failure to comply with these instructions or to comply with the requirements

set forth in the “Operating limits” table, included in the manual, shall immediately invalidate the warranty.

f Failure to comply with these instructions or to comply with the requirement on the Operating Range (Heat: -25~35°C/

Cool: 10~46°C) set forth in the Product Specication (p.5) shall immediately invalidate the warranty.

f Do not use the units if you see some damages on the units and recognize something bad such as loud noisy, smell of

burning.

f In order to prevent electric shocks, res or injuries, always stop the unit, disable the protection switch and contact

SAMSUNG’s technical support if the unit produces smoke, if the power cable is hot or damaged or if the unit is very noisy.

f Always remember to inspect the unit, electric connections, refrigerant tubes and protections regularly. These operations

shall be performed by qualied personnel only.

f The unit contains moving parts and electrical parts, which should always be kept out of the reach of children.

f Do not attempt to repair, move, alter or reinstall the unit by unauthorized personnel, these operations may cause product

damage, electric shocks and res.

f Do not place containers with liquids or other objects on the unit.

f All the materials used for the manufacture and packaging of the air to water heat pump are recyclable.

f The packing material and exhaust batteries of the remote controller(optional) must be disposed of in accordance with

local regulations.

f The air to water heat pump contains a refrigerant that has to be disposed of as special waste. At the end of its life cycle,

the heat pump must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly

and safely.

f Wear protective gloves to unpack, move, install, and service the unit to avoid your hands being injured by the edge of the

parts.

f Do not touch the internal parts (water pipes, refrigerant pipes, heat exchangers, etc) while running the units. And if you

need to adjust and touch the units, have enough time for the unit can be cooled and be sure to wear protective gloves.

f In case of refrigerant leakage, try to avoid getting in contact with the refrigerant because this could result in severe

wounds.

f When you install the Air to water heat pump in a small room, you must consider a proper ventilation to prevent a leakage

level within the maximum permissible limit.

- In that case, you may die from suocation by some possibility.

4

f Make sure to safely dispose of packing materials. Packing materials, such as nails and other metal or wooden pallets may

cause children get injured.

f Inspect the product shipped and check if damaged during transport. If the product has some damages, DO NOT INSTALL

and immediately discuss about the damages with the carrier or retailer (if the installer or the authorized technician has

collected the material from the retailer.)

f Our units shall be installed in compliance with the spaces described in the installation manual, to ensure accessibility

from both sides and allow repairs or maintenance operations to be carried out. If the units installed without complying

with procedures described in manual, additional expenses can be asked because special harnesses, ladders, scaolding

or any other elevation system for repair service will NOT be considered part of the warranty and will be charged to the

end customer.

f Always make sure that the power supply is compliant with local safety standards.

f Verify that the voltage and frequency of the power supply comply with the specications and input power is sucient to

ensure the operation of any other domestic appliance connected to the same electric lines. Always verify that the cut-o

and protection switches are suitably selected.

f Always verify that electric connections (cable entry, section of leads, protections…) are compliant with the electric

specications and with the instructions provided in the wiring scheme. Always verify that all connections comply with

the standards applicable to the installation of air to water heat pumps. Devices disconnected from the power supply

should be completely disconnected in the condition of overvoltage category.

f Do not connect the earth wire to the gas pipe or water pipe, lighting rod, surge absorber, or telephone earth wire. If

earthing is not complete, it may cause an electric shock or re.

f Be sure to install both an earth leakage detector and circuit breaker with specied capacity in accordance with relevant

local and national regulations.

- If it is not installed properly, it may cause electric shocks and re.

f Make sure that the condensed water runs well out of the unit at low ambient temperature. Drain pipe and cond heater

can frost/ice can not grow. If drain work is not eective for releasing condensed water, it can make the units get damaged

by massive ice and system can be stop , covered by ice.

f Install the power cable and communication cable of the indoor and outdoor unit at least 1m away from the electric

appliance.

f Protect the unit from rats or small animals. If an animal makes a contact with the electric parts, it can cause malfunctions,

smoke or re. Please instruct the customer to keep the area around the unit clean.

f Do not disassemble and alter the heater at your own discretion.

f Be sure not to perform power cable modication, extension wiring, and multiple wire connection.

- It may cause electric shock or re due to poor connection, poor insulation, or current limit override.

- When extension wiring is required due to power line damage, refer to “How to connect your extended power cables” in

the installation manual.

f Do not use means to accelerate the defrost operation or to clean, other than those recommended by Samsung.

f Do not pierce or burn.

f Be aware that refrigerants may not contain an odour.

Safety precautions

5

ENGLISH

Product specications

Product line-up

Line-up Remark

Heat pump units

Chassis

-

Model name

AE080RXYDEG

AE080RXYDGG

AE120RXYDEG

AE120RXYDGG

AE160RXYDEG

AE160RXYDGG

Auxiliary parts

Control kit

MIM-E03CN Requisite

Accessories

f Keep supplied accessories until the installation is nished.

f Hand the installation manual over to the customer after nishing installation.

f The quantities are indicated in parentheses.

Installation manual (2) Drain plug (1) Rubber Leg(4) Drain cap (3)

6

Outdoor unit specication

Type Unit AE080RXYDEG AE120RXYDEG AE160RXYDEG

Power source -

1Φ, 220~240VAC 50Hz

3Φ, 380~415VAC 50Hz

1Φ, 220~240VAC 50Hz

3Φ, 380~415VAC 50Hz

1Φ, 220~240VAC 50Hz

3Φ, 380~415VAC 50Hz

Refrigerant g 1,150 (R-32) 2,200 (R-32) 2,200 (R-32)

Noise

(Heat/Cool, Pressure)

dB(A) 48/48 50/50 52/54

Water connection

(In/Out)

Inch 1.0 1.0 1.0

Leaving water

temperature

°C

Heating : 25~65

Cooling : 5~25

Heating : 25~65

Cooling : 5~25

Heating : 25~65

Cooling : 5~25

Operating range

(Heat/Cool)

°C -25~35/10~46 -25~35/10~46 -25~35/10~46

Weight (net/gross) kg 76.0/84.5 110/119 110/119

Size (WxHxD, net) mm 940 x 998 x 330 940 x 1,420 x 330 940 x 1,420 x 330

Type Unit AE080RXYDGG AE120RXYDGG AE160RXYDGG

Power source -

1Φ, 220~240VAC 50Hz

3Φ, 380~415VAC 50Hz

1Φ, 220~240VAC 50Hz

3Φ, 380~415VAC 50Hz

1Φ, 220~240VAC 50Hz

3Φ, 380~415VAC 50Hz

Refrigerant g 1,150 (R-32) 2,200 (R-32) 2,200 (R-32)

Noise

(Heat/Cool, Pressure)

dB(A) 48/48 50/50 52/54

Water connection

(In/Out)

Inch 1.0 1.0 1.0

Leaving water

temperature

°C

Heating : 25~65

Cooling : 5~25

Heating : 25~65

Cooling : 5~25

Heating : 25~65

Cooling : 5~25

Operating range

(Heat/Cool)

°C -25~35/10~46 -25~35/10~46 -25~35/10~46

Weight (net/gross) kg 75.0/83.5 111/120 111/120

Size (WxHxD, net) mm 940 x 998 x 330 940 x 1,420 x 330 940 x 1,420 x 330

❋ At the temperature -25 °C ~ -20 °C, operation is available but capacity cannot be guaranteed.

7

ENGLISH

Application examples

t The application examples given below are for illustration purposes only.

t When the SAMSUNG Air-to-Water Heat Pump system is used in series with another heat source (e.g. gas

boiler), ensure that the return water temperature not exceed 65°C.

t The unit is only to be used in a closed water system. Application in an open water circuit can lead to excessive

corrosion of the water piping.

t SAMSUNG can not be put responsible for incorrect or unsafe situations in the water system. Make sure that the

boiler, radiators, convectors, solar collectors, UFHs, FCUs, additional pumps, pipings, and controls in the water

system are in accordance with relevant local laws and regulations under the installer's responsibility.

t By-pass valve shall be installed for space heating loops. When one of loops or all loops are closed , water ow

rate could be low condition. To keep ow rate approximately and prevent ow stop, the by-pass valve shall be

installed between supply collector and return collector.

t SAMSUNG shall not be held liable for any damage resulting from not observing this rule.

t SAMSUNG do not provide specic water system components such as Pressure relief valve, Air vent valve, buer

tank and etc. Installers and end-users shall consider how to install the above designated components in overall

water system depending on the installation conditions. If the components are not installed in appropriate

location, the water system can not be operated as designed.

WARNING

Application #1

Mono outdoor + Control kit

Outdoor Mechanical room Indoor

Solar collector

Solar signal input

DHW sensor input

& Booster heater output

Back up boiler

operation output

Booster heater

Zone Controller #1 (Radiators)

Zone Controller #2 (UFHs)

Wired controller

(provided by SAMSUNG)

Shut-O &

Drain valve

Strainer

Pressure

relief valve

3.0 bar

Air-vent

Bypass

valve

Bypass valve

Air-vent

50 ~ 55°C

35°C

45°C

Primary

pump

Expansion

tank

3-way valve

Balancing Vessel

Mixing valve

Secondary

Pump #1

Drain

Control Kit

(provided by SAMSUNG)

DHW tank

Outdoor unit

Solar pump

Supply header

Return header

Under- Floor Heating Coils

Radiators or convectors

TW4

8

Application examples

Application #2

Mono outdoor + Tank Integrated Hydro Unit

Outdoor unit

[ Supply Scope ]

Tank Integrated Hydro Unit

Balancing Vessel

Back up Boiler

Operation

Back-up Boiler

Room Controller

Zone Control

Supply Header

Return Header

Supply Header

Return Header

Under-Floor Heating Coils

Radiators or Convectors

45°C

35°C

Water

pump #2

Water

pump #1

Outdoor Indoor Mechanical Room

Tw2_z1

Tw2_z2

9

ENGLISH

Main components

Dimensions(Overall)

Heat pump for R-32.

1-Fan chassis

f AE080RXYD**

620

330

360

384

940

973

998

(Unit : mm)

2-Fan chassis

f AE120RXYD**/AE160RXYD**

620

330

360

384

940

1395

1420

(Unit : mm)

10

Main components

Dimensions (Water pipe)

AE080RXYD** AE120RXYD**/AE160RXYD**

513.4

244.4

WATER OUT

WATER IN

151.5

83.5

WATER OUT

WATER IN

(Unit : mm) (Unit : mm)

11

ENGLISH

AE080RXYD**

NO. Name Note.

PHE Danfoss, H30L series

Base heater SUS316L, 150W

Water tting BSPP 1" Male

12

Main components

AE120RXYD**/AE160RXYD**

NO. Name Note.

PHE Danfoss, B3-030 series

Base heater SUS316L, 150W

Water hose in Rubber hose

Water hose out Rubber hose

Water tting BSPP 1" Male

13

ENGLISH

Functional diagram

PHE

T/S #3

Charging

port

Charging

port

4WAY

v/v

T/S #4

Comp

Filter

HP s/w

Filter

Exp. v/v

Accum

T/S #5

T/S #6

T/S #2(TW2)

T/S #1(TW1)

Part Description

PHE Plate heat exchanger

T/S #1 For water inlet temp sensor

T/S #2 For water outlet temp sensor

T/S #3 For PHE temp sensor

T/S #4 For discharge temp

T/S #5 For cond temp

T/S #6 For ambient temp sensor

Charging port For refrigerants

Accum Accumulator

14

Installing the unit

Moving the outdoor unit

f Select the moving route in advance.

f Be sure that moving route is safe from weight of the outdoor unit.

f Do not slant the product more than 30˚when carrying it. (do not lay the product down sideways)

f The surface of the heat exchanger is sharp. Be carefule not to be injured while moving and installing.

Moving the outdoor unit by wire rope

f Fasten the outdoor unit by two 8m or longer wire ropes as shown at the

gure. To prevent from damage or scratches, insert a piece of cloth between

the outdoor unit and rope, then move the unit.

Plate protection

cloth

Wire rope

❋ The appearance of the unit may be

dierent from the picture depending

on the model.

Moving the outdoor unit with a fork lift

f Insert the fork into the wooden pallet at the bottom of the outdoor unit

carefully. Be careful that the fork does not damage the outdoor unit.

Wooden pallet

Fork lift

15

ENGLISH

Deciding on where to install the outdoor unit

Decide the installation location regarding the following condition and obtain the user’s approval.

f The outdoor unit must not be placed on its side or upside down, as the compressor lubrication oil will run into the cooling

circuit and seriously damage the unit.

f Choose a location that is dry and sunny, but not exposed to direct sunlight or strong winds.

f Do not block any passageways or thoroughfares.

f Choose a location where the noise of the Air to Water Heat Pump when running and the discharged air do not disturb

any neighbours.

f Choose a position that enables the pipes and cables to be easily connected to the other hydrauric system.

f Install the outdoor unit on a at, stable surface that can support its weight and does not generate any unnecessary noise

and vibration.

f Position the outdoor unit so that the air ow directly stream towards the open area.

f Place the outdoor unit where there are no plants and animals because they may cause malfunction of outdoor unit.

f Maintain sucient clearance around the outdoor unit, especially from a radio, computer, stereo system, etc.

Installation Guide at the seashore

Make sure to follow below guides when installing at the seashore.

1. Do not install the product in a place where it is directly exposed to sea water and sea breeze.

- Make sure to install the product behind a structure (such as building) that can block see breeze.

- Even when it is inevitable to install the product in seashore, make sure that product is not directly exposed to sea

breeze by installing a protection wall.

2. Consider that the salinity particles clinging to the external panels should be suciently washed out.

3. Because the residual water at the bottom of the outdoor unit signicantly promotes corrosion,

make sure that the slope does not disturb drainage.

- Keep the oor level so that rain does not accumulate.

- Be careful not to block the drain hole due to foreign substance

4. When product is installed in seashore, periodically clean it with water to remove attached salinity.

5. Make sure to install the product in a place that provides smooth water drainage. Especially, ensure that the base part has

good drainage.

6. If the product is damaged during the installation or maintenance, make sure to repair it.

7. Check the condition of the product periodically.

- Check the installation site every 3 months and perform anti-corrosion treatment such as R-Pro supplied by SAMSUNG

(Code : MOK-220SA) or commercial water repellent grease and wax, etc., based on the product condition.

- When the product is to be shut down for a long period of time, such as o-peak hours, take appropriate measures like

covering the product.

8. If the product installed within 500m of seashore, special anti-corrosion treatment is required.

❋ Please contact your local SAMSUNG representative for further details.

Sea

Sea breeze

Outdoor

unit

16

Installing the unit

Sea

Sea breeze

Outdoor

unit

Protection wall

Sea

Sea breeze

Outdoor

unit

Protection wall should be constructed with a solid material that

can block the sea breeze and the height and width of the wall

should be 1.5 times larger than the size of the outdoor unit. (You

must secure more than 700mm of space between the protection

wall and the outdoor unit for air circulation.)

t Depending on the condition of power supply, unstable power or voltage may cause malfunction of the parts or

control system. (At the ship or places using power supply from electric generator, etc).

CAUTION

f Do not install the Air to Water Heat Pump in following places.

t The place where there is mineral oil or arsenic acid. There is a chance that parts may get damaged due to burned resin.

The capacity of the heat exchanger may reduce or the Air to Water Heat pump may be out of order.

t The place where corrosive gas such as sulfurous acid gas generates from the vent pipe or air outlet. The copper pipe or

connection pipe may corrode and refrigerant may leak.

t The place where there is a danger of existing combustible gas, carbon ber or ammable dust. The place where thinner

or gasoline is handled.

t This device must be installed according to the national electrical rules.

t With an outdoor unit having net weight upper than 60kg, we suggest do not install it suspended on wall, but

considering oor standing one.

CAUTION

f If the outdoor unit is installed at a height, ensure that its base is rmly xed in position.

f Make sure that the water dripping from the drain hose runs away correctly and safely.

f When you install the outdoor unit at wayside, you should install it above 2m height or make sure that the heat from the

outdoor unit shouldn't be in direct contact with passersby. (The ground for application :The revision of regulation for

facility in building by the law of the Ministry of Construction and Transportation.

f While in installation or relocation of the product, do not mix the refrigerant with other gases including air or unspecied

refrigerant. Failure to do so may cause pressure increase to result in rupture or injury.

f Do not cut or burn the refrigerant container or pipings.

f Use clean parts such as manifold gauge, vacuum pump, and charging hose for the refrigerant.

f Installation must be carried out by qualied personnel for handling the refrigerant. Additionally, reference the regulations

and laws.

f Be careful not to let foreign substances (lubricating oil, refrigerant other than R-32, water, etc.) enter the pipings.

f When mechanical ventilation is required, ventilation openings shall be kept clear of obstruction.

f For disposal of the product, follow the local laws and regulations.

f Do not work in a conned place.

f The work area shall be blocked.

f The refrigerant pipings shall be installed in the position where there are no substances that may result in corrosion.

17

ENGLISH

f The following checks shall be performed for installation:

- The ventilation devices and outlets are operating normally and are not obstructed.

- Markings and signs on the equipment shall be visible and legible.

f Upon leakage of the refrigerant, ventilate the room. When the leaked refrigerant is exposed to ame, it may cause

generation of toxic gases.

f Make sure that the work area is safe from ammable substances.

f To purge air in the refrigerant, be sure to use a vacuum pump.

f Note that the refrigerant has no odour.

f The units are not explosion proof so they must be installed with no risk of explosion.

f This product contains uorinated gases that contribute to global greenhouse eect. Accordingly, do not vent gases into

the atmosphere.

f For installation with handling the refrigerant(R-32), use dedicated tools and piping materials.

f Servicing and installation shall be performed as recommended by the manufacturer. In case other skilled persons are

joined for servicing, it shall be carried out under supervision of the person who is competent in handling ammable

refrigerants.

f For servicing the units containing ammable refrigerants, safety checks are required to minimise the risk of ignition.

f Servicing shall be performed following the controlled procedure to minimize the risk of ammable refrigerant or gases.

f Do not install where there is a risk of combustible gas leakage.

f Do not place heat sources.

f Be cautious not to generate a spark as follows:

- Do not remove the fuses with power on.

- Do not disconnect the power plug from the wall outlet with power on.

- It is recommended to locate the outlet in a high position. Place the cords so that they are not tangled.

f If the indoor unit is not R-32 compatible, an error signal appears and the unit will not operate.

f After installation, check for leakage. Toxic gas may be generated and if it comes into contact with an ignition source such

as fan heater, stove, and cooker. cylinders, make sure that only the refrigerant recovery cylinders are used.

f Never directly touch any accidental leaking refrigerant.

f This could result in severe wounds caused by frostbite.

18

Installing the unit

Preparation of re extinguisher

f If a hot work is to be done, an appropriate re extinguishing equipment should have been available.

f A dry powder or CO re extinguisher shall be equipped near the charging area.

Ignition sources free

f Make sure to store the units in a place without continuously operating ignition sources (for example, open ames, an

operating gas appliance or an operating electric heater).

f The service engineers shall not use any ignition sources with the risk of re or explosion.

f Potential ignition sources shall be kept away from the work area where the ammable refrigerant can possibly be

released to the surrounding.

f The work area should be checked to ensure that there are no ammable hazards or ignition risks. The “No Smoking” sign

shall be attached.

f Under no circumstances shall potential sources of ignition be used while in detection of leakage.

f Make sure that the seals or sealing materials have not degraded.

f Safe parts are the ones with which the worker can work in a ammable atmosphere. Other parts may result in ignition

due to leakage.

f Replace components only with parts specied by Samsung. Other parts may result in the ignition of refrigerant in the

atmosphere from a leak.

Area ventilation

f Make sure that the work area is well ventilated before performing a hot work.

f Ventilation shall be made even during the work.

f The ventilation should safely disperse any released gases and preferably expel them into the atmosphere.

f Ventilation shall be made even during the work.

Leakage detection methods

f The leakage detector shall be calibrated in a refrigerant-free area.

f Make sure that the detector is not a potential source of ignition.

f The leakage detector shall be set to the LFL (lower ammability limit).

f The use of detergents containing chlorine shall be avoided for cleaning because the chlorine may react with the

refrigerant and corrode the pipings.

f If leakage is suspected, naked ames shall be removed.

f If a leakage is found while in brazing, the entire refrigerant shall be recovered from the product or isolated (e.g. using

shut-o valves). It shall not be directly released to the environment. Oxygen free nitrogen (OFN) shall be used for purging

the system before and during the brazing process.

f The work area shall be checked with an appropriate refrigerant detector before and during work.

f Ensure that the leakage detector is appropriate for use with ammable refrigerants.

19

ENGLISH

Labelling

f The parts shall be labelled to ensure that they have been decommissioned and emptied of refrigerant.

f The labels shall be dated.

f Make sure that the labels are axed on the system to notify it contains ammable refrigerant.

Recovery

f When removing refrigerant from the system for servicing or decommissioning, it is recommended to remove the entire

refrigerant.

f When transferring refrigerant into cylinders, make sure that only the refrigerant recovery cylinders are used.

f All cylinders used for the recovered refrigerant shall be labelled.

f Cylinders shall be equipped with pressure relief valves and shut-o valves in a proper order.

f The recovery system shall operate normally according to the specied instructions and shall be suitable for refrigerant

recovery.

f In addition, the calibration scales shall operate normally.

f Hoses shall be equipped with leak-free disconnect couplings.

f Before starting the recovery, check for the status of the recovery system and sealing state. Consult with the manufacturer

if suspected.

f The recovered refrigerant shall be returned to the supplier in the correct recovery cylinders with the Waste Transfer Note

attached.

f Do not mix refrigerants in the recovery units or cylinders.

f If compressors or compressor oils are to be removed, make sure that they have been evacuated to the acceptable level to

ensure that ammable refrigerant does not remain in the lubricant.

f The evacuation process shall be performed before sending the compressor to the suppliers.

f Only the electrical heating to the compressor body is allowed to accelerate the process.

f Oil shall be drained safely from the system.

f Never install a motor-driven equipment to prevent ignition.

f Empty recovery cylinders shall be evacuated and cooled before recovery.

Installation location requirements

f The outdoor unit shall be installed in an open space that is always ventilated.

f The local gas regulations shall be observed.

f For installation inside a building (this applies either to indoor or outdoor units installed inside) a minimum room oor

area of space conditioned is mandatory according to IEC 60335-2-40:2018 (see the reference table into either the indoor

or outdoor unit installation manual).

f To handle, purge, and dispose the refrigerant, or break into the refrigerant circuit, the worker should have a certicate

from an industry-accredited authority.

20

Installing the unit

Space requirements for outdoor unit

When installing 1 outdoor unit

(Unit : mm)

300 or more

1,500 or more

❋ When the air outlet is opposite the wall ❋ When the air outlet is towards the wall

300 or more

300 or more 600 or more

1,500 or more

2,000 or more

❋ When 3 sides of the outdoor unit are blocked by the

wall

❋ The upper part of the outdoor unit and the air outlet

is towards the wall

600 or more

300 or more

1,500 or more

300 or more

❋ The upper part of the outdoor unit and the air outlet

is opposite the wall

❋ When front and rear side of the outdoor unit is

towards the wall

Page is loading ...

Samsung AE080RXYDGG/EU User manual

Samsung AE080RXYDGG/EU User manual

Related papers

Other documents