Frigidaire CFMV157GBA Installation guide

Brand: Frigidaire

Model: CFMV157GBA

Type: Installation guide

Installation

Instructions

Overthe Range

Microwave Oven

Questions?Call800.GE.CARES(800.432.2737)or Visit,,,,_x_ebsite;,t:Hotpointcom I

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - S_,,ethese

instructions for local inspector's use.

• IMPORTANT - Obse_,'e_,ll

governing codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Consumer.

° Note to Consumer - KeeI)these

instructions for future reterence.

° Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product tailure due to improper installation is not

coxered under the _M_rrantx.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

CZ]

Fora Spanishversionof thismanual, visitour Websiteat Hotpoint.com.

Para consultaruna versionen espa#olde estemanual de instrucciones,visitenuestrositio

deinternet Hotpointcom.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Instructions

CONTENTS

General information

hnportant Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Hood Exhaust ....................................... 4, 5

Damage--Shipment/Installation .............................. 6

Parts Included. ......................................... 6

Tools You Will Need ............................................... 7

Mounting Space ...................................................... 7

Step-by-step installation guide

Placement of Mounting Plate ............................ 8-10

Removing tire Mounting Plate ...................... 8

Finding the _4all Studs .................................. 8

Determining _all Plate l.oration .................. 9

Detemiiuiug Rear Mortaring Screw Locations .. 10

Installation Types .................................. 11-22

[]Outside Top ............................

Exhaust

12-14

Attach Mounting Plate to _4"dl ....... 12

Prepm;lfion of Top Cabinet .......... 13

Install the Damper .................. 13

Mount the Microwave Oven ........ 13, 14

Ac!iust the Exhaust Adaptor .......... 14

Connecting Ductwork .......................... 14

_ Outside Back Exhaust 15-18

Preparing Rear _'_fll for

Outside Back Exhaust .......................... 15

Remove Exhaust Adaptor .................... 15

Attach Mounting Plate to 'Wdl ....... 16

Preparation of Top Cabinet .......... 16

Adapting Microwave Blower

tot Outside Back Exhaust ............... 16, 17

Mount the Microwave Oven .......... 18

_] Redrculating ........................................ 19-22

Attach Mounting Plate to _4"fll ....... 19

Preparation of Top Cabinet .......... 19

Adapting Microwave Blower

fl)r Redrrulation ......................... 20, 21

Mount the Microwave Oveu ..........21, 22

Installing the

Charcoal Filter Accessory .................... 22

Before You Use Your Microwave .......................... 23

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-i)rong grounded outlet.

The installer must peril)ira a ground continuity check

on the power outlet box heft)re begilming the

installation to insure that the outlet box is i)roi)erly

grounded, If not i)roi)erly grounded, or if the outlet

box does not ineet electrical requireu_ei_ts noted

(under EI,ECTRICAI, REQUIREMENTS), a qualified

electrician should be elni_loyed to correct any

deficiencies,

CAUTION: For persona]

safety, remove house fuse

or open circuit breaker

before beghmhag

instaJlation to avoid severe

or fatal shock injury,

CAUTION: For persona] safety, the mounting surface

must be capable of supporting the cabinet load, ha

addition to the added weight of this 63-85 pound

product, plus additional oven loads of up to 50 pounds

or a total weight of 113-135 pounds,

CAUTION: For personal safety, this product cmmot

be installed ha cabinet arrmagements such as an island or

a peninsula. It must be mounted to BOTH a top cabinet

AND a wall,

NOTE: For easier hastaJlation mad personal safety, it is

recolmnended that two people install this product.

IMPORTANT - PLEASE RILM) CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

The power cord of this

appfimace is equipped with

a three-prong (grounding)

plug which mates with a

staaadaJ_d three-prong

(grounding) wall receptacle

to mh_hnize the possibility

of electric shock hazard

from this appliance.

Ensure proper

ground exists

before use

You should have the wall receptacle mad circuit checked

by a qualified electricima to make sure the receptacle is

properly grounded,

Where a stmadaa'd two-prong wall receptacle is

encountered, it is very hnportant to have it replaced

with a properly grounded three-prong wall receptacle,

installed by a qualified electricima.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DI_ORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN ILXTENSION CORD.

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts A(:, 60 Hertz, 15 ami)s and

1.58 kilowatts. This l)roduct inust be connected to a

SUl)ply circuit of the i)roper w)ltage and ti'equency.

Wire size must COlafin'm to the requireu/elatS of the

National Electrical Code or the prewfiling local

code fi_i" this kilowatt rating, The power supply

cord and phlg should be brought to a separate

15- to 20-ami)ere branch circuit single grounded

outlet, The outlet box should be located in the

cabinet above the uficrowave oven. The outlet box

and supply circuit should be installed by a qualified

electrician and confln'n/to the National Electrical

Code or the prewfiling local code.

Installation Instructions

HOOD EXHAUST

NOTE: Read these next two pages only if you plml to vent your exhaust to the

outside. If you plan to recirculate the air back into the room, proceed to page 6.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example ot one possible

ductwork installation.

DUCT PIECES

EQUIVALENT NUMBER

LENGTH x USED

RoofCap 24 Ft. x

12Ft.StraightDuct 12Ft. x

(6" Round)

Rectangular-to-Round 5Ft. x

TransitionAdaptor*

Equivalentlengthsofductpiecesarebasedon actualtests and

reflectrequirementsfor goodventingperformancewith anyventhood.

(1)

Total Length

EQUIVALENT

LENGTH

24 Ft.

12Ft.

5Ft.

41 Ft.

* IMPORTANT: If a rectangula>to-round transition adaptor is used, the bottom cornei_ of the damper

will haxe to be cut to fit, using the tin snips, in order to allow free moxement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example ot one possible

ductwork installation.

EQUIVALENT

DUCT PIECES LENGTH* x

Wall Cap 40Ft.

3 Ft.StraightDuct 3Ft. x

3W' x 10"Rectangular)

(_ 90° Elbow 10Ft. x

NUMBER EQUIVALENT

USED = LENGTH

x (1) = 40Ft.

(1) = 3 Ft.

(2) = 20R.

Equivalent lengths of duct pieces are based on actual tests and

reflect requirements for good venting performance with any vent hood.

Total Length = 63 Ft.

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared

at the time it is const_ ucted by leaving enough space between the wall studs to accommodate exhaust.

Installation Instructions

NOTE: If you need to install ducts, note that the total

duct length of 3V{' x 10" rectangular or 6" diameter

round duct should not exceed 140 equivalent feet.

Outside ventilation requires a HOOD EXHAUST DUCT.

Read the following carefiflly.

NOTE: It is important that venting be installed using

the most direct route and with as tew elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages, Also, make sure dmnpers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate with

a standard 3V{' x 10" rectangular duct.

If a round duct is required, a rectangula_to-round

transition adaptor m list be used. Do not use less than

a 6" diameter duct.

Maximum duct length:

For s;Kisfhctorv air movement, the total duct length of

3¼" x l 0" rectangular or 6" diameter round duct should

not exceed 140 equivalent feet.

Elbows, transitions, wall and roof caps,

etc., present additional resistance to airflow and are

equi\_dent to a section of straight duct which is longer

than their actual physical size. When calculating the total

duct length, add the equi\:dent lengths of all transitions

and adaptors plus the length of all straight duct sections.

The chart below shows you how to calculate total

equi\_dent ductwork length using the approximate feet

of equivalent length of some typical ducts.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Rectangular-to-Round 5Ft. x ( ) = Ft.

Transition Adaptor*

Wall Cap 40 Ft. x ( ) = Ft.

C)_ 90° Elbow 10 Ft. x ( ) = Ft.

l@ 45° Elbow 5Ft. x ( ) = Ft.

90° Elbow 25 Ft. x ( ) = Ft.

45° Elbow 5Ft. x ( ) = Ft.

Roof Cap 24 Ft. x ( ) = Ft.

Straight Duct 6" Roundor 1 Ft. x ( ) = Ft.

3W' x 10" Rectangular

Total Ductwork = Ft.

* IMPORTANT: If a r( ( tangulal_to-round transilion Equival( nl I( ngths o[ du(t piec( s are |)as( d on aclual lests

adaptor is us(d, th( bottom corners of th( (lamp( 1 and rel]( (t re(ltfir( m( nls for good v( riling performan(( x_ith

_ill have to b( cm to fit, using th( lin snips, in ord(l any vent hood.

to allm_ free lllOVelllelll of Ihe dHlllpel,

Installation Instructions

DAMAGE--SHIPMENT/

INSTALLATION

" If the unit is damaged in shipment, return the

unit to the store in which it was bought fin" repair

or rel)laceu/ent,

" If the unit is dainaged by the customer, repair or

replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer

and installer.

PARTS INCLUDED

HARDWARE PACKET

PART QUANTITY

WoodScrews 1

(¼"x2")

ToggleBolts(and 3

wingnuts)(_6" x3")

Self-AligningMachine 3

j Screws(W'-28x 3Y/')

NylonGrommet 2

(formetalcabinets)

You will find the installation hardware contained in

a packet with the trait. Check to make sHre w)tl have

all these parts.

NOTE: Some extra parts are included.

ADDITIONAL PARTS

PART

TOPCABINETTEMPLATE

REAR

WALL

TEMPLATE

INSTRUCTIONS

TopCabinet

Template

RearWall

Template

Installation

Instructions

Separately

Packed

Grease

Filter

Separately

Packed

Exhaust

Adaptor

QUANTITY

Installation Instructions

TOOLS YOU WILL NEED

# 1 and#2Phillipsscrewdriver

Tinsnips(forcutting

damper,if required)

Gloves

Safetygoggles

Pencil

Rulerortapemeasureand

t edge

Scissors

(tocuttemplate,if necessary)

Electricdrill with ¾_",W"and%"

drill bits

Saw(saber,holeor keyhole)

......r..,..r.,..r.,..r.,.T.,..r.,..r.,..r.,.r.,.r..,.r.,..r.,..r.,..r.,iTI

(optional)

Fillerblocksor scrap

woodpieces,if needed

fortop cabinetspacing

(usedonrecessedbottom

cabinetinstallationsonly)

Studfinder or Hammer(optional)

__"__-''-_'-'- Ductandmaskingtape

Level

MOUNTING SPACE

66" or More

fromthe Floor

tothe Topof

the Microwave

Backsplash

BottomEdgeof

CabinetNeedsto

be30" or More

from theCooking

Surface

NOTES:

• The space between the cabinets must be

30" wide and fl'ee of obstructions.

• If the space between the cabinets is greater

than 30", a Filler Panel Kit may be used to fill

in the gap between the microwave oven and

the cabinets. Yore" Owner's Manual contains

the kit nmnber tin" wmr model.

• This microwave oven is fl_r installation over

ranges up to 36" wide.

• When installing the microwave oven beneath

smooth, fiat cabinets, be careful to follow the

instructions on the top cabinet template for

power cord clearmlce.

Installation Instructions

PLACEMENT OF THE MOUNTING PLATE

REMOVING THE MICROWAVE

OVEN FROM THE CARTON/

REMOVING THE MOUNTING PLATE

[]Remove tile installation instructions, filter, glass

tray the exhaust adaptor and the small hardware

bag,. Do not remoxe tile Stxrofoam I)r°tecting, tile

front of tile o_,en.

[]Fold back all 4 carton flaps full) against carton

sides, Then carefifll) roll the oxen and carton oxer

onto the top side, The oxen should be restino, _ in

tile Stx rofoam.

Styrofoam

[]Pull tile carton up and off tile oven.

[] Remove and properly discard plastic bags.

_..._MM Screws

0unting Plate

_ Remove tile 2 screws from tile bottom mounting

plate. Remoxe tile mounting plate and set aside.

This plate will be used with the rear wall template

for mo/mting. REPLACE THE SCREWS,

I-_ FINDING THE WALL STUDS

]Find tile studs, using one of tile following

methods:

i i

Wall

Studs

A. Stud finder--a magnetic device that

locates nails.

B. Use a hammer to tap lightly across tile

motmting sm'face to find a solid sotmd.

This will indicate a stud location.

_}_ Afier the find the bvlocating stud(s),

center

probing tile wall with a small nail to find tile edges

of tile stud. Then place a mark half\vav between

the edges. The center of any a(!jacent studs should

be 16" or 24" fl'om this mark.

_Draw a line down the center of the studs,

THE MICROWAVE MUST BE CONNECTED TO

AT LE&ST ONE WALL STUD,

Installation Instructions

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Template beneath cabinet

with flat bottom

Template beneath cabinet

with recessed bottom

Trimthe rearwall

templatealong

the dotted line.

I)raw averticalline onthe wall at

the centerof the 30" to36" wide

space.Tapethe RearWall Template

onto the wall matching the

centerline andtouchingthe bottom

of thecabinet.

Template aligned with front overhang

on cabinet bottom

Drawaline onthe

backwall equaltothe

depthof the front

overhang.Trimthe

rearwall template

alongthe dotted line.

Trimthe rearwall ...........

templatealong

thedotted line.

Drawaverticallineonthewall at

the centerof the 30"or 36" space.

TapetheRearWallTemplateonto

the wall matchingthe centerlineand

touchingthe bottomcabinetframe.

THE MICROWAVE MUST BE LEVEL. [

Use a lexel to make sure the cabinet bottom is lexel.

Your cabinets may have decorative trim that interieres

with the microwave installation, Remove the decorative

trim to install the microwave i)roperly and to make it

level,

On cabinets with a fl'ont overhang, draw a line on the

back wall at the same depth as the overhang. _Mign the

template to match overhang depth. This will kee I) the

microwave level.

[]Measure the inside depth of the fl'ont overhang.

[]Draw a horizontal line on the back wall to match

the depth of the fl'ont ovefl_ang. See illustration.

[]Draw a vertical line on the wall at the center of the

30" to 36" space. Trim the template on the dotted line.

Tape the Rear X4]_llTemplate to the wall using the

marked centefline and top line as a guide.

Installation Instructions

DETERMINING REAR MOUNTING SCREW LOCATIONS

REAR WALl, TEMPLATE

° o o o o o o o o o o o o o o o o o o o o o o o o o o

CAUTION: "_,_ar glo_es

to axoid cutting finge_

on shaq) edges.

NOTE: The Rear Wall Template serves

to position the bottom mounting plate and

to locate the horizontal exhaust outlet.

_lJse a level to check that the template is positioned

acct _I'_telv,

_ I,ocate and mark at least one stud on the lefi or right

side of the centerline. It is important to use at least one

wood screw mounted firmly in a stud to supl)ort the

weight of the microwave.

Mark three additional, evenly spaced locations for the

supplied toggle bolts.

_ Drill in If is a stud,

holes the ulai'ked locations. there

drill a _(; hole fo_ wood screws. For holes that don't

line up with a stud, drill a :'A" hole tot toggle bolts.

NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

Installation Instructions

INSTALLATION TYPES

This microwave oven is designed fi>r adaptation to

the following three types of ventilation:

A, Outside Top Exhaust (Vertical Duct)

B, Outside Back I_haust (Horizontal Duct)

C, Recirculating (Non-Vented Ductless)

(Choose A, B or C)

NOTE: This microwave is shiI)ped assembled fl>r Outside

Top Exhaust (except fl)r non-vented models). Select the

type of ventilation required for wmr installation and

proceed to that section,

OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

_-_ RECIRCULATING

(NON-VENTED DUCTLESS)

A Charcoal Filter Accessory

ICdt is required fi_r the non-

vented exhaust. (See your

Owner's Manual tot the kit

number.)

Installation Instructions

OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to _Mfll

A2. Prepare Top Cabinet

A3. Check Damper Operation

A4. Mount Microwave Oven

A5. Ac!j ust Exha ust Adaptor

A6. (_onnect Ductwork

I-_ ATTACH THE MOUNTING

PLATE TO THE WALL

Remove the template fl'om the rear wall. The

mounting plate must be secured to the wall using at

least 3 toggle bolts and one wood screw. The wood

screw inust engage a wall stud.

_ Remove the toggle wings fl'om the bolts.

_ Insert the bolts into the mounting plate

through the holes designated to go into drywall

and reattach the toggle wings to '_A"onto each bolt.

To use toggle bolts:

Mounting

Plate

ml,

Spacingfor Toggles

MoreThanWall

-,,,-I_,-,.-!_,_Thickness

ToggleWings

B01tEnd

_ Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Betore tightening the toggle bolts and the

wood screw(s), check again to be sure that the

mounting plate is level and centered leti to right.

CAUTION: Be careflfl to avoid pinching fingers

between the back of the mounting plate and the wall.

_ Tighten all bolts. Pull the plate away fl'om the

wall to hel I) tighten the bolts. Be careflfl not to

ove>torque the toggle bolts.

Installation Instructions

I-_ USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

The top cabinet template will help you locate the top

SUl)port screw holes, power cord and exhaust outlet

locations.

" Read tile instructions on tile TOP CABINET

TEMPLATE.

" Tape it tmderneath tile top cabinet.

" Drill the holes, fi_llowing the instructions on the

TOP CABINET TEMPLATE.

CAUTION: _4ear satety goggles when drilling holes

in tile cabinet bottom.

I-_ INSTALL THE DAMPER

Remove rear

retaining screw

" Place tile microwaxe in its ui)right position.

" Remo_e tile retainin,* screw at tile rear of tile

i/lotoi" door.

" I,ifl tile blower motor door,

" Slide the exhaust adaptor toward the left side and

into the opening,

" The adaptor should be oriented as shown,

I-_ INSTALL THE DAMPER (cont.)

Dam

Reinstallrear

retainingscrew

" Close tile blower cmer with adaptor and reinstall

Fear scYew,

" Remove tape holding tile damper. Tile damper

should pivot easily.

" Tile adaptor can be a(!justed, lett to right and fl'ont

to back, to align with the house exhaust ductwork,

_-'_ MOUNT THE MICROWAVE OVEN

FOR EASIER INSTAI,IATION AND PERSONAl,

SAFETY, X4E RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

NOTE: If yore" cabinet is metal, use tile nvhm

grommet aro/md tile power cord hole to prevent

cutting of tile cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, case damage may occur from

overtightening screws.

NOTE: When too/rating

the iilicrowave oven,

thread power cord

through hole in bottom of

top cabinet. Kee I) it tight

throughout Steps 1-3. Do

not pinch cord or lift

oven by pulling

_ I,ift microwaxe, tilt

it forward and hook

slots at back bottom

edge onto fo/ir lower

tabs of mounting

plate.

->.

_ Rotate front of

o_en

up against cabinet

bottoill.

Installation Instructions

MOUNT THE MICROWAVE

OVEN (cont.)

_]nsert a sell:aligning screw through top center

cabinet hole. Temporarily secure tile oven by

turning tile screw at least two full turns after tile

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord tight.

Be careful not to pinch the cord, especially when

mounting flush to bottom of cabinet.

CabinetFront

Cabinet Bottom Shelf

FillerBlock

__Equivalent

to Depth

of Cabinet

Recess

Self-AligningScrew

MicrowaveOvenTop

[] Insert 2 self:aligning screws

through outer top cabinet

holes, mtlI'II [wo flfll ttlI'nS on

each screw.

Tighten

center

scFew

completely.

[] Tighten tile outer two screws to tile top of tile

microwave oxen. (¥\ hile tightening screws, hold

tile microwaxe oxen in place against tile wall and

the top cabinet.)

_ Install grease filter: See tile Owner's Manual

packed with tile microwave.

ADJUST THE EXHAUST

ADAPTOR

Open tile top cabinet and ac!iust tile exhaust adaptor

to connect to tile house duct.

Damper _

ForFr0nt-t0-Backor

Side-to-SideAdjustment,

Slidethe Exhaust

Adaptoras Needed

CONNECTING DUCTWORK

HouseDuct

_ Extend tile house duct down to connect to

tile exhaust adaptor.

[] Seal exhaust duct joints using duct tape.

Installation Instructions

OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

B1. Prepare Rear _4_dl

B2. Remove Exhaust Adaptor

B3. Attach Mounting Plate to Wall

B4. Prepare Top Cabinet

BS. Adapt Blower for Back Exhaust

B6. Motmt the Microwave Oven

TEMP LATE . .........

PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

The rear wall template should be positioned accm'atel}

as shown on page 9.

" Read the instructions on the REAR X4__I,I,

TEMPI ,ATE.

• Cut the oi)enin_, following, the instHictions of the

REAR X,__I,I, TEMPI,ATE.

Installation Instructions

I-_ ATTACH THE MOUNTING

PLATE TO THE WALL

Remove the template fl'om the rear wall. The

mounting plate must be secured to tile wall using at

least 3 toggle bolts and one wood screw. Tile wood

screw must engage a wall stud,

[]Remove tile toggle wings fl'om tile bolts.

[]Insert tile bolts into tile mounting plate through

tile holes designated to go into drywall and reattach

tile toggle wings to :_A"onto each bolt.

To use toggle bolts:

Mounting

Plate

,,i,(

Spacingfor TogglesMore

-,,-I-,H,-i-,,_ThanWall Thickness

ToggleWings

B01tEnd

_ Place tile motmting plate against tile wall and

insert the toggle wings into the holes in the wall

to I//Otlnt tile plate.

NOTE: Betm'e tightening the toggle bolts and the

wood screw(s), check again to be sure that the

motmting plate is level and centered left to right.

CAUTION: Be careflfl to awfid pinching fingers

between the back of the motmting plate and the wall.

_ Tighten all bolts. Pull the plate away fl'om the

wall to hel I) tighten the bolts. Be carefld not to

ove_=torque the toggle bolts.

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

Tile top cabinet template will hel I) you locate tile top

stlI)I)oFt scI'ew holes and poweI" coi'd Ctltotlt.

* Read the instructions on the TOP CABINET

TEMPI,ATE.

" Tape it tmderneath tile top cabinet.

" Drill the holes, fl)llowing the instructions on the

TOP CABINET TEMPLATE.

CAUTION: X_'ear satety goggles when drilling holes

in tile cabinet bottom.

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

BACK EXHAUST

[] ReIllOXe tile back top center blower illotoi" dooI"

retaining screw.

BlowerMotor_ _.Microwave

BlowerDoor

Screw

_Open tile blower door it tile backb} lifting /l I)

side of the microwaxe. Remo_e and saxe the top

and back retaining screws that hold the blower

iilotoi" ill tile iilici'owa_e.

Retaining

screw

Retaining

screw

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

BACK EXHAUST (cont.)

[] Carefllllv slide the blower motor toward the

right,

and lift it partially out of the opening. Note: The

blower wires are long enough to allow flexible

handling while perfimning these steps. Disconnect

the wires only if it is necessary fin" additional

flexH)ilitv.

Backof

Microwave

[] Remoxe the two screws holding the gray-colored

inlet sleexe to the blower trait. Rotate the gray

sleexe as shown until the gra)' arrow lines up with

the "B", back exhaust. Reinstall the two screws.

Remove screws from

Gray Inlet Sleeve _,.

Back of Microwave

_Roll the assembled blower trait so that the

black-colored exhaust outlet faces the back of

the microwave and the gray-colored inlet sleeve

faces downward. NOTE: The gray-colored sleeve

opening must AI._,_VS thce downward to ensure

proper operation of the microwave.

MustFace

Downward

Black

Exhaust

Outlet

Backof

Microwave

] Tilt and the blower trait back into theplace

oi_ening, in the top of the microwave.

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not

pinched.

_ Secure the blower unit to the microwaxe with

the two screws remoxed in Step 2.

Retaining

screw

Retaining

screw

[] Close the blower coxer.

[]Attach the exhaust adaptor to the rear of the

microwave b) sliding it into the guides at the

top center of the back of the oxen.

Adaptor

Backof

Microwave

Guide

BlowerMotor Screw

LockingTabs

Push in securely until it is in the lower locking

tabs. Take care to assure that the damper hinge

is installed so that it is at the top and that the

damper swings fl'eely. Reinstall the original

blower motor screw through the adaptor and

into the back of the microwave.

Installation Instructions

MOUNT THE MICROWAVE

OVEN

FOR EASIER INSTAI,IATION AND PERSONAI,

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

NOTE: If vour cabinet is metal, use tile nylon

grolmnet around tile power cord hole to prevent

cutting of tile cord.

NOTE: We recommend using filler blocks if tile

cabinet fl'ont hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, ease damage may occur from

overtightening screws.

NOTE: When motmting

tile illicFowa;'e oven,

thread power cord

through hole in bottom of

top cabinet. Keep it tight

throughout Steps 1-3. Do

not pinch cord or lift

oven by pulling cord.

[]I,ifl microwave, tilt

it forward and hook

slots at back bottom

edge onto t()/li" lower

tabs of motmting

plate.

_ Rotate front of

o_en

up against cabinet

bottom.

_lnsert a selt:aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

fight, Be careful not to pinch the cord, especially

when mounting flush to bottom of cabinet,

CabinetFront

CabinetBottomShelf

FillerBlock

T quivalent

to Depth

ofCabinet

Recess

Self-AligningScrew

MicrowaveOvenTop

[] Insert 2 selt:aligning screws

through outer top cabinet

holes. Ttu'n two flfll ttli'ns

on each screw,

_ Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

tile top cabinet.)

_ Install grease filter. See tile Owner's Manual

packed with the microwaxe.

Installation Instructions

RECIRCULATING (Non-VentedDuctless)

INSTALLATION OVERVIEW

C1. Attach Mom_ting Plate to _Mdl

C2. Prepare Top Cabinet

C3. Check Microwave Assemblv

C4. Adapt Blower tin" Recirculation

C5, Mount the Microwave Oven

C6, Install Charcoal Filter

I-_ ATTACH THE MOUNTING

PLATE TO THE WALL

Remove the template flxnn the rear wall. The

motmting plate must be secured to the wall using

at least 3 toggle bolts and one wood screw. The

wood screw inust engage a wall stud.

_ Remove the toggle wings fl'om the bolts.

_ Insert the bolts into the motmting plate through

the holes designated to go into drywall and

reattach the toggle wings to sA" onto each bolt.

To use toggle bolts:

Spacingfor Toggles

MoreThanWall

+l._-,,-j_Thickness

ToggleWings

Mounting

Plate

if,

BoltEnd

_ Place the motmting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Betore tightening the toggle bolts and the

wood screw(s), check again to be sure that the

motmting plate is level and centered left to right.

CAUTION: Be carefld to avoid pinching fingers

between the back of the motmting plate and the wall.

_ Tighten all bolts. Pull the plate away fl'om the

wall to hel I) tighten the bolts. Be carefld not to

ove>torque toggle bolts.

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

The top cabinet template will hel I) you locate the top

st/ppoI't screw holes and power cord CtlH)Ilt locations.

" Read the instructions on the TOP CABINET

TEMPI,ATE.

" Tape it tmderneath the top cabinet.

" Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: _4ear safet} goggles when drilling holes

in the cabinet bottom.

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR RECIRCULATION

_ ReIllO_e the back top center blower illOtoi" dooI"

retaining screw.

Blower Motor-- Backof

Microwave

BlowerDoor

Screw

[]Open the blower door b) lifting it up at the back

side of the microwaxe. Remo_e and saxe the top

and back retaining screws that hold the blower

illotor in the illiCi'OWa_,e.

Retaining

screw

Retaining

screw

[] Carefiflly slide the blower motor toward the right,

and lift it partially out of the opening. Note: The

blower wires are long enough to allow flexible

hai_dling while perfimnii_g these steps. Disconnect

the wires OlflV if it is necessary fl)i" additional

flexibility.

Backof

Microwave

_ Remoxe the two screws holding the gra) colored

inlet sleeve to the blower unit. Rotate the ora_

sleeve as shown tmtil the gra) arrow lines up with

the "R', Recirculating exhaust. Reinstall the two

scYews.

Remove screws from

Gray Inlet Sleeve

x__"

Back of Microwave

_Roll the assembled blower trait so that the

black-colored exhaust outlet laces the fl'ont of

the microwave and the gra._coh)red inlet sleeve

taces downward.

NOTE: The gra}-c )1 _red sleexe o )ening must

AI.\'_YS tace downward to ensure proper

opei'ation of the i//icrowa_e.

Must Face

Downward

Black

Exhaust

OutletFacing

the Front

Backof

Microwave

Page is loading ...

Frigidaire CFMV157GBA Installation guide

Frigidaire CFMV157GBA Installation guide

Frigidaire CFMV157GBA Installation guide

Related papers

Other documents