Eldes EWM1 User guide

WIRELESS POWER SOCKET

USER GUIDE

V1.0

EWM1

Contents of Pack

1 x 1 x

EN LTRU DE

Page is loading ...

4 EN

1. GENERAL OPERATIONAL

DESCRIPTION

MAIN FEATURES:

• Control your household equipment remotely by

wireless keyfob, keypad, ELDES Cloud Services or

automaically by scheduled ime or system event

• Compaible with any 230V electrical appliance

• View real-ime, daily and monthly power con-

sumpion report

• Fault indicaion and protecion: circuit thermal,

overvoltage, overcurrent, undervoltage, relay

fault indicaion

Control

(turn

ON/OFF)

Power

consumpion

monitoring

Fault

indicaion

ESIM364

  (by EKB2)  (by EKB2)

EPIR3



ELDES

Cloud

Services

  

EN 5

EWM1 is a wireless device intended to expand

ELDES alarm system capabiliies by providing a

wireless connecion access to any 230V electrical

appliance, such as lights, air-condiioner, watering

equipment etc. By plugging the appliance into the

electrical outlet of EWM1, the user gains a possibil-

ity to control it by wireless keyfob, keypad, sched-

uled ime or a speciic system event. In addiion,

EWM1 lets you monitor the power consumpion

and view the reports. In addiion, the for safety and

protecion purposes EWM1 will prevent from pow-

ering up the electrical appliance if certain fault con-

diions are present (see 4. FAULT INDICATIONS)

In order to start using EWM1, it has to be paired

with ELDES alarm system using ELDES Conigu-

raion Tool sotware or by sending a corresponding

SMS text message to ELDES alarm system.

It is possible to connect up to 16 EWM1 devices to

EPIR3 system, while to ESIM364 alarm system -

up to 32 EWM1 devices at a ime. The maximum

wireless connecion range is 150m (492.13t) (in

open areas).

6 EN

LED indicaion

Type E, F

or G outlet

Buton for restoring

default parameters or

turning ON/OFF EWM1

when paired with

ELDES alarm system

LED indicaion Descripion

Flashing (green)

EWM1 is unpaired or

wireless connecion with

ELDES alarm system

is lost

Steady ON (red) Fault is present

OFF Relay is turned OFF

Steady ON (green) Relay is turned ON

Flashing (red)

EWM1 is reseing to

default

TYPE F TYPE G TYPE E

EWM1-E (type E) EWM1-F (type F)

TYPE F TYPE G TYPE E

EWM1-G (type G)

EN 7

2. CONFIGURING AND PAIRING

WITH THE SYSTEM

For more details on how to

conigure and pair the device

with the system, please refer

to EL DES Coniguraion Tool

sot ware’s HELP secion or

ELDES alarm system’s instal-

laion/user manual.

3. EWM1 PGM

OUTPUT AND TAMPER

Upon successful EWM1 pairing process, the system

adds 1 wireless PGM output intended for electrical ap-

pliance connecion, control and power consumpion

monitoring and 1 Instant-type wireless zone (by default

- disabled) for tamper control.

Once the wireless zone is enabled, the wireless con-

necion loss between EWM1 and ELDES alarm sys-

tem would lead to tamper alarm followed by SMS text

message to the listed user (-s) (by default - disabled)

as well as fault indica ion by the keypad. The SMS text

ELDES

Coniguraion Tool

If you are unable to pair the wireless de-

vice, please restore the parameters of the

wireless device to default and try again

(see 5. RESTORING DEFAULT PARAM-

ETERS for more details)

8 EN

message contains the wireless device model, wireless

ID code and tamper name. However, the delivery of the

data message to the monitoring staion regarding this

event is permanently disabled for EWM1 device.

4. FAULT INDICATIONS

For safety and protecion purposes, EWM1 will

instantly power down/prevent from powering up

the electrical appliance plugged into EWM1 outlet

when the following faults are present:

• OVERVOLTAGE – voltage has increased

above 260VAC.

• UNDERVOLTAGE – voltage has dropped be-

low 190VAC.

• OVERCURRENT – current has increased

above 12,5A.

• RELAY FAULT – unable to power up the appli-

ance due to faulty relay.

• TEMP. FAULT – the environmental temper-

ature has dropped below -35°C (-31°F) or in-

creased above +90°C (+194°F).

In addiion, the user can view the exising faults

by EKB2 key pad (only for ESIM364) or by access-

ing the ELDES Cloud Services account. In order to

clear the exising faults, please press the but-

ton on EWM1, turn OFF the electrical appliance or

EN 9

turn OFF the wireless PGM output associated with

EWM1.

5. RESTORING

DEFAULT PARAMETERS

1. Unplug EWM1 from the household electricity

socket.

2. Press and hold the buton.

3. Plug in EWM1 back to the electricity socket

4. Hold the buton unil red LED indicator

shortly lashes several imes.

5. Release the buton.

10 EN

6. TECHNICAL SPECIFICATIONS

Compaible with:

• ESIM364 v02.11.00 and up.

• EPIR3 v1.07.00 and up.

Power supply

230VAC, 50Hz,

protecion class I

Rated load current

12,5A (for resisive

load – 2,8kW)

Power consumpion Up to 1W

Electrical outlet

Type E (EWM1-E)/

Type F (EWFM1-F)/

Type G (EWM1-G)

Wireless band ISM868

Wireless commu-

nicaion range

Up to 30m (98.43t) in

premises; up to 150m

(492.13t) in open areas

Range of operaing

temperatures

-20...+45°C (-4... +113°F)

Circuit thermal

protecion

Below -35°C (-31°F);

above +90°C (+194°F)

Humidity

0-70% RH @ 0...

+40°C (0-70% RH

@ +32... +104°F)

Dimensions

95x53x71mm

(3.74x2.09x2.80in)

Compaible with

alarm systems

ELDES Wireless

EN 11

Limited Liability

The buyer must agree that the system will reduce the risk of

ire, thet, burglary or other dangers but does not guarantee

against such events.“ELDES UAB” will not take any respon-

sibility regarding personal or property or revenue loss while

using the system. “ELDES UAB” liability according to local laws

does not exceed value of the purchased system. “ELDES UAB”

is not ailiated with any of the Internet providers therefore is

not responsible for the quality of Internet service.

Manufacturer Warranty

This device carries a 24-month warranty by the manufac-

turer “ELDES UAB”. Warranty period starts from the day the

system has been purchased by the end user. The warranty is

valid only if the system has been used as intended, following all

guidelines listed in the manual and within speciied operaing

condiions. Receipt must be kept as a proof of purchase date.

The warranty is voided if the system has been exposed to me-

chanical impact, chemicals, high humidity, luids, corrosive and

hazardous environment or other force majeure factors.

Safety Instrucions

Please read and follow these safety guidelines to safeguard

yourself and others:

• DO NOT use the device where it can interfere with other

devices - such as medical devices

• DO NOT use the device in hazardous environments

• DO NOT expose the device to high humidity, chemical en-

vironments or mechanical impact

• DO NOT atempt to repair the device yourself - any repairs

must be carried out by fully qualiied personnel only

• NEVER atempt to dismantle the device.

• DO NOT connect the device to the supply voltage if any

damage is suspected. Life-threatening danger!

• DO NOT touch the device with damp or wet hands!

12 EN

The EWM1 is designed in accordance with

protecion class I. The power source that

may be used is the household electrical

outlet (230VAC, 50Hz) with the protecive

earth conductor of the public power supply

system.

The device is not meant for outdoor use,

i.e. you should use it inside a building. Pro-

tect the device against cold, heat and keep

away from direct sunlight while in storage

or operaion.

The device must be kept out of the reach

of children. Take paricular care when chil-

dren are around!

Never install or carry out maintenance

during stormy weather. The electric sock-

et that powers the device must be easily

accessible.

To switch the system of, unplug the de-

vice from the household electrical outlet.

A blown fuse cannot be replaced by the

user. The replacement fuse has to be of the

kind indicated by the manufacturer (fuse F1

model – SIBA 160000.0,25 0.25A 250V).

EN 13

It is not allowed to copy and distribute infor-

maion in this document or pass to a third

party without advanced writen authorizaion

by “ELDES UAB”. “ELDES UAB” reserves the

right to update or modify this document and/

or related products without a warning. Hereby,

“ELDES UAB” declares that the wireless power

socket EWM1 is in compliance with the essenial

requirements and other relevant provisions of

Direcive 1999/5/EC. The declaraion of con-

formity may be consulted at www.eldes.lt

The WEEE (Waste Electrical and Electronic

Equipment) marking on this product (see right)

or its documentaion indicates that the product

must not be disposed of together with house-

hold waste. To prevent possible harm to human

health and/or the environment, the product

must be disposed on in an approved and envi-

ronmentally safe recycling process. For further

informaion on how to dispose of this product

correctly, contact the system supplier, or the

local authority responsible for waste disposal

in your area.

Page is loading ...

Made in the European Union

www.eldes.lt

Eldes EWM1 User guide

Eldes EWM1 User guide

in other languages

Related papers

Other documents