VDS Linear 11 is an irreversible operator for swing gates and doors, which can be used for gates with a maximum weight of 200 kg and a maximum width of 2.5 meters. It has a motor power of 50 W and a motor RPM of 1500. The opening time for a 90-degree angle is 15 seconds, and the rod stroke is 400/500 mm. The force of thrust is 1500 N, and the motor current input is 3A. The device has an IP55 protection rating and can operate in temperatures ranging from -20°C to +55°C.
VDS Linear 11 is an irreversible operator for swing gates and doors, which can be used for gates with a maximum weight of 200 kg and a maximum width of 2.5 meters. It has a motor power of 50 W and a motor RPM of 1500. The opening time for a 90-degree angle is 15 seconds, and the rod stroke is 400/500 mm. The force of thrust is 1500 N, and the motor current input is 3A. The device has an IP55 protection rating and can operate in temperatures ranging from -20°C to +55°C.
IRREVERSIBLE OPERATOR
FOR SWING GATES
AND DOORS
WARNING!! Before installing, thoroughly read this manual that is an integral
part of the pack
The CE mark conforms to European directive
EEC 89/336 + 92/31 + 93/68 D.L. 04/12/1992 N. 476.
Our products if installed by qualified personnel capable to evaluate risks,
comply with norms UNI EN 12453, EN 12445
LINEAR-11
PACKING CONTENTS .............................................................................
2
VIEW OF TYPICAL AUTOMATION AND NAMES OF COMPONENTS .............
3
TECHNICAL DATA....................................................................................
3
DIMENSIONS .........................................................................................
4
TYPICAL CONNECTION AND CABLE SECTION..........................................
4
CONSIDERATIONS FOR INSTALLATION...................................................
5
INSTALLATION.......................................................................................
5-6
TROUBLESHOOTING...............................................................................
7
SAFETY PRECAUTIONS ..........................................................................
8
PACKING CONTENTS
1- OPERATOR
1- KIT FASTENING PLATES AND
RELATIVE ACCESSORIES
1- UNLOCKING KEY
1- CONDENSER (230Vca)
Max. weight of gate
200 Kg
Max. width of gate
2,50 mt
Motors power supply
24Vdc 230 Vac
Motor power
50 W 200 W
Motor RPM
1500 1400
Condenser
/ 12,5 µF
Mechanical unlock for emergency manoeuvre
With key
Working temperature
-20° C / +55° C
weight
6.5 Kg
Protection rating
IP 55
Opening time 90°
15 sec
Rod stroke 400/500 mm
Force of thrust 1500 N
Motor current input 3 A 1 A
2
5
4
3
1
1
5
6
7
8
VIEW OF TYPICAL AUTOMATION AND NAMES OF COMPONENTS
Optimal installation
1- Operator
2- External photocell
3- Flashing warning light
4- Antenna
5- Internal photocell
6- Electronic control unit
7- Key-switch
8- Remote control
TECHNICAL DATA
DIMENSIONS
TYPICAL CONNECTION AND CABLE SECTION
2X1,5mm2 (24 Vdc )
4X1,5mm2 (230 Vca )
2X0,75mm2
4X0,75mm2
4X0,75mm2
2X0,75mm2
3X1,5mm2
230V Line
RX Photocell
TX Photocell
300 mm
250 mm
520/620 mm
400/500 mm
88 mm
88 mm
INSTALLATION
CONSIDERATIONS FOR INSTALLATION
· The installation and testing operations must be performed solely by qualified personnel in
order to guarantee the proper and safe operation of the automatic gate.
· The company declines any responsibility for damage caused by incorrect installations due
to incompetence and/or negligence.
· Before assembling the automatism, check that the gate is in perfect working order, hangs
well on its hinges and is suitably lubricated. It must also comply with the safety standards
in force in the country of installation..
1 - Before fastening the brackets provided, establish the coordinates using the data given in
Table 1, bearing in mind that they are valid if the operator is at maximum extension minus one
centimetre of the available stroke (CD) when the gate is closed to obtain maximum working
efficiency.
2- Data B in the table, with reference to the single values A, are to be considered as values
(recommended).
3- To anchor the piston, use the fastening brackets provided.
COORDINATES AND TABLE
1. Establish coordinates A + B that are
to be used.
2. Note: The available stroke (CD) of
the operator must never be equal or
greater than the stroke used (CU)
3. The sum of coordinates A + B,
establishes the stroke used CU .
TABLE 1
Note1: A+B = CU (Stroke used) CD = (Available stroke) = 400/500 mm
Opening angle A B Cu
90° Available stroke = 400mm
160
160
320
175
175
350
190
190
380
200
200
400
90° Available stroke = 500mm
250
250
500
INSTALLATION OF FASTENING PLATES
Fix the back plate to the
pillar.(FIG. 1)
Anchor the rear part of the piston
to the plate and fasten it firmly
( FIG. 2)
Warning! When establishing the height off the ground at which to fasten the plate to the post
(fig. 1), keep in mind that the plate for anchoring the piston to the gate must be fastened at the
same level (fig. 3)
To unblock the operator, use
the key as shows the photo.
Turning the key of 90°, the
operator will be completely
unblocked.
(FIG. 3)
(FIG. 1)
(FIG. 2)
(FIG. 4)
Installing the anchor plate on the piston to the gate
1. Fit the anchor plate onto the piston (fig. 4)
2. Close the gate
3. Move the piston with the plate already fitted
towards the gate
4. Move the fitting to limit stop, then move it
back by approximately 1 cm and mark the
position of the plate.
5. realize the same operation in opening.
6. If positions correspond, fix the plate on the
gate; otherwise revise A and B units (table 1)
Release procedure
Blocked Unblocked
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE
SOLUTION
On giving a command with
the remote
control or with the
key-switch, the gate
doesn’t open or the motor
doesn’t start
230 volt mains voltage
absent
Check master switch
Emergency STOP present
Check for any STOP
selectors or commands.
If not used, check jumper
on STOP contact input on
the control board
Fuse blown
Replace with one of same
value.
Power cable of motor or
motors not
connected or faulty.
Connect the cable to
appropriate
terminal or replace.
The photocell is not
functioning or the
beam is interrupted
Check the connection,
remove any
obstacle across the beam
On giving a command with
the remote control, the
gate doesn’t open but
works with the key
command
The remote control has not
been
memorised or the battery
is flat
Carry out the remote
control learning
procedure on the radio
receiver or replace the
battery with a new one..
The gate starts, but stops
immediately
The force of the motor or
motors is insufficient
Modify the value with the
FORCE trimmer on the
control unit
One wing opens and the
other closes
The connection is not
correct
Invert the connection of
the cable of the motor
which rotates in the wrong
sense
N.B. - If the problem persists, contact your Retailer or the nearest Service
Centre
Rev. 1-07/11 ING
SAFETY PRECAUTIONS
These warnings are an essential, integral part of the product and must be given to the user. They
provide important indications on the installation, use and maintenance and must be read carefully.
This form must be preserved and passed on to subsequent users of the system. The incorrect
installation or improper use of the product may be dangerous.
INSTALLATION INSTRUCTIONS
• The installation must be performed by professionally skilled personnel and in compliance with
current local, state, national and European legislation.
• Before beginning the installation, check the integrity of the product.
• The laying of cables, electrical connections and adjustments must be workmanlike performed.
• The packing materials (cardboard, plastic, polystyrene, etc.) are a potential hazard and should
be disposed of correctly and not left within reach of children.
• Do not install the product in potentially explosive environments or environments disturbed by
electromagnetic fields. The presence of inflammable gases or fumes is a grave danger to
safety.
• Set up a safety device for overvoltage, a disconnecting and/or differential switch suitable for
the product and conforming to current standards.
• The manufacturer declines any and all responsibility for product integrity, safety and operation
in the event incompatible devices and/or components are installed.
• Solely original spare parts should be used for repairs and replacements.
• The installer must provide all the information relating to the operation, maintenance and use of
the individual parts, components and system as a whole.
WARNINGS FOR THE USER
• Read the instructions and enclosed documentation carefully.
• The product must be used for the express purpose for which it was designed. Any other use is
considered improper and therefore hazardous. In addition, the information given in this
document and in the enclosed documentation may be subject to modifications without prior
notice. It is given as an indication only for product application. The company declines any
responsibility for the above.
• Keep products, devices, documentation and anything else provided out of reach of children.
In the event of maintenance, cleaning, breakdown or faulty operation of the product, cut off the
power and do not attempt to operate on the product. Contact solely the professionally skilled
personnel responsible for these operations. Failure to adhere to the above indications may be
dangerous.
The data and images are for guidance only
VDS reserves the right to change at any time characteristics of the products described in
its sole discretion, without notice.
Via Circolare p.i.p. N° 10
65010 Santa Teresa di Spoltore (PE) - ITALY
Tel. +39 085 4971946 - FAX +39 085 4973849
www.vdsconsorzio.it - [email protected]
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
VDS Linear 11 is an irreversible operator for swing gates and doors, which can be used for gates with a maximum weight of 200 kg and a maximum width of 2.5 meters. It has a motor power of 50 W and a motor RPM of 1500. The opening time for a 90-degree angle is 15 seconds, and the rod stroke is 400/500 mm. The force of thrust is 1500 N, and the motor current input is 3A. The device has an IP55 protection rating and can operate in temperatures ranging from -20°C to +55°C.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
