Kelvinator NS4BD-KA/B User guide

NS4BD-KA/B
Kelvinator
Brand
Kelvinator
Model
NS4BD-KA/B
Type
User guide

This manual is also suitable for

QUICK REFERENCE DATA
*S4BD Series Residential Split System Air Conditioner
Table 2. Thermostat Wire Gauge
Thermostat
Wire Gauge
Recommended T-Stat Wire
Unit to T-Stat (Length in FT)
2-Wire
(Heating)
5-Wire
(Heating/Cooling)
24 55 25
22 90 45
20 140 70
18 225 110
Table 1. Electrical Specifications & Physical Data
MODEL NUMBER: *S4BD- 018KB 024KB 030KB 036KB 042KB 048KB 060KB
Electrical
Data
Volts-Cycles Phase (1) 208 / 230 - 60 - 1
Total Amps 9.3 13.5 14.8 18.0 19.4 23.2 27.8
Delay Fuse Max. (2) 20 25 30 35 40 50 60
Min. Circuit Ampacity 11.6 16.7 18.3 22.2 23.9 28.7 34.4
Component
Data
Coil
Area 8.3 8.3 10.0 10.0 15.3 15.3 17.9
Rows-FPI 1-18
Tube Dia. Micro-Channel
Fan Motor
Type PSC
Amps 0.35 0.7 0.7 1.4 1.5 1.5 1.5
HP 0.05 0.1 0.1 0.25 0.25 0.25 0.25
Compressor Data
RLA 9.0 12.8 14.1 16.6 17.9 21.8 26.4
LRA 48.0 58.3 73.0 79.0 112.0 117.0 134.0
REFRIGERANT SUCTION LINE O.D
NOTE: Liquid line is 3/8” O.D. for entire length.
0 - 24 ft. 3/4” 3/4” 3/4” 3/4” 7/8” 7/8” 7/8”
25 - 39 ft. 3/4” 3/4” 3/4” 7/8” (3) 7/8” 7/8” 1-1/8” (4)
40 - 75 ft. 3/4” 3/4” 3/4” 7/8” (3) 7/8” 7/8” 1-1/8” (4)
REFRIGERANT CHARGE
R-410A in ounces for outdoor unit & 15' Lineset. (5)
40.4 41.0 40.0 41.0 59.0 60.0 69.6
APPROXIMATE WEIGHT (LBS.)
Net 109 125 138 140 179 179 188
Ship 114 130 144 146 187 187 197
(1) Operating Voltage Range: 187v min. — 253v max.
(2) HACR Type Circuit Breakers may be used.
(3) Requires 7/8" to 3/4" reducer from line to unit.
(4) Requires 7/8" to 1-1/8" reducer from line to unit.
(5) Additional charge for line sets above 15 feet. Values based on
suction line as follows with 3/8" liquid line.
(a) 3/4" = 0.6 oz. per additional foot.
(b) 7/8" = 0.7 oz. per additional foot.
(c) 1 1/8" = 0.8 oz. per additional foot.
Table 3. Unit Dimensions
MODEL
NUMBER
HEIGHT
(H)
WIDTH
(W)
DEPTH
(D)
*S4BD-018KB 23 1/2" 22 3/4" 22 3/4"
*S4BD-024KB 23 1/2" 22 3/4" 22 3/4"
*S4BD-030KB 27 1/2" 22 3/4" 22 3/4"
*S4BD-036KB 27 1/2" 22 3/4" 22 3/4"
*S4BD-042KB 27 1/2" 30 3/4" 30 3/4"
*S4BD-048KB 27 1/2" 30 3/4" 30 3/4"
*S4BD-060KB 31 1/2" 30 3/4" 30 3/4"
D
W
H
Model JS4BD Shown
Figure 1. Clearance Requirements
2” Mounting Pad
24" for
Service Access
12" or 18”
See Note
12" or 18”
See Note
DO NOT
OBSTRUCT
TOP OF UNIT
NOTE: Units require full perimeter clearances.
Installer must maintain 18” between two units
or 12” between single unit and structure.
6” from Building
or Structure
48”
2
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BD-030KB/B4VM-X30K-Bmatch,theappropriateTXVis
the 669565 and 36 ounces of charge will need to be added. (CHANGE
IN CHARGE)
• Forthe*S4BD-024KB/B6EMMX24K-Bmatch,theappropriateTXVis
the669564andnoadditionalchargeneedstobeadded.(NOCHANGES
ARENECESSARY)
Table 4. Restrictor or TXV / Charge Addition (Oz)
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BD- 018KB 024KB 030KB 036KB 042KB 048KB 060KB
ID Restrictor Supplied With OD Unit: 0.048 0.056 0.060, 0.061 0.065, 0.067 0.071, 0.072 0.076, 0.077
Outdoor Unit BOM Charge (Oz.) 40.4 41 40 41 59 60 69.6
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW (SCFM))
B4VM
B4VM-X24K-A 669564
669564
(30 / 550)
669564
(29 / 700)
-- -- -- -- --
B4VM-X24K-B 669564
669564
(30 / 550)
669564
(29 / 700)
-- -- -- -- --
B4VM-X30K-A 669565 -- --
669565
(36 / 950)
-- -- -- --
B4VM-X30K-B 669565 -- --
669565
(36 / 950)
-- -- -- --
B4VM-X36K-B 669566 -- -- --
669566
(31 / 950)
-- -- --
B4VM-X48K-B 669568 -- -- -- --
669568
(34 / 1250)
-- --
B4VM-X48K-C 669568 -- -- -- --
669568
(34 / 1250)
669568
(36 / 1400)
--
B4VM-X60K-C 669578 -- -- -- -- -- --
669578
(36 / 1600)
GB5BM-0
GB5BM-024K-A 0.055
0.048
(30 / 675)
0.055
(29 / 700)
-- -- -- -- --
GB5BM-024K-B 0.055
0.048
( 30 / 675)
0.055
(29 / 700)
-- -- --
-- --
GB5BM-030K-A 0.065 -- --
0.065
(36 / 950)
-- -- -- --
GB5BM-030K-B 0.065 -- --
0.065
(36 / 950)
-- -- -- --
GB5BM-036K-B 0.073 -- -- --
0.073
(31 / 950)
-- -- --
GB5BM-042K-B 0.077 -- -- -- --
0.077
(34 / 1250)
-- --
GB5BM-048K-C 0.080 -- -- -- -- --
0.080
(36 / 1400)
--
GB5BM-060K-C 0.089 -- -- -- -- -- --
0.089
(36 / 1600)
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Numberslistedas0.***arerestrictordiameters,whilenumberslistedas669***areTXVpartnumbers.
3
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BD-030KB/B4VM-X30K-Bmatch,theappropriateTXVis
the 669565 and 36 ounces of charge will need to be added. (CHANGE
IN CHARGE)
• Forthe*S4BD-024KB/B6EMMX24K-Bmatch,theappropriateTXVis
the669564andnoadditionalchargeneedstobeadded.(NOCHANGES
ARENECESSARY)
Table 4. Restrictor or TXV / Charge Addition (Oz) - Continued
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BD- 018KB 024KB 030KB 036KB 042KB 048KB 060KB
ID Restrictor Supplied With OD Unit: 0.048 0.056 0.060, 0.061 0.065, 0.067 0.071, 0.072 0.076, 0.077
Outdoor Unit BOM Charge (Oz.) 40.4 41 40 41 59 60 69.6
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW (SCFM))
GB5BMM
GB5BMM024K-A 0.055
0.048
(0 / 555)
0.055
(3 /700)
-- -- -- -- --
GB5BMM024K-B 0.055
0.048
(0 / 550)
0.055
(3 / 720)
-- -- -- -- --
GB5BMM030K-A 0.062 -- --
0.060
(8 / 920)
-- -- -- --
GB5BMM030K-B 0.062 -- --
0.060
(8 / 890)
-- -- -- --
GB5BMM036K-B 0.067 -- -- --
0.065
(15 / 1160)
-- -- --
GB5BMM042K-B 0.074 -- -- -- --
0.072
(0 / 1370)
-- --
GB5BMM048K-B 0.079 -- -- -- -- --
0.079
(2 / 1355)
--
GB5BMM048K-C 0.079 -- -- -- -- --
0.079
(2 / 1630)
--
GB5BMM060K-C 0.087 -- -- -- -- -- --
0.087
(0 / 1950)
B5BM-X
B5B(M,V)-X24K-A 669564
669564
(30 / 675)
669564
(29 / 700)
-- -- -- -- --
B5B(M,V)-X24K-B 669564
669564
(30 / 675)
669564
(29 / 700)
-- -- -- -- --
B5B(M,V)-X30K-A 669565 -- --
669565
(36 / 950)
-- -- -- --
B5B(M,V)-X30K-B 669565 -- --
669565
(36 / 950)
-- -- -- --
B5B(M,V)-X36K-B 669566 -- -- --
669566
(31 / 950)
-- -- --
B5B(M,V)-X42K-B 669567 -- -- -- --
669567
(34 / 1250)
-- --
B5B(M,V)-X48K-B 669568 -- -- -- -- --
669568
(36 / 1400)
--
B5B(M,V)-X48K-C 669568 -- -- -- -- --
669568
(36 / 1400)
--
B5B(M,V)-X60K-C 669578 -- -- -- -- -- --
669578
(36 / 1600)
B5BW
GB5BW-030K(*) 0.063†
0.050
(30 / 660)
0.057
(29 / 675)
0.063
(36 / 760)
-- -- -- --
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Numberslistedas0.***arerestrictordiameters,whilenumberslistedas669***areTXVpartnumbers.
† TheGB5BW-030Kunitissuppliedwithextra0.050,0.057,and0.065restrictors.
4
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• For the*S4BD-030KB/B4VM-X30K-Bmatch,theappropriateTXVis
the 669565 and 36 ounces of charge will need to be added. (CHANGE
IN CHARGE)
• Forthe*S4BD-024KB/B6EMMX24K-Bmatch,theappropriateTXVis
the669564andnoadditionalchargeneedstobeadded.(NOCHANGES
ARENECESSARY)
Table 4. Restrictor or TXV / Charge Addition (Oz) - Continued
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BD- 018KB 024KB 030KB 036KB 042KB 048KB 060KB
ID Restrictor Supplied With OD Unit: 0.048 0.056 0.060, 0.061 0.065, 0.067 0.071, 0.072 0.076, 0.077
Outdoor Unit BOM Charge (Oz.) 40.4 41 40 41 59 60 69.6
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW (SCFM))
B6BMM0
B6BMM024K-A 0.055
0.048
(0 / 555)
0.055
(3 / 700)
-- -- -- -- --
B6BMM024K-B 0.055
0.048
(0 / 550)
0.055
(3 / 720)
-- -- -- -- --
B6BMM030K-A 0.062 -- --
0.060
(8 / 920)
-- -- -- --
B6BMM030K-B 0.062 -- --
0.060
(8 / 890)
-- -- -- --
B6BMM036K-B 0.067 -- -- --
0.065
(15 / 1160)
-- -- --
B6BMM042K-B 0.074 -- -- -- --
0.072
(0 / 1370)
-- --
B6BMM048K-B 0.079 -- -- -- -- --
0.079
(2 / 1355)
--
B6BMM048K-C 0.079 -- -- -- -- --
0.079
(2 / 1630)
--
B6BMM060K-C 0.087 -- -- -- -- -- --
0.087
(0 / 1950)
B6BM-X
B6BM-X24K-A 669564
669564
(30 / 675)
669564
(29 / 825)
-- -- -- -- --
B6BM-X24K-B 669564
669564
(30 / 650)
669564
(28 / 800)
-- -- -- -- --
B6BM-X30K-A 669565 -- --
669565
(36 / 950)
-- -- -- --
B6BM-X30K-B 669565 --
669565
(29 / 700)
669565
(36 / 950)
-- -- -- --
B6BM-X36K-B 669566 -- -- --
669566
(40 / 1145)
-- -- --
B6BM-X42K-B 669567 -- -- -- --
669564
(34 / 1250)
-- --
B6BM-X48K-C 669568 -- -- -- -- --
669568
(34 / 1585)
--
B6BM-X60K-C 669578 -- -- -- -- -- --
669578
(36 / 1600)
B6BW
B6BW-018K(*) 0.056
0.048
(0 / 600)
-- -- -- -- -- --
B6BW-024K(*) 0.057 --
0.057
(3 / 800)
-- -- -- -- --
B6BW-030K(*) 0.060 -- --
0.060
(8 / 950)
-- -- -- --
B6BW-036K(*) 0.069 -- -- --
0.067
(0 / 1100)
-- -- --
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Numberslistedas0.***arerestrictordiameters,whilenumberslistedas669***areTXVpartnumbers.
5
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BD- 018KB 024KB 030KB 036KB 042KB 048KB 060KB
ID Restrictor Supplied With OD Unit: 0.048 0.056 0.060, 0.061 0.065, 0.067 0.071, 0.072 0.076, 0.077
Outdoor Unit BOM Charge (Oz.) 40.4 41 40 41 59 60 69.6
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW (SCFM))
B6EM
B6EMMX24K-A 669564
669564
(0 / 670)
669564
(0 / 740)
-- -- -- -- --
B6EMMX24K-B 669564
669564
(0 / 530)
669564
(0 / 690)
-- -- -- -- --
B6EMMX30K-A 669565 -- --
669565
(2 / 960)
-- -- -- --
B6EMMX30K-B 669565 -- --
669565
(2 / 910)
-- -- -- --
B6EMMX36K-B 669566 -- -- --
669566
(6 / 1155)
-- -- --
B6EMMX42K-B 669567 -- -- -- --
669567
(4 / 1265)
-- --
B6EMMX48K-C 669852 -- -- -- --
669852
(5 / 1465)
669852
(3 / 1430)
--
B6EMMX60K-C 669578 -- -- -- -- -- --
669578
(0 / 1605)
B6VM
B6VMAX24K-A 669564
669564
(30 / 550)
669564
(29 / 700)
-- -- -- -- --
B6VMAX24K-B 669564
669564
(30 / 525)
669564
(29 / 700)
-- -- --
-- --
B6VMAX30K-A 669565 -- --
669565
(36 / 950)
-- -- -- --
B6VMAX30K-B 669565 --
669565
(29 / 700)
669565
(36 / 950)
-- -- -- --
B6VMAX36K-B 669566 -- -- --
669566
(31 / 1100)
-- -- --
B6VMAX42K-B 669567 -- -- -- --
669567
(34 / 1250)
-- --
B6VMAX48K-C 669568 -- -- -- --
669568
(34 / 1250)
669568
(36 / 1400)
--
B6VMAX60K-C 669578 -- -- -- -- -- --
669578
(36 / 1600)
B6VMMX
B6VMMX24K-A 669564
669564
(0 / 670)
669564
(0 / 740)
-- -- -- -- --
B6VMMX24K-B 669564
669564
(0 / 530)
669564
(0 / 690)
-- -- -- -- --
B6VMMX30K-A 669565 -- --
669565
(2 / 960)
-- -- -- --
B6VMMX30K-B 669565 -- --
669565
(2 / 910)
-- -- -- --
B6VMMX36K-B 669566 -- -- --
669566
(6 / 1155)
-- -- --
B6VMMX42K-B 669567 -- -- -- --
669567
(4 / 1265)
-- --
B6VMMX48K-C 669568 -- -- -- --
669852
(5 / 1465)
669852
(3 / 1430)
--
B6VMMX60K-C 669578 -- -- -- -- -- --
669578
(0 / 1605)
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Numberslistedas0.***arerestrictordiameters,whilenumberslistedas669***areTXVpartnumbers.
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BD-030KB/B4VM-X30K-Bmatch,theappropriateTXVis
the 669565 and 36 ounces of charge will need to be added. (CHANGE
IN CHARGE)
• Forthe*S4BD-024KB/B6EMMX24K-Bmatch,theappropriateTXVis
the669564andnoadditionalchargeneedstobeadded.(NOCHANGES
ARENECESSARY)
Table 4. Restrictor or TXV / Charge Addition (Oz) - Continued
6
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BD- 018KB 024KB 030KB 036KB 042KB 048KB 060KB
ID Restrictor Supplied With OD Unit: 0.048 0.056 0.060, 0.061 0.065, 0.067 0.071, 0.072 0.076, 0.077
Outdoor Unit BOM Charge (Oz.) 40.4 41 40 41 59 60 69.6
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW (SCFM))
C6
C6B(A,H)-X24(C,U)-A 669564
669564
(30 / 530)
669564
(29 / 700)
-- -- -- -- --
C6B(A,H)-X24(C,U)-B 669681
669681
(30 / 600)
669681
(29 / 700)
-- -- -- -- --
C6B(A,H)-X30(C,U)-A 669565 -- --
669565
(36 / 950)
-- -- -- --
C6B(A,H)-X30(C,U)-B 669682 -- --
669682
(36 / 950)
-- -- -- --
C6B(A,H)-X30(C,U)-C 669682 -- --
669682
(36 / 1000)
-- -- -- --
C6B(A,H)-X35(C,U)-A 669566 -- -- --
669566
(31 / 950)
-- -- --
C6B(A,H)-X35(C,U)-B 669683 -- -- --
669683
(31 / 950)
-- -- --
C6B(A,H)-X36(C,U)-B 669683 -- -- --
669683
(31 / 1100)
-- -- --
C6B(A,H)-X36(C,U)-C 669683 -- -- --
669683
(31 / 1100)
-- -- --
C6B(A,H)-X42(C,U)-B 669684 -- -- -- --
669684
(34 / 1250)
-- --
C6B(A,H)-X42(C,U)-C 669684
-- -- -- --
669684
(34 / 1250)
-- --
C6B(A,H)-X42(C,U)-D 669684 -- -- -- --
669684
(34 / 1250)
-- --
C6B(A,H)-X47(C,U)-C 669852 -- -- -- -- --
669852
(36 / 1600)
--
C6B(A,H)-X48(C,U)-C 669852 -- -- -- -- --
669852
(36 / 1600)
--
C6B(A,H)-X48(C,U)-D 669852 -- -- -- -- --
669852
(36 / 1600)
--
C6B(A,H)-X60(C,U)-C 669686 -- -- -- -- -- --
669686
(36 / 1600)
C6B(A,H)-X60(C,U)-D 669686 -- -- -- -- -- --
669686
(36 / 1600)
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Numberslistedas0.***arerestrictordiameters,whilenumberslistedas669***areTXVpartnumbers.
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BD-030KB/B4VM-X30K-Bmatch,theappropriateTXVis
the 669565 and 36 ounces of charge will need to be added. (CHANGE
IN CHARGE)
• Forthe*S4BD-024KB/B6EMMX24K-Bmatch,theappropriateTXVis
the669564andnoadditionalchargeneedstobeadded.(NOCHANGES
ARENECESSARY)
Table 4. Restrictor or TXV / Charge Addition (Oz) - Continued
7
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BD- 018KB 024KB 030KB 036KB 042KB 048KB 060KB
ID Restrictor Supplied With OD Unit: 0.048 0.056 0.060, 0.061 0.065, 0.067 0.071, 0.072 0.076, 0.077
Outdoor Unit BOM Charge (Oz.) 40.4 41 40 41 59 60 69.6
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW (SCFM))
C7-0
C7B(A,H)M01824(C,U)-A
0.048
0.048
(0 / 605)
0.056
(0 / 700)
-- -- -- -- --
C7B(A,H)M01824(C,U)-B
0.055
0.048
(0 / 535)
0.055
(5 / 700)
-- -- -- -- --
C7B(A,H)M030(C,U)-C
0.061 -- --
0.061
(0 / 960)
-- -- -- --
C7B(A,H)M03036(C,U)-A
0.061 -- --
0.061
(0 / 960)
0.067
(10 / 1055)
-- -- --
C7B(A,H)M03036(C,U)-B
0.067 -- --
0.061
(0 / 960)
0.067
(10 / 1055)
-- -- --
C7B(A,H)M03642(C,U)-B
0.071 -- -- --
0.067
(10 / 1055)
0.071
(7 / 1290)
-- --
C7B(A,H)M03648(C,U)-C
0.067 -- -- --
0.067
(10 / 1055)
0.071
(7 / 1290)
0.076
(0 / 1415)
--
C7B(A,H)M042(C,U)-D
0.071 -- -- -- --
0.071
(7 / 1290)
-- --
C7B(A,H)M048(C,U)-C
0.077 -- -- -- -- --
0.077
(6 / 1305)
--
C7B(A,H)M048(C,U)-D
0.077 -- -- -- -- --
0.077
(6 / 1305)
--
C7B(A,H)M060(C,U)-C
0.083 -- -- -- -- -- --
0.083
(12 / 1445)
C7B(A,H)M060(C,U)-D
0.083 -- -- -- -- -- --
0.083
(12 / 1445)
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Numberslistedas0.***arerestrictordiameters,whilenumberslistedas669***areTXVpartnumbers.
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BD-030KB/B4VM-X30K-Bmatch,theappropriateTXVis
the 669565 and 36 ounces of charge will need to be added. (CHANGE
IN CHARGE)
• Forthe*S4BD-024KB/B6EMMX24K-Bmatch,theappropriateTXVis
the669564andnoadditionalchargeneedstobeadded.(NOCHANGES
ARENECESSARY)
Table 4. Restrictor or TXV / Charge Addition (Oz) - Continued
7096460 (Replaces 709307C)
Specifications & illustrations subject to change
without notice or incurring obligations (09/13).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Kelvinator NS4BD-KA/B User guide

NS4BD-KA/B
Kelvinator
Brand
Kelvinator
Model
NS4BD-KA/B
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents