Traceable 6548 Owner's manual

Brand: Traceable

Model: 6548

Type: Owner's manual

DESCRIPTION

Mini-Logger-Trac™ is the revolutionary, multi-use, user

programmable, electronic temperature data recorder specif-

ically designed for measuring environmental temperatures

during the transportation of refrigerated vaccines, biological

material, chemicals, pharmaceuticals, and for documenting

the transportation of perishable commodities.

FIGURE 1

MIN/MAX

RECORDINGS

ALARM TRIGGERED

SLEEP

CURRENT

TEMPERATURE

TIME OUTSIDE ALARM

(TOA)

RUNTIME/CUMULATIVE

ALARM TIME

START/STOP

BUTTON

LCD DISPLAY

MIN/MAX RECORDINGS – The minimum and maximum

temperatures that have occurred since the device was

initialized.

ALARM TRIGGERED – Indicates the temperature is in an

active alarm state.

SLEEP — Indicates unit is in stand by mode

CURRENT TEMPERATURE – Current temperature

reading.

TIME OUTSIDE ALARM (TOA) SYMBOL– Indicates cumu-

lative time outside alarm duration is being displayed.

RUN TIME/CUMULATIVE ALARM TIME – Indicates the

amount of time passed since the thermometer logging

was initialized/started. However, when the TOA symbol is

present, the Cumulative Alarm Time is being displayed.

START/STOP BUTTON – The button is used to start the

device logging once it has been initialized. Hold button

down for 5 seconds to activate logging. If the Stop key

feature is enabled, pressing and holding the button will stop

logging preemptively. Note: if the thermometer is stopped

using the Stop button, the thermometer must be reinitialized

using the MaxiThermal software before logging may be

restarted.

PRE-PROGRAMMED SETTING

All units are pre-programmed at factory with the following

settings:

• Temperature units: Celsius

• Alarm setting – Minimum: 2°C Maximum: 8°C

• Recording duration: 30 days

• Recording interval: 5 minutes 33 seconds

• User Stop Key Enable: enabled

• Start delay: 15 minutes

PROGRAMMABLE USER SETTINGS

Through MaxiThermal software (not included) and USB

interface (not included), user is able to program the unit

to their specic requirements. Programmable options are

listed as follows:

• Description – Each Logger-Trac™ device may be

programmed with a unique description. This allows the

user to identify at the time of download where the device

was used.

• Time zone – Set time on unit to a specic time zone.

• Auto Adjust Daylight Time enable – The internal clock

will automatically adjust when daylight savings time shift

occurs.

• Temperature Measurement Units (Celsius/Fahren-

heit) – The temperature data will display on LCD in

selected measurement units.

• Start delay – When this feature is used, a time delay

occurs before data recording is started after the user

presses the START button.

• Recording duration/Sample Interval – User can either

select the data recording interval or the total recording

duration. Note the parameters are dependent upon

each other so changing one eld also changes the other.

• Alarm setting – Maximum and minimum alarm tem-

perature boundaries can be set. Setting resolution is 1°.

• No alarm – Disable the alarm with this option.

• User Stop Key Enable – This feature allows the user to

halt data recording by holding down the START button

on the device once recording is started.

HOW TO START THE DATA LOGGER

1. When ready to begin recording, press and hold the

START button for 5 seconds on the front panel. The

LCD will become active and display the current tem-

perature as well as the REC symbol to indicate logging

is now active.

2. Place thermometer in environment to begin monitoring.

HOW TO STOP THE DATA LOGGER

1. User may stop the thermometer logging by pressing

and holding the START button for 3 seconds. The LCD

will display the word END once logging is stopped.

The logging can also be stopped in advance of the

preprogrammed logging duration time by plugging the

thermometer into the USB cradle (not included) and

selecting Stop under the Logger Menu in MaxiThermal

software (not included). Once the device has been

stopped, the user may download the logged data from

the thermometer.

2. Logging cannot be restarted until the thermometer has

been reinitialized using MaxiThermal. Pressing START

will not reactive the unit.

UPLOADING DATA TO PC

1. Insert Logger-Trac Mini to USB cradle (Cat. No. 6549)

2. Connect USB cradle to PC

3. Open MaxiThermal software (Cat. No. 6580)

4. See MaxiThermal instructions for uploading data to PC

HOW TO REPLACE BATTERY

On back the Data Logger, unscrew the four screws, remove

the battery cover, remove the battery, and replace with a

new CR2032 3V Lithium Coin Cell battery. Replace the

panel, and screw the back panel onto the unit.

WARRANTY, SERVICE, OR RECALIBRATION

For warranty, service, or recalibration, contact:

CONTROL COMPANY

12554 Old Galveston Rd. Suite B230

Webster, Texas 77598 USA

Ph. 281 482-1714 • Fax 281 482-9448

E-mail [email protected] • www.traceable.com

Control Company is ISO 9001:2008 Quality-Certied

by DNV and ISO/IEC 17025:2005 accredited as a

Calibration Laboratory by A2LA.

MINI-

LOGGER-TRAC

INSTRUCTIONS

™

Control Company Cat. No. 6548

Traceable 6548 Owner's manual

Traceable 6548 Owner's manual

Traceable 6548 Owner's manual

Related papers

Other documents