2. Kichler Lighting
  3. 15474OZ

Kichler Lighting 15474OZ User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 15474OZ User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This fixture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specifications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
1) WARNING: This fixture is not to be installed within 10 feet (3M) of a pool,
spa or fountain.
2) This fixture is to be used only with a power unit (transformer) rated a
maximum of 300 W (25 AMPS) 15 volts.
3) The #18 ga. fixture wire is not intended for direct burial.
4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath
the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
•8GAwirecanbepurchasedinlengthof250’(76M),15503-BK.
•10GAwirecanbepurchasedinlengthof250’(76M),15504-BK.
•12GAwirecanbepurchasedinlengthsof100’(30M),15501-BK;250’
(76M),15502-BK;500’(152M),15505-BK;and1000’(304M),15506-BK.
5) Fixture shall not use a tungsten halogen lamp unless the fixture is marked
for use with such lamps.
6) Wiring connections must be made with approved/listed wire connection
device(s)suitablefortheapplication.Donotexceedmanufacturers’wiring
combination specifications for size and quantity of conductors.
4” X 4” POST APPLICATION ASSEMBLY INSTRUCTIONS - SEE FIG. 2
1) Remove thumbscrews from bottom of fixture head and remove post
adapter from inside fixture head.
2) Place post adapter on top of post allowing equal distances on all sides.
3) Mark position of mounting holes on top of post and remove post adapter.
4) Drill pilot holes in top of post in locations marked in step 3.
5) Drill hole for wire way.
6) Using provided wood screws assemble post adapter to top of post.
7) Installprovidedbulbtosocketinsidexturebody
8) Re-assemblextureheadtopostadapter..
9) TURN OFF POWER.
10) Make wire connections using supplied Quic Disc
™
following instructions
below, or using other approved wiring connection method (not supplied.)
RAIL APPLICATION ASSEMBLY INSTRUCTIONS - SEE FIG. 1
1) Place rail adapter on to top of railing with mounting holes on center of railing.
2) Mark position of mounting holes and wire way hole on top of railing and
remove rail adapter.
3) Drill pilot holes in top of railing in locations marked in step 2.
4) Drill hole suitable for wire to pass through in position marked in step 2.
5) Using provided wood screws assemble rail adapter to top of railing.
6) Remove thumbscrews from bottom of fixture head and remove post
adapter from inside fixture head.
7) Passwirethroughholeandplacepostadapterontopofrailadapterand
secure in place using provided sheet metal screws.
8) Install provided bulb to socket.
9) Re-assemblextureheadtopostadapter.
10) TURN OFF POWER.
11) Make wire connections using supplied Quic Disc
™
following instructions
below, or using other approved wiring connection method (not supplied.)
6” X 6” POST APPLICATION ASSEMBLY INSTRUCTIONS - SEE. FIG. 3
1) Place post cap on top of post.
2) Mark position of mounting holes on top of post and remove post cap.
3) Drill pilot holes in top of post in locations marked in step 2.
4) Drill hole for wireway.
5) Replace post cap on top of post.
6) Place rail adapter on top of post cap aligning mounting holes of cap and
adapter.
7) Usingprovidedwoodscrewsassemblerailadapterandpostcaptotopof
post.
8) Remove thumbscrews from bottom of fixture head and remove post
adapter from inside fixture head.
9) Pass wire through hole and place post adapter on top of rail adapter and
secure in place using provided sheet metal screws.
10) Install provided bulb to socket.
11)Re-assemblextureheadtopostadapter.
WARRANTY
WE WARRANT THE LANDSCAPE PRODUCTS FEATURED IN OUR LANDSCAPE LIGHTING CATALOG (WITH THE EXCEPTION OF LIGHT BULBS) FOR FIVE YEARS AGAINST DEFECTS IN
MATERIALS AND WORKMANSHIP IF IT WAS PROPERLY INSTALLED AND FAILED UNDER NORMAL OPERATING CONDITIONS, PROVIDED IT IS RETURNED TO THE POINT OF PURCHASE,
WHERE IT WILL BE REPAIRED OR, AS IT MAY BE DETERMINED, TO REPLACE THE LANDSCAPE PRODUCT OR PARTS USED ON THAT PRODUCT.
DateIssued:5/7/10 IS-15474-US
Quic Disc
™
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
The Quic Disc
™
connector is designed to install one fixture and accommodates one18GAxturewireandone10GAorone12GAsupplywire.
Placethe10gaugesupplywireacrosstheareamarked10GAonQuicDisc
™
orplacethe12gaugesupplywireacrosstheareamarked12GA
on Quic Disc
™
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
™
. After the wires are in place, connecta the top of the Quic
Disc
™
to the base with supplied screw, making sure that the wires remain flat in the bottom portion of the Quic Disc
™
, and the screw is tightened
all the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
™
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
FIG. 1
FIG. 2
FIG. 3
RAILING
CARRIL
BULB
BOMBILLA
RAIL ADAPTER
ADAPTADOR
DEL RIEL
POST ADAPTER
ADAPTADOR DEL
POSTE
THUMBSCREW
TORNILLO DE
APRIETE
FIXTURE HEAD
CABEZA DEL ARTEFACTO
4” SQ. POST
POSTE
CUADRADO DE 4”
6” SQ. POST
POSTE
CUADRADO DE 6”
SHEET METAL SCREW
TORNILLO PARA CHAPAS
WOOD SCREW
TORNILLO PARA MADERA
POST CAP
TAPA DEL
POSTE
Page is loading ...
/