Python 4806P Owner's manual

Category
Remote starters
Type
Owner's manual

This manual is also suitable for

MODEL
4806P
SECURITY FOR THE BEST
®
OWNER’S GUIDE
iii
© 2016 Directed. All rights reserved.
Congratulations
Congratulations on the purchase of your state-of-the-art remote start
and keyless entry system. Reading this Owner’s Guide prior to using
your system will help maximize the use of your system and its many
features. For any additional questions please contact your authorized
Directed dealer or contact Directed at 1-800-753-0600. (U.S. only)
or 1-800-361-7271 (Canada only). Additional support is also avail-
able at: http://support.directed.com
Important information
Government Regulations and Safety information
Read the Government Regulations and Warning! Safety
First sections of this manual prior to operating this system.
Warning! Failure to heed this information can result in
death, personal injury or property damage and may also
result in the illegal use of the system beyond its intended
purpose.
Your Warranty
Your system comes with a warranty. The warranty terms are detailed
at the end of this guide. Make sure that you receive the proof of
purchase from your dealer, indicating the product was installed by an
authorized Directed dealer.
G4806 2016-02
iv
© 2016 Directed. All rights reserved.
Replacement remote controls
Please see your authorized dealer or visit us at www.directedstore.
com to order additional remote controls. Remote control RPNs (Re-
placement Part Numbers) are found on the back of the device.
Contents
Congratulations ................................................................................................. iii
Important information ........................................................................................ iii
Government Regulations and Safety information ..................................... iii
Your Warranty .....................................................................................iii
Replacement remote controls ................................................................. iv
Getting Started .................................................................................................... 3
Keys to using this manual ...................................................................... 3
Remote Control Information .................................................................................. 4
Control Center .................................................................................................... 5
Using your System ............................................................................................... 6
Commanding the system ....................................................................... 6
Performing Commands ......................................................................... 6
Remote Control Command table ............................................................ 7
Fault Condition alerts ........................................................................... 7
Basic Commands (Direct Access) .......................................................................... 8
Lock ................................................................................................... 8
Unlock ................................................................................................ 8
Remote Start ........................................................................................ 8
AUX/Trunk .......................................................................................... 9
Advanced Commands: (Level 1) ......................................................................... 10
Silent Lock......................................................................................... 10
Runtime Reset .................................................................................... 10
AUX 1 .............................................................................................. 11
Temperature Request .......................................................................... 11
Advanced Commands: (Level 2) ......................................................................... 12
Remote Valet .................................................................................... 12
Timer Start ........................................................................................ 12
AUX 2 .............................................................................................. 12
Advanced Commands: (Level 3) ......................................................................... 14
Car finder ......................................................................................... 14
Smart Start ........................................................................................ 14
AUX 3 .............................................................................................. 14
Runtime Remaining ............................................................................ 15
Advanced Commands: (Level 4) ......................................................................... 16
Defogger .......................................................................................... 16
AUX 4 .............................................................................................. 16
Remote Control Configuration ............................................................................ 17
Remote Programming ......................................................................... 17
Remote Features ................................................................................ 17
Keypad Lock ..................................................................................... 18
Page Mode ....................................................................................... 19
Car 2 ............................................................................................... 19
Remote Beep ..................................................................................... 19
Remote Pairing Mode ......................................................................... 20
Emergency Override ......................................................................................... 21
Remote Start Features ........................................................................................ 22
Key Takeover..................................................................................... 22
Remote Start Safe-lock ...................................................................... 22
Disabling Remote Start ..................................................................... 22
Advanced Start ................................................................................. 22
Temperature Reporting ........................................................................ 24
Remote Start Time-out Alert .................................................................. 24
Pit Stop Mode ................................................................................... 24
Manual Transmission Start (MTS mode) ................................................ 25
Turbo Timer Mode .............................................................................. 26
Remote Start Faults ............................................................................. 26
Remote and System Operations .......................................................................... 28
Passive Locking ................................................................................. 28
Auto Re-locking ................................................................................ 28
Valet Mode ....................................................................................... 29
Power Save ....................................................................................... 29
Rapid Resume ................................................................................... 29
Automatic Remote Updates ................................................................. 29
Car Select ......................................................................................... 30
Out of Range .................................................................................... 30
No Remote Output ............................................................................. 30
System Expansion Options ................................................................................. 31
Battery Information ............................................................................................ 33
Low Battery ....................................................................................... 33
Battery Life ........................................................................................ 33
Battery Replacement ........................................................................... 34
Battery Disposal ................................................................................ 34
Glossary of Terms .............................................................................................. 35
Patent Information ............................................................................................. 35
Government Regulations .................................................................................... 36
Warning! Safety First ......................................................................................... 38
3
© 2016 Directed. All rights reserved.
Getting Started
Keys to using this manual
Specific actions (in bold type) and style conventions are used consis-
tently throughout this manual, they are as follows:
Press: implies pushing in and releasing a button.
Hold: is used after Press actions when a button needs to be held
in position for an extended period of time, typically several sec-
onds.
Italicized words denote section/sub headings in this guide and
can be located through the table of contents.
An asterisk (*) when used after a word or phrase denotes that
additional details can be found in related sections usually noted
at the bottom of the page or end of the section.
Confirmation LED’s are identified by the command/function but-
ton they are associated with.
4
© 2016 Directed. All rights reserved.
Remote Control Information
Feature Description
Internal Antenna Used for transmitting and receiving*information.
Command buttons (4)
A U X
A U X
A U X
AUX
Used to perform Locking, Unlocking, Auxiliary channel and
Remote Start commands.
Function button
A U X
Used to access function levels for commands, configura-
tion menus for programming, Car Selection, and to request
reports.
Confirmation LED’s Each button has an associated LED next to it that are active
during related operations. These LEDs are labeled respec-
tively as: Lock LED, Unlock LED, Remote Start LED, and AUX
LED.
*2-way communication is only applicable to the Responder LE
remote control.
5
© 2016 Directed. All rights reserved.
Control Center
Control CenterLED Button
The Control Center, typically located on the upper part of the front
windshield, sends and receives commands or messages to and from
your system. It consists of:
The In-vehicle system antenna.
The Status LED, as a visual indicator of the system’s status.
The Control button, for placing the system into Valet Mode* and
to perform the Emergency Override** operation.
* See “Remote and System Operations” on page 28.
**
See “Emergency Override” on page 21
6
© 2016 Directed. All rights reserved.
Using your System
Commanding the system
Commands, Basic or Advanced, are used to activate system features
and are performed by pressing one of the Command buttons. Basic
commands control the most often used keyless entry and remote start
features while Advanced commands control more specialized fea-
tures.
Confirmations for Basic or Advanced commands are indicated
by horn honks* and parking light flashes. A description of each fea-
ture confirmation is found in the following Basic command and Ad-
vanced command sections.
Performing Commands
Perform Basic commands by pressing a Command button.
Perform Advanced Commands by first accessing Levels 1-4 using the
AUX
button and then by pressing a Command button while within a
level.
Advanced command example: Silent Lock
1. Press the
AUX
button once to access Function Level 1.
2. Press the
AUX
AUX
button to perform the Silent Lock command.
3. The system will lock the doors and flash the parking lights,
without horn honks.*
* The optional Horn Honk feature must be connected
7
© 2016 Directed. All rights reserved.
Remote Control Command table
Basic
Commands
Advanced Commands
Button
Level
Direct Access
A U X
x 1
A U X
x 2
A U X
x 3
A U X
x 4
A U X
Lock Silent Lock
A U X
Unlock Silent Unlock Remote Valet Car Finder
A U X
Remote Start Reset Runtime Timer Start Smart Start Defogger
AUX
AUX/Trunk AUX 1 AUX 2 AUX 3 AUX 4
A U X
Advance
Level, Change
Car (3 sec.),
Enter program-
ming (8 sec.)
Cabin Temp.
Request
(2- way only)
Lock
Status
(2- way
only)
Runtime
Check
(2- way only)
Fault Condition alerts
If, when performing a command, a condition exists that does not al-
low activation of the remote start feature* a fault tone plays to alert of
the fault condition.
* Remote Start feature not available when the Remote Start status is
incorrect upon receiving the command. (Example: Runtime reset com-
mand received when remote start is off)
Refer to the notes included in the command descriptions that address
these faults or go to Remote Start Faults under the Remote Start Fea-
tures section for more details.
8
© 2016 Directed. All rights reserved.
Basic Commands (Direct Access)
Lock
Press and release
,
Doors lock (if connected). The horn honks once, and the parking lights
flash one-time. Lock LED turns on with one beep.
To Lock and Panic
Press and hold
To lock the system, then activate Panic. For Panic to be effective,the
optional horn honk feature must be connected. Press the
AUX
AUX
or
button to stop Panic output.
Unlock
Press and release
.
The doors unlock (if connected). The horn honks twice and the parking
lights flash. Unlock LED turns on and remote beeps twice.
Remote Start*
Press and release
AUX
AUX
Activates (or if ON, deactivates) the remote starter. The engine turns
on, or the engine turns off accordingly. The parking lights flash. Re-
mote Start LED turns on, and plays tones. If a Remote start configura-
tion issue prevents the engine from starting, the parking lights flash a
Remote Start fault report to identify the fault.
9
© 2016 Directed. All rights reserved.
AUX/Trunk**
Press and hold AUX.
The AUX LED turns on and tones play to confirm. The Trunk opens (if
connected) when this button is pressed for two seconds.
* For Manual transmission vehicles see “Manual Transmission Start
(MTS mode)” on page 25
in the “Remote Start Features” sec-
tion for more details.
**This is an optional feature. See your authorized Directed dealer
for details.
10
© 2016 Directed. All rights reserved.
Advanced Commands: (Level 1)
Press and release the
AUX
button one time first, before pressing one of
the following command buttons.
Silent Lock
Press and release
The doors lock (if connected), without horn honks.* The Lock LED turns
on to confirm.
Silent Unlock
Press and release
Doors unlock (if connected), without horn honks. The parking lights
flash twice. The Unlock LED turns on to confirm.
Runtime Reset
Press and release
AUX
AUX
If more time is needed while remote start is active, runtime reset will
reset the runtime counter to the pre-programmed setting. The confirma-
tion LEDs show the runtime and the Remote Start ON tones play to
confirm runtime reset.
Note
Remote Start must be ON to use this feature.
11
© 2016 Directed. All rights reserved.
AUX 1
Press and release
AUX
Activates (or if ON, deactivates) the AUX 1 output. The AUX LED turns
on and tones play to confirm.
Temperature Request
Press and hold the
AUX
button
Requests the vehicle’s interior temperature, and displays it by illuminat-
ing the confirmation LEDs as indicated in the table below.
LED count Temperature indicated
1 31°F
2 32°F – 56°F
3 57°F – 81°F
4 82°F
Note: Actual temperature may vary with main unit mounting location.
* The optional Horn Honk feature must be connected.
12
© 2016 Directed. All rights reserved.
Advanced Commands: (Level 2)
Press and release the
AUX
button two times first, before pressing one of
the following command buttons.
Remote Valet
Press and release
Enters (or if ON, exits) Valet Mode. The Control Center LED turns on
and off accordingly, and prevents doors from locking passively. The
The Unlock LED and Valet beeps play (one for ON, two for OFF) to
confirm.
Timer Start*
Press and release
AUX
AUX
Activates (or if ON, deactivates) Timer Start. The parking lights flash
quickly four times for ON and slowly four times for OFF. The Remote
Start LED and beeps play (one for ON, two for OFF) to confirm.
Note
System needs to be locked or Timer Start will not start the
engine.
AUX 2
Press and release
AUX
Activates (or if On, deactivates) the AUX 2 output. The AUX LED and
ON tones or OFF tones play to confirm.
13
© 2016 Directed. All rights reserved.
Lock Status
Press and hold the
AUX
button.
The remote will generate an output using the LEDs and beeps/tones
to display the systems Lock Status since its last update message or
command operation. It will report status via confirmation LEDs, beeps,
and tones as described in this section for Lock, Unlock, Valet Mode
and Silent Lock.
*See “Advanced Start” on page 22 for more details.
14
© 2016 Directed. All rights reserved.
Advanced Commands: (Level 3)
Press and release the
AUX
button three times first, before pressing one
of the following command buttons.
Car finder
Press and release
The horn emits one long honk and the parking lights flash for 10 sec-
onds. The parking light flashes stop if locked or unlocked while Car
Finder is in progress. Lock and Unlock cancels the parking light flash.
Smart Start*
Press and release
AUX
AUX
Activates (or if ON, deactivates) Smart Start. The parking lights flash
quickly five times for ON and slowly five times for OFF. The Remote
Start LED and beeps play (one for ON, two for OFF) to confirm.
Note
System needs to be locked or Smart Start will not start the
engine.
AUX 3
Press and release
AUX
Activates (or if On, deactivates) the AUX 3 output. The AUX LED and
ON tones or OFF tones play to confirm. See your authorized Directed
dealer for details.
15
© 2016 Directed. All rights reserved.
Runtime Remaining
Press and hold the
AUX
button
Requests the remaining Remote start runtime and temporarily displays
it in four increments using the Confirmation LED’s.
Example for 12 minute runtime:
Three LEDs: six to nine minutes remaining (50 - 75% of time
selected).
One LED: less than three minutes remaining (<25% of time se-
lected).
Note
Remote Start must be ON to use this feature.
*See “Advanced Start” on page 22 for more details.
16
© 2016 Directed. All rights reserved.
Advanced Commands: (Level 4)
Press and release the
AUX
button four times first, before pressing one of
the following command buttons.
Defogger*
Press and release
AUX
AUX
Activates the vehicle Defogger circuit (if connected) while Remote Start
is activated and the parking lights flash three times. The Remote start
LED and one beep play to confirm. For convenience, the Defogger
circuit will also automatically activate 10 seconds after remote starting
if the temperature is below 55°F.
Note
Remote Start must be active to use this feature.
AUX 4
Press and release
AUX
Activates (or if ON, deactivates) the AUX 4 output. The AUX LED and
ON tones or OFF tones play to confirm.
* This feature must be installed and turned on by an authorized
Directed dealer.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Python 4806P Owner's manual

Category
Remote starters
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI