GE DMCD330GH1WC Owner's manual

Type
Owner's manual
ge.com
!3
L)
Safety Information ........ 2-5
Operating Instructions
Countdown Display .............. 7
Reversing the Door .............. ro
Venting ......................... 8
Care and Cleaning .......... 9
Consumer Support
Consumer Support ..... Back Cover
General Principles
of Good Practice ............... 11
Warranty ..................... 10
DPtCD330
Write the model and serial
numbers here:
Model #
Serial #
Theg are on the Iobel on the front
of the drger behind the door.
175D1807P575 49-90307-1 08-06 JR
iMPORTANTSAFETYiNFORMATiON.
READALLiNSTRUCTIONSBEFOREUSING.
Foryour safety, theinformationin this manual mustbe followed tominimize the risk of fire
or explosion,electric shock, or toprevent property damage,personal injury,or death.
Installation and servicemust beperformed by a qualifiedinstaller, service agencyor
the gas supplier.
FORGASDRYERS:YOUMUSTPOSTIN A PROMINENTLOCATION
1.Instructionsto follow if theuser smellsgas:Contactyourlocal gas
supplier forinformation to be displayed.
Z Instructions concerning flammablematerials as follows:
FORYOURSAFETY:
Do not store or use gasoline or otherflammable vaporsand liquids
in the vicinity ofthis or any otherappliance.
California Safe Drinking Water and Toxic Enforcement Act
This act requires tile governor of California to publish a list of substances known to tile state to
cause cance_; birth defects or other reproductive ham_ and requires businesses to warn custome_
ot potential exposure to such substances.
Gas appliances can Catlse ii/inor exposure to four of these stlbstances, namely benzene, carbon
monoxide, ti)mmldehyde and soot, caused pIJIllaIJly by tile incomplete coIllb/Istion oil nattlI'_ll gas
or 12 fllels.
Properl) ac!justed (h_e_5 will minimize incomplete combustion. Exposure to these substances can be
minimized flu'tiler by properly xenting tile (h) er to tile outdoors.
g_com
PROPERINSTALLAtiON
This dryer must be properly instafled and located in accordance with the Installation Instructions
before it is used. If you did not receive an Installation Instructions sheet, you can receive one by
visiting ge.com, or by calling 800.GE.CARES (800.432.2737).
Properly ground dryer to confimn with all
governing codes and ordinances. Follow details
in the Installation Instructions section.
Install or store where it will not be exposed to
temperatures below fl'eezing or exposed to
the weather:
Connect to a properly rated, protected and sized
power supi)ly circuit to avoid electrical overload.
]_.elnove all shaq) packing itelns and dispose oI
all shiI)ping materials i)ropedy.
In flflfilling the specific needs _ff different
commercial installations, the pro'chaser of this
dryer may wish to locate the coin box and
controls in any _ff a nulnber of locations.
The responsibility fin" the proper pe_f0mmnce
of this work lies solely with the pm'chase_;
It should be done by properly trained and
qualified pe_som_el, and in accordance with
local code requirements.
Any coin box or similar device added to
the (hTeI; either electrically or mechanically,
should be properly grotmded.
Remove any accumulated time by manually
rotating timing cam in the coin box
cotmterclockwise tmfil switch shuts off. Apply
a slight additional cotmterclockwise l)ressure to
fimher seat drive. Make certain not to mrn cam
past switch shutoff position. Otherwise, one
increment of time will be gained. Switches are
offwhen the plastic switch actuating am/ (inner)
is down and all 3 switch buttons are depressed.
Exhaust/Ducting
_] This dD'er MUSTbe exhausted to the outside.
[_ ljse onl) dgid metal 4" diameter ductwork
inside the dI3er cabinet. Use Olfly iigid metal
or flexible metal 4" diameter ductwork fin.
exhausting to the outside. USE OFPLASTICOR
OTHERCOMBUSTIBLEDUCTWORKCANCAUSE
A FIRE.PUNCTUREDDUCTWORKCANCAUSEA
FIREIFIT COLLAPSESORBECOMESOTHERWISE
RESTRICTEDIN USEORDURINGINSTALLATION.
Follow details in the Installation Instructions section.
3
IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
a,
,!
i
YOURLAUNDRYAREA
Keep the area underneath and around wmr
appliances flee (ff c(nnbusfible materials, such
as lint, paper; rags, chemicals, gasoline and
other flammable wq)m_ and liquids.
Keep the floor around your appliances clean
and dry to reduce the possibili b' of slipping.
Keep area aromM the exhaust opening and
SmTotmding areas fl'ee ti'oln tile accumulation
of lint, dust and dirt.
Do not obstruct tile flow of ventilating ai_:
Do not stack or place latm(h_' or throw rugs
against the fl'ont or back ot the dryer
Close supe_Msion is necessm y if this appliance
is used by or near chiMren. Do not allow
children to play on, with or inside this or
any other appliance.
Keep all laundry aids (such as detergents,
bleaches, etc.) ()/it of the reach (ff children,
preterably in a locked cabinet. Observe all
warnings on container labels to avoid iqim>
Never climb on or stand on tile (hTer top.
Do not install or store this appliance where it
will be exposed to the weather;
WHENUSINGYOURDRYER
Never reach into tile (ha'er while tile drum is
moving. Belt}re loading, mdoading or adding
clothes, wait tmtil tile drum has completely
stopped.
Clean the lint filter before each load to prevent lint
accumulation inside tile dryer or in tile room.
DONOTOPERATETHEDRYERWITHOUTTHEtINT
FILTERIN PLACE
Do not wash or d_w articles that have been
cleaned in, washed in, soaked in or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degrease_, dry-cleaning
solvents, kerosene, etc.) which may ignite or
explode. Do not add these substances to the
wash watei: Do not use or place these substances
arotmd yore" washer or (hTer (hmng operation.
Any article on which you have used a cleaning
solvent or that contaii_s flammable materials
(such as cleaning cloths, mops, towels used in
beaut)' salons, restaurants or barber shops, etc.)
nlust not be placed in or near tile (hwer until
solvents or flammable materials have been
removed. There are many highly flammable
items used in homes such as acetone, denatured
alcohol, gasoline, kerosene, some household
cleanei's, SOllle spot i'elllOVei's, ttli])entines,
waxes, wax removei_ and products containing
petroleum distillams.
Tile laundry process can reduce tile flame
retardancv of rid)tics. To avoid such a result,
carefully fi)llow the gaiinent inanufilcturer's
care instructions.
Do not d_y articles containing rubbe_; plastic
or similar materials such as padded bras, temfis
shoes, galoshes, bath mats, rugs, bibs, baby pants,
plastic bags, pillows, etc. that may melt or bm'n.
Some rubber mamfials, when heam(1, can under
certain circumstances produce fire by
spont_l neo/1s COillb/istion.
Do not store plastic, paper or clothing that
may burn or melt on top (ff the d_3'er dining
opei_tion.
Gam_ents labeled OryAway from Heat (>r Do Not
Tumble Dry (such as lifiLjackets containing Kapok)
IlltlSt not be put in yore" (hye_:
Do not city fiberglass articles in your (hwer.
Skin irritation could result fl'om tile remaining
particles that may be picked up by dothing
(linking subsequent dryer uses.
To minimize the possibility of electric shock,
tmplug this appliance fl'om tile power supply or
discom_ect the d_Ter at the distribution panel
b)' removing the time or switching off the drcuit
breaker befi)re attempting any maintenance or
cleaning (except the remox;fl and cleaning ot
tile lint filter). NOTE" Turningthe Cyc/eSelectorknob to
an offposition doesNOTdisconnect theapp/iancefrom
the power supp/y
D(>not spI'}l}' [ln}' t},'pe ot aerosol into, on 0I" near
dryer at anv time.
Do not place items exposed to cooking oils in
veto" (h_'e_: Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
4
ge.com
WHENUSINGYOURDRYER(cont.)
Never attempt to operate this appliance if it is
damaged, nmlflmcdoning, partially disassembled,
or has missing or broken parts, including a
danmged coM or plug.
The interior of the machine and the exhaust
duct connection inside the diTer should be
cleaned at least once a year by a qualified
teclmidan. See the Care and Cleaning section.
Do not rise anv _,,])e of spray cleaner when
cleaning dryer inmrim: Hazardous Runes or
electrical shock could occm:
If vom_ is a gas (hTeI, it is equipped with an
autonmtic electric ignition and does not have
a pilot light. DONOTATTEMPT TOLIGHT WITH
A MATCH. Burns may result fl'onl having your
hand in tile vicinity of tile burner when tile
Ybu may wish to soften your la undered thbrics
or reduce tile static electridw in thenl by using
a due>applied lid)tic softener or an anti-static
conditionei; X_'e recommend you use either
a rid)tic softener in the wash cycle, according
to the manufi_cturer's instructions fin" those
products, or m' a drve>added product fi)r
which the manufi_cturer gives written assurance
on tile package that their product can be safely
used in your (hweI: Service oi" perfimnance
i)rol)lems caused by use of these products are
the responsibility of the manufi_cmreI_ of
those products and are not covered under
the warranP,' to this appliance.
autonmtic ignition turns on.
WHENNOTUSINGYOURDRYER
_- Grasp tile plug firefly when disconnecting this
appliance to avoid damage to tile cord while
pulling. Place tile cord a_v fl'om traffic areas
so it will not be stepped on, tripped over or
subjected to dalnage.
Do not attempt to repair or replace any paI* of
this appliance or attempt any seiMcing unless
specifically recommended in this Owner's Manual
or in published usei:repair instructions that you
undei3tnnd and have the skills to canw out.
Befiwe discarding a chyei; oi" removing it fl'om
service, remove tile (hTer door to prevent
children flxnn hiding inside.
Do not tamper with controls.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS
Reversingthe door.
Tools needed:
Standard#2 Tape-tipped
Phillips screwdriver putty knife
[_ Open the door and remoxe the filler plugs opposite the hinges. _,_ith the
door completely open, remoxe the bottom screw from each hinge on the
dr_er tace. Insert these screws about halt\va_ into the TOP holes, for each
hinoe_, on the opposite side (where you removed the filler plugs).
Apply firm pressure to _oet the screw started in new holes.
_ I,oosen top screw from each hinge on the dryer thce halfway. _,_ith one hand
holding the top of the door and the other hand holding the bottoi/l, i'ei/loxe
the door from the drxer b) lifting it UP and OUT
/
_] Rotate the door 180 . Insert it on the opposKe side of the opemng b) mo_mg
the door I£1/and DOWN tmtil the top hinge and the bottom hinge are resting
on the top screws inserted in step 1.
[_ Remoxe the remaining screws from the side of the o )enino fl'om which
the door was remoxed. _,_ith these screws, secure each hinge at the bottom.
Tighten the two top screws of each hinge Reinsert the plastic )luo-s} 6' on
the side from which the door was remoxed.
Countdowndisplay,fDCCDmodelsonly) ge.com
The countdown display shows the remaining operating time as well as the current drying cycle. The
display board is configured for a 45-minute dry time at the factory to correspond with the 45-minute
timer cam pre-installed in the coin box. If the timer cam is modified for another operating duration,
the dip switches on the display board should be set as follows:
ON
I
O
1 2
DRYINGTIME (minutes)
45
60
90
120
DIP SWITCHNUMBERS
1
1
1
0
0
2
1
0
1
0
NOTE: Thisdisplaydoesnot accumulatet/me.See the following examplesof displaypossiblhties.
DIP SWITCHSETflNG (rain) COINSLIDEACTUATIONS DISPLAYREADING(rain)
45 I 45to 0,then blank
45 2 45to I, then 1for next 45min.,
then 0and blank
120 I 99 for21minutes,then98to 0,
then blank
Ventingthe dryer.
For the best drying pertom_ance, the dxTer needs to be properly vented. The dryer will use more energy
and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the
Installation Instructions.
Use only rigid metal 4" diameter (lu('twork inside the (hTer cabinet. Use only rigid metal or
flexible metal 4" diameter ductwork fi)r exhausting to the outside.
Do not use plastic or other combustible ductwork.
Use the shortest length possible.
Do not crush, kink or collapse the duct.
Avoid resting the duct on shaq_ objects.
Venting must conform to local building codes.
Correct
Venting
Incorrect
Venting
Careand cleaning, gecom
CareandCleaningof theDryer
The Exterior: _ii)e c,r dust an) spills or washing
compounds with a dan_p cloth. Dryer control
panel and finishes mm be damaged by some
latmdry pretreaul/ent soil and stain relno_,er
products. Apply these products awm fl'om tile
(ha'e_: Tile gfl)tic may then be washed and dried
nommllv. Damaoe to _om" (h_er caused b_ these
products is not co',ered by }our warrant_.
The tint Filter: Clean tile lint
filter befiwe each use.
Moisten yore" finge_ and
reach into tile filter opening.
Rim yore" finge_ across tile
filter; Hme a qualified
technician _acuum tile lint
li'OII/ tile dI'?er once aveai:
The Exhaust Duct: Inspect and clean tile exhaust
ducting at least once a year to prevent clogging.
A partially clogged exhaust can lengthen tile
drying time.
Follow these steps."
[_ Tm'n off electrical supply 1)_disconnecting tile
plug fl'om the wall socket.
_ Discmmect tile duct from tile dr_ e_:
[_ Vacuuln tile duct with tile hose attachment and
recom_ect tile duct.
The ExhaustHoo& Check fl'om tile outside that tile
flaps _ffthe hood move ti'eely when operating. Make
sure that there is no wildlife (birds, insects, etc.)
nesting inside the duct or hood.
GECommercialDryer Warranty.
Coin-OperatedModelDMCD330Only
t_ All warranty service provided by our Factory Service Centers,
General Electric Commercial Laundry Distributors or an authorized
Customer Cam®technician. Toget customer support, on-line, visit us
at gecommerciallaundry.com, or call 800.GE.CARES(800.432.2737).
Please hove serial number and model number available when coiling
for service.
Staple sour receipt here.
Proof of the original purchase
dote is needed to obtain
service under the warranty,
For ThePeriod Of." We Will Replace:
90 Days Anypartof the dryer (except the coin s)'stem _',:)which fifils due to a (lefect in materials
From the date of the or workmanship. During this limited90-daywarranty,GE will also provide, freeofcharge,
originalpurchase all labor and related service to replace the defbcfive part,
Three Years Anypart of the dxTer which fails due to a defect in materials or workmanship. During this
From the date of the limited three-year warranty, you will be responsible fi)r any labor and related service costs.
originalpurchase
Fourththrough
FifthYear
Fromthedateof the
originalpurchase
The dryer drum, if it should tail due to a (lefect in materials or workmanship, and the cabinet
side panels, base and cover,if they should tidl due to rust-through. L)m'ing this limited additional
two-year warranty, yon will be responsible tor any labor and related service costs.
What Is Not Covered:
*Coh_ System (including the coin drop meter, coin slide
mechmfislu, coin vault m_d locks) is covered under a
separate manufacturer's warrm_ty. See hlsert for details.
Service trips to your place of business to teach you how
to use the product.
hnproper h_staJlation, delivery or maJntenmlce.
Failure of the product if it is abused, misused, or used
for other than the intended purpose.
Dmnage caused after delivery.
Any and all hnplied warraa_ties of merchmltability and
fitness for a particular purpose.
Replacement of fuses or resetting of circuit breakers at
place of business.
Dmnage to the product caused by accident, fire, floods or
acts of God.
h_cidentaJ or consequential dmnage caused by possible
defects with this appliance.
Product not accessible to provide required service.
Replacement of the light bulb.
EXCLUSION OFIMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this
Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a
particular purpose, are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
commercial use within the USA. If the product is located in an area where service by a GEAuthorized Servicer
is not available, you may be responsible for a trip charge or you may be required to bring the product to an
Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping to your
place of business.
Some states do not aflow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your
legal rights are, consult your local or state consumer affairs office or your state's Attorney General.
Warrantor: General Electric Company.Louisville, KY 40225
/0
AUTOMATI C DRYER
COMMERCIAL APPLICATION
GENERAL ELECTRIC DRYERS
GENERAL PRINCIPLES OF GOOD PRACTICE
(COIN-OPERATED MODELS ONLY)
In fldfilling tile specific needs of dift%rent commercial installations, tile purchaser of this
General Electric automatic d_Ter may wish to locate the coin box and controls in any of
a number of locations. The responsibility for tile proper performance of this work lies
solely with tile purchaser. It should be done 1)y properly trained and qualified personnel,
and in accordance with local code requirements.
In addition, General Electric Company assumes no responsibility or liability' whatsoever to
tile purchaser for any parent infringement expenses, either in the form of damages or legal
costs, where tile alleged inflingement is based on a patent claim including one or more
components added by tile purchaser (i.e., not supplied by General Electric Company with
tile purchased duet).
Set forth below are some general principles which should be followed by persons installing
tile coin box and controls in the desired location. This listing is not all-inclusive, and is
only intended to serve as a general guide. These principles are inmnded to supplement,
not modify, tile Installation Instructions which accompany tile automatic dwer.
I. Any component added to the automauc dryer, either electrically or mechanically,
should be properly grounded.
9. All current-car_Ting metal parts should be isolated flom possible contact by tile usen
3. All wiring should be properly protecmd from sharp edges, burrs, moving parts and other
agencies which migilt cause al)rasion of the insulation on tile conductors.
4. All electrical connecuons should be mechanically secure, and should provide adequate
and reliable electrical contact under conditions, such as vibration, to which they may be
subjected.
5. All electrical components, wires and terminals should be of proper electrical rating for
tile specific application.
6. All insulating materials should remain effective under tile specific conditions to which
they will be exposed (e.g., humidity, temperature, etc.).
7. The installation should not be incompatible with the electrical circuit within the
automatic d_Ter nor in any manner inmrfere with either the safety' devices or tile
sequence of operations of tile cycle which are engineered into tile appliance.
8. Uninsulamd cuirent-cariTing metal parts should have adequate and ensured permanence
of spacing flom other parts.
11
ConsumerSupport.
GEAppliancesWebsite ge.com
Hme a question or need assistance _ith }our appliance? Tr} the (liE Applianres xAebsite 24 hom_ a day,
any da} of tile }ear! For greater comenience and ihster serxice, }(m can no_ do_nlo _d ()_ne_ 's Manu ds,
order parts or e'_en schedule service on-line.
ScheduleService
Expex_ GE repair service is onl) one step awe} fl'om }our do(m Get on-line and schedule x(mr service at
x()ur, convenience 24 hom_ an} de} of the }ear! Or call 8()().(;E.(;_M_ES (800.432.2737) during nora/el
bHsilIess lloHl_.
go.corn
RealLifeDesignStudio ge.com
GE supports tile IJnixw_al Design concept--pxodurts, services and enviromnents that can be used by
people (d all ages, sizes and capabilities. We recognize the need to design tbr a wide range (ff physical and
mental abilities and impaim_ents. For derails of GE's Llnivel_al Design applications, including ldtchen
design ideas fbr people with disabilities, check out our Website today. For tlle heating impaired, please call
800.TDD.GEAC (800.833.4322).
ExtendedWarranties
go.corn
Pro'chase a GE extended warrant} and learn about special discounts that are available while xour warrant}
is still in effect. YOu can purchase it on-line an}time, or call 800.626.2224 dining normal business hom_.
(liE Consumer Home Services will still be there after }our _arrant} expires.
PartsandAccessories
go.corn
Individuals qualified to service their own appliances can have pm_s or accessories sent direcdv to their
homes (VISA, Master( ard and Discover cards are accepted). Order on-line to&_}, 24 hom_ e\w'y clay or
by phone at 800.626.2002 dining normal business hem's.
Nstructions contained in this manual cover procedures to he performed by any user. Other servicing generallg
should he referred to qualified service personnel. Cautionmust he exercised, since improper servicing may cause
unsafe operation.
Contact Us
go.corn
If you are not satisfied with the service you receive fl'omGE, contact us on ore" Website with all tile details
including your phone numbe_; or wlJte to: General Manage_; Customer Relations
GE Appliances, Appliance Park
Ix}uisville, KY 40225
RegisterYourAppliance
Register your new appliance on-line---at your convenience! Timel} produrt _egistration _dll allow for
enhanced c(mmmnication and prompt serxice under the tem/s of }our warranty, should tlle need arise.
YOu ma} also mail in tile pre-plinted registration card included in tile l)acldm"_ matelial.
go.corn
Printed in Canada
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

GE DMCD330GH1WC Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI