DeWalt DW274K User manual

Page is loading ...

B

Copyright

DeWALT

Dansk (oversat fra original brugsvejledning) 4

Deutsch (übersetzt von den originalanweisungen) 10

English (original instructions) 17

Español (traducido de las instrucciones originales) 23

Français (traduction de la notice d’instructions originale) 30

Italiano (tradotto dalle istruzioni originali) 36

Nederlands (vertaald vanuit de originele instructies) 42

Norsk (oversatt fra de originale instruksjonene) 48

Português (traduzido das instruções originais) 54

Suomi (käännetty alkuperäisestä käyttöohjeesta) 61

Svenska (översatt från de ursprungliga instruktionerna) 67

Türkçe (orijinal talimatlardan çevrilmiştir) 73

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 79

Page is loading ...

17

ENGLISH

Fuses:

Europe 230V tools 10 Amperes. mains

U.K. & Ireland 230V tools 13 Amperes. in plugs

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

The vibration emission level given in this information sheet has

been measured in accordance with a standardised test given in

EN60745 and may be used to compare one tool with another. It

may be used for a preliminary assessment ofexposure.



WARNING: The declared vibration emission level

represents the main applications of the tool. However if

the tool is used for different applications, with different

accessories or poorly maintained, the vibration emission

may differ. This may significantly increase the exposure

level over the total workingperiod.

An estimation of the level of exposure to vibration should

also take into account the times when the tool is switched

off or when it is running but not actually doing the job.

This may significantly reduce the exposure level over the

total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of workpatterns.

English (original instructions)

DRYWALL SCREWDRIVER DW263/DW264/DW268/DW269/

DW274/DW274KN/DW275/DW275KN

Congratulations!

You have chosen a

DeWALT

tool. Years of experience, thorough product development and innovation make

DeWALT

one of the

most reliable partners for professional power toolusers.

Technical Data

DW263 DW264 DW268 DW269 DW274 /

DW274KN

DW275 /

DW275KN

Voltage V

AC

230 230 230 230 230 230

UK & Ireland V

AC

230/115 230 230 230 230/115 230

Type 4/5 5 5 5 3/5 5

Power output W 540 540 540 540 540 540

No load speed min

-1

0–2,500 0–2,000 0–2,500 0–1,000 0–4,000 0–5,300

Bit holder 1/4" hex 1/4" hex 1/4" hex 1/4" hex 1/4" hex 1/4" hex

Clutching method depth sensitive depth sensitive Versa Clutch® Versa Clutch® depth / silent

sensitive

depth / silent

sensitive

Weight kg 1.4 1.4 1.4 1.4 1.4 1.4

Noise values and vibration values (triax vector sum) according to EN60745-2-2:

L

PA

(emission sound pressure

level)

dB(A)

87 80 85 84 87 85

L

WA

(sound power level)

dB(A)

94 89 92 91 92 92

K (uncertainty for the given

sound level)

dB(A)

3,5 2,9 3,8 4,0 5,8 3,5

Screwdriving without impact

Vibration emission value a

h

= m/s

2

< 2,5 < 2,5 < 2,5 < 2,5 < 2,5 < 2,5

Uncertainty K = m/s

2

1,5 1,5 1,5 1,5 1,5 1,5

18

ENGLISH



Denotes risk of electricshock.



Denotes risk offire.

EC-Declaration of Conformity

Machinery Directive

Drywall Screwdriver

DW263/DW264/DW268/DW269/DW274/

DW274KN/ DW275/DW275KN

DeWALT

declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-2:2010.

These products also comply with Directive 2004/108/EC (until

19.04.2016), 2014/30/EU (from 20.04.2016) and 2011/65/EU.

For more information, please contact

DeWALT

at the following

address or refer to the back of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf of

DeWALT

.

Markus Rompel

Director Engineering

DeWALT

, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

15.10.2016

WARNING: To reduce the risk of injury, read the

instruction manual.

General Power Tool Safety Warnings



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

19

ENGLISH

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

4) Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

5) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

Additional Specific Safety Rules for

Screwdrivers

• Hold power tool by insulated gripping surface, when

performing an operation where the fastener may

contact hidden wiring or its own cord (bolt). Fasteners

contacting a “live” wire may make exposed metal parts of the

power “live” and could give the operator an electric shock.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA or less.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment of hearing.

• Risk of personal injury due flying particles.

• Risk of burns due to accessories becoming hot during

operation.

• Risk of personal injury due to prolonged use.

• Risk of squeezing fingers when changing the accessory.

• Health hazards caused by breathing dust developed when

working in concrete and/or masonry.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Date Code Position (Fig. A1)

The date code

13

, which also includes the year of manufacture,

is printed into thehousing.

Example:

2016 XX XX

Year of Manufacture

Package Contents

The package contains:

1 Pistol grip screwdriver DW263/DW264

or

1 Universal screwdriver DW268/DW269

or

1 Drywall screwdriver DW274/DW274KN/DW275/DW275KN

1 Kitbox (K-models only)

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Description (Fig. A1, A2)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1

Variable speed switch

2

Lock-on button

3

Forward/reverse slider

4

Depth adjustment collar (DW263/DW264/DW274/

DW274KN/DW275/DW275KN)

Versa Clutch® (DW268/DW269)

5

Depth locator (DW263/DW264/DW274/DW274KN/DW275/

DW275KN)

6

Belt clip

7

Ball retainer (DW268/DW269)

Intended Use

Your DW263/DW264 screwdriver has been designed for

professional screwdriving applications and for use as a nutsetter.

Your DW268/DW269 universal screwdriver has been designed

for professional screwdriving applications.

Your DW274/DW274KN/DW275/DW275KN drywall screwdriver

has been designed for driving drywall fasteners through drywall

board into timber or metal framing studs.

20

ENGLISH

Your DW274KN/DW275KN features a silent clutch function.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

These screwdrivers are professional power tools.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

without supervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Dead Spindle Drive Clutch

This screwdriver is equipped with a dead spindle feature; the

spindle does not turn until the fastener is pressed into the

workpiece. This enables fasteners to be placed onto the drive

accessory of a running screwdriver.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the power supply corresponds to the voltage

on the rating plate.

Your

DeWALT

tool is double insulated in accordance

with EN60745; therefore no earth wire is required.



WARNING: 115 V units have to be operated via a fail-safe

isolating transformer with an earth screen between the

primary and secondary winding.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DeWALT

serviceorganisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.



WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 13A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1.5 mm

2

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

Fitting and Removing 1/4" Hex Drive

Accessories

Your

DeWALT

screwdriver has a 1/4" hexagonal drive system.

The drive accessory is retained in the holder by a ball and a

spring which engages in a groove in the accessory shank.

DW263/DW264/DW274/DW274KN/

DW275/DW275KN (Fig. B)

1. Remove the collar

4

by pulling it forward.

2. Select the required accessory (both models) and matching

depth locator

5

when using a nutsetter (DW263/DW264).

3. To insert the accessory

12

, e.g., a bit holder or nutsetter,

push it into the holder

8

until it snaps in place. Tap it lightly

if required.

4. To remove the accessory, pull it out of the holder using a

pair of pliers.

5. Reinstall the collar

4

by aligning the ribs

9

on the inside of

the collar

4

with the grooves

10

in the clutch housing and

snap the collar in place.

DW268/DW269 (Fig. A2)

1. Pull the ball retainer

7

to the front and hold it.

2. Insert the accessory.

3. Release the ball Retainer.

Replacing the bit tip (Fig. B)

Simply pull out the bit tip

11

. A pair of pliers may be required.

Driving Depth (Fig. C)

DW263/DW264/DW274/DW274KN/

DW275/DW275KN

The depth sensitive feature offers the following advantages:

• The selected driving depth is repeatable for structural

integrity.

• Screws with sealing washers are driven correctly so that no

leaks occur.

Setting the Driving depth

The driving depth is determined by the position of the depth

locator

5

in relation to the bit or socket.The symbols on the

collar

4

indicate how to set the driving depth.

• Turn the collar

4

clockwise to increase the driving depth.

• Turn the collar

4

counterclockwise to decrease the driving

depth.

Versa Clutch® Units

DW268/DW269 (Fig. A2)

External adjustment of all Versa Clutch® units for a wide range of

fastener sizes is fast and easy, as follows:

21

ENGLISH

1. Pull forward, then rotate collar in increase direction

(stamped on adjustment collar) to increase the amount of

clutch engagement and torque output.

2. Maximum rotation of the collar in the increase direction

results in full clutch engagement and maximum torque

output and fastener capacity. Collar and adjustable stop will

not screw off clutch housing.

3. Test drive a fastener into a scrap piece to check proper

fastener seating. It is normal after a period of use to require

a slightly different collar setting due to wear on the clutch

faces.

NOTE: With Versa Clutch®, the operator has the ability to

“override” clutch ratchet if a fastener hits a wood knot, variable

hardness in steel work pieces or incorrect pilot holes. Increased

operator pressure will usually cause the clutches to pick-up

and continue to seat the fastener. Further, a quick twist of the

collar will change the clutch setting to overcome most driving

difficulties and will provide for immediate change in torque

output giving the operator the option to drive a wide range of

fastener sizes.

Using a Nutsetter (Fig. C)

DW263/DW264

1. For screws with sealing washers, turn the collar

4

until

the end of the nutsetter is flush with the end of the depth

locator.

If required, turn the collar until the nutsetter is recessed

approximately 2 mm into the depth locator.

NOTE: ALWAYS refer to the screw manufacturer’s

specifications for the proper sealing washer settings in

different applications.

2. Drive a screw into a scrap piece and check the distance

between the washer and the material.

3. Turn the collar

4

counterclockwise or clockwise to decrease

or increase the driving depth as required.

4. Drive another screw and readjust the collar

4

until the

desired setting is achieved.

Depth Locator (Fig. D)

DW263/DW264

This model is supplied with two depth locators

5

to

accommodate different bits, holders, sockets and adaptors.

To Change Depth Locators

1. Pull the collar

4

assembly off the tool.

2. Hold the depth locator

5

and unscrew the collar

4

.

3. Replace the depth locator

5

.

4. To reassemble, proceed in reverse order.

Forward/Reverse Switch (Fig. E)



WARNING: Always wait until the motor has come to

a complete standstill before changing the direction of

rotation.

Select the forward or reverse rotation by moving the forward/

reverse switch

3

in the direction indicated by the arrows.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

Proper Hand Position (Fig. F)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main handle

14

, as shown.

For best results, hold the screwdriver with the hand directly in

line with the fastener and press the variable speed switch with

the last one or two fingers of the hand, as shown. This reduces

the chance of the screw slipping from the drive accessory when

pressure is applied.

Screwdriving or Nutsetting (Fig. A1)

1. Select the appropriate bit for the screw (or nut) to be driven.

2. Select forward or reverse rotation as described above.

DW263: For nutsetting, always use the correct depth

locator

5

.

3. To run the tool, press the variable speed switch

1

. The

pressure exerted on the variable speed switch determines

the tool speed.

NOTE: If necessary, press the lock-on button

2

for

continuous operation and release the variable speed switch.

The lock-on button only works in full speed, forward and

reverse rotation.

To stop the tool in continuous operation, press the switch

briefly and release it.



WARNING: ALWAYS turn the tool off when work is

finished and before unplugging.

4. To drive the screw, place it on the bit or into the socket,

press the variable speed switch and push the screw into the

workpiece with a smooth, continuous motion. When the

screw is seated, a buzzing sound will come from the front of

the tool to indicate that the clutch has disengaged.

5. To stop the tool, release the switch.

MAINTENANCE

Your

DeWALT

power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.

22

ENGLISH



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

Lubrication

Your power tool requires no additionallubrication.

Cleaning (Fig. A1)



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing this procedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into a liquid.

DW274/DW274KN

Regularly remove drywall dust from the clutch housing using

compressed air. To do so, remove the depth locator

5

and

collar

4

.

Optional Accessories



WARNING: Since accessories, other than those offered

by

DeWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT

recommended

accessories should be used with thisproduct.

Various types of 1/4" hex bits, holders, sockets and adaptors are

available as an option.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

household waste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Page is loading ...

Belgique et

Luxembourg België

en Luxemburg

DeWALT - Belgium BVBA

Egide Walschaertsstraat 16

2800 Mechelen

Tel: NL 32 15 47 37 63

Tel: FR 32 15 47 37 64

Fax: 32 15 47 37 99

www.dewalt.be

[email protected]

Danmark DeWALT

Roskildevej 22

2620 Albertslund

Tel: 70 20 15 10

Fax: 70 22 49 10

www.dewalt.dk

[email protected]

Deutschland DeWALT

Richard Klinger Str. 11

65510 Idstein

Tel: 06126-21-1

Fax: 06126-21-2770

www.dewalt.de

[email protected]

Ελλάς DeWALT (Ελλάς) Α.Ε.

EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7

& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα

SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος

Τηλ: 00302108981616

Φαξ: 00302108983570

www.dewalt.gr

[email protected]

España DeWALT Ibérica, S.C.A.

Parc de Negocios “Mas Blau”

Edificio Muntadas, c/Bergadá, 1, Of. A6

08820 El Prat de Llobregat (Barcelona)

Tel: 934 797 400

Fax: 934 797 419

www.dewalt.es

[email protected]

France DeWALT

5, allée des Hêtres

BP 30084, 69579 Limonest Cedex

Tel: 04 72 20 39 20

Fax: 04 72 20 39 00

www.dewalt.fr

[email protected]

Schweiz

Suisse

Svizzera

DeWALT

In der Luberzen 42

8902 Urdorf

Tel: 044 - 755 60 70

Fax: 044 - 730 70 67

www.dewalt.ch

[email protected]

Ireland DeWALT

Calpe House Rock Hill

Black Rock, Co. Dublin

Tel: 00353-2781800

Fax: 00353-2781811

www.dewalt.ie

Italia DeWALT

via Energypark

20871 Vimercate (MB), IT

Tel: 800-014353

39 039 9590200

Fax: 39 039 9590313

www.dewalt.it

Nederlands DeWALT Netherlands BV

Holtum Noordweg 35

6121 RE BORN, Postbus 83, 6120 AB BORN

Tel: 31 164 283 063

Fax: 31 164 283 200

www.dewalt.nl

Norge DeWALT

Postboks 4613, Nydalen

0405 Oslo

Tel: 45 25 13 00

Fax: 45 25 08 00

www.dewalt.no

[email protected]

Österreich DeWALT

Werkzeug Vertriebsges m.b.H

Oberlaaerstrasse 248, A-1230 Wien

Tel: 01 - 66116 - 0

Fax: 01 - 66116 - 614

www.dewalt.at

[email protected]

Portugal DeWALT Limited, SARL

Centro de Escritórios de Sintra Avenida

Almirante Gago Coutinho, 132/134, Edifício 14

2710-418 Sintra

Tel: 214 66 75 00

Fax: 214 66 75 80

www.dewalt.pt

[email protected]

Suomi DeWALT

PL 47

00521 Helsinki

Puh: 010 400 4333

Faksi: 0800 411 340

www.dewalt.fi

[email protected]

Sverige DeWALT

Box 94

431 22 Mölndal

Tel: 031 68 61 60

Fax: 031 68 60 08

www.dewalt.se

[email protected]

Türkiye KALE Hırdavat ve Makina A.Ş.

Defterdar Mah. Savaklar Cad. No:15

Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE

Tel: 0212 533 52 55

Faks: 0212 533 10 05

www.dewalt.com.tr

United

Kingdom

DeWALT, 210 Bath Road;

Slough, Berks SL1 3YD

Tel: 01753-567055

Fax: 01753-572112

www.dewalt.co.uk

[email protected]

Australia DeWALT

82 Taryn Drive, Epping

VIC 3076 Australia

Tel: Aust 1800 338 002

Tel: NZ 0800 339 258

www.dewalt.com.au

www.dewalt.co.nz

Middle East Africa DeWALT

P.O. Box - 17164,

Jebel Ali Free Zone (South), Dubai, UAE

Tel: 971 4 812 7400

Fax: 971 4 2822765

www.dewalt.ae

[email protected]

N467543 02/16

DeWalt DW274K User manual

This manual is also suitable for

DeWalt DW274K User manual

in other languages

Related papers

Other documents