Power 616 II
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initially start-up.
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions of this manual
1. INTRODUCTION
Thank you for having chosen
Power 616 II
. You will see you acquired a powerful and versatile
device. Unpack your item. Before you initial start-up, please make sure that there is no
damage caused by transportation. Should there be any, consult your dealer and do not use the
device.
2. SAFETY INSTRUCTIONS
This device has left our premises in absolutely perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to follow the
safety instructions and warning notes written in this user manual. Always disconnect from the
mains, when the device is not in use or before cleaning it. Keep away children and amateurs
from the device! There are no serviceable parts inside the device. Maintenance and service
operations are only to be carried out by authorized dealers.
3. FEATURES
Single phase, Three phase power, a suitable hard wire terminals, DMX signals or analog
signals (0-10V) from a dimmer controller, 20A breaker, six channel dimmer with each channel
20 amp circuit breaker, Preheat adjuster maximum 50%----Lengthens dimming capability,
channel dimmer control
4. Operations
DMX-512 connection with the scanner
The wires must not come into contact with each other, otherwise the fixtures will not work at all,
or will not work properly. Only use a stereo shielded cable and 3-pin XLR-plugs and
connectors in order to connect the controller with the fixture or one fixture with another.
Occupation of the XLR-connection:
You can adjust the XLR polarity via the DMX POLARITY selector.
Building a serial DMX-chain:
Connect the DMX-output of the DMX Scan Control with the DMX-input of the nearest projector.
Always connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a
120
.
resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last fixture.
Single phase connection
1. Output: 6 single tap terminals for positive without jumping
2. Ground wires with terminals jumped together
3. All neutral wires with terminals already jumped together
4. Input: All three of these terminals for powering
OUTPUT GROUND NEUTRAL INPUT
Three phase connection
5. 6 single tap terminals for positive without jumping
6. Ground wires with terminals jumped together
7. All neutral wires with terminals jumped together
8. All three of these terminals for powering
OUTPUT GROUND NEUTRAL INPUT
push shift and function button to go running mode. Then use up or down to set up the
value. If the item at DMX mode and the DMX signal is correct, the DMX led will
flash.
You can use ch1-ch6 up or down buttons to direct control channel output in any case.
Running mode: push shift button and up in the meantime you will go Auto running
mode and the display will show A___ AUTO led will light. If you push shift and
down you will go DMX mode.DMX led will light.
Select preheat: push shift and preheat button you can select preheat value
(0-30%).this vale is different in Dmx mode and auto mode.
Select the max: out value: push shift and master to select the max. Out in auto mode
and dmx mode.
Fade time set: push shift and fade time button to set up the fade time. (0-10s) set up
the start DMX address: push shift and address to set up the start address and use up or
down to select.
Select auto pattern: push shift and program button then using up or down to select
auto pattern from 1 to 16.
Select auto speed: push shift and speed button then using up or down to select the
auto speed from 1 to 100. (1 step/10s,10steps/1 s)
5. CLEANING AND MAINTENANCE
Disconnect from mains before starting maintenance operation!
DANGER TO LIFE!
We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened
cloth. Never use alcohol or solvents! There are no serviceable parts inside the device.
Maintenance and service operations are only to be carried out by authorized dealers.
6. TECHNICAL SPECIFICATIONS
Power supply: 220 V AC, 50 Hz ~
Three Phase or Single Phase connections
BREAKER 6 x 20 amp circuit breakers
DMX 512-output: 3-pin XLR-connector
Each channel output up to 10A, total 60A
Dimension; 482mm x 381mm x 89mm
Weight: 8.0kgs
Please note: Any information is subject to change without prior notice.
/