Pulsar PSBC10A12 Operating instructions

Brand: Pulsar

Model: PSBC10A12

Category: Power supply units

Type: Operating instructions

PSU-B-13.8V/S-10A/1/EL-TR-17Ah/MC

PSBC 10A12

v.1.0

Buffer, switch mode power supply unit.

Edition: 1 from 14

December 2010

Supercedes edition: --------------------

Features of the power supply unit:

• 13.8 VDC uninterruptible power supply

• Controlling of battery charging and

maintaining

• Protecting of battery against excessive

discharging (UVP)

• Securing the BAT circuit against short-circuit

and the battery reverse connection

• Selectable charging current

• START function of manual battery actuation

• Checking the status of safety fuses of AUX1,

AUX2 and AUX3 outputs

• LED optical signalisation

• BS output for the signalling loss of the 230V

network

• AW output of power supply unit failure,

tripped by:

• outlet short-circuit (SCP)

• outlet overload (OLP)

• battery disconnection < 10V (UVP)

• failure of DC/DC voltage converter

• Safety equipment:

• SCP short-circuit protection

• OLP overload protection

• OHP overheat protection

• OVP overvoltage protection

• Surge protection

• Against sabotage

CONTENTS:

1. Technical description

1.1. General description

1.2. Block diagram

1.3. Description of elements and power supply connectors

1.4. Technical parameters

2. Installation.

2.1. Requirements

2.2. Installation procedure

3. The power supply operation indication

3.1. Optical indication

3.2. Technical output

4. Service and operation

4.1. Overload or short circuit

4.2. Battery operation

4.3. Maintenance

1. Technical description.

1.1. General description.

The buffer power-supply is used for uninterrupted supply of devices requiring stabilized voltage of 12V DC

(+/-15%). The power-supply provides voltage within the following range: U= 11.0V÷13.8V DC of total current

efficiency equal to 10A. In case of power voltage decay, prompt switching to battery supply occurs.

The power-supply has got a metal casing (RAL 9003 colour) with a space for 17Ah/12V battery. The casing

features a micro-switch indicating door (front) opening and separating from the wall.

Information about additional equipment for PSBC 10A12 power-supply:

Modules of DC/DC

voltage converters

DCDC10 (1,0 A)

DCDC20 (2,0 A)

Protection module

(fuse blocks)

AWZ 535 – LB4/AW, AWZ 536 – LB5/AW (PTC or FTA, with failure indication –

OC type output)

AWZ 573 – LB4/0,3A/PTC, AWZ 574 – LB4/0,5A/PTC, AWZ 575 – LB4/1,0A/PTC,

AWZ 576 – LB4/0,3-1,0A/FTA,

AWZ 577 – LB8/0,3A/PTC, AWZ 578 – LB8/0,5A/PTC, AWZ 579 – LB8/1,0A/PTC,

AWZ 580 – LB8/0,3A-1,0A/FTA

DC voltage reducers

DCDC

RN250 – RN-2,5A/12V

RN500 – RN-5,0A/12V

1.2. Block diagram (fig.1).

Fig.1. Block diagram of the power-supply unit.

1.3. Description of elements and connection links of the power-supply unit (tab.1, tab.2, fig.2, fig.3).

Table 1.

Element no.

[Fig. 2]

Description

[1] F1 fuse in the battery circuit

[2] START pushbutton (power-supply activation from the battery)

[3]

J, jumper - configuration of UVP battery protection function

•

••

• J = protection function (disconnection) of the battery off

•

••

• J = protection function (disconnection) of the battery on

Legend:

jumper installed, jumper removed

[4] P1 potentiometer, DC voltage adjustment

[5]

+AUX-

+AUX1-

+AUX2-

+AUX3- Outputs for DC power supply (+AUX= +U, -AUX=GND)

[6] O1, O2, O3, AUX - optical signalisation of power supply operation

[7] AC - LED diode that indicates the presence of AC voltage

[8] LB - LED diode that indicates battery charging

[9] OVP - LED diode that indicates the activation of the OVP overvoltage protection

[10]

J1, J2, jumpers – battery charging current configuration

• J1= J2= Ibat =0.7A

• J1= J2= Ibat =2.1A

• J1= J2= Ibat =3.6A

• J1= J2= Ibat =4.8A

Legend:

jumper installed jumper removed

[11]

+BAT - DC power supply output of the battery

(+BAT = red, -BAT = black)

[12]

BS - technical output of AC shortage – OC type

hi-Z level = status: AC power supply

L level = status: AC power supply failure

[13]

AW - failure technical output – OC type

Activation: SCP, OLP, UVP, converter failure

L level = status: correct operation

hi-Z level = status: failure, overload

[14]

LED signalisation connection

Tab.1. Elements of the PCB board of the power-supply unit (refer to fig.2).

Fig.2. View of the PCB board of the power-supply unit.

Table 2.

Element no.

[Fig. 3]

Description of outputs of the power-supply unit

[1]

Separation transformer

[2]

Power-supply unit board (tab. 1)

[3] TAMPER micro-switch (contacts) of the anti-sabotage protection (NC)

[4] F2 fuse in the power supply circuit (230VAC)

[5]

L-N 230VAC power supply connection , PE protection connection

[6]

Battery connectors: +BAT = red, -BAT = black

Tab.2.

Elements of the power-supply unit (refer to fig. 3).

Fig.3 View of the power-supply unit.

1.4. Technical parameters:

- electrical parameters (tab.3)

- mechanical parameters (tab.4)

- operation safety (tab.5)

- operation parameters (tab.6)

Electrical parameters (tab.3).

Supply voltage 230V AC (-15%/+10%)

Supply frequency 50Hz

PSU power P 138W

Current consumption 1.1A

Output voltage 11.0V ÷ 13.8V DC – buffer operation

10.0V ÷ 13.8V DC – battery operation

Output voltage setting, escalation and keeping time 20ms / 30ms / 50ms

Voltage setting range 12.5V ÷ 14.2VDC

Pulsating voltage 50mV p-p max.

Output current 1 x 10A – main output +AUX- or

3 x 2.5A - outputs: +AUX1-, +AUX2-, +AUX3-

Power consumption of the power-supply unit systems

during battery operation

20mA max.

Battery charging current 0.7A / 2.1A / 3.6A / 4.8A

SCP short-circuit protection

200% ÷ 250% of power supply,

hiccup mode – 13A/200ms and/or

fuse failure in the battery circuit (fuse-element

replacement required)

OLP overload protection

110% ÷ 150% of power supply – electronic.

Disconnection of power supply outputs – automatic re-

connection after the disconnecting of the DC output

circuit

SCP protection of the battery circuit and reverse

polarity protection

10A - current limitation, F1 fuse (failure requires replace

of the fuse-element)

UVP excessive discharge protection U < 10.0 V (± 5%)

Technical outputs:

- BS output indicating failure of AC power supply

- AW output indicating failure (activation of SCP,

OLP, UVP, converter failure)

- TAMPER output indicating the opening of the power

supply casing

- OC type, 50mA max, normal status: hi-Z level, failure:

level L (0V), 30s time lag.

- OC type, 50mA max, normal status: L(0V) level, failure:

hi-Z level, (automatic return after correct operation is

returned)

- micro-switch x2, NC contacts (closed casing, mounted

on foundation), 0.5A@50V DC (max)

F1 fuse

F2 fuse

F 10A / 250V

T 6.3A / 250V

Mechanical parameters (tab.4).

Casing dimensions 350 x 277 x 168 (345 x 272 x 160+8) (WxHxD) [mm] (+/- 2)

Fixation 315 x 240 x Φ 6 x 4szt (WxH)

Battery space 17Ah/12V (SLA) max.

Net/gross weight 8,1 / 8,6 kg

Casing colour RAL 9003

Closing Cheese screw x 2 (at the front), lock assembly possible

Connectors Power-supply: Φ0.41-2.5

Outputs: Ф0.41÷2.5

BAT battery outputs: connectors Φ6 (M6-0-2.5)

TAMPER output: wires, 300 mm

Notes The casing is distant from the assembly surface so that cables can be installed,

cooling: natural convection

Operation safety (tab.5).

Protection class PN-EN 60950-1:2007 I (first)

Protection grade PN-EN 60529: 2002 (U) IP20

Electrical strength of insulation:

- between input (network) circuit and output circuits of power-supply (I/P-

O/P)

- between input circuit and PE protection circuit (I/P-FG)

- between output circuit and PE protection circuit (O/P-FG)

3000V AC min.

1500V AC min.

500V AC min.

Insulation resistance:

- between input circuit and output or protection circuit

100MΩ, 500V DC

Operation parameters (tab.6).

Operation temperature -10ºC...+40ºC

Storage temperature +25ºC...+60ºC

Relative humidity 30%...90%, without condensation

Vibrations during operation Unacceptable

Impulse waves during operation Unacceptable

Direct isolation Unacceptable

Vibrations and impulse waves during transport According to PN-83/T-42106

2. Installation.

2.1. Requirements.

The buffer power-supply shall be mounted by the qualified installer having appropriate (required and

necessary for a given country) permissions and qualifications for connecting (operating) 230V AC installations and

low-voltage installations. The device shall be mounted in closed rooms, according to the environment class II, of

the normal air humidity (RH=90% max. without condensation) and the temperature within the range from -10°C to

+40°C. The power-supply shall operate in a vertical position so that free and convectional air flow through

ventilating holes of the casing is guaranteed.

Before installation, the balance of the power-supply load shall be performed. During the normal operation,

the sum of currents collected by receivers shall not exceed I=10A (P=138W max.), including the maximum battery

charging current Ibat.

As the power-supply is designed for a continuous operation and is not equipped with a power-switch,

therefore an appropriate overload protection in the power supply circuit shall be guaranteed. Moreover, the user

shall be informed about the method of isolation of the power supply from the power voltage (usually through

assignment and marking of an appropriate fuse in the fuse-box). The electrical system shall be made in

accordance with valid standards and regulations.

2.2. Installation procedure.

1. Before installation is started, the voltage in the 230V power-supply circuit shall be isolated.

2. The power-supply shall be mounted in a selected location and connection cords shall be lead.

3. The power cables (230 VAC) shall be connected to L-N terminals of the power supply. The earth conductor

shall be connected to the terminal marked by the earth symbol . The connection shall be made by means of

a three-core cable (with a yellow and green PE protection wire). The power cables shall be lead to appropriate

terminals of the connection board through bushing.

The circuit of the shock protection shall be performed with a particular care, i.e. the

yellow and green protection wire of the power cable shall be connected from one side to

the terminal marked by the symbol of in the casing of the power-supply. Operation of

the power-supply without the properly made and fully operational circuit of the shock

protection is UNACCEPTABLE! It can result in failure of devices and electric shock.

4. Connect the conductors of the loads to the +AUX-, +AUX1-, +AUX2-, +AUX3- terminals of the terminal box on

the power-supply unit.

5. If necessary, connect the conductors from the equipment to the technical outputs:

- BS AC status indication (alarm panel, controller, signalling unit, LED diode, etc.)

- AW technical output of failure

- TAMPER signalization of power-supply unit opening or separating from foundation.

6. Using the jumper ‘J1’, ‘J2’ determine maximal battery charging current, take into consideration battery

parameters (refer to tab.1 page 4).

7. Using the jumper ‘J’ determine whether the function of disconnecting the discharged battery U<10V (+/-5%) is

to be on or off. The battery protection is on if the jumper ‘J’ is removed.

8. Activate the 230V AC supply (the AC diode should be permanently illuminated, and AUX O1, O2, O3 diode

should be permanently illuminated).

9. Check the output voltage (the power-supply unit voltage without load should be anywhere between

13.6V÷13.9V, and during battery charging 11V÷13.8V). If the value of the voltage requires adjustment, the

setting should be made by means of the potentiometer P1, monitoring the voltage at the AUX output of the

PSU.

10. Connect the battery in accordance with the indications: +BAT red to ‘plus’ , -BAT black to ‘minus’, (the LB red

diode should go on and the lighting intensity should reduce with the charging time elapsed increasing).

11. Once the tests and control operation have been completed, lock the enclosure, cabinet, etc.

3. The power supply operation indication.

3.1. Optical indication.

The PSU is equipped with two diodes on the front panel:

RED DIODE:

• lights – the power-supply unit supplied with 230VAC

• does not light – no 230VAC supply

GREEN DIODE

• lights – DC voltage at the AUX output of the power-supply unit

• does not light – no DC voltage at the AUX output of the power-

supply unit

Moreover, the PSU is equipped with three diodes indicating operation status: AC, LB, AUX, O1, O2, O3,

and UVP, placed on the PCB (fig.2) of the power-supply unit module:

• AC - red diode: under normal status (AC supply) the diode is permanently illuminated. The absence of AC

supply is indicated by the AC diode going off.

• LB - red diode: indicates the battery charging process; the intensity of illumination is dependent on the

charging current.

• AUX - green diode: indicates the DC supply status at the output of the PSU. Under normal status, the

diode is permanently illuminated and in the case of short-circuits or overload, the diode goes off.

• O1, O2, O3 - green diodes: indicate the status of DC power supply at AUX1, AUX2, AUX3 outputs, which

are independently protected with 2.5A polymer safety equipment. In normal state, the diode emits

continuous light – in the case of short-circuit or overload, the diode goes off.

• UVP – red diode: signals the activation of the UVP overvoltage protection. In normal state, the diode

is off – in the case of short-circuit or overload, the diode emits continuous light.

3.2. Technical outputs.

The PSU is equipped with indication outputs:

• BS - absence of AC supply output: - OC output type indicates the loss of AC supply in a normal status,

with the supply equal to 230V, the output is deactivated and in case of power supply loss the PSU

activates the output after 30s.

• AW - technical output of failure: OC output type indicates failure the occurrence of at least one of the

following failures: SCP, OLP, UVP, voltage converter failure. In normal state (correct operation), the output

has the L status "ground" (0V) – in the case of failure, the output is open (hi-Z high impedance).

• TAMPER - output indicates opening the power-supply unit: output as volt-free contacts which indicate

power-supply unit door status and fastening to the ground: NC unit opened and/or wrongly fastened (e.g.

unit unconnected with the ground): NO.

4. Service and operation.

4.1. Overload of short-circuit to the power-supply output.

The output circuit has an electronic current protection. If permissible value of the I

max

output current is

exceeded, the power-supply unit output voltage is disconnected and this is indicated by the O1, O2, O3 and AUX

diodes going off. The voltage is restored automatically, when the receivers are disconnected from the output.

Additionally, the AUX1, AUX2, AUX3 outputs of the power-supply unit are independently protected, using

the PTC polymer fuses. If the output is loaded with the current that exceeds 2.5A, the output voltage is

automatically disconnected, which is indicated by the O1, O2 or O3 green diode going off. The restoration of the

voltage at the output requires the disconnecting output load for the period of at least one minute.

In the case of the short-circuit to the AUX, BAT output, (load 200% ÷ 250% of the PSU power) or incorrect

connection of the battery, the fuse F1 in the battery circuit becomes permanently damaged. The restoration of the

voltage at the BAT output requires the replacement of the fuse.

4.2. Battery operation.

In the case of power failure, in the unit will instantly switch to the battery assisted operation.

In order to activate the operation of the PSU from the battery itself, connect the BAT connectors in accordance with

the indications: +BAT red to ‘plus’ and, -BAT black to 'minus’ of the battery and press and keep depressed for five

seconds the START pushbutton on the equipment board.

The PSU is equipped with the discharged battery disconnection system (UPV); the configuration of

functions through the jumper ‘J’. The battery protection is on if the jumper ‘J’ is removed.

4.3. Maintenance.

Any and all maintenance operations may be performed following the disconnection of the PSU from the

power supply network. The PSU does not require performing any specific maintenance measures, however, in the

case of significant dust rate, its interior is recommended to be cleaned with compressed air. In the case of fuse

replacement, only the substitutes in conformity to the original ones are allowed.

WEEE MARK

The waste electric and electronic products do not mix with general household waste.

There are separate collection system for used electric and electronic products in

accordance with legislation under the WEEE Directive and is effective only with EU.

Notice: The power supply unit is adapted for cooperation with the sealed lead-acid battery (SLA). After the operation period it must not be

thrown but recycled according to the applicable law.

GENERAL WARRANTY CONDITIONS

1. Pulsar K. Bogusz Sp.j. (manufacturer) grants a two-year quality warranty for the equipment, starting from the date of purchase

placed on the purchase order.

2. Should such purchase order be missing when the claim is submitted, the three-year guarantee period is counted from the date

of the manufacturing of the device.

3. The warranty includes free-of-charge repairing or replacing with a functional equivalent (the selection is made by the

manufacturer) of the malfunctioning device, due to reasons attributable to the manufacturer, including manufacturing and material

defects, unless such defects have been reported beyond the warranty period (item 1 and 2).

4. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the

manufacturer.

5. The warranty applies to complete equipment, including the type of defect specified in writing, using a properly filled warranty

claim.

6. Should the claim be accepted, the manufacturer is obliged to render warranty repairs, as soon as possible, however not later

that within 14 days from the delivering of the equipment to the service centre of the manufacturer.

7. The repair period mentioned in item 5 may be prolonged, if there is no technical capability to carry out the repairs, and in the

case that the equipment has been accepted conditionally, due to the failing of the warranty terms by the claimant.

8. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.

9. The warranty does not cover the defects of the equipment, resulting from:

- reasons beyond the manufacturer's control,

- mechanical damage,

- improper storage and transport,

- use that violates the operation manual or equipment application,

- random events, including lightning discharges, failures of power networks, fire, flooding, high temperatures and chemical agents,

- improper installation and configuration (at variance with the rules set forth in the manual),

10. Each confirmation of structural modifications or repairs, carried out beyond the service centre of the manufacturer, or any

modification of serial numbers or warranty labels, results in the loss of the rights resulting from the warranty.

11. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the

wholesale prices suggested by the manufacturer on the day of purchase.

12. The manufacturer shall not be responsible for the defects that resulted from the damaging, malfunctioning or inability to

operate the equipment, particularly, if such defects are the result of failing to abide by the recommendations and requirements

contained in the manual, or the use of the equipment.

Pulsar K.Bogusz Sp.j.

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail:

biuro@pulsar.pl, [email protected]l

http:// www.pulsar.pl

1 / 1

Pulsar PSBC10A12 Operating instructions

Brand: Pulsar

Model: PSBC10A12

Category: Power supply units

Type: Operating instructions

Download PDF

Add to bookmarks

report

Pulsar PSBC10A12 Operating instructions

Pulsar PSBC10A12 Operating instructions

Related papers

Other documents