Kenwood MC-60A User manual

Kenwood
Brand
Kenwood
Model
MC-60A
Type
User manual

This manual is also suitable for

Kenwood MC-60A desktop microphone is designed to provide excellent performance when used with any Kenwood transceiver. It features a zinc die-cast base for stability, a feather-touch PTT switch, an impedance selector switch, and a built-in preamplifier. The microphone can be used with or without the base stand, and it includes an UP/DOWN switch for selecting the transceiver's operating frequency. The MC-60A is constructed of precision parts and is sensitive to shock and vibration, so it should be treated with care.

Kenwood MC-60A desktop microphone is designed to provide excellent performance when used with any Kenwood transceiver. It features a zinc die-cast base for stability, a feather-touch PTT switch, an impedance selector switch, and a built-in preamplifier. The microphone can be used with or without the base stand, and it includes an UP/DOWN switch for selecting the transceiver's operating frequency. The MC-60A is constructed of precision parts and is sensitive to shock and vibration, so it should be treated with care.

DESKTOP MICROPHONE
INSTRUCTION MANUAL
Thank you for purchasing this MC-6OA desktop microphone.
This
rrricrophone has been designed expressly for use with
your amateur communications system. It provides excellent
performance when used
with any
KENWOOD
transceiver,
thereby upgrading your existing system.
The zinc die-cast base offers improved stability and is
complete with a feather-touch
PTT
switch, an impedance
selector switch, and a built-in preamplifier.
The microphone is constructed of precision parts. Do not
open the microphone as it may result in serious damage.
The microphone is sensitive to shock and vibration. Treat
it with care.
50W500
IMP. Switch rON/OFF Switch
WIIC AMP INIOUT
(Underside)
UP/DOWN Switch
Connect to
Radio Mic
Terminal
LOCK Switch
-
PTT Switch
KENWOOD
KENWOOD CORPORAl'ION
0
B62-1643-00
(M)
090807060504030201 00
Installing the Batteries
1
Remove the
4
screws from the base of the
rrricrophone and gently separate the base from the
rr~icrophone unit.
2 Insert two AA batteries into the battery compartment,
being sure to match the polarities with those marked in
the compartment.
3
Replace the
4
screws.
Note:
If
your transceiver supplies power through its microphone
connector, you do not need to install the two
AA
batteries.
111
Batteries
"AA"
hlkaline
(Not Ni-Cd)
Il
Connecting to the Transceiver
1 Slide the microphone into the bracket on the base
stand.
2 Connect the non-coiled cable ,from the rear of the base
stand to the rear of the microphone.
3
Connect the retractable cable from the base to the
transceiver's microphone jack.
First reniove the base of the microphone, then slide .the
switch to tlie
IN
position to turn the preamplifier ON.
Transmitting
With the switch in the
OUT
position, the preamplifier is
bypassed and the batteries are disconnected. To conserve
To transmit, press and hold the
PlT
switch, then speak
battery power, turn the preamplifier
OFF
when it is not in
into the microphone.
use.
The
MC-6OA
is equipped with a
LOCK
switch which allows
With the switch in the
IN
position, the preamplifier is
ON
and
you to lock the
PlT switch down without continuously
the microphone can be used with
VOX
operated equipment.
pressing it. While pressing the
PlT switch, press the
LOCK
switchtokeepthePlTswitclilocked.ToreleasetheL0CK
.
Oneral:ionWi3thouttheBaseStand
switch, sim~lv Dress it aaain.
I
.
.r.
-
You can use the microphone without the base stand by
When
you
have
finished
release
the
PIT
switch
connecting the microphone to the retractable cable, then
to receive.
directly to the transceiver. Doing so means you can no
Impedance Selection
You can set the microphone impedance to
500
i2
or
50
ki2. Slide the
50W500
IMP.
switch on the top of the
microphone to your desired position.
Microphone Preamplifier
You can use this microphone with any
KENWOOD
transceiver. It has been designed especially for FM and
SSB mobile transceivers. You can control the preamplifier
using the
MIC AMP INIOUT
switch on the inside of the
base of the transceiver.
longer use the preamplifier, which is built
info the base
stand.
With a direct connection to the transceiver, you must use
the
ONIOFF
switch located on the top of the microphone
when you transmit. Slide the switch to the ON position to
transmit, and to the OFF position to receive.
UPIDOWN Switcli
Use the
UPIDOWN
switch to select the transceiver's
operating frequency. Refer to your transceiver instruction
manual for further details on how to select an operating
frequency.
Type:
Cornmunical:ion type dynamic microphone with PlT circuit.
Element:
Impedance:
Sensitivity:
Microphone
Preamp out
Preamp in
Frequency response:
Microphone or preamp off
Preamp on
Recorr~mended operating distance
from microphone:
Moving coil type, unidirectional
Dual impedance
(1 000
Hz)
50
ki2
f30%, 500
i2
f
30%
slide switch selectable
(0
dB
=
1
V/
pBAR,
1000
Hz)
150
HZ
-
10
kHz
(-6
dB)
200
Hz
-
7
kHz
(-6
dB)
10
cm
(4
inches) minimum
MIC
unit
connection
Impedance
50k-500
p
(White)
1
(Green)
P.
T. T
MIC
stand
connection
MIC
AMP
IN -OUT
MIC cable connection
PG-4C
(Black)
(Shield)
A
(Yellow)
  • Page 1 1
  • Page 2 2

Kenwood MC-60A User manual

Kenwood
Brand
Kenwood
Model
MC-60A
Type
User manual
This manual is also suitable for

Kenwood MC-60A desktop microphone is designed to provide excellent performance when used with any Kenwood transceiver. It features a zinc die-cast base for stability, a feather-touch PTT switch, an impedance selector switch, and a built-in preamplifier. The microphone can be used with or without the base stand, and it includes an UP/DOWN switch for selecting the transceiver's operating frequency. The MC-60A is constructed of precision parts and is sensitive to shock and vibration, so it should be treated with care.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents