Scalextric digital ARC PRO Quick start guide

Brand
Scalextric digital
Model
ARC PRO
Type
Quick start guide
ENGLISH .......................................................................................................
FRANÇAIS ....................................................................................................
DEUTSCH .....................................................................................................
ITALIANO ......................................................................................................
ESPAÑOL .....................................................................................................
REGULATORY COMPLIANCE INFORMATION ................................
3
25
47
69
91
113
TRANSLATION CONTENTS -
2
- CONTENTS
3
CONTENTS PAGE .....................................................................................
POWERBASE & CONTROLLER GUIDE .............................................
LED BEHAVIOUR ......................................................................................
QUICK START GUIDE:
STAGE 1 - DOWNLOAD APP ..................................................
STAGE 2 - CONNECT APP .......................................................
STAGE 3A - CONNECT CONTROLLERS .............................
STAGE 3B - CONNECT CONTROLLERS .............................
STAGE 4 - CONNECT CARS ...................................................
LANE CHANGING ......................................................................................
POWERBASE SETUP..............................................................................
PIT LANE GUIDE .......................................................................................
SPECIAL FEATURES ...............................................................................
DRAG RACE GUIDE ..................................................................................
CAR CALIBRATION ..................................................................................
IN-RACE APP GUIDE ...............................................................................
RUMBLE PATTERNS ..............................................................................
FEATURE LIST ...........................................................................................
TROUBLESHOOTING ..............................................................................
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
20
21
22
A
A
C
C
B
B
D
D
A
C
B
D
E
E
F
F
G
H
G
POWERBASE & CONTROLLER GUIDE -
4
KEY:
Power/Bluetooth LED
Binding Buttons
Binding LEDs
Round Power Sockets
USB Port
Analogue/Digital Switch (note; Analogue
mode will switch to ARC AIR functionality.
ARC AIR will only run 2 analogue cars, with
no lane changing function available)
KEY:
Power Switch
Power/Bluetooth LED
Trigger
Battery Screw
Battery Door
Lanyard Loop
Brake Button
Lane Change Button
E
F
A
C
B
D
E
F
H
Green Solid
- LED BEHAVIOUR
5
Controller is in
binding mode/
battery is low
1
2
3
Download and install the Scalextric ARC App from Google Play or the iTunes App Store.
DOWNLOAD APP -
6
1
STAGE
3
- CONNECT APP
7
4
5
When the powerbase power/
Bluetooth LED glows solid green,
you are ready to race.
Open the ARC App on your smart
device and follow the on screen
instructions.
The powerbase power/Bluetooth
LED will ash orange.
Plug transformer into the wall and
turn on.
Insert the round plugs into the
powerbase.
2
STAGE
Press and hold binding button on powerbase for colour you wish to connect to – LED will ash
green to indicate binding mode.
Please note: Your hand controllers should already be connected. However if they are not, or you
wish to connect your controller to a different colour, please follow the steps below;
Turn off the controller
CONNECT CONTROLLERS -
8
3A
STAGE
- CONNECT CONTROLLERS
9
4
5
6
Continue holding the trigger and turn the controller on.
Release the trigger – your controller is now connected!
4
3B
STAGE
10
CONNECT CARS -
Place car onto track. (NOTE; only 1 car on the track at a time)
Ensure the controller is switched on.
Double press the coloured button on the powerbase to connect your car to the
corresponding controller. This will cause the LED to ash.
When LED glows solid green, the car is connected.
Gently pull trigger to test connection.
4
5
Please Note: Your car should already be connected to the controller. However if it is not, or
you wish to connect your car to a different colour, please follow the steps below
4
4
STAGE
11
- LANE CHANGING
Identify the sensors on the lane change sections of track.
During the race, before reaching the sensor, press and hold lane change button.
Once the car has passed sensor, release the lane change button.
The lane change point will click and the car will change lanes.
4
4
USING THE LANE CHANGER
12
POWERBASE SETUP -
The Powerbase MUST NOT go in the centre of the pit lane, as this will not register a lap when going through
the pit lane.
To avoid this, connect the power base in the correct position, either before or after the pit lane, when setting
up the track.
IMPORTANT
It is recommended
that the powerbase
is assembled in the
middle or at the
end of a striaght,
not directly after a
corner, as this can
result in some laps
not registering in
extreme cases.
Pit Lane Setup
Powerbase Setup
13
To enter the pit lane, press the lane change button.
When in the pitlane, press and hold the brake button to come to a full stop.
Continue holding the brake button.
After 2 seconds, pit stop will be activated. Continue holding the brake button until
you are ready to leave the pit lane.
To leave the pit lane, release the brake button and press the trigger as normal.
4
4
You can not enter the pit lane from this lane
5
5
Note: The pitstop fuctionality can be activated anywhere on the track (ie drivers do not have to enter the pitlane in order for the
pitstop button to work). However, it is recommended that a pitlane is used when racing in ARC PRO mode in order to avoid
collisions in the same lane whilst racing.
- PIT LANE GUIDE
14
SPECIAL FEATURES -
When the Yellow Flag feature is activated in settings, you can use Yellow Flag
Mode.
If a car comes off of the track, tap the screen of your smart device to raise the
yellow ag and restrict all racers speed to 5%.
When the car is reconnected with the track, tap the screen again to return all racers
to full power.
When the KERS feature is active in settings, you can use KERS
To activate KERS boost, double press the lane change button; this will unlock the
full power for your car.
When KERS is active, power will be limited to 80%. When fully charged, KERS will
give the car 100% power for 3 seconds.
Yellow Flag Mode
KERS
- DRAG RACE GUIDE
15
A
C
B
D
E
A
C
B
E
D
Your car must be calibrated to race correctly while the in-race features are active.
16
CAR CALIBRATION -
17
- CAR CALIBRATION
18
.
When KERS is activate, power
will be limited to 80%. When
fully charged KERS will give the
car 100% power for 3 seconds.
KERS
50%
DRIVER COLOUR
TYRES
1
7
6
5
2
9
8
4
3
IN-RACE APP GUIDE -
Leave pits
Yellow Flag
Tyre blowout
Enter pits
- IN-RACE APP GUIDE
19
Please note: The car's speed will be
reduced if you are using the wrong
tyres for the weather conditions.
Change your tyres by entering the pits.
Light showers/Heavy
Fast revving-like rumble
RUMBLE PATTERNS -
20
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Scalextric digital ARC PRO Quick start guide

Brand
Scalextric digital
Model
ARC PRO
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents