Metra 99-7869 Specification

99-7869
Metra
Brand
Metra
Model
99-7869
Category
Mounting kits
Type
Specification

Metra 99-7869 allows you to seamlessly integrate an aftermarket radio into your 2005-2010 Honda Odyssey. It offers multiple radio provision options, including DIN, ISO mount, double DIN, and stacked ISO mount units, providing flexibility for your specific needs. The kit includes all necessary brackets, trim plates, and hardware for a secure and professional installation. It also features a pocket for a clean and organized look. Get ready to elevate your audio experience with Metra 99-7869!

Metra 99-7869 allows you to seamlessly integrate an aftermarket radio into your 2005-2010 Honda Odyssey. It offers multiple radio provision options, including DIN, ISO mount, double DIN, and stacked ISO mount units, providing flexibility for your specific needs. The kit includes all necessary brackets, trim plates, and hardware for a secure and professional installation. It also features a pocket for a clean and organized look. Get ready to elevate your audio experience with Metra 99-7869!

INSTALLATION INSTRUCTIONS FOR PART 99-7869
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio provision
• Stacked ISO Mount Units Provision
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Trim Plate • E) Double DIN Brackets • F) Pocket
• G) Panel Clips - (2) Panel Clips supplied - user asembly onto rear of Radio Housing required
KIT COMPONENTS
99-7869
A
APPLICATIONS
Honda Odyssey
2005-2010
Phillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench
B
C
D
E
F
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1721 - Honda/Acura harness 1998-up
• 70-1722 - Honda harness 2006-up
• 40-HD10 - Honda antenna adapter 2005-up
TOOLS REQUIRED:
G
Dash Disassembly
Honda Odyssey 2005-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Kit Assembly
Din Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . .2
ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . 3
Double Din Radio Provision . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 4
Stacked ISO Mount Units Provision. . . . . . . . . . . . . . . . . . . . . . . . 5
Final
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TABLE OF CONTENTS
99-7869
99-7869
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove climate control
panel below radio.
(Figure A)
2
HONDA ODYSSEY 2005-2010
Remove (3) Phillips-7 MM screws
securing the radio to remove.
(Figure B)
3
DASH DISASSEMBLY
A
B
99-7869
KIT ASSEMBLY
2
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down.
(Figure B)
2
Attach (2) Panel Clips to Radio
Housing rear connectors.
(Figure A)
1
B
Slide the aftermarket radio into the
cage and secure. (
Figure C)
3
Snap the pocket into the housing.
(
Figure D)
4
C
D
A
R
EAR VIEW - RADIO HOUSING
INSTALL
(2) CLIPS
DIN RADIO PROVISION WITH POCKET
3
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit.
(Figure B)
2
Slide the head unit into the radio
opening until the side clips engage.
(
Figure C)
3
Snap the Trim plate into the Radio
Housing.
(Figure C)
4
Snap the Pocket into the Housing.
(Figure D)
5
ISO MOUNT RADIO PROVISION WITH POCKET
B
R
EAR VIEW - RADIO HOUSING
INSTALL
(2) CLIPS
A
C
D
99-7869
KIT ASSEMBLY
Attach (2) Panel Clips to Radio
Housing rear connectors.
(Figure A)
1
99-7869
KIT ASSEMBLY
4
Cut and remove the center bar from
the 99-7869 radio housing.
(Figure B)
2
Snap the Double DIN trim plate into
the radio housing.
(Figure D)
5
Snap the Double DIN brackets to the
inside edge of the 99-7869 radio
housing. (
Figure C)
3
Slide the Double DIN radio into the-
bracket/trim plate assembly and
secure the radio to the assembly
using the screws supplied with the
radio. (
Figure D)
4
DOUBLE DIN RADIO PROVISION
B
C
D
Attach (2) Panel Clips to Radio
Housing rear connectors.
(Figure A)
1
REAR VIEW - RADIO HOUSING
INSTALL
(2) CLIPS
A
5
STACKED ISO MOUNT UNITS PROVISION
B
C
D
99-7869
KIT ASSEMBLY
Cut and remove the center bar from
the 99-7869 radio housing.
(Figure B)
2
Snap the Double DIN trim plate into
the radio housing.
(Figure D)
5
Snap the Double DIN brackets to the
inside edge of the 99-7869 radio
housing. (
Figure C)
3
Slide the Stacked ISO units into the
bracket/trim plate assembly and
secure the units to the assembly
using the screws supplied with the
radio. (
Figure D)
4
Attach (2) Panel Clips to Radio
Housing rear connectors.
(Figure A)
1
REAR VIEW - RADIO HOUSING
INSTALL
(2) CLIPS
A
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B)
Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-7869
KIT ASSEMBLY
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
INST99-7869
REV. 04/21/10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra 99-7869 Specification

99-7869
Metra
Brand
Metra
Model
99-7869
Category
Mounting kits
Type
Specification

Metra 99-7869 allows you to seamlessly integrate an aftermarket radio into your 2005-2010 Honda Odyssey. It offers multiple radio provision options, including DIN, ISO mount, double DIN, and stacked ISO mount units, providing flexibility for your specific needs. The kit includes all necessary brackets, trim plates, and hardware for a secure and professional installation. It also features a pocket for a clean and organized look. Get ready to elevate your audio experience with Metra 99-7869!

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents