Lincoln Manufacturing Series 1000 User manual

1000serviceexp REV: 1/5/07

SERVICE MANUAL

(INTERNATIONAL)

IMPINGER CONVEYOR OVENS

MODEL SERIES 1000 & 1200

Lincoln Foodservice Products, LLC

1111 North Hadley Road

Fort Wayne, Indiana 46804

United States of America

Phone : (800) 374-3004

U.S. Fax: (888) 790-8193 • Int’l Fax: (260) 436-0735

Technical Service Hot Line

(800) 678-9511

www.lincolnfp.com

Impinger I -–1000 Series Service Manual - International 2

TABLE OF CONTENTS

TABLE OF CONTENTS..............................................................................................................................................2

SEQUENCE OF OPERATIONS 1002/1003...............................................................................................................3

SEQUENCE OF OPERATIONS 1106........................................................................................................................4

SEQUENCE OF OPERATIONS 1028 / 1029 / 1228 / 1229 ......................................................................................5

SEQUENCE OF OPERATIONS 1030........................................................................................................................6

SEQUENCE OF OPERTIONS 1032 ..........................................................................................................................7

SEQUENCE OF OPERATIONS / 1033, 1034, 1046, 1047 .......................................................................................8

SEQUENCE OF OPERATIONS 1042 / 1043 / 1242 / 1243 ....................................................................................10

SCHEMATIC / 1002, 1003 .......................................................................................................................................12

SCHEMATIC / 1006 TO SERIAL NUMBERS Q14279.............................................................................................13

SCHEMATIC / 1028, 1029, S/N Q19071 & BELOW................................................................................................14

SCHEMATIC / 1028, 1029, S/N Q19078 & ABOVE.................................................................................................15

SCHEMATIC / 1030, TO S/N Q17170......................................................................................................................16

SCHEMATIC / 1030, S/N Q17171 & ABOVE...........................................................................................................17

SCHEMATIC / 1032. S/N Q19077 & BELOW ..........................................................................................................18

SCHEMATIC / 1032, S/N Q19078 & ABOVE...........................................................................................................19

SCHEMATIC / 1033, 1034, 1046, 1047 ...................................................................................................................20

SCHEMATIC / 1042, 1043, S/N Q14279 & BELOW................................................................................................21

SCHEMATIC / 1042, 1043, S/N Q14280 & ABOVE.................................................................................................22

SCHEMATIC / 1228. 1229, S/N Q14790 & BELOW................................................................................................23

SCHEMATIC / 1228, 1229, S/N Q14791 & ABOVE.................................................................................................24

SCHEMATIC / 1242, 1243 .......................................................................................................................................25

TROUBLESHOOTING GUIDE 1000 & 1200 / GAS OVENS ..................................................................................26

TROUBLESHOOTING GUIDE 1000 & 1200 SERIES / ELECTRIC OVENS...........................................................39

TROUBLESHOOTING / GAS OVENS 1033, 1034, 1046, 1047..............................................................................46

REMOVAL, INSTALLATION & ADJUSTMENTS .....................................................................................................53

MODEL SERIES 1000 &1200...............................................................................................................................53

PARTS / MODEL SERIES 1000 & 1200 - GENERAL..............................................................................................80

BLOW UP / 1000, 1200 – GENERAL.......................................................................................................................81

PARTS / MODEL 1002-1003 , S/N 2584 TO 4389 ..................................................................................................82

BLOW UP / 1002, 1003 – S/N 2584 to 4389............................................................................................................83

PARTS / MODEL 1002-1003, S/N 4390 & UP.........................................................................................................84

BLOW UP / 1002, 1003 – S/N 4390 & ABOVE........................................................................................................85

PARTS / MODEL 1006.............................................................................................................................................86

BLOW UP / 1006 ......................................................................................................................................................87

PARTS / 1028-1029-1032 ........................................................................................................................................88

BLOW UP / 1028, 1029, 1032 ..................................................................................................................................89

PARTS/ MODEL 1030..............................................................................................................................................90

BLOW UP / 1030 ......................................................................................................................................................91

PARTS / 1042, 1043.................................................................................................................................................92

BLOW-UP / 1042, 1043............................................................................................................................................93

PARTS / 1033, 1034, 1046, 1047.............................................................................................................................94

BLOW-UP / 1033, 1034, 1046, 1047........................................................................................................................95

PARTS / 1228-1229..................................................................................................................................................96

BLOW UP / 1228, 1229 ............................................................................................................................................97

PARTS / 1242, 1243.................................................................................................................................................98

BLOW - UP / 1242, 1243..........................................................................................................................................99

PARTS / OVEN BACK - GAS.................................................................................................................................100

BLOW UP / OVEN BACK – GAS ...........................................................................................................................101

PARTS / OVEN BACK- ELECTRIC........................................................................................................................102

BLOW UP / OVEN BACK – ELECTRIC .................................................................................................................103

PARTS / CONVEYOR MOTOR ASSEMBLY S/N 4390 & ABOVE ........................................................................104

BLOW UP / CONVEYOR MOTOR ASSEMBLY S/N 4390 & ABOVE ...................................................................105

PARTS / SERIES 1000 – CONVEYOR..................................................................................................................106

BLOW UP / SERIES 1000 CONVEYOR ................................................................................................................107

PARTS / SERIES 1200 - CONVEYOR CONTROL................................................................................................108

BLOW UP / SERIES 1200 – CONVEYOR CONTROL ..........................................................................................109

PARTS / SERIES 1200 – CONVEYOR..................................................................................................................110

BLOW UP / SERIES 1200 – CONVEYOR .............................................................................................................111

Impinger I -–1000 Series Service Manual - International 3

SEQUENCE OF OPERATIONS 1002/1003

MODEL 1002 - 240VAC - 50HZ - NATURAL GAS

MODEL 1003 - 240VAC - 50HZ - L.P. GAS

POWER SUPPLY Electrical Power to be supplied to the Oven by a three conductor service.

Black conductor is Hot

Red conductor is Neutral

Green conductor is Ground

CONTROL BOX When the temperature in the Control Box reaches 120°F +

AUTO COOL DOWN 3°, the Cooling Fan Thermostat will switch power to the Control Box Cooling Fan.

The Thermostat will interrupt power to the Cooling Fan when the Control Box

temperature falls to 100°F + 3°.

MAIN FAN CIRCUIT Electrical power is permanently supplied to the normally open contacts of the Double

Pole Main Fan Relay, the Cooling Fan Thermostat, the normally open Double Pole

Main Fan Switch, and the normally open Cool Down Thermostat (thermostat closes

at 160°F and opens at140°F). Closing the Main Fan Switch supplies 240 VAC

through a 3A Fuse to the primary of the control circuit Step down Transformer. The

Transformer steps the voltage down to 120 VAC for the control circuit. 120 VAC is

supplied to the coil of the Double Pole Main Fan Relay. The coil of the relay is

energized. The normally open contacts now close, energizing the Main Fan Motor

through one 10A Fuse. Closing the Fan Switch also supplies power to the Cooling

Fan, Hour Meter (hour meter discontinued after S/N 3484), the 12.6 VAC

Transformer, the Burner and Conveyor Switches.

BURNER CIRCUIT

Closing the Fan Switch and the normally open Burner Switch supplies 120 VAC

through the Air Pressure Switch, to the normally open contacts of the Burner Motor

Relay, and the primary of the 24 VAC Step Down Transformer. The Transformer

secondary supplies 24 VAC to the Relay Coil (the normally open contacts close

within 30 seconds), and the normally open Centrifugal Switch. When the Relay

contacts close, the Burner Blower Motor is energized. As this motor reaches

approximately 1600 R.P.M., its internal centrifugal switch closes, supplying 24 VAC

to the Gas Control Valve. When the Gas Control Valve is supplied with 24 VAC, the

pilot valve is energized, and the igniter circuit is energized. Ignition should now

occur. After pilot flame is proven, the main gas valve is energized. The Burner

Indicator Light is also energized.

CONVEYOR DRIVE

(S/N 100 to 4389)

Closing the Fan Switch and the normally open Conveyor Switch supplies 120 VAC

through a 3A Fuse, to the Motor Control Board. AC volts are converted to D.C. volts

and are supplied to the Conveyor Motor at board terminals A1 and A2 through a

D.P.D.T. Reversing Switch. Adjustment of the Speed Control Potentiometer (500

ohm, 10 turn) will change resistance at terminals S1, S2, and S3 varying the D.C.

voltage to the motor. The speed of the Conveyor Motor will increase or decrease as

the D.C. voltage from the Motor Control Board increases or decreases respectively

(S/N 4390 and UP)

Closing the fan switch and the conveyor switch supplies 120 VAC to the Motor

Control Board. AC volts are converted to DC volts and are supplied to the Conveyor

Motor at terminals A+ and A-. Adjustment of the Speed Control Potentiometer (5,000

ohm 10 turn) will change resistance at terminals P1, P2, and P3 varying the DC

voltage to the motor. The speed of the conveyor motor will increase or decrease as

the DC voltage from the board increases or decreases respectively. As the motor

turns, it drives both the reducer gear box and the tach. generator which supplies a

voltage to the DC motor control board and is used as a reference for maintaining a

constant conveyor speed

Impinger I -–1000 Series Service Manual - International 4

TIME TEMP DISPLAY The Time/Temp Display is energized when the Fan Switch is closed, supplying 120

VAC to the primary of the 12.6 volt Transformer. The secondary output of the

transformer, normally 13 to 14 VAC (depending on input), with a center tap, is

supplied to terminals 1,2, and 3 of the Time/Temp Display. The center tap is terminal

2. The display works on a balanced input and center tap voltage to each leg must be

1/2 the total reading.

The speed side of the Time/Temp. Display uses a slotted disc (cemented to tach.

coupling) to break the infra-red light beam of the optical switch (mounted on gear

motor) producing electrical pulses that are transmitted to the display. The display

converts these pulses into a read-out of minutes and seconds.

The temperature portion of the display uses a Thermistor Probe to sense oven

temperature. The thermistor outputs a resistance proportional to the oven

temperature. This resistance is then converted by the display into a temperature

reading.

SEQUENCE OF OPERATIONS 1106

MODEL 1006 - 240 VAC - 50HZ - 1 PHASE - NATURAL GAS

POWER SUPPLY Electrical Power to be supplied to the Oven by a three conductor service.

Red conductor is Hot

Black conductor is Neutral

Green conductor is Ground

CONTROL BOX AUTO

COOL DOWN

When the temperature in the Control Box reaches 120°F + 3°, the Cooling Fan

Thermostat will switch power to the Control Box Cooling Fan. The Thermostat will

interrupt power to the Cooling Fan when the Control Box temperature falls to 100°F +

3°.

MAIN FAN CIRCUIT Electrical power is permanently supplied to the normally open contacts of the Double

Pole Main Fan Relay, the Cooling Fan Thermostat, and through a 3A Fuse to the

normally open Double Pole Main Fan Switch, and the normally open Cool Down

Thermostat (thermostat closes at 160°F and opens at 140°F). Closing the Main Fan

Switch supplies 240 VAC to the primary of the control circuit Step Down

Transformer. (The transformer steps the voltage down to 120VAC for the control

circuit) 120 VAC is supplied to the coil of the Main Fan Relay. The coil of the Relay is

energized, the normally open contacts now close, energizing the Main Fan Motor

through one 10A fuse. Closing the Fan Switch also supplies power to the Cooling

Fan, the 12.6 VAC Transformer, the Burner and Conveyor Switches

TRANSFORMER (12.6

VAC)

Upon closure of the Fan Switch, 120 VAC is supplied to the primary of the 12.6 VAC

Transformer. The Transformer steps the voltage down to 12.6 VAC (normally 13 to

14 VAC) with a center tap, and supplies power to the Time/Temp Display. The

voltage from each leg of the Transformer's secondary to the center tap should be

one half of the secondary voltage.

BURNER CIRCUIT Closing the Fan Switch and the normally open Burner Switch supplies 120 VAC

through the Air Pressure Switch, to the normally open contacts of the Burner Motor

Relay, and the primary of the 24 VAC Step Down Trans-former. The Transformer

secondary supplies 24 VAC to the coil of the Burner Motor Relay (the normally open

contacts close within 30 seconds), and through the Burner Air Pressure Switch to the

normally open Centrifugal Switch. When the Relay contacts close, the Burner Blower

Motor is energized. As this motor reaches approximately 1600 R.P.M., the Burner Air

Pressure Switch closes, and the motor's internal centrifugal switch closes supplying

24 VAC to the Gas Control Valve. When the Gas Control Valve is supplied with 24

VAC, the pilot valve is energized, and the igniter circuit is energized. Ignition should

now occur. After pilot flame is proven, the main gas valve is energized. The Burner

Indicator Light is also energized.

CONVEYOR DRIVE

(S/N 4390 AND UP)

Closing the fan switch and the normally open conveyor switch supplies 120 VAC to

the Motor Control Board .AC volts are converted to DC volts and are supplied to the

Conveyor Motor at terminals A+ and A-. Adjustment of the Speed Control

Potentiometer (5000 ohm 10 turn ) will change resistance at terminals P1, P2, and

P3 varying the DC voltage to the motor. The speed of the conveyor motor will

Impinger I -–1000 Series Service Manual - International 5

increase or decrease as the DC voltage from the board increases or decreases

respectively. As the motor turns, it drives both the reducer gearbox and the Tach.

Generator. The Tach. Generator is a DC voltage generator, which supplies a voltage

to the DC motor control board and is used as a reference for maintaining a constant

conveyor speed.

TlME/TEMP DISPLAY The Time/Temp. Display is energized when the Fan Switch is closed, supplying 120

VAC to the primary of the 12.6 volt Transformer. The secondary output of the

transformer, normally 13 to 14 VAC (depending on input), with a center tap is

supplied to terminals 1,2, and 3 of the Time/Temp Display. The center tap is terminal

2. The display works on a balanced input and center tap voltage to each leg must be

1,2 the total reading.

The speed side of the Time/Temp. Display uses a slotted disc (cemented to tach.

coupling) to break the infra-red light beam of the optical switch (mounted on gear

motor) producing electrical pulses that are transmitted to the display. The display

converts these pulses into a read-out of minutes and seconds.

The temperature portion of the display uses a Thermistor Probe to sense oven

temperature. The thermistor outputs a resistance proportional to the oven

temperature. This resistance is then converted by the display into a temperature

reading.

SEQUENCE OF OPERATIONS 1028 / 1029 / 1228 / 1229

MODEL 1028 - 380Y/220 VAC - 50 HZ - 3 PHASE

MODEL 1029 - 415Y/240 VAC - 50 HZ - 3 PHASE

MODEL 1228 - 380Y/220 VAC - 50 HZ - 3 PHASE - DUAL BELT

MODEL 1229 - 415Y/240 VAC - 50 HZ - 3 PHASE - DUAL BELT

POWER SUPPLY Electrical Power to be supplied to the Oven by a five conductor service.

Black conductor is Hot

Red conductor is Hot

Orange conductor is Hot

White conductor is Dedicated Neutral

Green conductor is Ground

MAIN FAN CIRCUIT Electrical power is permanently supplied through 3, 50A fuses to the normally open

contacts of the Mercury Contactor. Power is also supplied through 1, 10A fuse to the

normally open contact of the Main Fan Relay, through a 1A Fuse to the normally

open Double Pole Main Fan Switch, and to the normally open Cool-Down

Thermostat (thermostat closes at 160°F and opens at 140°F.) Closing the Main Fan

Switch supplies 220 or 240 VAC to the primary of the control circuit Step Down

Transformer. (The transformer steps the voltage down to 120 VAC for the control

circuit.) 120 VAC is supplied to the coil of the Main Fan Relay. The coil of the relay is

energized, the normally open contacts close, energizing the Main Fan Motor. Closing

the Main Fan Switch also supplies power to the 12.6 VAC Transformer, the Control

Box Cooling Fan, and the Heat and Conveyor Switches.

TRANSFORMER (12.6

VAC)

Upon closure of the Fan Switch, 120 VAC is supplied to the primary of the 12.6 VAC

Transformer. The Transformer steps the voltage down to 12.6 VAC (normally 13 to

14 VAC) with a center tap, and supplies power to the Time/Temp. Display. The

voltage from each leg of the Transformer's secondary to the center tap should be

one half of the secondary voltage.

HEAT CIRCUIT Closing the Fan Switch and the normally open Heat Switch supplies 120 VAC

through the normally open Air Pressure Switch, and the normally closed Hi-Limit

Thermostat (manually re-settable, opens at 190°F) and, the 3A Fuse, to the L1

terminal of the Temperature Control Board, the coil of the Mercury Contactor, and to

the Heat Indicator Light.

TEMPERATURE

CONTROL

When the Heat Switch is closed, 120 VAC is supplied to the Temperature Control.

The Temperature Control Potentiometer (2.5K ohm) is adjusted to desired

temperature. The Thermocouple will provide varying millivolts to the Temperature

Controller. The Temperature Controller switches the L 2 line of the Contactor coils at

intermittent intervals to maintain desired temperatures.

Impinger I -–1000 Series Service Manual - International 6

CONVEYOR DRIVE

(S/N 100 to 4389)

Closing the Fan Switch and the normally open Conveyor Switch supplies 120 VAC

through a 3A Fuse, to the Motor Control Board. AC volts are converted to D.C. volts

and are supplied to the Conveyor Motor at board terminals A1 and A2 through a

D.P.D.T. Reversing Switch. Adjustment of the Speed Control Potentiometer (500

ohm, 10 turn) will change resistance at terminals S1, S2, and S3 varying the D.C.

voltage to the Conveyor Motor. The speed of the Conveyor Motor will increase or

decrease as the D.C. voltage from the Motor Control Board increases or decreases

respectively.

(S/N 4390 and UP

1000 Series)

(S/N 4390 to 14790

1200 Series)

(S/N 14791 & Above

1200 Series

See Page 9

Closing the fan switch and the normally open Conveyor switch supplies 120 VAC to

the Motor Control Board. AC volts are converted to DC volts and are supplied to the

Conveyor Motor at terminals A+ and A-. Adjustment of the Speed Control

Potentiometer (5,000 ohm 10 turn ) will change resistance at terminals P1, P2, and

P3 varying the DC voltage to the motor. The speed of the conveyor motor will

increase or decrease as the DC voltage from the board increases or decreases

respectively. As the motor turns, it drives both the reducer gearbox and the tach.

generator. The tach. generator is a DC voltage generator which supplies a voltage to

the DC motor control board and is used as a reference for maintaining a constant

conveyor speed.

NOTE The 1200 Series Ovens utilize 2 complete conveyor drive systems.

TIME TEMP

DISPLAY(S/N 4390 &

Above1000 Series) S/N

4390-147901200 Series)

(T/T Display S/N

Q14791& Above1200

Series See Page 9

The Time/Temp. Display is energized when the Fan Switch is closed, supplying 120

VAC to the primary of the 12.6 volt Transformer. The secondary output of the

transformer, normally 13 to 14 VAC (depending on input), with a center tap, is

supplied to terminals 1,2, and 3 of the Time/Temp. Display. The center tap is

terminal 2. The display works on a balanced input and center tap voltage to each leg

must be 1/2 the total reading.

The speed side of the Time/Temp. Display uses a slotted.disc (cemented to tach.

coupling) to break the infra-red light beam of the optical switch (mounted on gear

motor) producing electrical pulses that are transmitted to the display. The display

converts these pulses into a read-out of minutes and seconds.

The temperature portion of the display uses a Thermistor Probe to sense oven

temperature. The thermistor outputs a resistance proportional to the oven

temperature. This resistance is then converted by the display into a temperature

reading.

NOTE The 1200 Series Ovens use a Double Pole Double Throw Switch to connect the two

Optical Encoder Assemblies to the Time/Temp. Display. By activating the switch,

either the front or rear belt speed can be shown by the Time/Temp. Display.

SEQUENCE OF OPERATIONS 1030

MODEL 1030 - 220 VAC - 50HZ - 1 PHASE

POWER SUPPLY Electrical Power to be supplied to the Oven by a three conductor service.

Black conductor is Hot

Red conductor is Neutra

Green conductor is Ground

CONTROL BOX

AUTO COOL DOWN

When the temperature in the Control Box reaches 120°F + 3°, the Cooling Fan

Thermostat will switch power to the Control Box Cooling Fan. The Thermostat will

interrupt power to the Cooling Fan when the Control Box temperature falls to 100°F +

3°.

MAIN FAN CIRCUIT Electrical power is permanently supplied to the normally open contacts of the Double

Pole Main Fan Relay, the Cooling Fan Thermostat, the normally open Main Fan

Switch, and the normally open Cool Down Thermostat (thermostat closes at 160°F

and opens at 140°F). Closing the Main Fan Switch supplies 220 VAC through a 3A

Fuse to the (normally open) Burner Switch, and to the control circuit Step Down

Transformer (the transformer steps the voltage down to 120 VAC for the control

circuit) 120 VAC is supplied to the coil of the Main Fan Relay The coil is energized,

the normally open contacts close, supplying 220 VAC through one 10A Fuse to the

Main Fan Motor. 120 VAC is also supplied to the 12.6 VAC Transformer, the

Temperature Controller and the Conveyor Switch.

TRANSFORMER (12.6

VAC)

Upon closure of the Fan Switch, 120 VAC is supplied to the primary of the 12.6 VAC

Transformer. The Transformer steps the voltage down to 12.6 VAC (normally 13 to

Impinger I -–1000 Series Service Manual - International 7

14 VAC) with a center tap, and supplies power to the Time/Temp Display. The

voltage from each leg of the Transformer's secondary to the center tap should be

one half of the secondary voltage

BURNER CIRCUIT Closing the normally open Burner Switch supplies 220 VAC, through the gas

pressure-proving switch, and through the Main Fan Air Pressure Switch, to the

Ignition Control. The combustion motor relay is energized, its normally open contacts

now close, supplying120 VAC to the combustion motor. The normally open

combustion air switch closes upon sensing air. After pre-purge period of between 30

and 60 seconds, the Ignition Transformer is energized and the Main Gas Valve is

energized. Ignition should now occur.

TEMPERATURE

CONTROL

Closing the Fan Switch supplies (through the Step down Transformer) 120 VAC to

the Temperature Control Board. The 2.5K ohm Temperature Potentiometer is

adjusted to desired temperature. The Thermocouple will provide varying millivolts to

the Temperature Controller. The Temperature Controller supplies 120 VAC to the

Solenoid Valve at intermittent intervals to maintain desired temperature.

CONVEYOR DRIVE

(S/N4390-Q17170)

(Conveyor Drive

Q171701 & Above See

Page 9)

Closing the fan switch and the normally open conveyor switch supplies 120 VAC to

the Motor Control Board. AC volts are converted to DC volts and are supplied to the

Conveyor Motor at terminals A+ and A-. Adjustment of the Speed Control

Potentiometer (5,000 ohm 10 turn) will change resistance at terminals P1, P2, and

P3 varying the DC voltage to the Conveyor Motor. The speed of the conveyor motor

will increase or decrease as the DC voltage from the board increases or decreases

respectively. As the motor turns, it drives both the reducer gearbox and the tach.

generator. The tach. generator is a DC voltage generator which supplies a voltage to

the DC motor control board and is used as a reference for maintaining a constant

conveyor speed.

(Time/Temp Display

Q17171 & Above See

Page 9)

The Time/Temp. Display is energized when the Fan Switch is closed, supplying 120

VAC to the primary of the 12.6 volt Transformer. The secondary output of the

transformer, normally 13 to 14 VAC (depending on input), with a center tap, is

supplied to terminals 1,2, and 3 of the Time/Temp. Display. The center tap is

terminal 2. The display works on a balanced input and center tap voltage to each leg

must be 1/2 the total reading.

TIME/TEMP

DISPLAY(Q17171 &

Above See Page 9

The speed side of the Time Temp. Display uses a slotted disc (cemented to tach.

coupling) to break the infra-red light beam of the optical switch (mounted on gear

motor) producing electrical pulses that are transmitted to the display. The display

converts these pulses into a read-out of minutes and seconds.

The temperature portion of the display uses a Thermistor Probe to sense oven

temperature. The thermistor outputs a resistance proportional to the oven

temperature. This resistance is then converted by the display into a temperature

reading.

SEQUENCE OF OPERTIONS 1032

MODEL 1032 - 380Y/220 VAC - 50 HZ - 3 PHASE

POWER SUPPLY Electrical Power to be supplied to the Oven by a five conductor service

Black conductor is Hot

Red conductor is Hot

Orange conductor is Hot

White conductor is Dedicated Neutral

Green conductor is Ground

MAIN FAN CIRCUIT Electrical power is permanently supplied through 3, 50A fuses to the normally open

contacts of the Mercury Contactor. Power is also supplied through one 10A fuse to

the normally open contact of the Main Fan Relay, through a 1A Fuse to the normally

open Double Pole Main Fan Switch, and to the normally open Cool-Down

Thermostat (thermostat closes at 160°F and opens at 140°F.) Closing the Main Fan

Switch supplies 220VAC to the primary of the control circuit Step Down Transformer.

(The transformer steps the voltage down to 120 VAC for the control circuit.) 120 VAC

is supplied to the coil of the Main Fan Relay. The coil of the relay is energized, the

normally open contacts close, energizing the Main Fan Motor. Closing the Main Fan

Switch also supplies power to the 12.6 VAC Transformer, the Control Box Cooling

Impinger I -–1000 Series Service Manual - International 8

Fan, and the Heat and Conveyor Switches.

TRANSFORMER (12.6

VAC)

Upon closure of the Fan Switch, 120 VAC is supplied to the primary of the 12.6 VAC

Transformer. The Transformer steps the voltage down to 12.6 VAC (normally 13 to

14 VAC) with a center tap, and supplies power to the Time/Temp Display. The

voltage from each leg of the Transformer's secondary to the center tap should be

one half of the secondary voltage.

HEAT CIRCUIT Closing the Fan Switch and the normally open Heat Switch supplies 120 VAC

through the normally open Air Pressure Switch, and the normally closed Hi-Limit

Thermostat (manually re-settable, opens at 368°C) through the 3A Fuse, to the

Temperature Control Board, the coil of the Mercury Contactor, and to the Heat

Indicator Light.

TEMPERATURE

CONTROL

When the Heat Switch is closed, 120 VAC is supplied to the Temperature Control.

The Temperature Control Potentiometer (2.5K ohm) is adjusted to desired

temperature. The Thermocouple will provide varying millivolts to the Temperature

Controller. The Temperature Controller switches the L2 line of the Contactor coil at

intermittent intervals to maintain desired temperature.

CONVEYOR DRIVE

(S/N 4390 AND UP)

Closing the fan switch and the normally open conveyor switch supplies 120 VAC to

the Motor Control Board AC volts are converted to DC volts and are supplied to the

Conveyor Motor at terminals A+ and A-. Adjustment of the Speed Control

Potentiometer (5,000 ohm 10 turn ) will change resistance at terminals P1, P2, and

P3 varying the DC voltage to the Conveyor Motor. The speed of the conveyor motor

will increase or decrease as the DC voltage from the board increases or decreases

respectively. As the motor turns, it drives both the reducer gear box and the tach.

generator. The tach. generator is a DC voltage generator which supplies a voltage to

the DC motor control board and is used as a reference for maintaining a constant

conveyor speed.

TIME TEMP DISPLAY The Time/Temp. Display is energized when the Fan Switch is closed, supplying 120

VAC to the primary of the12.6 volt Transformer. The secondary output of the

transformer, normally 13 to 14 VAC (depending on input), with a center tap, is

supplied to terminals 1,2, and 3 of the Time/Temp. Display. The center tap is

terminal 2.The display works on a balanced input and center tap voltage to each leg

must be 1/2 the total reading.

The speed side of the Time/Temp. Display uses a slotted disc (cemented to tach.

coupling) to break the infra-red light beam of the optical switch (mounted on gear

motor) producing electrical pulses that are transmitted to the display. The display

converts these pulses into a read-out of minutes and seconds.

The temperature portion of the display uses a Thermistor Probe to sense oven

temperature. The thermistor outputs a resistance proportional to the oven

temperature. This resistance is then converted by the display into a temperature

reading.

SEQUENCE OF OPERATIONS / 1033, 1034, 1046, 1047

MODEL 1033 / 220 VAC - 50HZ / NATURAL GAS

MODEL 1034 / 220 VAC - 50HZ / L.P. GAS

MODEL 1046 / 240 VAC - 50HZ / NATURAL GAS

MODEL 1047 / 240 VAC - 50HZ / L.P. GAS

POWER SUPPLY Electrical Power to be supplies to the oven by a three-conductor service.

Brown conductor is Hot

Blue conductor is Neutral

Green conductor is Ground

CONTROL BOX AUTO

COOL DOWN

When the temperature in the Control Box reaches 120°F± 3°, the Cooling Fan

Thermostat will switch power to the Control Box Cooling Fan. The Thermostat will

interrupt power to the Cooling Fan when the Control Box temperature falls to

100°F±3°.

MAIN FAN CIRCUIT Electrical power is permanently supplied to the normally open contacts of the oven

fan motor relay, the Cooling Fan Thermostat, and the normally open Oven Fan

Switch. Closing the oven fan switch supplies 220 VAC, through a 3 AMP Fuse, to the

primary of the Power Transformer (the transformer steps the voltage down to 120

VAC for the control circuit). 120 VAC is supplied to the Cooling Fan, the normally

open Conveyor Switch, the Electronic Temperature Control, and to the coil of the

Impinger I -–1000 Series Service Manual - International 9

oven start and cool down relay. Its normally open contacts close, supplying 220 VAC

to the Burner Switch and enabling the 20-minute Time Delay module. The 20-minute

Time Delay module supplies 120 VAC to the oven fan motor relay, these normally

open contacts now close, supplying 220 VAC to the Oven Fan Motor.

TRANSFORMER(12.6V

AC)

Upon closure of the Fan Switch, 120 VAC is supplied to the primary of the 12.6 VAC

Transformer. The Transformer steps the voltage down to 12.6 VAC (normally 13 to 14

VAC) with a center tap, and supplies power to the Time/Temp Display. The voltage

from each leg of the Transformer's secondary to the center tap should be one half of

the secondary voltage.

BURNER CIRCUIT Closing the normally open burner switch supplies 220 VAC through the oven air

pressure switch, the gas inlet pressure switch, the normally closed high limit

thermostat (opens at 368°C) to the ignition control. The combustion motor is now

energized. The normally open burner blower air pressure switch closes upon sensing

air pressure. After a pre-purge period of 30-60 seconds, the main gas valve and the

spark generator are energized. Ignition should now occur. After proving the pilot

flame, and a 30 second delay, the gas control relay and the burner indicator lamp are

energized.

TEMPERATURE

CONTROL

Closing the Fan Switch supplies (through the Step Down Transformer) 120 VAC to

the Temperature Control Board. The Temperature Potentiometer is adjusted to

desired temperature. The Thermocouple will provide varying millivolts to the

Temperature Controller. The Temperature Controller supplies 120 VAC to the

Solenoid Valve at intermittent intervals to maintain desired temperature. (An

electronic flame monitor proves main flame operation in the 1033-1034 models)

CONVEYOR DRIVE Closing the Oven Fan Switch supplies 120 VAC, through the Power Transformer, to

the normally open Conveyor Switch. Closing the Conveyor Switch supplies 120 VAC,

through a 3 AMP Fuse, to the primary of the Conveyor Control Transformer. The

secondary of this Transformer supplies 10 VAC and 29 VAC to the Conveyor Control.

The conveyor control supplies voltage pulses to the Conveyor Control. The Conveyor

Control Potentiometer varies the frequency of these pulses. The motor speed will

increase or decrease, as the frequency of the pulses increase or decrease

respectively.

TIME TEMP DISPLAY Closing the Oven Fan Switch supplies 120 VAC, through the Power Transformer, to

the primary of the Time/Temp. Transformer. The secondary output of the

Transformers, 12.5 to 15 VAC with a center tap, is supplies to terminals 1, 2, and of

the Time/Temp. Display. The display works on a balanced input, and the center tap

voltage to each leg must be 1/2 the total reading.The speed side of the Time/Temp.

Display is supplied, by the Conveyor Control, with the frequency of the pulses to the

Conveyor Motor. This frequency is converted by the Time/Temp. Display into a read

out of minutes and seconds. NOTE: The Conveyor Control uses a sensor and

magnet, mounted on the Conveyor Motor that senses when the motor is not turning. If

the motor is not turning, the Time/Temp Display will show --:-- in the window. The

temperature portion of the display uses a Thermistor Probe to sense oven

temperature. The Thermistor outputs a resistance proportional to oven temperature.

This resistance is then converted by the Display into a temperature reading.

OR:

The temperature portion of the display uses a "J" type thermocouple to measure oven

temperature. The thermocouple generates D.C. millivolts proportional to oven

temperature. This millivolt reading is then converted by the display into a temperature

reading.

Impinger I -–1000 Series Service Manual - International 10

SEQUENCE OF OPERATIONS 1042 / 1043 / 1242 / 1243

MODEL 1042 - 240V - 50HZ - NATURAL GAS

MODEL 1043 - 240V - 50HZ - L.P. GAS

MODEL 1242 - 240V - 50HZ - NATURAL GAS/DUAL BELT

MODEL 1243 - 240V - 50HZ - L.P.GAS/DUAL BELT

POWER SUPPLY Electrical Power to be supplied to the Oven by a three conductor service.

Black conductor is Hot

Red conductor is Neutral

Green conductor is Ground

CONTROL BOX AUTO

COOL DOWN

When the temperature in the Control Box reaches 120°F + 3°, the Cooling Fan

Thermostat will switch power to the Control Box Cooling Fan. The Thermostat will

interrupt power to the Cooling Fan when the Control Box temperature falls to 100°F +

3°.

MAIN FAN CIRCUIT Electrical power is permanently supplied to the normally open contacts of the Double

Pole Main Fan Relay, the Cooling Fan Thermostat, the normally open Double Pole

Main Fan Switch, and the normally open Cool Down Thermostat (thermostat closes

at 160°F and opens at 140°F). Closing the Main Fan Switch supplies 240 VAC

through a 3A Fuse to the primary of the control circuit Step Down Transformer. The

Transformer steps the voltage down to 120 VAC for the control circuit. 120 VAC is

supplied to the coil of the Double Pole Main Fan Relay. The coil of the relay is

energized. The normally open contacts now close, energizing the Main Fan Motor

through one 10A Fuse. Closing the Fan Switch also supplies power to the Cooling

Fan, the 12.6 VAC Transformer the Burner and Conveyor Switches.

TRANSFORMER (12.6

VAC)

Upon closure of the Fan Switch, 120 VAC is supplied to the primary of the 12.6 VAC

Transformer. The Transformer steps the voltage down to 12.6 VAC (normally 13 to

14 VAC) with a center tap, and supplies power to the Time/Temp Display. The

voltage from each leg of the Transformer's secondary to the center tap should be

one half of the secondary voltage.

BURNER CIRCUIT Closing the Fan Switch and the normally open Burner Switch supplies 120 VAC

through the Air Pressure Switch, to the Temperature Control Board, the normally

open contacts of the Burner Motor Relay (Burner Motor Relay discontinued after S/N

14791) and the primary of the 24 VAC Transformer. The transformer's secondary

supplies 24 VAC to the burner motor relay coil (the normally open contacts close

within 30 seconds), and the normally open Centrifugal Switch. When the relay

contacts close, the Burner Blower Motor is energized. As this motor reaches approx.

1,600 R.P.M its internal centrifugal switch closes, supplying 24 VAC to the Gas

Control Valve. When the Gas Control Valve is supplied with 24 VAC, the pilot valve

is energized, and the igniter circuit is energized. Ignition should now occur. After pilot

flame is proven, the Main Gas Valve is energized. The Burner Indicator Light is also

energized.

TEMPERATURE

CONTROL

CONVEYOR DRIVE

(S/N Q14790 & Below,

1200 series

S/N Q14973 & Below,

1000 series)

(S/N Q14791 & Above,

1200 series

S/N Q14974 & Above,

1000 series refer to

Pg. 9)

Closing the Fan Switch and Burner Switch supplies 120 VAC to the Temperature

Control Board. The 1K or 1000 ohm Temperature Potentiometer is adjusted to