Electrolux E36GC76PPS0 Installation guide

Brand: Electrolux

Model: E36GC76PPS0

Type: Installation guide

This manual is also suitable for

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

-- Installation and service must be performed by a qualified installer,

service agency orthe gas supplier.

For Standard

installation:

Gas Cooktop Dimensions

30"(76.2cm)

Min.*

* 30" (76,2 cm) min. for

unprotected cabinet and

24" (61cm) min. for cabinet

with protected bottom surface.

Gas Cooktop Cutout

Dimensions

2"(5,1 cm) Dia.

Opening to route power

cable. Sealopening

routing power cable.

3" (7,6 cm)

4" X 4" (10,2 cm x 10,2 ......

cm) opening to route gas

supply. Seal opening after

routing gas line

Figure 1

**Note: D & Eare critical to the proper

installation of the cooktop. D reflects the

finished dimension. Due to the variation in

countertop materials, it is recommended

to first undercut this dimension, and then

adjust it upon installation of the cooktop.

36 (91,4) 357/8(91,1) 25 (63,5) 73/4(19,7) 35/5//6(91,3) 353/16(89,4) 351/8(89,2) 22 (55,9) 1//8(2,9) Max. 71/2(19,1)

30 (76,2) 297/8(75,9) 25 (63,5) 73/4(19,7) 291sk6(76) 293/16(74,1) 29//8(74) 22 (55,9) 11/8(2,9) Max. 71/2(19,1)

All dimensions are stated in inches and (cm).

NOTE: Wiring diagrams for this cooktop are enclosed in this booklet

Printed in China

318205459 (1307) Rev.A

English - pages 1-8

Espaflol - p_iginas 9-16

Francais - pages 17-23

Wiring Diagram page- 24

For Installation with the optional Stainless Steel Backsplash.

Gas Cooktop Dimensions

* 30" (76,2 cm) min. for

unprotected cabinet and

24" (61 cm) min. for cabinet

with protected bottom surface.

30"(76,2 cm)

Min.*

2"(5,1 cm)

9" (22,9 cm)

Optional Stainless

Steel Backsplash

***Note: Applies only in case

of countertop backwall.

2" (5,1 cm)Dia.

Opening to route power

cable. Seal opening

routing power cable.

Gas Cooktop Cutout Dimensions

Do not slide unit into cabinet cutout.

Protruding screws on the bottom of unit

may damage the bottom front finish.

Figure 2

4" X 4" (10,2 cm x 10,2 cm)

opening to route gas supply.

Seal opening after routing

gas line

7¼" (18,4 cm)

**Note: D & E are critical to the proper

installation of the cooktop. D reflects the

finished dimension. Due to the variation in

countertop materials, it is recommended to

first undercut this dimension, and then adjust

it upon installation of the cooktop.

36 (91,4) 357/8(91,1) 25 (63,5) 73/4(19,7) 351s//6(91,3) 353//6(89.4) 351/8(89,2) 22 (55,9) 11/8(2,9) Max. 71/)(19,1)

30 (76,2) 297/8(75,9) 25 (63,5) 73/4(19,7) 29/5/16(76) 293/16(74,1) 29//8(74) 22 (55,9) 11/8(2,9) Max. 71/)(19,1)

351s//6(91,3)

29/5/16(76)

All dimensions are stated in inches and (cm).

Important Notes to the Installer

1. Read all instructions contained in these installation

instructions before installing the cooktop.

2. Remove all packing material before connecting the

electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Besure to leave these instructions with the consumer.

5. Note: For operation at 2000 ft. elevations above see

level, appliance rating shall be reduced by 4 percent

for each additional 1000 ft.

Important Note to the Consumer

Keep these instructions with your Use and Care Guide for

future reference.

Depth Adjustment Filler Kit

This cooktop isdesigned to replace existing unit. If the

depth of your countertop opening is bigger than 71/4"

(18.4cm) and lessthan 81/2'` (21.6cm) you can order a free

filler kit by calling Service Center at 1-877-4ELECTROLUX

(1-877-435-3287).

For 36" model: #903051-9010

For 30" model: #903051-9100

Optional Items Available:

• A 9" (22.9cm) Stainless Steel Backsplash Kit

#903048-9010 for 36" model or #903048-9100 for 30"

model.

• A Black Knobs Kit #903049-9120 for 36" model or

#903049-9110 for 30" model.

Those kits can be order through the Service Center at

1-877-4ELECTROLUX(1-877-435-3287). However all cost

related to those kits will be at customer charges.

IMPORTANT SAFETY

INSTRUCTIONS

Installation of this cooktop must conform with local

codes or, in the absence of local codes, with the National

Fuel Gas Code ANSI Z223.1/NFPA54--1atest edition in

the United States, or in Canada, with the Canadian Fuel

Gas Code, CAN/CGA B149 and CAN/CGA B149.2.

When installed in a manufactured (mobile) home

installation must conform with the Manufactured

Home Construction and Safety Standard, title 24 CFR,

part 3280 [Formerly the Federal Standard for Mobile

Home Construction and Safety, title 24, HUD (part

280)] or, when such standard is not applicable, the

Standard for Manufactured Home Installation, ANSI/

NCSBCSA225.1 or with local codes where applicable.

This cooktop has been design certified by CSA

International. As with any appliance using gas and

generating heat, there are certain safety precautions you

should follow. You will find them in the Use and Care

Guide, read it carefully.

Air curtain or other overhead hoods, which operate

by blowing a downward air flow on to a range, shall

not be used in conjunction with gas ranges other

than when the hood and range have been designed,

tested and listen by an independent test laboratory

for use in combination with each other,

Be sure your cooktop is installed and grounded

properly by a qualified installer or service

technician,

This cooktop must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA

No, 70--latest edition in the United States, or in

Canada, with the Canadian Electrical Code, CSA

C22,1 Part 1,

The burners can be lit manually during an

electrical power outage, To light a burner, hold a

lit match to the burner head, then slowly turn the

Surface Control knob to LITE, Use caution when

lighting burners manually,

Do not store items of interest to children in

cabinets above the cooktop, Children could be

seriously burned climbing on the cooktop to reach

items.

To eliminate the need to reach over the surface

burners, cabinet storage space above the burners

should be avoided,

Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil,

Excessiveflame is hazardous.

Never use your cooktop for warming or heating

the room. Prolonged use of the cooktop without

adequate ventilation can be hazardous.

Do not store or use gasoline or other flammable

vapors and liquids near this or any other

appliance, Explosions or fires could result.

The electrical power to the cooktop

must be shut off while gas line connections are

being made, Failure to do so could result in serious

injury or death,

13"(33cm)max.depth

forcabinetinstalledabove

cooktop

30"(76,2cm)Min.

ClearanceBetweenthe

TopoftheCooking

PlatformandtheBottom

ofanUnprotectedWood

orMetalCabinet "_.

24" (61 cm)Min.

when Bottom of Wo_

or Metal Cabinet v ,

is Protected by Not

LessThan 1/8" Flame

Retardant Millboard

Covered With Not

LessThan No. 28 MGS

Sheet Steel, 0,01 5"

(0,4 mm) Stainless

Steel, 0,024" (0,6 mm)

Aluminum or 0,020"

(0,5 mm) Copper

18" (45,7 cm)

Min.

2" (5,1 cm) min. distance

between rear edge

of cutout and nearest

combustible surface

above countertop

30" (76,2 cm) min.

clearance between

the top of the

cooking platform and

the bottom of an

unprotected wood or

metal cabinet.

24" (61,X_cm_ l

It is not recommended to use

drawer underneath cooktop.

To eliminate the risk of burns

or fire from reaching over heated surfaces,

cabinet storage space located above the

cooktop should be avoided. If cabinet

storage is provided, risk can be reduced

by installing a range hood that projects

horizontally a minimum of 7" (17,8 cm) 36"(91,4cm) 36"(91,4cm)

beyond the bottom of the cabinets. 30"(76,2cm) 30"(76,2cm)

9" (22,9 cm) 9" (22,9 cm)

5" (12,7 cm) 5" (12,7 cm)

Figure 3 - CABINET DESIGN

Wall Outlet Location

_. 4,,_

(10,2 cm)

(12,7 cm)

Recommended

area for 120V

grounded

outlet on rear _L_cENTRE 16"

wall. _LINE (40,6 cm)

OF UNIT

NOTE: If an : /

outlet is not I

available, have

one installed I

by a qualified i

technician. ____

"_ CCENTR E

][,..LINE

Figure 4 OFUNIT

Provide an Adequate Gas Supply

This cooktop is designed to operate on natural gas at 4"

(10,2 cm) of manifold pressure only.

A pressure regulator is connected in series with the

manifold on the cooktop and must remain in series with

the supply line.

For proper operation, the maximum inlet pressure to

the regulator must be no more than 14" (35,6 cm) of

water column (W.C.) pressure.

For checking the regulator, the inlet pressure must be at

least 1"(2,5 cm) (or 2,5 kPa) greater than the regulator

manifold pressure setting. The regulator is set for 4"

(10,2 cm) of manifold pressure, the inlet pressure must

be at least 5" (12,7 cm).

The gas supply line to the range should be 1/2" (1,3 cm)

or 3/4" (1,9 cm) pipe.

LP/Propane Gas Conversion

This appliance can be used with Natural gas or LP/

Propane gas. It is shipped from the factory for use with

natural gas.

A kit for converting to LPgas is supplied with your

cooktop. The kit is marked "FOR LP/PROPANEGAS

CONVERSION".

The conversion must be performed by a qualified service

technician in accordance with the kit instructions and

all local codes and requirements. Failure to follow

instructions could result in serious injury or property

damage. The qualified agency performing this work

assumes responsibility for the conversion.

Failure to make the appropriate

conversion can result in serious personal injury and

property damage.

Important: Remove all packing material and literature

from cooktop before connecting gas and electrical

supply to cooktop.

Install Pressure Regulator

Install the pressure regulator with the arrow on the

regulator pointing up toward the unit in a position

where you can reach the access cap.

Do not make the connection too tight.

The regulator is die cast. Overtightening may crack the

regulator resulting in a gas leak and possible fire or

explosion.

Manual GAS FLOW Pressure

Shutoff Flare __ Flare Regulator

Valve Union Union

Nipple Flexible

Access

Off Connector

Cap

All connections must be wrench-tightened

Figure 5

Assemble the flexible connector from the gas supply pipe

to the pressure regulator in the following order:

1. manual shutoff valve

2. 1/2" (1,3 cm) nipple

3. 1/2" (1,3 cm) flare union adapter

4. flexible connector

5. 1/2" (1,3 cm) flare union adapter

6. 1/2" (1,3 cm) nipple

7. pressure regulator

Use pipe-joint compound made for use with Natural and

LP/Propane gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not

kinked.

Thesupplylineshouldbeequippedwithanapproved

shutoffvalve.Thisvalveshouldbelocatedinthesame

roomasthecooktopandshouldbeinalocationthat

allowseaseofopeningandclosing.Donotblockaccess

totheshutoffvalve.Thevalveisforturningonor

shuttingoffgastotheappliance.

Open position

Figure 6

Once the regulator is in place, open the shutoff valve in

the gas supply line. Wait a few minutes for gas to move

through the gas line.

Check for leaks. After connecting the cooktop to the

gas supply, check the system for leaks with a manometer.

If a manometer is not available, turn on the gas supply

and use a liquid leak detector (or soap and water) at all

joints and connections to check for leaks.

Do not use a flame to check for leaks

from gas connections. Checking for leaks with a flame

may result in a fire or explosion.

Tighten all connections if necessary to prevent gas

leakage in the cooktop or supply line.

Check alignment of control knob valves after

connecting the cooktop to the gas supply to be sure the

cooktop manifold pipe has not moved. A misalignment

could cause the valve stems to rub on the control panel,

resulting in a gas leak at the valve.

Disconnect this cooktop and its individual shutoff

valve from the gas supply piping system during any

pressure testing of that system at test pressures greater

than 1/2 psig (3,5 kPa or 14" (35,6 cm) water column).

Isolate the cooktop from the gas supply piping

system by closing its individual manual shutoff valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig

(3,5 kPa or 14" (35,6 cm) water column).

Electrical Requirements

120 volt, 60 Hertz, properly grounded branch circuit

protected by a 15 amp circuit breaker or time delay fuse.

Do not use an extension cord with this cooktop.

Grounding Instructions

IMPORTANT Pleaseread carefully.

For personal safety, this appliance must be properly

grounded.

The power cord of this appliance isequipped with a

3-prong (grounding) plug which mates with a standard

3-prong grounding wall receptacle (see Figure 7) to

minimize the possibility of electric shock hazard from the

appliance.

The wall receptacle and circuit should be checked by

a qualified electrician to make sure the receptacle is

properly grounded.

Preferred Method

Grounding type

wall receptacle

Power supply

cord with 3=prong

grounding plug.

Figure 7

Where a standard 2-prong wall receptacle is installed,

it is the personal responsibility and obligation of the

consumer to have it replaced by a properly grounded

3-prong wall receptacle.

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

Disconnect electrical supply cord from

wall receptacle before servicing cooktop.

Cooktop Installation

1. Visually inspect the cooktop for damage.

2. If you are installing the optional Stainless Steel

backsplash, first fix it at the back of the cooktop

using the screws supplied with the kit and follow the

instructions attached.

3. Set the cooktop into the countertop cutout.

NOTE: Do not use caulking compound; cooktop should

be removable for service when needed.

Check Operation

RefertotheUse and Care Guide packaged with the

appliance for operating instructions and for care and

cleaning of your cooktop.

Do not touch the burners. They may be

hot enough to cause burns.

1. Check Burner Cap Placement

Regular burner

It is very important to be sure that all surface burner

caps and burner grates are properly installed and in the

correct locations before operating the appliance. Please

note that the burner heads are secured to the cooktop.

The cooktop is not removable. Do not attempt to remove

or lift the cooktop.

_To prevent flare-ups and avoid creation

of harmful by-products, do not use the cooktop without

all burner caps properly installed to insure proper ignition

and gas flame size.

Always keep the burner caps and burner grates in place

whenever the surface burners are in use. DO not allow

spills, food, cleaning agents or any other material to

enter the gas orifice holder openings.

Check and be sure the size of each burner cap matches

the size of the burner head. Check and be sure that all

round style burner caps are correctly in place on round

burner heads.

Check and be sure that all oval style burner caps are

correctly in place on oval burner heads (if equipped).

Check and be sure that all dual or twin style burner caps

are correctly in place on dual or twin heads (if equipped).

On round style burners, the burner cap lip (Figure 8)

should fit snug into the center of burner head and be

level. Refer to figures 9 & 10 for correct and incorrect

burner cap placement.

Once in place, you may check the fit by gently sliding

the burner cap from side to side (Figure 11) to be sure it

is centered and firmly seated. When the burner cap lip

makes contact inside the center of the burner head you

will be able to hear the burner cap click. Pleasenote that

the burner cap should NOT move off the center of the

burner head when sliding from side to side.

Burner

Head

Fig. 8

Correct Incorrect

Burner Cap Burner Cap

Placement Placement

Fig. 9 A Fig. 10

Fig. 11

Dual Flame burner (if equipped)

Remove all tapes from burner cap Be sure that the dual

flame burner caps are correctly placed BEFOREusing

your cooktop.

Note: There are no burner adjustments necessary on this

cooktop.

Burner Cap

Burner Simmer

Precision Flame

Figure 12

Burner

Head

2,Turnon ElectricalPowerandOpenMainShutoff

Gas Valve

3. Check the Igniters

Operation of electric igniters should be checked after

range and supply line connectors have been carefully

checked for leaks and range has been connected to

electric power.

a. To check for proper lighting, push in and turn a surface

burner knob to the LITE position. You will hear the

igniter sparking.

b. The surface burner should ignite when gas is available to

the burner. Purge air from supply lines by leaving knob

in the LITE position until burner ignites. Each burner

should light within four (4) seconds in normal operation

after air has been purged from supply lines.

c. Visually check that burner has a flame, Once the

burner ignites, the control knob should be turned out

of the LITEposition.

d. Try each surface control knob separately until all

burner valves have been checked. Each burner

location is equipped with a separate electrode.

4. Adjust the "LOW" Setting of Surface Burner Valves

(linear flow)

Testto verify if LOW setting should be adjusted:

a. Push in and turn control to LITE until burner ignites.

b. Push in and quickly turn knob to lowest position.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob.

e. Insert a thin-bladed screwdriver into the hollow valve

stem and engage the slotted screw inside. Flame size

can be increased or decreased with the turn of screw.

Turn counterclockwise to increase flame size. Turn

clockwise to decrease flame size (Figure 13).

Adjust flame until you can quickly turn knob from

LITEto lowest position without extinguishing the

flame. Flame should be as small as possible without

extinguishing.

When All Hookups are Complete

Make sure all controls are left in the OFFposition.

Before You Call for Service

Read the Before You Call for Service Checklist and

operating instructions in your Use and Care Guide.

It may save you time and expense. The list includes

common occurrences that are not the result of defective

workmanship or materials in this appliance.

Refer to your Use and Care Guide for Electrolux Service

phone numbers, or call 1-877-4ELECTROLUX (1-877-

435-3287).

Valve

Stem

Figure 13

Page is loading ...

omc i 0NAI

BObG_E D" ALLUNAG E BRBLEUR

TOP BURNER _GN_IER _EtO_

OPT_0NAL

0UEMA00R _ ENCEND_DO _JrER IOR

BOUGE£ D'ALLU_'IAGE BRULEUR

_ACUl T/_I¸_F¸¸ ................

TOP BU<NER ]GN TEA

QUEMADQR DE ENCENOID0 SLPER_PJR

80UG _ E D" ALLL_nGE-BRb_E_

R]_qT REAR

IGNSW

INTEbC TRASERO

BERECHO

INTERALLUM

o AR

FRENTE OERECHO

rNTERALLUM

0 AV

BKI

_ ENTER REA_

_GN SW

_NT Ea_2 DE

CENT_0 TRAr/RO

0ERECH0

_NTER ALUM

CENmE AR_E_E

BK I BX I

I .............................. CN]:R FRONI

raN sw

INT EW:¸ r)F

TOP BURNER _GNtTE_ _ r

HA R 'N P R R C_N 0 _ZaU]_ U0

0BE D0 6 E CEND]_X_ _J _ _0' rNTER ALLUM

BOUGI E D'AIJ pqAaE BRIJLEUR C N1RF : '_VflN1

lop BU_'NER GN[ R _ _ // tN

0U H£DOR _ NO:NDI_ SUPERI0_ _ AE tt

__ ......... iN RO

LC_2CONNECTtON ALLUHEUR } AV

_NN Cr0R

OC CO EC O L{ EU EP_ALME

c_ou_?

_ POWER CORD

_ _ MSE A I A TERRE -

• MANT _u, D,A[ IMENTAT[ON

DISCONN_CT _K)_IR B:ORE RVICIN<] bNI

I .... t

_EPARA ]0N ] 1 2o 150 332

.................... ALAMBRE [ MED IDA T MP , C J MDDO UL....................................................................... _H4 GAGE U STYI

£2!H_

ABE• ALL WIRES PRIOR TO DISCONNECTION _@LN SERVIC NG CONTROLS

VER!FY PRO2_EROPERATION AFTER SERV C NG

&y2so

F_EAL[ZAR ET HANTEN]MI NTO DE LOS CONTROLESERROR DE

A AMP_RA./FPt£DE CAUSARUN b_NCIONAMINT0 ]NCORRECT0

AVE_ I SSEH NT:

E IOb_ ER CHAQb_ FI AVAN1 L [)E_ANC_H:NT DE CEUX Cl UN ERRUR DE

HRANC_t_ENT PL1 CASR J OPfRA1 ON DANGER_USEVfR r _:R L/J :)ON

f0NCY IONN:P/EN] 0: ,AppAR: IL APRF:S [0tT: _R:pARR? i )N

CENTER REAR RIGHt F_R(_N/ R]GHT REAR

• EFT FRONT LEFT REAR CENTER FRONT _GN S_4 ONSW I(:_N SW

ION S_ _GNSW IGN ,SW _NT ENC r_t¸ _N1¸ ENC 0E rNT £NC T_ASERO

INS ENC BE INT ENC mASER0 IN_ ENC _ CENTROTRA_,ERO FFENTE DERECHO EEREC_O

NTER A_Lt_M IN_ER ALLUMFRENTE rZ0U_RCO _Z0UlER00 CENT_OIZOU_ERDO0E_ :HO

INTE_ ALLUM _N_ER mLUM INTER ALLUM _NTERALLbM 0 AV DAR

G AV 6 AR CENTmE AVANT CENTR_ AR_] ERE

_)_ BURNER IG ITER - /

o _AOOR DE ENC NO DO SUP RIOR

0P 8t,RNE_/ IGNI ER

_xJ _A_0R 0 NC NO b0 _ JP RIOF,_

/OPB(_gG I E_?N RD" ALLBCdAGEIqNI, R BRULEU@ !_ ....................... _ "_ ....................................................... O y l 4CUAB/O(}NI rRN OoEMOOLMOO Lof_OARJ}DE £N_3E@ O0

OU M/_U_UR O N_2 _D UO SC_ L_ R]OR L0C CONNECTION A UMEUR

TOP 8U,_NCRIGNITER

OUEMADOR DE ENCENOIDO SUPERIOR

...... ,....................}?_ ._

318,047110 R V,A

_oP 8bl_N_R IGNITER

0PTIONA•

OUEMA_]R DE ENCENOIDO SUPER_

0PCIO_L

_OUG_E _'6_UMAGE BRULEUR

TOP _U_E_ InSUlTER _ffrn

_T]ONAL

_JEMAD_ _ E_ENDIDO _PERIOR

_C I ONAI

_U61E D'ALLUMAGEBRULEUR

FACULTATIF

TOP BURNER IGNITER

G_JEMADO_ DE ENCE_IOO SUPERIOR

_Jual_ D'ALLUM_GE BRULEb/_

_OP BLm_R I aN I ;ER

BOUa_E 0' ALLUMAGE-_X_ULEUR

DISCONNECT PO_ER BEFO_ c_RV_CrNG UNIT

_V SO

OESCONECTE {A ENER_A ANTES DE REA_]ZAR

EL MANTEN_ENTO DEL ELECTRODOMEST_CO

AVE_TlSSEMENT

C_URANT AVANT D'EFFECTUER LA

REPARATION

- RIGHT REAR

laNS_

INI E_/" TRAsERn

DEmECHO

INTER ALLUH

FZLT....

iaN S_

INT _NC TRASERO

IZOUIE_O0

rNrER _LLUM

G ,_R

E ..........

]NT ENC 0E

r_RENTE EZOUIERDO

]NTER ALLUM

RjGH_¸ _RON_¸

INT ENC DE

FRENTE OEF,EO40

INTER A_LU_

D AV

_ CONNECTOR

EMpALHE

CONNECTEUR

G_OUN0 q

PUESTA A TI_RA

MISEA LA TE_E

PO_ER CORD

PARA r RANS_:'O_E

DF FuEr_zA

CABLE

O" ALIMENTAT[ ON

CAUT ]ON :

IABE_ A[] WI_S PRIOR TO DISCONNECTION t_HEN S_RV[C[NG CONTR01S

_RING ER_C_ CAN CAUSE IMPROPER A_ DAN6EROUS 0PERAT_0N

V_RIFY PRO_R OPeRATiON AFTER SO.VICING

AWS0:

E_IaUE_E _C_ LOS ALA_a_ES ANTES DE DESCONECTAR P_

r_EA_ _ZAR Er MAN_ENIHIENrO 0E LOS C0N1R0_ES ERROR DE

/_A_BRA_£ PtJEOE C/\USAR UN FUNC[0NA_mNTO rNC0RRECIO

Y PZ_ IGROSO VEmlOUC Sl E_ FUNCrONA_mNTO ESTA

CORRECTO DESP,£S _ MANTEN_M_ENTO

AVERT ISSEMEN r :

E_IQUErEr_ CHAaUE F IL AVANr LE DE_ANCHEMENI DE CEUX Cl UNE En_C_ 0_

BRANCHEM_N r¸ mEUr CAUSE_ UNE 0PEAR1¸IC_ DANGEREUSE VE_ _F IEr_ LE CON

FONC_IONNE_NI 0E L'APPA_E]L APRES rOUTE REPA_ATION

RIGH1FRON_ •EFT FRONT

_GN S_ _C_SW

_N_ ENC OE _NT Ewe 0E

FRENTE OERECH0 F_ENTE _ZCUIE_O0

DAY a _V

• EFT REAR RrGHT REAR

IGNS_ [GNS_

IN] E_IRA_ERO [NT_NCTRA_RO

IZQUIEROO DERECH0

[NTERA_LUH [NTERALLUM

G AR DAR

TOP BURNER _GN[TER

OUEMADOR DE ENCENOlOO SUPERIOR

BOOGIE O'ALLUM_OE_BRCLEUR _

TOP BURNER IGNI TER

QUEMADORDE ENCENDIDO SUPERIOR

BUUG[ E O"ALLUMAGE- 8[_ULEUIR

" 1

° T

GNI T_R MODU[E BOARD

CUAORODE MOOULODE ENCENDID0

BLOC CONNECTION ALl Bid UR

Electrolux E36GC76PPS0 Installation guide

Brand: Electrolux

Model: E36GC76PPS0

Type: Installation guide

This manual is also suitable for

Download PDF

report

in other languages

français: Electrolux E36GC76PPS0 Guide d'installation
español: Electrolux E36GC76PPS0 Guía de instalación

Electrolux E36GC76PPS0 Installation guide

This manual is also suitable for

Electrolux E36GC76PPS0 Installation guide

in other languages

Related papers

Other documents