Joovy Zoom 360 and Zoom ATS User manual

Joovy
Brand
Joovy
Model
Zoom 360 and Zoom ATS
Category
Strollers
Type
User manual
©joovy 2014 • Document Version 040314
Zoom 360
53X
Joovy • 2919 Canton Street • Dallas, TX 75226 • (877) 456-5049 • Fax (214) 761-1774 • Email: customerservice@joovy.com • Website: www.joovy.com
Zoom 360 Instruction Manual
Please read this instruction manual completely before using this stroller. Keep these instructions for future reference.
• Failure to follow these instructions could result in serious injury or death.
• Never leave child unattended.
• Avoid serious injury from falling or sliding out.
• Always use safety belts and ensure that your child is positioned according to these instructions.
• Keep all small parts out of the reach of children while assembling the stroller.
• Be certain that the stroller is fully opened, all of the locking devices are engaged, and the parking device is engaged before allowing children
near the stroller.
• The parking device should always be engaged during the loading and unloading of children.
• Avoid serious injury from the front wheel falling off. Ensure the wheel is properly installed and secure before any use of the stroller.
• The seat is not suitable for a child under 3 months.
• The seat is intended for a child up to a maximum weight of 75 lbs.
• Use of the stroller with a child weighing more than 75 lbs. will cause excessive wear and stress on the stroller and may cause a hazardous
unstable condition.
• Keepwheelsatarecommendedtirepressureof35psiorasspeciedonanyreplacementtire.
• Never allow a child to step on the footrest to get into or out of the stroller.
• Do not use the stroller on stairways or escalators.
• The included parent organizer is for use ONLY on the Joovy Zoom 360 stroller. DO NOT use it on other stroller models.
• Never carry hot beverages or open containers in the parent organizer. Maximum weight allowed is 5 lbs.
• DonotaddanyattachmentnotspecicallyrecommendedbyJoovy.
• Any load attached to handle affects the stability of the product. Hanging purses, shopping bags, parcels, diaper bags, changing bags or other
accessory items from the handle bars or any other parts of the stroller may change the balance of the stroller and cause a hazardous unstable
condition.
• The maximum weight that can be carried in the storage basket is 5 lbs. Excessive weight may result in a hazardous unstable condition.
• The total weight of contents in the seat back pocket should be less than 3 lbs.
• The total weight of contents in the in-seat pockets should be less than 2 lbs.
• Never allow your stroller to be used as a toy.
• Discard all packaging materials properly. Do not allow children to play with them.
• Check your stroller for loose rivets, snaps, worn parts, and torn material or stitching on a regular basis.
• Also check the front wheel attachment and the tether strap attachment regularly for proper function and security.
• Discontinue use of the stroller should it malfunction or become damaged.
• While unfolding the stroller, be careful to keep your ngers from being pinched by moving parts.
1 Unpacking the Product
• Remove everything from the box and identify the parts using Figure 1.1 (not to scale).
A: stroller, B: front wheel, C: 2 rear wheels, D: parent organizer, E: tire pump, and documents (not shown).
• Discard all packaging materials properly including plastic coverings.
• DO NOT allow children to play with any packaging materials.
!
WARNING
!
WARNING
Adult assembly is required for this product.
No Tools Required.
2 Unfolding the Stroller
• Keep children away from stroller while unfolding.
• Orient the stroller with the seat facing up and the handle bars closest to you.
• If necessary, release the locking latch located on the lower right side by lifting the latch off of the catch. See Figure 2.1.
• Pull up on the handlebar so that the stroller unfolds to its upright and locked position.
CAUTION: While unfolding the stroller, be careful to keep your ngers from being pinched by moving parts.
• Ensure that the stroller is completely opened and the latching mechanism is secured before ANY further assembly or use of the stroller.
Please do not return this product to the store
If you experience any difculty with the assembly or use of this product, or if you have a
question regarding these instructions, please contact our Customer Service Department
at (877) 456-5049 between the hours of 8:30 am and 5:00 pm Central Time.
!
WARNING
ALWAYS keep children away from the stroller when unfolding.
Possible pinching hazard - Be careful when unfolding the stroller.
5 Front Wheel Swivel Locks
The stroller can be operated with the front wheel in either swivel mode or locked mode.
• To put the front wheel into locked mode, locate the plastic locking lever just above the front wheel.
• Push this lever to the right (clockwise) and rotate the wheel until it locks automatically in the straight position and an audible click is heard.
See Figure 5.1.
• To unlock the front wheel and use it in swivel mode, push the lever to the left (counter clockwise) until an audible click is heard.
7 Operating the Canopy
• To open the canopy, pull forward on the front edge of the canopy until it is fully extended.
• The canopy and visor can be adjusted into several positions ranging from fully closed to full extended, or any position in between.
See Figure 7.1.
NOTE: The top rear portion of the canopy has a roll back window. To open, pull the rear edge up, roll the ap forward and secure using the
T and elastic attachment.
• To close the canopy, push the front edge of the canopy toward the rear of the stroller.
• Engage the two sets of snaps on the underside of the canopy above the seat to allow maximum head room. See Figure 7.2.
NOTE: When you open the canopy with the snaps engaged, these snaps will automatically unsnap.
6 Rear Wheel Brakes
This stroller is equipped with a linked parking brake for the rear wheels.
• Before placing your child into the stroller or removing them from the stroller, be certain that the rear parking brake is engaged.
• To engage the rear parking brake, push down on the brake lever on the right rear wheel hub of the stroller until you hear an audible click.
See Figure 6.1.
• Check that the brake is properly applied by attempting to push the stroller backwards and forwards.
• To release the brake, lift up on the brake lever until it locks into the UP position and you hear an audible click. See Figure 6.2.
!
WARNING
Always engage the parking brake when the stroller is not being pushed so that it will not roll away. Never leave stroller unattended, especially
on a hill or incline, as the stroller may tip over or slide.
3 Installing/Removing Rear Wheels
• Take one rear wheel and insert it into one of the rear wheel hubs until an audible click is heard.
NOTE: You may need to push the wheel with some force to get it past the locking mechanism. See Figure 3.1.
• Pull outward on the wheel to ensure the wheel is installed properly.
• To remove a wheel, push down on the metal tab on the rear wheel hub and then pull outward on the wheel. See Figure 3.2.
4 Installing the Front Wheel
• With the stroller still tilted backwards on the handle bar, remove the plastic protector from the front forks and discard properly.
NOTE: rst need to lock the forks into place. See section on “Front Wheel Lock” for this procedure.
• Loosen the round nut on one end of the front wheel axle just enough so that the wheel will slide onto the frame forks. BE CAREFUL that you
do not take this nut off completely. If this occurs, be sure to reassemble the metal washer and spring onto the axle before reassembling the
nut onto the axle.
NOTE: The metal washer must be assembled to the axle with the small metal tab facing IN toward the wheel and the SMALL end of the
spring also facing IN toward the wheel.
• Make sure the safety lock on the opposite end of the axle is in the UNLOCKED (straight out) position.
NOTE: You can assemble the front wheel with the safety lock on either side of the stroller.
• Slide the wheel onto the frame forks being sure that the metal washer is on the OUTSIDE of each fork. See Figure 4.1.
• Make sure the small metal tab on the washers on BOTH sides of the wheel are placed into the small hole in the fork. This is a secondary
retaining method to help prevent the wheel from sliding off the forks in case the safety lock accidentally opens.
• While holding the safety lock in the open position, tighten the round nut BY HAND in a clockwise direction until it is as tight as you can get it.
• Push the safety lock DOWN to the closed position and ensure it is tight. See Figure 4.2. You may need to loosen the round nut slightly to
fully close the safety lock.
• Pull outward on the wheel to ensure the wheel is installed properly.
• If the wheel is loose or able to be pulled off the forks, loosen the safety lock to the unlocked position and tighten the round nut further.
Repeat until the wheel is secure.
• To remove the wheel, rotate the safety lock to the unlocked position and loosen the round nut counter clockwise until loose enough to slide
the wheel off of the frame forks.
Zoom 360 Instruction Manual
9 Using and Adjusting the Seat Restraint System
• There are three height adjustment positions for the shoulder harness. Adjust the height to the closest height above your child’s shoulders.
• To adjust the shoulder straps, unbuckle them from the main buckle then threading the shoulder straps through one of the loops. The tallest
position does not use a loop.
• To unlatch the buckle press the center button and remove the male ends of each buckle. See Figure 9.1.
• To separate the shoulder harness from the waist harness, simply slide the waist buckles from the shoulder buckles. See Figure 9.2.
• Carefully place the child in the seat with the shoulder straps over their shoulders and chest. Then place the crotch strap between the child’s
legs.
!
WARNING
Always use the crotch strap in combination with the waist belt. Avoid serious injury from falling or sliding out. Always use the restraint system.
The seat is not suitable for children under 3 months.
!
WARNING
ALWAYS keep children away from the stroller when folding. Possible pinching hazard - Be careful when folding the stroller.
10 Storage Basket
The maximum weight that can be carried in the storage basket is 5 lbs.
11 Folding the Stroller
• Keep children away from stroller while folding.
• Place the canopy into its closed position and pull it all the way toward the rear of the stroller.
• From the front of the stroller, lift the pull tab (Labeled “FOLD”) above legrest, to expose the fold release lever (on the right) and cable located
under the seat. See Figure 11.1.
• While pushing inward on the fold release lever, See Figure 11.2, grasp the handle in the middle of the release cable and pull it up quickly
to allow the stroller to fold. See Figure 11.3.
• Continue pulling up until the stroller is fully folded.
CAUTION: While folding the stroller, be careful to keep your ngers from being pinched by moving parts.
• Be sure that the locking latch on the right side of the stroller is secure. See Figure 11.4.
12 Tire Pump
The tire pump is located inside the storage basket.
• To use the tire pump, pull out the air tube from one end of the air pump and screw it snugly into the opposite end of the pump body.
• Remove protective cap from the tire tube air valve. Attach air tube to the air valve on the tire.
• Pump air into the tube until the tires are lled to 35 psi or as specied on the tire wall.
• When nished, unscrew the air tube from the tire valve and then from the pump. Replace the tube in the end of the pump and return the
pump to its storage location in the basket.
8 Seat Recline Positioning
The seat can be adjusted to any position from upright to reclining. Fully reclined seat for children 3 months and above. All other seat positions
for children 6 months and above ONLY..
• To recline the seat, release the adjustment lock tab from its locked position by pulling it away from the seat back. Continue to pull this lock
tab downward to adjust the seat back to the desired position, then re-engage the lock tab. See Figure 8.1.
• To adjust the seat back to a more upright position, release the adjustment lock tab from its locked position. Then simply pull up on the
adjustment strap ring until the seat back is in the desired position and re-engage the lock tab. See Figure 8.2.
!
WARNING
Whether the seat is upright or reclined, ALWAYS make certain that the recline mechanism is engaged before placing the child in the seat.
Push down on the seatback to be sure it is secure. DO NOT adjust the seat when the child is in the seat.
!
WARNING
Possible pinching hazard - Be careful of the side hinges when opening and closing the canopy.
!
WARNING
DONOToverinatethetires,asthismaycauseapotentiallyhazardouscondition.
The pump may become warm to the touch, but this is not an abnormal condition.
13 Parent Organizer
• To install, place the organizer between the frame just below the handle bar. Separate the hook and loop on one corner, thread it through the
plastic ring and attach. Repeat this step on the other three corners.
• To remove it, detach the hook and loop tabs and unthread them through the plastic rings on all four corners of the organizer.
SATISFACTION GUARANTEED
We want you to be completely satised with your purchase of this product. Should you experience any
difculty in assembling or using this product, or if you have any questions, please contact our Customer
Service Department at (877) 456-5049 between the hours of 8:30 am and 5:00 pm Central Time.
Maintenance
All of the ttings, snaps, locks, rivets, and other hardware and plastic parts on the stroller should be inspected periodically to ensure that they
are secured properly and not damaged or malfunctioning. The safety harness, as well as all other straps and fabric items and their stitching
should also be inspected periodically to ensure that they are secured properly and not loose, torn or otherwise damaged. Please inspect the
front fork and ensure that it swivels freely. All moving parts, such as wheels, brakes, and hinges should also be checked periodically to ensure
they are operating properly.
Any missing, broken, or worn components should be replaced immediately, and the stroller should not be used until they are replaced. Only
original manufacturer’s components should be used. If needed, please contact Joovy at our toll-free phone number.
Cleaning
The fabric material on this stroller can be cleaned using mild household soap or detergent and warm water on a sponge or clean cloth. Always
allow the fabric to completely air dry before using the stroller.
The frame and wheels should always be kept clean and free of dirt and foreign matter, especially after operating the stroller in rain, snow, or
other harsh environments. Use a sponge or cloth dampened with warm water and a mild detergent cleaner to clean the wheels after such use.
Please log onto www.joovy.com to register your new Joovy product.
Zoom 360 Instruction Manual
Qool
moon
HiLo
too
Joovy • 2919 Canton Street • Dallas, TX 75226 • (877) 456-5049 • Fax (214) 761-1774 • Email: customerservice@joovy.com • Website: www.joovy.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Joovy Zoom 360 and Zoom ATS User manual

Joovy
Brand
Joovy
Model
Zoom 360 and Zoom ATS
Category
Strollers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents