JVC EX-A3 Specification

Category
Home audio sets
Type
Specification
COMPACT COMPONENT SYSTEM
EX-A3
Consists of CA-EXA3 and SP-EXA3
LVT1630-002A
[J, C]
INSTRUCTIONS
English
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
EX-A3[J_C]-frontcover.fm Page 1 Wednesday, December 27, 2006 5:01 PM
G-1
(For U.S.A.)
(For U.S.A.)
(For U.S.A.)
(For U.S.A.)
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of cable entry as practical.
Warnings, cautions and others
EX-A3[J_C].book Page 1 Wednesday, December 27, 2006 3:53 PM
G-2
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMIS-
SIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT
STANDARD ENTITLED “DIGITAL APPARATUS”, ICES-003 OF THE DEPARTMENT OF COMMUNICA-
TIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICA-
BLES AUX APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATE-
RIEL BROUILLEUR: “APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES
COMMUNICATIONS.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
EX-A3[J_C]-gpage.fm Page 2 Friday, January 12, 2007 9:34 AM
G-3
CAUTION — F button!
Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). When installing
the apparatus, ensure that the plug is easily accessible.
The F button in any position does not disconnect the mains line.
When the system is on standby, the STANDBY lamp lights red.
When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION — Touche F !
Déconnectez la fiche secteur pour mettre l’appareil complètement hors tension (le témoin STANDBY
s’éteint). Lors de l’installation de l’appareil, assurez-vous que la fiche soit facilement accessible.
La touche F, dans n’importe quelle position, ne déconnecte pas le système du secteur.
Quand le système est en attente, le témoin STANDBY est allumé en rouge.
Quand le système est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être télécommandée.
Warnings, cautions and others (continued)
EX-A3[J_C]-gpage.fm Page 3 Friday, January 12, 2007 9:34 AM
G-4
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There are no user serviceable parts inside the unit;
leave all servicing to qualified service personnel.
3. CAUTION:
(For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N’ouvrez pas le couvercle supérieur ni le coffret de l’appareil. Il n’y a aucune pièce
réparable par l’utilisateur à l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.
3. ATTENTION:
(Pour les Etats-Unis) Radiation laser de classe II visibles et/ou invisible si l’appareil est ouvert. Ne
regardez pas le rayon.
(Pour le Canada) Rayonnement laser visible et/ou invisible de classe 1M une fois ouvert. Ne pas
regarder directement avec des instruments optiques.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À L’INTERIEUR DE
L’APPAREIL.
[European Union only]
[Union européenne seulement]
EX-A3[J_C]-gpage.fm Page 4 Friday, January 12, 2007 9:34 AM
1
Introduction
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain
the best possible performance from the unit.
Part description .............................3
Features of the main feet and studs ...............4
Using the remote control ..............5
Inserting the batteries into the remote
control...........................................................5
Operating the system from the remote
control...........................................................5
Operating a TV using the remote control........6
Preparation.....................................7
Connecting the antennas................................7
Connecting the speakers ................................8
Connecting a TV .............................................9
Connecting a portable digital audio player....11
Connecting a subwoofer ...............................11
Connecting other digital audio devices .........12
Connecting other analog audio devices........12
Connecting the power cable .........................13
Basic operations..........................14
Using the number buttons.............................14
Turning on the main unit ...............................14
Setting the clock............................................15
Adjusting the volume.....................................16
Turning off the sound temporarily ................. 16
Adjusting the bass/treble...............................16
Enhancing the playback sound (K2) .............16
Auto standby function ...................................17
Changing the brightness of the display
window........................................................18
Turning off the display window......................18
Locking disc ejection.....................................18
Listening to radio broadcasts ....19
Selecting a radio station................................19
Tuning in to a preset radio station.................20
Basic operations of disc/file
playback .......................................21
Playing back a disc .......................................21
Playing back a file .........................................22
Display window on the main unit for
disc/file types ..............................................23
Changing the display in the display
window........................................................26
Stopping playback.........................................27
Resuming playback.......................................27
Pausing playback..........................................28
Advancing the picture frame by frame ..........28
Fast reverse/fast forward search ..................28
Playing back from a position 10 seconds
before..........................................................28
Slow motion playback ...................................29
Skipping to the beginning of a
chapter/track/file .........................................29
Selecting a chapter/track using the number
buttons........................................................29
Skipping at approximately 5 minute
intervals ......................................................29
Selecting a track from the menu screen .......30
Convenient functions of disc/file
playback .......................................31
Playing back a disc/file in the desired order
(Program playback) ....................................31
Playing back a disc/file in a random order
(Random playback).....................................33
Playing back a disc/file repeatedly
(Repeat playback).......................................33
Selecting the audio language, subtitle
language and view angle............................34
Magnifying the picture...................................34
Adjusting the picture quality (VFP)................35
Sharpening the voice sound .........................36
Selecting the headphone surround mode .....36
Creating realistic sound (3D PHONIC) .........37
Selecting the audio volume level of
the DVD ......................................................37
Functions unique to a DVD AUDIO...............38
Introduction
Preparation
Basic operations
Listening to radio broadcasts
Basic operations of disc/file
playback
Convenient functions of
disc/file playback
Table of contents
EX-A3[J_C].book Page 1 Wednesday, December 27, 2006 3:53 PM
Introduction
2
Using the status bar and the
menu bar.......................................39
Playing back a specified part repeatedly
(A-B repeat playback).................................40
Designating the time (Time search) ..............40
Changing the initial settings with
the preference screen .................41
Basic operations ...........................................41
LANGUAGE..................................................41
PICTURE ......................................................42
AUDIO...........................................................43
OTHERS....................................................... 43
Language codes ..........................44
Playing back sources from other
devices..........................................45
Playing back sources from other devices .....45
Selecting the signal gain...............................45
Selecting the output level..............................46
QP LINK........................................................46
Timer .............................................47
Using the sleep timer ....................................47
Using the playback timer...............................48
Using the AV COMPU LINK
function.........................................50
Preparation for the AV COMPU LINK
function .......................................................50
Operating the AV COMPU LINK function .....50
Notes on operation ......................51
Suitable locations for the main unit...............51
Condensation................................................51
Cleaning the main unit ..................................51
License and trademark ................................. 51
Notes on handling ......................................... 52
Notes on discs/files .....................53
Playable disc/file types..................................53
Data hierarchy...............................................56
Handling discs...............................................56
Troubleshooting ..........................57
Specifications ..............................60
Main unit (CA-EXA3).....................................60
Speaker (SP-EXA3)......................................60
Supplied accessories....................................60
Playing back sources from
other devices
Timer
Reference
How to read this manual
This manual explains the operations assum-
ing that you will use the remote control.
Some buttons on the main unit are the same
as those on the remote control. You can use
either button in this case.
Some diagrams in this manual are simplified
or exaggerated for the purpose of explana-
tion.
You can operate some functions differently
from the explanation given in this manual.
Depending on the disc/file, you may not
obtain the explained result even after follow-
ing the operation in this manual.
The following marks refer to the usable
discs/files for the explained function.
EX-A3[J_C].book Page 2 Wednesday, December 27, 2006 3:53 PM
3
Introduction
The numbers refer to the pages in which the parts are explained.
Front view
Refer to “Display window” shown below.
Remote control sensor
Rear view
Display window
Part description
EX-A3[J_C].book Page 3 Wednesday, December 27, 2006 3:53 PM
Introduction
4
The use of three main feet on the bottom of the
main unit enables higher sound quality while main-
taining the stability of the main unit.
In addition, the two studs on the bottom help stabi-
lize the main unit and prevent it from wobbling or
tipping when nudged from above. Because the
studs are slightly shorter than the main feet, the
studs do not come in contact with the mounted sur-
face, leaving the main feet to support the main
unit.
Features of the main feet and studs
Main feet (3)
Stud (1)
Stud
Main feet
Stud (1)
The height of the studs are slightly
shorter than the main feet.
Main unit (rear view)
Main unit
(bottom view)
EX-A3[J_C].book Page 4 Wednesday, December 27, 2006 3:53 PM
5
Introduction
The numbers refer to the pages in which the parts
are explained.
If the effective range of the remote control
decreases, replace both batteries.
CAUTION
Do not expose batteries to heat or flame.
Point the remote control directly at the
front of the main unit.
Do not block the remote control sensor on the
main unit.
Inserting the batteries into
the remote control
Operating the system from
the remote control
R6P (SUM-3)/AA (15F) type dry-cell
batteries (supplied)
Using the remote control
EX-A3[J_C].book Page 5 Wednesday, December 27, 2006 3:53 PM
Introduction
6
You can operate your TV using the remote control
of this system.
1 Slide the remote con-
trol mode selector to
[TV].
2 Hold down [F TV].
• Hold down [F TV] until you finish step 4.
3 Press [ENTER] and release.
4 Press the number buttons to enter
the manufacturer code.
Examples:
For a Hitachi TV: Press [1], then [0].
For a Toshiba TV: Press [0], then [8].
When the manufacturer of your TV has two or
more codes, select the manufacturer codes in turn
and find the one that operates the TV and the
remote control properly.
5 Release [F TV].
NOTE
Manufacturer codes are subject to change with-
out notice. You may not be able to operate the
TV produced by the manufacturer.
After replacing the batteries of the remote con-
trol, set the manufacturer code again.
Operate the remote control by pointing it at the TV.
.
Operating a TV using the
remote control
Remote control
mode selector
Number buttons/
TV RETURN/
100+
Setting the manufacturer code
Manufacturer Code Manufacturer Code
JVC 01 Samsung 12
Hitachi 10 Sanyo 13
Magnavox 02 Sharp 06
Mitsubishi 03 Sony 07
Panasonic 04,
11 Toshiba 08
Philips 14 Zenith 09
RCA 05
Remote
control button
Usage
[
F TV ]
Turns on/off the TV.
[TV/VIDEO]
Changes between the TV and
video input.
[TV CH +/
] Changes channels.
[TV VOL +/
] Adjusts volume.
Number but-
tons (1-9, 0,
100+)
Slide the
remote control
mode selector
to [TV] in
advance.
Selects the
channels.
[TV RETURN]
Changes
between the
previously
selected chan-
nel and the cur-
rent channel.
Using the remote control for the TV
operation
EX-A3[J_C].book Page 6 Wednesday, December 27, 2006 3:53 PM
7
Preparation
Setting up the AM loop antenna
Connecting the AM loop antenna
Turn the AM loop antenna to find the best position
for radio reception.
NOTE
Make sure that the antenna conductors do not
touch any other terminals. This could cause poor
reception.
When radio reception with the supplied FM
antenna is poor, or when using a communal
antenna
When using an antenna other than those supplied
with this system, refer to the operation manuals for
the antenna and converter for details of connec-
tion.
When positioning the antennas, find the best posi-
tion for reception while listening to an actual radio
program (refer to “Listening to radio broadcasts”
on page 19).
Connecting the antennas
AM loop antenna (supplied)
If insulation covers the tips of the
antenna cable, twist and pull off
the insulation.
Main unit (rear view)
FM antenna (supplied)
Main unit (rear view)
FM antenna
Stretch out the FM antenna
to the best position for
radio reception.
Main unit (rear view)
Antenna cable
(not supplied)
Outdoor FM
antenna
(not supplied)
Converter (not sup-
plied: compatible
with 300
C
/75
C
)
Coaxial cable
(not supplied)
Depending on the radio reception
conditions, an FM feeder antenna
(not supplied: compatible with
300 C) can be used. In this case,
a converter (not supplied) is
required.
or
Communal
antenna terminal
Preparation
Do not turn on the power until you complete the connection.
EX-A3[J_C].book Page 7 Wednesday, December 27, 2006 3:53 PM
Preparation
8
The left and right speakers are the same.
IMPORTANT
Improper speaker cable connection reduces the
stereo effect and sound quality.
The supplied speakers are magnetically
shielded, but color irregularity may occur on the
TV depending on some conditions. To prevent
color irregularity, set up the speakers following
the instructions below.
1. Turn off the main power of the TV before
setting up the speakers.
2. Place the speakers enough distance from the
TV so that they do not cause color irregularity
on the TV.
3. Wait for approximately 30 minutes before
turning on the main power of the TV again.
CAUTION
Do not short-circuit the ª and · speaker termi-
nals. Doing so may damage the main unit.
The impedance of speakers connected to the
main unit must be within the range of 4
to 16
.
Do not connect other speakers together with the
supplied speakers. The change in impedance
may damage the main unit and the speakers.
Connecting the speakers
Before connecting the speaker cables, twist and pull off the insulation at
the end of each speaker cable.
Speaker terminal
Speaker cable
Right speaker (rear view)
Speaker cable
(supplied)
Speaker terminal
Speaker cable
Left speaker (rear view)Main unit (rear view)
Black line
Black line
The speakers employ natural wood for the
diaphragm and the cabinet in order to
reproduce the original sound faithfully.
The appearance therefore differs for each
system.
You can detach the speaker cover.
Speaker cover
EX-A3[J_C].book Page 8 Wednesday, December 27, 2006 3:53 PM
9
Preparation
IMPORTANT
Do not connect an S-video cable and a compo-
nent video cable at the same time. Otherwise
the picture may not be played back properly.
Connect the main unit directly to a TV (or a mon-
itor) without routing through a video cassette
recorder (VCR). Otherwise picture distortion
may occur during playback. (Routing the con-
nection through a VCR, however, does not affect
the audio quality.)
Connecting the main unit to a VCR-built-in-TV
may also cause picture distortion during play-
back.
Connecting a TV
Connecting a TV with the [VIDEO]
terminal
TV
To a video terminal
Main unit
(rear view)
Composite video cable (supplied)
Connecting a TV with the [S-VIDEO]
terminal
TV
To an S-video terminal
Main unit
(rear view)
S-video cable (not supplied)
Connecting a TV with the
[COMPONENT VIDEO OUT]
terminals
TV
To component
terminals
Main unit
(rear view)
Component video cable (not supplied)
Main unit
Direct connection
TV (or monitor)VCR
Preparation (continued) Do not turn on the power until you complete the connection.
EX-A3[J_C].book Page 9 Wednesday, December 27, 2006 3:53 PM
Preparation
10
To view an image on the TV screen, select the
video signal type correctly according to the TV
after connecting the main unit to the TV.
1 Turn on the main unit.
• Refer to “Connecting the power cable” on
page 13 and “Turning on the main unit” on
page 14.
2 Press [DVD/CD 3].
• When a disc is loaded, press 7 to stop
playback.
3 Press [SCAN MODE].
• The current video signal type flashes.
4 Press 2 or 3 to select the video
signal type suitable for the TV.
• You can select “INTERLACE” or “PRO-
GRESSIVE”. You can obtain better picture
quality in “PROGRESSIVE” mode than in
“INTERLACE” mode.
• Select “INTERLACE” when connecting to a
TV that is only compatible with interlaced
video signals.
• Select “PROGRESSIVE” when connecting
to a TV that is equipped with a component
terminal and is compatible with progressive
video signals.
5 Press [ENTER].
NOTE
To check the compatibility of your TV, contact
your local JVC customer service center.
All JVC-manufactured progressive TVs and
high-definition TVs are fully compatible with this
system.
Even if the power cable of the main unit is dis-
connected from the AC outlet or the power is
interrupted, the video signal type setting is
stored.
Selecting the video signal type
EX-A3[J_C]-03.fm Page 10 Wednesday, January 24, 2007 3:03 PM
11
Preparation
The audio output signal from the [LINE1 OUT] or
[LINE 2 OUT] terminal is processed to resemble
surround sound when the K2 function, clear voice
function, 3D PHONIC function, or headphone sur-
round mode function is activated. To record raw,
unprocessed sound, turn off these functions. Do not
turn the K2 function on or off while recording sound,
as this may cause intermittent sound output.
An audio signal from a device connected to the
[LINE1 IN] terminal is not output via the [LINE1
OUT] terminal.
When you connect this system with an amplifier-
built-in subwoofer (not supplied), you can enjoy a
more dynamic bass sound. Refer to the manual of
the subwoofer for details.
Press [S.WFR OUT] to select
“S WOOFER ON” (Subwoofer on) in
the display window.
Each time you press [S.WFR OUT], the display
toggles between “S WOOFER ON” and
“S WOOFER OFF” (Subwoofer off).
NOTE
When “S WOOFER ON” is selected, the bass
sound from the left and right speakers is auto-
matically turned down, and the bass sound is
emitted mainly from the subwoofer.
Connecting a portable digital
audio player
Listening to analog sound from a
portable digital audio player
Input
Output
Stereo mini
plug cable
(not supplied)
Portable digital audio player or
other audio device
To an audio output terminal (such as a
headphone terminal)
Main unit (front view)
Outputting analog sound to a
portable digital audio player
Output
Main unit (front view)
Stereo mini
plug cable
(not supplied)
Input
Portable digital audio player or
other audio device
To an audio input terminal
Connecting a subwoofer
Audio cable (not supplied)
(You can use the audio cable supplied
with the amplifier-built-in subwoofer.)
Amplifier-built-in subwoofer
(not supplied)
Main unit
(rear view)
Producing sound from the subwoofer
Preparation (continued) Do not turn on the power until you complete the connection.
EX-A3[J_C].book Page 11 Wednesday, December 27, 2006 3:53 PM
Preparation
12
NOTE
You can output the audio signal from the [LINE 3
DIGITAL OUT] terminal when a loaded disc or a
connected USB mass storage class device is
selected as the source.
Pressing [3D PHONIC] while the audio signal is
being output from the [LINE 3 DIGITAL OUT] ter-
minal may cause intermittent sound output.
Connecting other digital
audio devices
AV amplifier with
a built-in decoder
To an optical digital
input terminal
Optical digital cable
(not supplied)
Optical digital cable
(not supplied)
To an optical digital
output terminal
Output
Output
Main unit
(rear view)
Input
Input
MD player or
satellite receiver
Connecting other analog
audio devices
Listening to sound from an analog
audio device
Main unit (rear view)
Output
Input
Analog audio
device
Audio cable
(not supplied)
For the locations of the remote
control buttons, refer to page 10.
EX-A3[J_C].book Page 12 Wednesday, December 27, 2006 3:53 PM
13
Preparation
The audio output signal from the [LINE1 OUT] or
[LINE 2 OUT] terminal is processed to resemble
surround sound when the K2 function, clear voice
function, 3D PHONIC function, or headphone sur-
round mode function is activated. To record raw,
unprocessed sound, turn off these functions. Do
not turn the K2 function on or off while recording
sound, as this may cause intermittent sound out-
put.
An audio signal from a device connected to the
[LINE 2 IN] terminals is not output via the [LINE
2 OUT] terminals.
Connect the power cable after you complete the
other connections.
The [STANDBY] lamp on the main unit lights up.
Outputting sound to an analog audio
device
Cassette
tape player
Input
Output
Audio cable
(not supplied)
Main unit (rear view)
Connecting the power cable
AC outlet
Main unit
(rear view)
Preparation (continued)
Do not turn on the power until you complete the connection.
EX-A3[J_C].book Page 13 Wednesday, December 27, 2006 3:53 PM
Basic operations
14
IMPORTANT
Slide the remote control mode
selector to [AUDIO].
Examples:
5: [5]
15: [ 10]
[1]
[5]
150: [ 10] [ 10] [1] [5] [0]
Press [
F
AUDIO] (or
F
on the main
unit).
The power of the main unit turns on and the
[STANDBY] lamp on the main unit turns off.
Press [
F
AUDIO] again to turn off the power of
the main unit.
With the power off, pressing any of the following
buttons also turns on the main unit.
- [DVD/CD 3], [USB MEMORY 3], [FM/AM],
[LINE] or 0 on the remote control
- s[DVD/CD 3/8], [USB MEMORY 3/8], [FM/
AM/LINE] or 0 on the main unit
The function assigned to the button starts work-
ing at the same time.
Remote control
mode selector
Number
buttons
Using the number buttons
Turning on the main unit
Basic operations
EX-A3[J_C].book Page 14 Wednesday, December 27, 2006 3:53 PM
15
Basic operations
You can set the clock when the main unit is on or
off.
Example: To set the clock to 10:30 a.m. on
Wednesday
1 Press [CLOCK/TIMER].
2 Press 2 or 3 to select the hour.
Hold down 2 or 3 to incrementally increase
the hour setting.
• You can also use the number buttons to
specify the hour.
3 Press [ENTER].
4 Press 2 or 3 to select the minute.
• Hold down 2 or 3 to incrementally
increase the minute setting.
• You can also use the number buttons to
specify the minute.
5 Press [ENTER].
6 Press 2 or 3 to select the day of
the week.
• Hold down 2 or 3 to change the setting for
the day of the week.
• Abbreviations are used for the days of the
week.
SUNSunday
MONMonday
TUETuesday
WEDWednesday
THUThursday
FRIFriday
SATSaturday
7 Press [ENTER].
• The clock starts from 0 seconds in the
minute you set.
NOTE
While setting the clock, you can return to the
previous step by pressing [CANCEL].
The time display on the main unit is a 12-hour
clock.
The clock gains or loses approximately 1 minute
per month.
If the power cable of the main unit is discon-
nected from the AC outlet or the power is inter-
rupted, the clock setting is stored for
approximately 1 minute.
Press [CLOCK/TIMER] repeatedly to
display the clock, and then adjust the
clock starting from step 2.
Press [DISPLAY].
Refer to “Changing the display in the display
window”. (Refer to page 26.)
Setting the clock
Adjusting the clock
Displaying the clock when using this
system
Basic operations (continued)
EX-A3[J_C]-04.fm Page 15 Thursday, February 1, 2007 1:48 PM
1 / 1

JVC EX-A3 Specification

Category
Home audio sets
Type
Specification

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document